QCI-IDNMOD1SMART QX/V4 NFC Module

SRSM.ENV_SENSOR.01 Manual FCC ID: QCI-IDNMOD1 IC: 4302A-IDNMOD1 1.Connector definition PIN Number Name Description 1 3V OUT 3.3V voltage output by the module 2 USB DP USB signal 3 GND Ground 4 USB DM USB signal 5 MCU INT Reserved 6 I2C SDA Reserved 7 I2C SCL Reserved 8 GND Ground 9 UART TX Reserved 10 UART RX Reserved 11 5VM 5V power supply 12 5VM 5V power supply 2.Antenna Area The sensing area of the antenna is shown in the figure below: 3.Instructions After the USB2.0 host is connected to this module, NFC-related functions can be operated through the USB CCID interface. 4.Label There will be a silkscreen of the module model on the PCB of the module FCC warning: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. The separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and different antenna configurations. Warning: The module is limited to OEM installation ONLY The antenna installation must be professional installation, and does not permit use of any antenna with the transmitter; the permitted types of antenna must be specified. The module cannot be sold via retail to the general public or by mail order; it must be sold to authorized dealers or installers only. The end product intended use is not for consumers and general public; rather device is generally for industrial/commercial use. The installation shall be performed by trained licensed professionals, it uses specialized software and adjusts the best angles and orientations, which are difficult for ordinary people to do. The module is limited to installation in mobile or fixed application. The OEM integrator is responsible for ensuring the end-user has no manual instruction to remove or install module; Modular approval allows installation in different end-use products by an original equipment manufacturer (OEM) with limited or no additional testing or equipment authorization for the transmitter function provided by the IDNMOD1. Specifically: •No additional transmitter compliance testing is required if the module is operated with the antenna listed in the document below. •No additional transmitter-compliance testing is required if the module is operated with the same general type of antenna (i.e. near-field segmented loop, circularly polarized patches) as those listed in this User’s Guide and in the FCC filing for the IDNMOD1. Acceptable antennas must be of equal or less far field gain than the antenna previously authorized under the same FCC ID, and must have similar in band and out of band characteristics. In addition, the end product must comply with all applicable FCC equipment authorizations, regulations, requirements and equipment functions not associated with the IDNMOD1. For example, compliance must be demonstrated to regulations for other transmitter components within the host product, to requirements for unintentional radiators (Part 15B), and to additional authorization requirements for the non-transmitter functions. The OEM applying the IDNMOD1 is required to include all FCC and/or IC statements and warnings detailed in the following sections to the end product labeling (where specified) and in the finished product manual. The OEM must also strictly adhere to antenna and installation guidelines and MPE restrictions stated in this document. The finished product manual must contain the following statement: The host product shall use physical label stating "contains trnasmitter module FCC ID: QCI-IDNMOD1" or "contains FCC ID: QCI-IDNMOD1" IC: 4302A-IDNMOD1" or "contains IC: 4302A-IDNMOD1" WARNING: The Federal Communications Commission warns that changes or modifications of the radio module within this device not expressly approved by SMART Technologies ULC. could void the user’s authority to operate the equipment. In the case where an OEM seeks class B (residential) limits for the host product, the finished product manual must contain the following statement: Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed a…

Text truncated - open the document above for the full version.

Cover SMART Board ® MX|MXPro seriesinteractivedisplays Installationandmaintenanceguide SBID-MX255-V4|SBID-MX265-V4|SBID-MX275-V4|SBID-MX286-V4 SBID-MX255-V4-PW|SBID-MX265-V4-PW|SBID-MX275-V4-PW|SBID-MX286-V4-PW SBID-MX255-V3/V3N|SBID-MX265-V3/V3N|SBID-MX275-V3/V3N|SBID-MX286-V3/V3N SBID-MX255-V3-PW/V3N-PW|SBID-MX265-V3-PW/V3N-PW|SBID-MX275-V3-PW/V3N-PW|SBID-MX286-V3-PW/V3N-PW SBID-MX055-V3/V3N|SBID-MX065-V3/V3N|SBID-MX075-V3/V3N|SBID-MX086-V3/V3N SBID-MX055-V3-PW/V3N-PW|SBID-MX065-V3-PW/V3N-PW|SBID-MX075-V3-PW/V3N-PW|SBID-MX086-V3-PW/V3N-PW SBID-MX255-V2-C|SBID-MX265-V2-C|SBID-MX275-V2-C|SBID-MX286-V2-C SBID-MX255-V2-CPW|SBID-MX265-V2-CPW|SBID-MX275-V2-CPW|SBID-MX286-V2-CPW SBID-MX255-V2|SBID-MX265-V2|SBID-MX275-V2|SBID-MX286-V2 SBID-MX255-V2-PW|SBIDMX265-V2-PW|SBID-MX275-V2-PW|SBID-MX286-V2-PW SBIDMX365|SBID-MX375|SBID-MX386|SBIDMX265|SBID-MX275|SBID-MX286 IDX55-4|IDX65-4|IDX75-4|IDX86-4|IDX55-3|IDX65-3|IDX75-3|IDX86-3|IDX55-2|IDX65-2|IDX75-2|IDX86-2 Wasthisdocumenthelpful? smarttech.com/docfeedback/171555 smarttech.com/kb/1715552 Learnmore ThisguideandotherresourcesforSMART Board MXandMXProseriesinteractive displaysareavailableintheSupportsectionoftheSMART website (smarttech.com/support).ScanthisQR codetoviewtheseresourcesonyour mobiledevice. ENERGYSTARisthegovernment-backedsymbolforenergyefficiency,providingsimple,credible,andunbiasedinformationthatconsumersand businessesrelyontomakewell-informeddecisions.ENERGYSTAR-certifiedproductsarethesimplechoiceforenergyefficiency,makingiteasyfor consumersandbusinessestomakepurchasesthatsavethemmoneyandprotecttheenvironment.TheU.S.EPAensuresthateachproductthatearnsthe labelisindependentlycertifiedtodeliverthequality,performance,andsavingsthatusershavecometoexpect. Asshipped,yourdisplaydeliversENERGYSTARperformanceandsavings.However,changingsomesettingsmayincreaseenergyconsumptionbeyond thelimitsrequiredforENERGYSTARcertification.Forexample,increasedbrightnessandcontrastwillincreasepowerconsumption. Pleaseconsidertheenvironmentwhenyouchoosenon-ENERGYSTARsettings. Trademarknotice SMART Board,smarttech,theSMARTlogoandallSMARTtaglinesaretrademarksorregisteredtrademarksofSMART Technologies ULCintheU.S.and/orothercountries.All third-partyproductandcompanynamesmaybetrademarksoftheirrespectiveowners. Copyrightnotice ©2022 SMART Technologies ULC.Allrightsreserved.Nopartofthispublicationmaybereproduced,transmitted,transcribed,storedinaretrievalsystemortranslatedinto anylanguageinanyformbyanymeanswithoutthepriorwrittenconsentofSMART Technologies ULC.Informationinthismanualissubjecttochangewithoutnoticeanddoes notrepresentacommitmentonthepartofSMART. Thisproductand/orusethereofiscoveredbyoneormoreofthefollowingU.S.patents: www.smarttech.com/patents June15,2022 smarttech.com/kb/1715553 Importantinformation Important Therearecriticalsoftwareupdatesforthedisplaythatyouneedtoinstalltoensurethedisplayisfully functionalandprovidesthebestexperience.Connectthedisplaytoawiredorwirelessnetworkwith Internetaccesstoautomaticallydownloadandapplytheseupdatesaswellasfutureupdates. Warning l Failuretofollowtheinstallationinstructionsincludedwiththedisplaycouldresultininjuryand productdamagewhichmaynotbecoveredbythewarranty. l Donotopenordisassemblethedisplay.Youriskelectricalshockfromthehighvoltageinsidethe casing.Openingthecasingalsovoidsthewarranty. l Donotstand(orallowchildrentostand)onachairtotouchthesurfaceofthedisplay.Rather, mounttheproductattheappropriateheight. l Toreducetheriskoffireorelectricshock,donotexposethedisplaytorainormoisture. l Ifthedisplayrequiresreplacementparts,makesuretheservicetechnicianusesreplacement partsspecifiedbySMART Technologiesorpartswiththesamecharacteristicsastheoriginal. l Ensurethatanycablesthatcrossthefloortothedisplayareproperlybundledandmarkedto avoidatriphazard. l Donotinsertobjectsinsidethecabinetventilationholes,becausetheycouldtouchdangerous voltagepointsandcauseelectricshock,fireorproductdamagewhichmaynotbecoveredby thewarranty. l Donotplaceheavyobjectsonthepowercable.Damagetothecablecouldcauseshock,fireor productdamagewhichmaynotbecoveredbythewarranty. l Use onlyextensioncordsandoutletsthatcanfullyaccommodatethedisplay’spolarizedplug. l Usethepowercableprovidedwiththedisplay.Ifapowercableisnotsupplied,contactyour supplier.UseonlypowercablesthatmatchtheACvoltageofthepoweroutletandthatcomply withyourcountry’ssafetystandards. l Iftheglassisbroken,donottouchtheliquidcrystal.Topreventinjury,handleglassfragments withcarewhendisposingofthem. Importantinformation smarttech.com/kb/1715554 l Donotmoveormountthedisplaybyconnectingropeorwiretoitshandles.Thedisplayisheavy, andfailureoftherope,wireorhandlecouldleadtoinjury. l UseonlyVESA ® -approvedmountsifusingamountotherthantheonesuppliedwiththedisplay.. l Disconnectallofthedisplay’spowercablesfromthewalloutletandseekassistancefrom qualifiedservicepersonnelifanyofthefollowingoccur: o Thepowercableorplugisdamaged o Liquidisspilledintothedisplay o Objectsfallintothedisplay o Thedisplayisdropped o Structuraldamage,suchascracking,occurs o Thedisplaybehavesunexpectedlywhenyoufollowoperatinginstructions l BeforeinsertingorremovinganOPSfromthedisplay,turnoffthedisplayusingtheswitchatthe backofthedisplay.SeeOpenPluggableSlotcomputer(OPS)disclaimerformoreinformation. Caution l Turnoffthedisplaybeforecleaningitsscreen.Otherwise,youmayscramblethedesktopiconsor inadvertentlyactivateapplicationswhenyouwipethescreen. l Avoidsettingupandusingthedisplayinanareawithexcessivelevelsofdust,humidity,and smoke. l Makesureanelectricalsocketisnearthedisplayandremainseasilyaccessibleduringuse. l ThedisplayshouldbeusedonlywithEuropeanTNandTTpowerdistributionsystems. Itisnotsuitableforolder,IT-typepowerdistributionsystemsfoundinsomeEuropeancountries. Thissystem(IT-type)iswidelyusedisolatedfromearth,insomeinstallationsinFrance,with impedancetoearth,at230/400V,andinNorway,withvoltagelimiter,neutralnotdistributed,at 230Vline-to-line. Contactqualifiedpersonnelifyou’reuncertainofthetypeofpowersystemavailablewhere you’r…

Text truncated - open the document above for the full version.

SMART Technologies ULC 3636 Research Road NW Calgary, AB T2L 1Y1 CANADA Phone 403.245.0333 Fax 403.228.2500 [email protected] www.smarttech.com Federal Communications Commission 2022-10-20 Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: QCI-IDNMOD1 To Whom It May Concern: This letter is to ascertain that SMART Technologies Inc. QX/V4 NFC Module, Model: IDNMOD1 has been the unit(s) used for conducting FCC compliance testing by EMTEK (SHENZHEN) CO., LTD. The SDoC portion has been conducted in accordance with FCC SDoC requirement as per Section 2.1077 compliance information. We hereby state that we will add responsible party information on the Supplier’s Declaration of Conformity before shipping. Your assistance on this matter is greatly appreciated. If you have any question or concerns, pls. contact us. Sincerely, Nicole McMillan / Manager, Systems Design, Regulatory and Compliance SMART Technologies Inc.

Rev 1/26/2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 01-31-2023 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: QCI-IDNMOD1 SMART Technologies Inc. ("the applicant") certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, (Applicant signature) (Applicant printed name) Nicole McMillan Rev 1/26/2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 01-31-2023 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: QCI-IDNMOD1 SMART Technologies Inc. (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, (Applicant signature) (Applicant printed name) Nicole McMillan

SMART Technologies ULC 3636 Research Road NW Calgary, AB T2L 1Y1 CANADA Phone 403.245.0333 Fax 403.228.2500 [email protected] www.smarttech.com Federal Communications Commission 2023-03-31 Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Ref: Attestation Statements Part 2.911(d)(7) Filing FCC ID: QCI-IDNMOD1 To Whom It May Concern: SMART Technologies Inc. (“the applicant”) certifies that, as of the date of the filing of the application, SMART Technologies (Seattle) Inc. is our designated U.S. agent for service of process for the above referenced FCC ID. SMART Technologies Inc. accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. SMART Technologies (Seattle) Inc. accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information: Name: SMART Technologies (Seattle) Inc. FRN: 0033599457 Address: 2401 4th Ave, 3rd Floor Seattle, WA 98121 USA Contact Person: Sean MacKellar Email: [email protected] Sincerely, Applicant: Agent: SMART Technologies Inc. SMART Technologies (Seattle) Inc. Nicole McMillan Sean MacKellar

Date: 2023-1-4 SUBJECT: FCC Application for FCC ID: QCI-IDNMOD1 To Whom It May Concern: the limited module installed are compliant In addition, the end product must comply with all applicable FCC equipment authorizations, regulations, requirements and equipment functions associated with the IDNMOD1. For example, compliance must be demonstrated to regulations for other transmitter components within the host product, to requirements for unintentional radiators (Part 15B), and to additional authorization requirements for the non-transmitter functions. The OEM applying the IDNMOD1 is required to include all FCC and/or IC statements and warnings detailed in the following sections to the end product labeling (where specified) and in the finished product manual. The OEM must also strictly adhere to antenna and installation guidelines restrictions stated in this document. The finished product manual must contain the following statement: The host product shall use physical label stating "contains trnasmitter module FCC ID: QCI- IDNMOD1" or "contains FCC ID: QCI-IDNMOD1" IC: 4302A-IDNMOD1" or "contains IC: 4302A-IDNMOD1" Host device brand name SMART Board host device models： IDX86-4, SBID-MX086-V4, IDQX86-1, SBID-QX086, SBID-QX086-P, SBID-QX286, SBID-QX286-P; IDX75-4, SBID-MX075-V4, IDQX75-1, SBID-QX075, SBID-QX075-P, SBID-QX275, SBID-QX275-P; IDX65-4, SBID-MX065-V4, IDQX65-1, SBID-QX065, SBID-QX065-P, SBID-QX265, SBID-QX265-P; IDX55-4, SBID-MX055-V4 Regards, Nicole McMillan SMART Technologies Inc.

RF_734_02 04 April 16 Modular Approval Request FCC (KDB 996369 D01 & Part 15.212) FCC ID: QCI-IDNMOD1 Items to be covered by Single modular transmitters. Answer from applicant 1. The modular transmitter must have its own RF shielding. No shield, please see exhibition external photos 2. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over-modulation. Yes, the modular has buffer modulation /data inputs 3. The modular transmitter must have its own power supply regulation. Yes, please see the schem.pdf 4. The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204(b)(c). The antenna must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable). Yes, the requirements of antenna connector and spurious emission have been fulfilled. Please refer to the test report exhibition. 5. The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing. This is intended to demonstrate that the module is capable of complying with Part 15 emission limits regardless of the device into which it is eventually installed. No, module was tested with the Host device brand name: SMART Board; Host device models: IDX86-4, SBID-MX086-V4, IDQX86-1, SBID-QX086, SBID-QX086-P, SBID-QX286, SBID-QX286-P; IDX75-4, SBID-MX075-V4, IDQX75-1, SBID-QX075, SBID-QX075-P, SBID-QX275, SBID-QX275-P; IDX65-4, SBID-MX065-V4, IDQX65-1, SBID-QX065, SBID-QX065-P, SBID-QX265, SBID-QX265-P; IDX55-4, SBID-MX055-V4 6. The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number in accordance with 15.212 (a)(1)(vi)(A) / (B). Yes, the Module will be label with its own FCC ID ,and the instruction on the labelling rule of the end product has been stated in the user manual of this module .please refer to the label and user manual exhibition. 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. For example, there are very strict operational and timing requirements that must be met before a transmitter is authorized for operation under Section 15.231. For instance, data transmission is prohibited, except for operation under Section 15.231(e), in which case there are separate field strength level and timing requirements. Compliance with these requirements must be assured. Yes, the required FCC rule has been fulfilled and all the instruction for maintaining compliance have been clearly stated in the user manual. 8. The modular transmitter must comply with any applicable RF exposure requirements. For example, FCC Rules in Sections 1.1310, 2.1091, 2.1093, and specific Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII and millimeter low power device. RF_734_02 04 April 16 wave devices perform routine environmental evaluation for RF Exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance. Modular transmitters approved under other Sections of Part 15, when necessary, may also need to address certain RF Exposure concerns, typically by providing specific installation and operating instructions for users, installers and other interested parties to ensure compliance. Note: A limited modular approval (LMA) may be granted for single modular transmitters that comply partially with the requirements above. Name and surname of applicant (or authorized representative): Nicole McMillan Signature: Date: 2022.12.9

Declaration on model difference We the undersigned hereby confirm that any of our production units bearing the following model numbers are identical in circuitry and electrical, mechanical and physical construction; the only differences are Host device size for each size， the model name and the color of appearance for trading purpose. FCC ID: QCI-IDNMOD1 Brand name Model no. SMART Board IDX86-4, SBID-MX086-V4, IDQX86-1, SBID-QX086, SBID-QX086-P, SBID- QX286, SBID-QX286-P; IDX75-4, SBID-MX075-V4, IDQX75-1, SBID-QX075, SBID-QX075-P, SBID- QX275, SBID-QX275-P; IDX65-4, SBID-MX065-V4, IDQX65-1, SBID-QX065, SBID-QX065-P, SBID- QX265, SBID-QX265-P; IDX55-4, SBID-MX055-V4 Confirmed by SMART Technologies ULC. Nicole McMillan SMART Technologies ULC. Date: 2022-12-24

SMART Technologies ULC 3636 Research Road NW Calgary, AB T2L 1Y1 CANADA Phone 403.245.0333 Fax 403.228.2500 [email protected] www.smarttech.com Federal Communications Commission 2022-10-20 Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Subject: FCC Application for FCC ID: QCI-IDNMOD1 To Whom It May Concern: We, the undersigned, hereby authorize Lisa Wang at EMTEK (SHENZHEN) CO., LTD. on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by EMTEK (SHENZHEN) CO., LTD. on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, Nicole McMillan / Manager, Systems Design, Regulatory and Compliance SMART Technologies Inc.

SMART Technologies ULC 3636 Research Road NW Calgary, AB T2L 1Y1 CANADA Phone 403.245.0333 Fax 403.228.2500 [email protected] www.smarttech.com Federal Communications Commission 2022-10-20 Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Subject: Request for Confidentiality FCC ID: QCI-IDNMOD1 To Whom It May Concern: Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, SMART Technologies is hereby requesting permanent confidentiality for the following exhibits: Block Diagram Operational Description Schematic Diagram Above mentioned documents contain detailed system and equipment descriptions which are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitors an unfair advantage in the market. Sincerely, Nicole McMillan / Manager, Systems Design, Regulatory and Compliance SMART Technologies Inc.

EUT EXTERNAL PHOTOGRAPHS Configuration A Configuration B ----------------The end----------------

FCC ID: QCI-IDNMOD1 IC ID: 4302A-IDNMOD1

TDRA REGISTERED No: DEALER No: Complies with IMDA Standards DB107329 Made in China IDQX65-1 LCD MONIT OR 100-240V~, 6.1-2.7A, 50/60Hz 10 0-240V~, 2.5-1.1A, 50/60Hz, 250W 103xxxx - 0x This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.. VARNING: APPARATEN SKALL ANSLUTAS TILL JORDAT UTTAG. ADVARSEL: APPARATET MÅ TILKOPLES JORDET STIKKONTAKT. VAROITUS: LAITE ON LIITETTÄVÄ SUOJAMAADOITUSKOSKETTIMILLA VARUSTETTUUN PISTORASIAAN. ADVARSEL: APPARATETS STIKPROP SKAL TILSLUTTES EN STIKKONTAKT MED JORD, SOM GIVER FORBINDELSE TIL STIKPROPPENS JORD I.T.E. 64RJ E364616 210-192431 R © 2022 SMART Technologies ULC. All rights reserved. SMART Board, the SMART logo and smarttech are trademarks or registered trademarks of SMART Technologies ULC in the U.S. and/or other countries. SMART Technologies ULC 3636 Research Road NW Calgary, AB T2L 1Y1, CANADA smarttech.com/support smarttech.com/compliance smarttech.com/patents USB3.0: 5V 0.9A Service 1: 5V 0.5A Service 2: 5V 0.9A 5V 0.9A 5V 0.9A USB-C 1: 5V 3A USB-C 2: 5V 3.0A / 9V 3.0A / 12V 3.0A 15V 3.0A / 20V 3.25A CAN ICES-003(A) / NMB-003(A) Contains IC: 24278-SKIWB921AU1, IC: 4302A-IDNMOD1, and IC: 4302A-IDQXMOD1 Contains FCC ID: 2AR82-SKIWB921AU1, FCC ID: QCI-IDNMOD1, and FCC ID:QCI-IDQXMOD1 R-NZ TDRA REGISTERED No: DEALER No: Complies with IMDA Standards DB107329 Made in China IDQX75-1 LCD MONIT OR 100-240V~, 6.3-2.7A, 50/60Hz 10 0-240V~, 2.5-1.1A, 50/60Hz, 250W 103xxxx -0x This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.. VARNING: APPARATEN SKALL ANSLUTAS TILL JORDAT UTTAG. ADVARSEL: APPARATET MÅ TILKOPLES JORDET STIKKONTAKT. VAROITUS: LAITE ON LIITETTÄVÄ SUOJAMAADOITUSKOSKETTIMILLA VARUSTETTUUN PISTORASIAAN. ADVARSEL: APPARATETS STIKPROP SKAL TILSLUTTES EN STIKKONTAKT MED JORD, SOM GIVER FORBINDELSE TIL STIKPROPPENS JORD I.T.E. 64RJ E364616 210-192431 R © 2022 SMART Technologies ULC. All rights reserved. SMART Board, the SMART logo and smarttech are trademarks or registered trademarks of SMART Technologies ULC in the U.S. and/or other countries. SMART Technologies ULC 3636 Research Road NW Calgary, AB T2L 1Y1, CANADA smarttech.com/support smarttech.com/compliance smarttech.com/patents USB3.0: 5V 0.9A Service 1: 5V 0.5A Service 2: 5V 0.9A 5V 0.9A 5V 0.9A USB-C 1: 5V 3A USB-C 2: 5V 3.0A / 9V 3.0A / 12V 3.0A 15V 3.0A / 20V 3.25A CAN ICES-003(A) / NMB-003(A) Contains IC: 24278-SKIWB921AU1, IC: 4302A-IDNMOD1, and IC: 4302A-IDQXMOD1 Contains FCC ID: 2AR82-SKIWB921AU1, FCC ID: QCI-IDNMOD1, and FCC ID:QCI-IDQXMOD1 R-NZ TDRA REGISTERED No: DEALER No: Complies with IMDA Standards DB107329 Made in China LCD MONIT OR IDQX86-1 100-240V~, 7.7-3.1A, 50/60Hz 10 0-240V~, 2.5-1.1A, 50/60Hz, 250W 103xxxx -0x I.T.E. 64RJ E364616 210-192431 R © 2022 SMART Technologies ULC. All rights reserved. SMART Board, the SMART logo and smarttech are trademarks or registered trademarks of SMART Technologies ULC in the U.S. and/or other countries. SMART Technologies ULC 3636 Research Road NW Calgary, AB T2L 1Y1, CANADA smarttech.com/support smarttech.com/compliance smarttech.com/patents This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.. VARNING: APPARATEN SKALL ANSLUTAS TILL JORDAT UTTAG. ADVARSEL: APPARATET MÅ TILKOPLES JORDET STIKKONTAKT. VAROITUS: LAITE ON LIITETTÄVÄ SUOJAMAADOITUSKOSKETTIMILLA VARUSTETTUUN PISTORASIAAN. ADVARSEL: APPARATETS STIKPROP SKAL TILSLUTTES EN STIKKONTAKT MED JORD, SOM GIVER FORBINDELSE TIL STIKPROPPENS JORD USB3.0: 5V 0.9A Service 1: 5V 0.5A Service 2: 5V 0.9A 5V 0.9A 5V 0.9A USB-C 1: 5V 3A USB-C 2: 5V 3.0A / 9V 3.0A / 12V 3.0A 15V 3.0A / 20V 3.25A CAN ICES-003(A) / NMB-003(A) Contains IC: 24278-SKIWB921AU1, IC: 4302A-IDNMOD1, and IC: 4302A-IDQXMOD1 Contains FCC ID: 2AR82-SKIWB921AU1, FCC ID: QCI-IDNMOD1, and FCC ID:QCI-IDQXMOD1 R-NZ 01 MP June 10, 2022 JT 02 MP Sept 14, 2022 PH USB3.0: 5V 0.9A Service 1: 5V 0.5A Service 2: 5V 0.9A 5V 0.9A 5V 0.9A USB-C 1: 5V 3A USB-C 2: 5V 3A / 9V 3A / 12V 3A / 15V 3A / 20V 3.25A SMART Technologies ULC. All rights reserved. SMART Board, the SMART logo and smarttech are trademarks or registered trademarks of SMART Technologies ULC in the U.S. and/or other countries. SMART Technologies ULC 3636 Research Road NW Calgary, AB T2L 1Y1, CANADA 1038833-02 IDX55-4 This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN. RISQUE D'ELECTROCUTION. NE PAS OUVRIR. CAN ICES-003 (A) / NMB-003 (A) Contains FCC ID: QCI-IDNMOD1 and FCC ID: 2AR82-SKIWB921AU1 Contains IC: 4302A-IDNMOD1 and IC: 24728-SKIWB921AU1 Input: 100-240V~, 4.0–1.75A, 50/60Hz I.T.E. 64RJ E364616 VARNING: APPARATEN SKALL ANSLUTAS TILL JORDAT UTTAG. ADVARSEL: APPARATET MÅ TILKOPLES JORDET STIKKONTAKT. VAROITUS: LAITE ON LIITETTÄVÄ SUOJAMAADOITUSKOSKETTIMILLA VARUSTETTUUN PISTORASIAAN. ADVARSEL: APPARATETS STIKPROP SKAL TILSLUTTES EN STIKKONTAKT MED JORD, SOM GIVER FORBINDELSE TIL STIKPROPPENS JORD USB3.0: 5V 0.9A Service 1: 5V 0.5A Service 2: 5V 0.9A 5V 0.9A 5V 0.9A USB-C 1: 5V 3A USB-C 2: 5V 3A / 9V 3A / 15V 3A / 20V 3.25A smarttech.com/support • smarttech.com/compliance • smarttech.com/patents USB3.0: 5V 0.9A Service 1: 5V 0.5A Service 2: 5V 0.9A 5V 0.…

Text truncated - open the document above for the full version.

TDRA REGISTERED No: DEALER No: Complies with IMDA Standards DB107329 Made in China LCD MONITOR SBID-QX086 100-240V~, 7.7-3.1A, 50/60Hz 100- 240V~, 2.5-1.1A, 50/60Hz, 250W 103xxxx -0x …

Text truncated - open the document above for the full version.