QCIWC6DBluetooth Dongle

~ ~ ~ ~ 4 www.smarttech.com/Support/SB6/FirmwareUpdate 1 3 2 #2 WC6D Wireless Bluetooth® Connection <2 min + 5 sec5 sec 5 www.smarttech.com/support www.smarttech.com/contactsupport Support +1.403.228.5940 or Toll Free 1.866.518.6791 (U.S./Canada) 99-01045-20 REV A0 *99-01045-20-A0* Hardware Environmental Compliance SMART Technologies supports global efforts to ensure that electronic equipment is manufactured, sold and disposed of in a safe and environmentally friendly manner. Waste Electrical and Electronic Equipment Regulations (WEEE Directive) Waste Electrical and Electronic Equipment regulations apply to all electrical and electronic equipment sold within the European Union. When you dispose of any electrical or electronic equipment, including SMART Technologies products, we strongly encourage you to properly recycle the electronic product when it has reached end of its life. If you require further information, please contact your reseller or SMART Technologies for information on which recycling agency to contact. Packaging Many countries have regulations restricting the use of certain heavy metals in product packaging. The packaging used by SMART Technologies to ship products complies with packaging laws. U.S. Consumer Product Safety Improvement Act The United States has enacted the Consumer Product Safety Improvement Act which limits the lead (Pb) content in products. SMART Technologies is committed to complying with this initiative. © 2009-2010 SMART Technologies ULC. All rights reserved. The SMART logo and smarttech are trademarks or registered trademarks of SMART Technologies ULC in the U.S. and/or other countries. All other third-party product and company names may be trademarks of their respective owners. Contents are subject to change without notice. 03/2010. FCC Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. You can determine whether the equipment is causing interference by disconnecting it from your computer. If the interference stops, it was probably caused by the equipment. If the equipment does cause interference to radio or television reception, you may be able to correct the interference by using one or more of the following measures: • Rotate the television or radio antenna until the interference stops. • Move the equipment farther away from the television or radio. • Plug the equipment and computer into an outlet that is on a different circuit from the television or radio. If necessary, consult SMART Technologies ULC or an experienced radio/ television technician for help. Changes or modifi cations to this product not authorized by SMART Technologies ULC could void the FCC Certifi cation and negate your authority to operate the product.

SMART Technologies ULC Page 1 of 73 FCCID: QCIWC6D ICID: 4302A-WC6D Reference No.: 150932 FCC/IC Test Report FCC EVALUATION REPORT FOR VERIFICATION Project Reference No. 150932 Product Bluetooth Dongle Brand Name Model WC6D-D01 Alternate Model N/A Tested according to FCC Rules and Regulations Part 15 Subpart C 2008 15.247, RSS-210 issue 7 ANSI C63.4-2009 Tested in period 2010-06-01 to 2010-07-22 Issued date 2010-07-30 Name and address of the Test House Nemko Shanghai Ltd. 9A No. 528 Ruiqing Road, PuDong New Area, Shanghai, China P.C. Phone : +86 21 5072 0988 Fax : +86 21 5072 0950 Tested by 2010-07-30 Zone Peng date Verified by 2010-07-30 Daria Liu date This form is only for use by Nemko, or by others according to special agreement with Nemko. The report may be reproduced infull. Partial reproduction may only be made with the written content of Nemko Shanghai. This report applies only to the sample(s) tested. It is the manufacturer’s responsibility to assure the additional production units of this product are manufactured with identical electrical and mechanical components. SMART Technologies ULC Page 2 of 73 FCCID: QCIWC6D ICID: 4302A-WC6D Reference No.: 150932 Contents of This Report 1. Client Information ............................................................................................................................... 5 1.1 Applicant .................................................................................................................................... 5 1.2 Manufacturer .............................................................................................................................. 5 1.3 Scope ......................................................................................................................................... 5 2. Equipment under Test (EUT) .............................................................................................................. 6 2.1 Identification of EUT .................................................................................................................. 6 2.2 Detail spec ................................................................................................................................. 6 2.3 Additional Information Related to Testing .................................................................................. 6 2.4 Picture Documentation .............................................................................................................. 6 3. General Test Conditions ...................................................................................................................... 7 3.1 Location ..................................................................................................................................... 7 3.2 Operating Environment .............................................................................................................. 7 3.3 Operating During Test ................................................................................................................ 7 3.4 Test Equipment .......................................................................................................................... 7 4. Measurement Uncertainty ................................................................................................................... 8 5. Radiated Electromagnetic Disturbances ............................................................................................. 9 5.1 Test Procedure ........................................................................................................................... 9 5.2 Measurement Equipment ........................................................................................................... 9 5.3 Test Result ............................................................................................................................... 10 5.3.1 Diagram 5-1 ................................................................................................................................. 12 5.3.1 Diagram 5-1 ................................................................................................................................. 12 5.3.2 Diagram 5-2 ................................................................................................................................. 13 5.3.3 Diagram 5-3 ................................................................................................................................. 14 5.3.8 Diagram 5-8 ................................................................................................................................. 19 5.3.9 Diagram 5-9 ................................................................................................................................. 20 5.3.10 Diagram 5-10 ............................................................................................................................. 20 5.3.11 Diagram 5-11 .............................................................................................................................. 21 5.3.12 Diagram 5-12 ............................................................................................................................. 21 5.3.13 Diagram 5-13 ............................................................................................................................. 22 5.3.14 Diagram 5-14 ............................................................................................................................. 22 5.3.15 Diagram 5-15 ............................................................................................................................. 23 5.3.16 Diagram 5-16 ............................................................................................................................. 24 5.3.17 Diagram 5-17 .............................................................................................…

Text truncated - open the document above for the full version.