QD8NB-3Electronic Scales

FCC ID : QD8NB-3 REPORT NO. : HCT-F03-1104 HYUNDAI C–TECH 1/27 AT TA CH MEN T E. - USER’S MANUAL - FCC ID : QD8NB-3 REPORT NO. : HCT-F03-1104 HYUNDAI C–TECH 2/27 nBody-DP Instructions Manual FCC ID : QD8NB-3 REPORT NO. : HCT-F03-1104 HYUNDAI C–TECH 3/27 Copyright  2002 CAS. All rights reserved. This manual and the software described herein, in whole or in part, may not be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form without prior written approval by CAS. The products of CAS operate a policy of continuous changes and improvements. Therefore, we reserve the right to make modifications and changes to this manual without prior notice. CAS is not responsible for any loss of data or for any incidental, or consequential damage howsoever caused. CAS and nBody-DP are registered trademarks of CAS Corporation. All other trademarks are trademarks of their respective owners. FCC ID : QD8NB-3 REPORT NO. : HCT-F03-1104 HYUNDAI C–TECH 4/27 Powerful nBody-DP! Now it is easier to control nBody-DP with Dual display (Easy nBody-DP with Dual Display) nbody-DP has upgraded from previous PC connectable nBody. Without computer display, nBody-DP scale itself has display attached to it so without connecting the nBody-DP with computer, it can be used by itself displaying weight. * When Sole Use 9 50g interval measuring precision scale 9 Automatic measured weight save up to 100 times 9 Bright LED 9 Simple steps to transfer measured data to PC * When connected with PC 9 PC connection using USB cable 9 user setup up to 10 different person 9 Diplay charts for weight, body fat, BMI fatness and data save. 9 synthesized body measurement result and printing fucntion „ Special Feature ① nBody-DP sole use or PC connection use ② Easy to see red LED and PC display (dual display) ③ Weight memory up to 100 times when sole use ④ Easy data transfer when connected with PC ⑤ Personal Database up to 10 different people using single nBody-DP ⑥ Power generated by PC USB Cable (when connected with PC) FCC ID : QD8NB-3 REPORT NO. : HCT-F03-1104 HYUNDAI C–TECH 5/27 Precautions before using nBody-DP 1. Install nBody DP-measuring device on a flat, stable surface that is free of vibration. 2. In case your hands or feet are wet after connecting nBody-DP measuring device to your computer, do not touch other electric appliances or stand on the device. As in any electronic device, there is a danger of being struck by electricity. 3. The cable connected to the nBody-DP measuring device is detachable. Therefore, it is dangerous to lift the device holding the cable only. When moving nBody-DP measuring device, make sure you hold the main body of device. 4. Do not insert or extract the cable of nBody-DP measuring device unnecessarily. It can cause trouble to the cable connector. 5. It is important that your computer is using a safe multi-outlet to prevent electric shock in case of electric leakage. 6. Do not install nBody-DP in the area with high magnetism and electric wave. Unstable AC power could be the cause of error. Precautions while measuring 1. Make sure that the nBody-DP measuring device is installed on a flat, stable surface that is free of vibration. 2. Do not attempt to weigh exceeding the maximum weight on nBody-DP measuring device. 3. Do not shock or apply excessive force to nBody-DP measuring device physically. Avoid tumbling of objects. FCC ID : QD8NB-3 REPORT NO. : HCT-F03-1104 HYUNDAI C–TECH 6/27 4. Do not leap onto or jump on top of nBody-DP measuring device. There is a possibility of causing serious injury if you lose balance. Care and Maintenance 1. Use a soft piece of cloth to clean nBody-DP measuring device. Avoid soaking the interior of the device. 2. Do not expose the device to extreme heat. It may damage the device and cause fire. 3. Do not make any changes or modifications to the equipment unless otherwise specified in the Instructions Manual. If such changes or modifications should be made, you could be required to stop operation of the equipment. 4. Repairs to certified equipment should be made by an authorized maintenance facility designated by the supplier. If you need a repair, please inquire at your nearest CAS dealer or nBody-DP business office. Do not attempt to repair nBody-DP. There is a possibility of electric shock or other injuries and furthermore, the nBody-DP will not be responsible for warranty. FCC ID : QD8NB-3 REPORT NO. : HCT-F03-1104 HYUNDAI C–TECH 7/27 Ta b l e o f C o n t e n t s Preparations 1. Making sure everything is in the box 2. Names and functions of nBody-DP measuring device 3. Installation of nBody-DP measuring device 4. Installation of nBody-DP client program 5. Names and functions of nBody-DP client main screen Operations and Usage 1. Running nBody-DP client and skin modifications 2. Measuring your weight 3. User registration 4. Measuring modes 5. Data functions and management 6. Health Information administration 7. Additional operations System requirements Basic specifications Regulatory information  Appendix EveryBody nBody-DP! Customer service contacts FCC ID : QD8NB-3 REPORT NO. : HCT-F03-1104 HYUNDAI C–TECH 8/27 Preparations 1. Making sure everything is in the box Check to make sure you have everything that’s shown and listed below. If you find any items to be missing, please inquire at the store you made the purchase. 9 One nBody-DP measuring device 9 One nBody-DP client software CD 9 One USB cable 9 One nBody-DP measuring tape 9 One height measuring sheet 9 Two sets of Color wings 9 One nBody-DP manual 9 One product installation easy guide 2. Names and functions of Parts of nBody-DP measuring device  Measuring weight section  RED LED  USB port : Port that connects USB cable with nBody-DP measuring device.  USB cable : Cable that connect nBody-DP measuring device with computer. (Exclusive use of cable required) ①Measuring weight section ② LED Display ③USB port ④USB cable FCC ID : QD8NB-3 REPORT NO. : HCT-F03-1104 …

Text truncated - open the document above for the full version.

FCC ID: QD8NB-3 REPORT NO. : HCT-F03-1104 HYUNDAI C–TECH 1/5 ATTACHMENT C. - BLOCK DIAGRAM(S) - FCC ID: QD8NB-3 REPORT NO. : HCT-F03-1104 HYUNDAI C–TECH 2/5 nBody-DP FCC ID: QD8NB-3 REPORT NO. : HCT-F03-1104 HYUNDAI C–TECH 3/5 FCC ID: QD8NB-3 REPORT NO. : HCT-F03-1104 HYUNDAI C–TECH 4/5 FCC ID: QD8NB-3 REPORT NO. : HCT-F03-1104 HYUNDAI C–TECH 5/5

FCC ID : QD8NB-3 REPORT NO. : HCT-F03-1104 HYUNDAI C–TECH 1/5 AT TA CH MEN T B. - EXTERNAL PHOTOS - FCC ID : QD8NB-3 REPORT NO. : HCT-F03-1104 HYUNDAI C–TECH 2/5 FCC ID : QD8NB-3 REPORT NO. : HCT-F03-1104 HYUNDAI C–TECH 3/5 FCC ID : QD8NB-3 REPORT NO. : HCT-F03-1104 HYUNDAI C–TECH 4/5 FCC ID : QD8NB-3 REPORT NO. : HCT-F03-1104 HYUNDAI C–TECH 5/5

FCC ID : QD8NB-3 REPORT NO. : HCT-F03-1104 HYUNDAI C–TECH 1/3 ATTACHMENT A. - ID LABEL INFORMATION AND LOCATION PHOTOS - FCC ID : QD8NB-3 REPORT NO. : HCT-F03-1104 HYUNDAI C–TECH 2/3 1.1 ID Label Information Following is a copy of the label that will be placed on the rear side of the cabinet. Figure 3.1 PRODUCT LABEL Both the FCC ID and compliance statement are included in the product label FCC ID : QD8NB-3 REPORT NO. : HCT-F03-1104 HYUNDAI C–TECH 3/3 1.2 Label Location Photos The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase.(Labeling requirements per 2.925)

FCC ID : QD8NB-3 REPORT NO. : HCT-F03-1104 HYUNDAI C–TECH 1/10 ATTA CHMEN T F. - INTERNAL PHOTOS - FCC ID : QD8NB-3 REPORT NO. : HCT-F03-1104 HYUNDAI C–TECH 2/10 FCC ID : QD8NB-3 REPORT NO. : HCT-F03-1104 HYUNDAI C–TECH 3/10 FCC ID : QD8NB-3 REPORT NO. : HCT-F03-1104 HYUNDAI C–TECH 4/10 FCC ID : QD8NB-3 REPORT NO. : HCT-F03-1104 HYUNDAI C–TECH 5/10 FCC ID : QD8NB-3 REPORT NO. : HCT-F03-1104 HYUNDAI C–TECH 6/10 FCC ID : QD8NB-3 REPORT NO. : HCT-F03-1104 HYUNDAI C–TECH 7/10 FCC ID : QD8NB-3 REPORT NO. : HCT-F03-1104 HYUNDAI C–TECH 8/10 FCC ID : QD8NB-3 REPORT NO. : HCT-F03-1104 HYUNDAI C–TECH 9/10 FCC ID : QD8NB-3 REPORT NO. : HCT-F03-1104 HYUNDAI C–TECH 10/10

HYUNDAI CALIBRATION & CERTIFICATION TECH. CO., LTD. Product Compliance Division, EMC Team SAN 136-1, AMI-RI , BUBAL-EUP, ICHEON-SI, KYOUNKI-DO, 467-701, KOREA TEL : +82 31 639 8518 FAX : +82 31 639 8525 CERTIFICATION Rule Part(s): Equipment Class: Standard(s): EUT Type: Model(s): Port/Connector(s) This equipment has been shown to be in compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in ANSI C63.4-1992 (Grant Notes: #19, #28). I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. Report prepared by : Ki-Soo Kim Manager of EMC Tech. Part ▷▷ HYUNDAI CALIBRATION & CERTIFICATION TECH. CO., LTD. ◁◁◁ 1/ 19 QD8NB-3 nBody-DP/ Scales Manufacture; CAS Corporation. #19 Ganap-ri Gwangjuk-Myoun Yangju-gun Gyeonggi-do, Seoul Korea CAS FRN : 0007-1276-16 Date of Issue : NOVEMBER 13, 2003 Test Report No.: HCT-F03-1104 Test Site: HYUNDAI CALIBRATION & CERTIFICATION TECHNOLOGIES CO., LTD. HCT FRN : 0005-8664-21 FCC ID : MODEL / TYPE : Part 15 & 2 FCC Class B Peripheral Device (JBP) FCC Class B: 2001 (CISPR 22:1998) Scales nBody-DP USB Port FCC ID : QD8NB-3 REPORT NO. : HCT-F3-1104 HYUNDAI C–TECH 2/19 TABLE OF CONTENTS PAGE REPORT COVER 1 TABLE OF CONTENTS 2 1.1 SCOPE 3 2.1 INTRODUCTION (SITE DESCRIPTION) 4 3.1 PRODUCTION INFORMATION 5 4.1 DESCRIPTION OF TESTS (CONDUCTED) 6 4.2 DESCRIPTION OF TESTS (RADIATED) 7 5.1 LIST OF SUPPORT EQUIPMENT 8-9 6.1 TEST DATA (CONDUCTED) 10-14 7.1 TEST DATA (RADIATED) 15 8.1 SMPLE CALCULATIONS 16 9.1 TEST EQUIPMENT 17 10.1 TEST SOFTWARE USED 18 11.1 CONCLUSION 19 ATTACHMENT A: FCC ID LABEL & LOCATION ATTACHMENT B: EXTERNAL PHOTOGRAPHS ATTACHMENT C: BLOCK DIAGRAM(S) ATTACHMENT D: TEST SETUP PHOTOGRAPHS ATTACHMENT E: USER’S MANUAL ATTACHMENT F: INTERNAL PHOTOGRAPHS FCC ID : QD8NB-3 REPORT NO. : HCT-F3-1104 HYUNDAI C–TECH 3/19 MEASUREMENT REPORT 1.1 SCOPE Measurement and determination of electromagnetic emissions (EME) of radio frequency devices including intentional and/or unintentional radiators for compliance with the technical rules and regulations of the Federal Communications Commission. • FCC ID : QD8NB-3 • Equipment Class: FCC Class B Peripheral Device (JBP) • EUT Type: Scales • Model(s): nBody-DP • Cable(s): Unshielded • Rule Part(s): FCC Part 15 Subpart B • Test Procedure(s): ANSI C63.4 (1992) • Dates of Tests: NOVEMBER 1, 2003 ~ NOVEMBER 5, 2003 • Place of Tests: 254-1,MAEKOK-RI,HOBUP-MYUN,ICHON-SI,KYOUNGKI-DO,467-701,KOREA Applicant Name: Address: CAS Corporation #19 ganap-ri Gwangjuk-Myoun Yangju-gun Gyeonggi-do, Seoul Korea FCC ID : QD8NB-3 REPORT NO. : HCT-F3-1104 HYUNDAI C–TECH 4/19 2.1 INTRODUCTION The measurement procedure described in American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9kHz to 40GHz (ANSIC63.4-1992) was used in determining radiated and conducted emissions emanating from CAS Corporation. Scales FCC ID: QD8NB-3 The open area test site and conducted measurement facility used to collect the radiated data are located at the 254-1, MAEKOK-RI,HOBUP-MYUN,ICHON-SI,KYOUNGKI-DO, 467-701,KOREA. The site is constructed in conformance with the requirements of ANSI C63.4and CISPR Publication 22. Detailed description of test facility was submitted to the Commission and accepted dated July 24,2000 (Confirmation Number: EA90661) FCC ID : QD8NB-3 REPORT NO. : HCT-F3-1104 HYUNDAI C–TECH 5/19 3.1 PRODUCT INFORMATION (Equipment Description) Equipment Under Test (EUT) is the CAS Corporation. ( Model : nBody-DP) Scales FCC ID : QD8NB-3 Port(s)/Input Connector(s): USB Port Cable(s): Unshielded Dimensions (W×H×D): 260x228x54mm(W×H×D) Weight (Net):3.4Kg Power Used : USB POWER or AAA Battery (1.5V)x4 FCC ID : QD8NB-3 REPORT NO. : HCT-F3-1104 HYUNDAI C–TECH 6/19 4.1 Description of Tests(Conducted) (Power line Conducted RFI (150kHz- 30MHz) ) The power line conducted RFI measurements were performed according to CISPR 22. The EUT was placed on a non-conducting 1.0 by 1.5 meter table which is 0.8 meters in height and 0.40 meters away from the vertical wall of the shielded enclosure. Power to the EUT is provided through a Rohde & Schwarz 50 Ω / 50 uH Line Impedance Stabilization Network (LISN) and the support equipment through a separate Solar 50 Ω / 50 uH Line- Conducted Test Facility LISN. Sufficient time for the EUT, support equipment, and test equipment were allowed in order for them to warm up to their normal operating condition. The RF output of the LISN was connected to the spectrum analyzer to determine the frequency producing the maximum EME. The spectrum was scanned from 150kHz to 30 MHz. Each maximum EME was measured using an EMI receiver. The detector function of the receiver was set to CISPR quasi- peak and average mode with the bandwidth set to 9 kHz. Each emission was maximized consistent with the typical applications by varying the configuration of the test sample. Interface cables were connected to the available interface ports of the test unit. The effect of varying the position of cables was investigated to find the configuration that produces maximum Diagram emission. Excess cable lengths were bundled at the centre with 30- 40cm. in length. The worst-case configuration is noted in the test report and the photographs are attached. Each EME reported was calibrated using the Rohde & Schwarz SMX signal generator and are listed on Table 1. RFI Conducted FCC Class B RFI CONDUCTED FCC CLASS B Limits dB(uV/m) CISPR 22 CLASS B Limits dB(uV/m) Freq. Range FCC Class B Quasi-Peak CISPR 22 Quasi-Peak CISPR 22 Average 150kHz - 0.5MHz 48* 66-56** 56-46** 0.5MHz - 5MHz 48 56 46 5MHz - 30MHz 48 60 50 *FCC Class B li…

Text truncated - open the document above for the full version.

FCC ID : QD8NB-3 REPORT NO. : HCT-F03-1104 HYUNDAI C–TECH 1/4 ATTACHMENT D. - TEST SETUP PHOTOS- FCC ID : QD8NB-3 REPORT NO. : HCT-F03-1104 HYUNDAI C–TECH 2/4 1.CONDUCTED AND RADIATED MEASUREMENT PHOTOS [CONDUCTED MEASUREMENT PHOTO] FCC ID : QD8NB-3 REPORT NO. : HCT-F03-1104 HYUNDAI C–TECH 3/4 [RADIATED MEASUREMENT PHOTO] FCC ID : QD8NB-3 REPORT NO. : HCT-F03-1104 HYUNDAI C–TECH 4/4