QE850XXXTX27RC HELICOPTER

Item# 50400 Congratulations on your purchase of the HELICOPTER 1 x HELICOPTER 1 x CONTROLLER 1 x USB CHARGING WIRE Do not modify your Helicopter! Any changes or modifications to this product are strictly prohibited and will void product warra nty. Do not attempt to charge the Helicopter from any other source other than the USB charging wire provided to charge the Lithium Polymer Battery or you will void the warranty! Any attempts at charging other products with the USB charging wire are strictly prohibited and will void the warranty! The Lithium Polymer Battery is permanently built-in to the Helicopter. Any attempts to t amper with or remove the Lithium Polymer Battery inside the Helicopter is stictly prohibited and will void the warranty. Do not point the Antenna directly at the Helicopter! Do not use in strong winds, use only in VERY mild conditions! Do not use in rain, snow or a round heavy debris! Do not use near electrical lines or high voltage wires or other sources of electricity! Do not use around smoke o r flames! Do not use around water and other liquids! Do not use in crowded areas! Do not use around air conditioning! Do not use around a ir vents! Do not use around ceiling fans! Do not use around large obstacles! Do not use in very small spaces! Do be conscious of changes in your area! Keep moving Rotors and Propellers away from eyes, hands, hair and loose clothing. Always turn off your Helicopter and Controlle r when not in use. Always remove the batteries from the Controller during storage. Always use new and fresh Alkaline Batteries in Cont roller for optimal performance. Battery performance will greatly influence flight characteristics. Keep your Instruction Manual in a safe place for future reference. Parental supervision required. The Controller takes one 9V battery (Not included). This radiocommunication device complies with all the requirements of the Industry Canada Standard RSS-310. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. Field Strength and measurement distance: 27.145MHz - 61.35 dBuV/m at 3 meter. 49.860 MHz - 59.00 dBuV/m at 3 meter. Industry Canada Notice: Canada only. Manufactured by and distributed by Interactive Toy Concepts Ltd. INS-50400-100318-US This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may no t cause harmful interference. 2) This device must accept any interference received including interfer ence that may cause undesired operation. Warning: Changes or mod ifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to oper ate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These L imits are designed to provide reasonable protection against harmful interference in a residential installation. This generates, uses and can radiate radio frequency ene rgy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communic ations. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equi pment off and on, the user is encouraged to try and correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna - Incre ase the separation between the equipment and receiver - Connect the equipment to an outlet on a circuit different from that to which the receiver is connected - Consult the dealer or an experienced radio/TV technician for help. 1. Slide to open the battery compartment door. 2. Insert the 1 x 9V battery according tothe picture shown. Ensure that the + and - polarities match the illustrationsinside the battery compartment. 3. Replace the battery compartment door. CHARGING THE HELICOPTER Before flying the Helicopter for the first time or if you have depleted the charge, you willneed to recharge it. A typical charge takes about 30-60 minutes and allows for approximately 4-6 minutesof flying time.MAKE SURE THE HELICOPTER IS TURNED OFF BEFORE THE RECHARGING CYCLE IS COMMENCED.Note: During charging, both the RED LED on helicopter will light up. The LED will extinguish completelywhen the charge is complete.1) Ensure the Helicopter is turned off. When the helicopter turn off, the front LED turned off.2) Insert the USB charging wire into any USB power source as shown. Make sure the USB source has power on.3) Insert the USB charging wire into the Helicopter charging port which located on the right side of the Helicopter.4) The charging LED of Helicopter turn on. The Helicopter is charging. It takes 30-60 minutes to finish the charging.5) When the charging LED turn off, the charging is completed.6) Gently remove the charging wire from the Helicopter. ON/OFF LED MODE SWITCH FORWARD/BACKWARDDIRECTIONAL CONTROL Insert the USB charging wire into any USB power source. USB charging port in the Helicopter. Insert the USB charging wire the USB charging port in the Helicopter. 1. Turn the controller on by press the ON/OFF Button. The ON/OFF LED will light up.2. Turn on the Helicopter on by slide ON/OFF switch located at the left side of the Helicopter as shown. The front LED will lig ht up. 3. Place the Helicopter on a flat level surface for launch.4. On the controller, push the left stick all the way up once, and bring it back down completely to activate the control.5. Push the left stick up again to activa…

Text truncated - open the document above for the full version.

27.145MHz BlockDiagram

Interactive Toy Concepts (HK) Ltd. FCC ID: QE850XXXTX27 POWER OF ATTORNEY March 22,2010 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern: We, the undersigned, hereby authorize Waltek Services (ShenZhen) Co., Ltd. (Philo Zhong) on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Waltek Services (ShenZhen) Co., Ltd. (Philo Zhong) on our behalf shall have the same effect as acts of our own. This authorization expires on March 23,2010. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. We, Interactive Toy Concepts (HK) Ltd., are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, Interactive Toy Concepts (HK) Ltd. ------------------------------- General Manager

Interactive Toy Concepts (HK) Ltd. FCC ID: QE850XXXTX27 Ref No.: WT10030774-E-E-F Page 23 of 25 11 Photographs - Constructional Details 11.1 EUT – Front View 11.2 EUT – Back View

Interactive Toy Concepts (HK) Ltd. FCC ID: QE850XXXTX27 Ref No.: WT10030774-E-E-F Page 25 of 25 12 FCC ID Label This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The Label must not be a stick-on paper. The Label on these products must be permanently affixed to the product and readily visible at the time of purchase and must last the expected lifetime of the equipment not be readily detachable. Proposed Label Location on EUT EUT Bottom View/proposed FCC Label Location FCC ID: QE850XXXTX27 This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:1. This device may not cause harmful interference, and 2. This device must accept any interference received,including interference that may cause undesired operation .

FCC ID Label Sample for Model: RC Helicopter FCC ID : QE850XXXTX27 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Interactive Toy Concepts (HK) Ltd. FCC ID: QE850XXXTX27 Ref No.: WT10030774-E-E-F Page 24 of 25 11.3 PCB – Front View 11.4 PCB – Back View

Circuit Description When the control key is pressed,A encode signal from U4 is transmitted.Q6 and crystal for osilator,Q1 is rf amp ,Q2 is modulation encode signal for rf, signal through filter send by antenna.Antenna and grond circuitryThis unit make use an extenal antenna，This antenna is inductively coupled.This unit relies on the ground trace of the printed circuit board.No external ground is provided.energry is supplied by 6pcs aa alkaline battery.the user turning on the unit to the toy game when turned on,The unit comes up on the default channel and transmits a continuously steam data.The user can not change .Change to any other of the predefined chann el.The transmitted rf circutiry consists of a crystal controlled oscillator,which is 27.145Mhz.A 27.145MHZ crystal oscillator is used to generate ths reference frequencyIt has a stability of +/-20ppm.Ths Oscillator is followed by amplifiers.These final output is 80dbuv/m max .The tx system iscontrolled by a encode ic running with 16mhz rc

50400 TX(27M).sch-1 - Wed Mar 10 08:38:02 2010 Interactive Toy Concepts (HK) Ltd. 页码： 公司名称：项目名称：绘图： 审核： 编号： 版本：日期： 50400 TX (27M) 309010 前后 左右 微调 主马达 1/1 页 27MHz ADD Huang QUICK/SLOW LED SW Red + + Q6 2SC2712 Q1 2SC1815Y R10 220 R7 1K Z1 27.145MHZ L2 3.3UH T1 1.8uH C2 47P C9 24P L1 5.6uH ANT Q7 S8050 R16 330R C10 104 Q2 8550S R17 5.6K R18 1K L31UH C8 68P R8 12K C7 150P C13 391 C12 222 C4 68P R14 6.8K R15 3.9K LED R5 680R SW1 NC 104 1 P2.2 2 P2.1 3 P2.0 4 VDD 5 P1.3/XIN 6 P1.2/XOUT 7 P1.1/RST/VPP 8 P5.4 9 P1.0 10 P0.0/INT0 11 VSS 12 P2.5 13 P2.4 14 P2.3 U4 SN8P2501_14 C1 104 VR3 5K R25.1K/+-1% C5 100UF C3 104 C14 100UF 1 1 2 2 3 3 U1 ML62502TB B1 VR2 5K VR1 5K C11 47P R4 33K R3 10K 1 2 3 4 SW2 2 1 3 SW1 C02 105 R9 47R R1110K GND +9V GND GND +5V GND GND GND GND GND GND GND +9V +9V GND GND +5V +5V GND

Interactive Toy Concepts (HK) Ltd. FCC ID: QE850XXXTX27 FCC TEST REPORT Page 1 of 25 Ref No.: WT10030774-E-E-F FCC ID : QE850XXXTX27 Applicant : Interactive Toy Concepts (HK) Ltd. Address of Applicant:7/F., Eu Yan Sang Tower, 11-15 Chatham Road South, Tsim Sha Tsui, Kowloon, Hong Kong Equipment Under Test (EUT) : Product description : RC Helicopter Model No. : RC Helicopter Standards : FCC 15 Subpart C Paragraph 15.227 Date of Test : March 22,2010 Test Engineer :Olic huang Reviewed By : PERPARED BY: Waltek Services (Shenzhen) Co., Ltd. 1/F, Fukangtai Building,West Baima Rd.,Songgang Street, Baoan District, Shenzhen 518105,China Tel: +86-755-27553488 Fax: +86-755-27553686 Interactive Toy Concepts (HK) Ltd. FCC ID: QE850XXXTX27 Page 2 of 25 Ref No.: WT10030774-E-E-F 2 Contents Page 1 COVER PAGE..........................................................................................................................................................1 2 CONTENTS ..............................................................................................................................................................2 3 TEST SUMMARY....................................................................................................................................................4 4 GENERAL INFORMATION..................................................................................................................................5 4.1 CLIENT INFORMATIO...............................................................................................................................................5 4.2 GENERAL DESCRIPTION OF E.U.T...........................................................................................................................5 4.3 DETAILS OF E.U.T. .................................................................................................................................................5 4.4 DESCRIPTION OF SUPPORT UNITS...........................................................................................................................5 4.5 STANDARDS APPLICABLE FOR TESTING..................................................................................................................5 4.6 TEST FACILITY........................................................................................................................................................6 4.7 TEST LOCATION......................................................................................................................................................6 5 EQUIPMENT USED DURING TEST ...................................................................................................................7 6 CONDUCTED EMISSION TEST ........................................................................................................................10 6.1 TEST EQUIPMENT..................................................................................................................................................10 6.2 TEST PROCEDURE.................................................................................................................................................10 6.3 CONDUCTED TEST SETUP.....................................................................................................................................11 6.4 EUT OPERATING CONDITION...............................................................................................................................11 6.5 CONDUCTED EMISSION LIMITS.............................................................................................................................12 6.6 CONDUCTED EMISSION TEST RESULT...................................................................................................................12 7 RADIATION EMISSION TEST...........................................................................................................................13 7.1 TEST EQUIPMENT..................................................................................................................................................13 7.2 MEASUREMENT UNCERTAINTY.............................................................................................................................13 7.3 TEST PROCEDURE.................................................................................................................................................14 7.4 RADIATED TEST SETUP.........................................................................................................................................14 7.5 SPECTRUM ANALYZER SETUP...............................................................................................................................15 7.6 CORRECTED AMPLITUDE & MARGIN CALCULATION............................................................................................16 7.7 SUMMARY OF TEST RESULTS................................................................................................................................16 7.8 EUT OPERATING CONDITION...............................................................................................................................17 7.9 RADIATED EMISSIONS LIMIT.................................................................................................................................17 7.10 RADIATED EMISSIONS TEST RESULT................................................................................................................18 7.11 RADIATED EMISSION TEST DATA.....................................................................................................................19 8 ANTENNA REQUIREMENT...............................................................................................................................20 9 OCCUPIED BANDWIDTH ...............................................................................................................…

Text truncated - open the document above for the full version.

Interactive Toy Concepts (HK) Ltd. FCC ID: QE850XXXTX27 Ref No.: WT10030774-E-E-F Page 22 of 25 10 Photographs of Testing Radiation Emission Test Setup View