QHC-KVEVZE41kV2c-AMPZE Module

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Certification Exhibit FCC ID: QHC-KVEVZE41 FCC Rule Part: 15.247 ACS Project Number: 14-0144 Manufacturer: Itron Model: 570974-001 Manual kV2c-AMPZE User Information Manual kV2c-AMPZE User Information Manual Itron Model 570974-001 kV2c-AMPZE User Information Manual Labeling The following requirements will be applied to any products that use this module: The end product label will include the following text: Contains: FCC ID: QHC-KVEVZE41 Model: 570974-001 The user’s manual for any product that contains this module will contain the following test. If the device is large enough, this information will also placed on the label: “THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS. (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.” Regulatory Compliance The user’s manual for any product that contains this module will contain the following text: FCC Part 15, Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. kV2c-AMPZE User Information Manual RF Exposure The antennas used for this transmitter must be installed to provide a minimum separation distance of 20 cm from all persons, and must not be co-located or operate in conjunction with any other antenna or transmitter. End users and installers must be provided with antenna installation procedures and transmitter operating conditions for satisfying RF exposure compliance. Miscellaneous The user’s manual for any product that contains this module will contain the following text: Professional Installation This module is intended for professional installation by the integrator. The OEM integrator is still responsible for the FCC compliance requirement of the end product which uses this module. Modification and Repairs To ensure FCC compliance and system performance, this device, antenna and/or coaxial assembly shall not be changed or modified without the express written approval of Itron. Any unauthorized modification will void the user’s authority to operate the equipment. WARNING! This device contains no user serviceable parts. Attempts to repair this device by unauthorized personnel may subject the person to shock hazard if removal of protective covers is attempted. Unauthorized repair will void the warranty and/or any maintenance contract with your company. General Description The Itron 570974-001 (kV2c-AMPZE) is an electricity metering module which includes a Cellular EVDO WAN module operating in the GSM 800 MHz and PCS 1900 MHz bands,a HAN transmitter operating in the 2.4 GHz band, and a LAN transmitter operating in the 900MHz ISM band. The module operates on direct current which is supplied by the host meter device. kV2c-AMPZE User Information Manual ANTENNAS WAN Antenna: Under Glass Ribbon Gain: +0 dBi 800 & 1900 band PASSBAND: 824-894 Cellular Band & 1850-1990 PCS Band External Mono-Pole Gain : +3dBi 800 band +4dBi 1900 band PASSBAND: 824-894 Cellular Band & 1850-1990 PCS Band HAN Antenna: PCB antenna embedded in the module: GAIN: +3.3dBi PASSBAND: 2405 to 2480 MHz LAN Antenna: Slot antenna: GAIN: 0dBi PASSBAND: 900 to 990 MHz

Date: 5/12/14 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Dear Sir or Madam: I hereby appoint Sam Wismer at Advanced Compliance Solutions, Inc. to act as our agent in the preparation of an application for equipment authorization of FCC ID: QHC-KVEVZE41 to the FCC Rules and Regulations. I certify that all exhibits contained within this filing properly describe the device or system for which authorization is sought. I further certify that appropriate arrangements have been made to assure that production units of this equipment bearing the name and FCC IDENTIFIER listed in this application will continue to comply with the Commission's requirements. I further certify by signature below that no party (per 47 CFR 1.2002(b)) to the application is subject to a denial of Federal benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). This appointment also includes the authority to complete FCC Form 731 on our behalf and sign the application as an authorized agent. Sincerely, Mike Mathis Mike Mathis Principal Certification Engineer

Date: May 12, 2014 Itron OEMs: This note serves as an additional agreement between Itron and its OEMs stating that the OEMs will use the Itron module kV2c-AMPZE in accordance with the FCC rules on limited modular approval devices. The unit will be professionally installed and all hosts will be tested for compliance with the kV2c-AMPZE module installed. Confidentiality of the Internal Photos is being requested because this is a non- consumer device which is not accessible by the general public, professionally installed, and is only serviceable by the applicant or designated technicians. Please feel free to contact me with any questions. Sincerely, Mike Mathis Mike Mathis Regulatory Engineer Itron Inc. 4400 Old Canton Road Suite 300 Jackson, MS 39211 [email protected]

CONFIDENTIALITY REQUEST Federal Communications Commission Date: 5/29/14 Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Gentlemen: Itron Inc. respectfully requests confidentiality of certain materials provided with the submission of the kV2c-AMPZE under FCC ID: QHC-KVEVZE41 in accordance with 47 CFR 0.457(d) and 47 CFR 0.459. The confidentiality request applies to the block diagram, theory of operation, and schematics contained in this filing and included in the following files: 14-0144 - Theory of Operation.pdf 14-0144 - System Block Diagram.pdf 14-0144 - Schematics.pdf 14-0144 – Internal Photos.pdf The kV2c-AMPZE has been developed at considerable effort and expense by Itron Inc. These items are considered as Trade Secrets and therefore public access to the proprietary material could possibly result in duplication of equipment that could severely damage the company's business advantage. Confidentiality of the Internal Photos is being requested because this is a non-consumer device which is not accessible by the general public, professionally installed, and is only serviceable by the applicant or designated technicians. I appreciate your assistance in this matter. Sincerely, Name: Mike Mathis Signature: Mike Mathis Title: Principal Regulatory Engineer Date: 5/29/14

5015 B. U. Bowman Dr. Buford, GA 30518 May 29, 2014 ACS TCB 5015 B.U. Bowman Drive Buford, GA 30518 Re: FCC ID: QHC-KVEVZE41 To Whom It May Concern: The following application is submitted on behalf of our client, Itron, for evaluation of their model 570974-001 for certification under FCC Part 15.247 for a limited modular approval. The 570974-001 is a module that is designed to be integrated into 2S, 3S, 4S, 9S, 12S, 16S and 45S electric utility meter forms. The 570974-001 includes (1) 900 MHz FHSS radio, (1) HAN 802.15.4 2.4 GHz Zigbee module and an on-board Sierra Wireless CDMA modem SL5011, FCC ID: N7NSL5011 / IC: 2417C- SL5011. The Sierra Wireless CDMA modem SL5011 is modular approved and not covered under the scope of this filing. The 570974-001 is designed to be integrated into 2S, 3S, 4S, 9S, 12S, 16S and 45S electric utility meter forms and be collocated and transmit simultaneously with the on-board Sierra Wireless CDMA modem SL5011 (FCC ID: N7NSL5011 / IC: 2417C-SL5011). The 570974-001 was tested in full to the requirements of the aforementioned rules and was found to be in compliance.The 570974-001 was also evaluated for intermodulation products due to simultaneous transmissions and found compliant. Sincerely, Sam Wismer Vice President, Technology Advanced Compliance Solutions, Inc.

Federal Communications Commission Date: May 12, 2014 P.O. Box 429 Columbia, MD 21045 RE: Application for Limited Modular Approval Certification for the kV2c-AMPZE module Dear Sir or Madam: The following information addresses the requirements to support a limited modular approval as required by FCC Part 15.212, Modular Transmitters. 1. The direct sequence spread spectrum transmitter and frequency hopping spread spectrum transmitter sections are not shielded. Testing has been performed to assure compliance. 2. The kV2c-AMPZE does not have external modulation or data inputs. The RF section is driven by an on board MCU which controls RF data lines and does not allow excessive modulation. 3. The modular transmitter has its own power regulation. The module will be integrated into a meter host which also offers power regulation. 4. The direct sequence transmitter has an antenna that is permanently imbedded into the module circuit board. 5. The frequency hopping spread spectrum transmitter has an antenna connected and permanently mounted under glass in the host meter. 6. The kV2c-AMPZE module was tested within a host meter. This module will always be integrated internal to a meter host. 7. The kV2c-AMPZE register module will be labeled as required. The meter host will also have the required labeling. 8. Operating requirements are included in the host technical manual. 9. MPE measurements are provided to demonstrate RF compliance. There is a cautionary statement that is included in the technical manual stipulating the 20 cm separation distance. All meter forms which act as hosts to the kV2c-AMPZE module will be tested with the kV2c-AMPZE module for compliance and documented through the permissive change process. Sincerely, Name: Mike Mathis Signature: Mike Mathis Title: Regulatory Engineer Date: May 12, 2014

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Certification Exhibit FCC ID: QHC-KVEVZE41 FCC Rule Part: 15.247 ACS Project Number: 14-0144 Manufacturer: Itron Model: 570974-001 External Photos Model: 570974-001FCC ID: QHC-KVEVZE41 ACS Project: 14-0144Advanced Compliance SolutionsPage 2 The EUT is a modular device in which internal photos have been held confidential. There are no associated external photographs considering the modular classification.

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Certification Exhibit FCC ID: QHC-KVEVZE41 FCC Rule Part: 15.247 ACS Project Number: 14-0144 Manufacturer: Itron Model: 570974-001 Label Information QHC-KVEVZE41 Module Label QHC-KVEVZE41 Module Label Placement FCC Label Placement QHC-KVEVZE41 Host Meter Label

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Certification Exhibit FCC ID: QHC-KVEVZE41 FCC Rule Part: 15.247 ACS Project Number: 14-0144 Manufacturer: Itron Model: 570974-001 RF Exposure Model: 570974-001FCC ID: QHC-KVEVZE41 ACS Project: 14-0144Advanced Compliance SolutionsPage 2 General Information: Applicant:Itron Device Category:Mobile Environment:General Population/Uncontrolled Exposure The 570974-001 is designed to be integrated into 2S, 3S, 4S, 9S, 12S, 16S and 45S electric utility meter forms and be collocated and transmit simultaneously with Sierra Wireless CDMA modem SL5011, FCC ID: N7NSL5011 / IC: 2417C-SL5011. Technical Information: Table 1: Technical Information (Including Collocated Transmitters on Board / In Host) Itron 900 MHz LAN module Model 570974-001 FCC ID: QHC-KVEVZE41 Itron 802.15.4 (Zigbee) module Model 570974-001 FCC ID: QHC-KVEVZE41 Sierra Wireless CDMA modem Model SL5011 FCC ID: N7NSL5011 IC: 2417C-SL5011 Antenna Type SlotPCB F-type Under Glass Ribbon External Monopole Antenna Gain 0 dBi3.3 dBi Under Glass Ribbon: 850 Band: 0 dBi 1900 Band: 0 dBi External Monopole: 850 Band: 3 dBi 1900 Band: 4 dBi Conducted Power 41.21 mW15.85 mW 850 Band: 748.17 mW* 1900 Band: 767.36 mW* Maximum Peak EIRP 41.21 mW33.88 mW 850 Band: 1492.79 mW 1900 Band:1927.52 mW Maximum Peak ERP 25.12 mW20.65 mW 850 Band: 909.91 mW 1900 Band:1174.90 mW * Power provided for FCC ID: N7NSL5011 is power as listed on the grant and measured in the original FCC certification filing. Note: Maximum EIRP/ERP calculated based on maximum antenna gain where multiple antennas are applicable. Model: 570974-001FCC ID: QHC-KVEVZE41 ACS Project: 14-0144Advanced Compliance SolutionsPage 3 MPE Calculation The Power Density (mW/cm 2 ) is calculated as follows: S = 2 4R PG  Where: S = power density (in appropriate units, e.g. mW/cm2) P = power input to the antenna (in appropriate units, e.g., mW) G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna (appropriate units, e.g., cm) Table 2: MPE Calculation (Including Collocated Devices) MPE Calculator for Mobile Equipment Limits for General Population/Uncontrolled Exposure* 914.816.150.6141.2101.000 200.008 2475121.0015.853.32.138 200.007 824.728.740.55748.173.01.995 200.297 188028.851.00767.364.02.512 200.383 Power Density (mW/cm^2) Distance (cm) Transmit Frequency (MHz) Radio Power (dBm) Power Density Limit (mW/Cm2) Radio Power (mW) Antenna Gain (dBi) Antenna Gain (mW eq.) Summation of Power Densities – Simultaneous Transmissions This device contains multiple transmitters which can operate simultaneously and is collocated with additional transmitters in host integration; therefore the maximum RF exposure is determined by the summation of MPE ratios. The limit is such that the summation of MPE ratios is ≤ 1.0. The summation of MPE ratios is as follows: SL5011 Modem Operating in the 850 Band: 900 LAN MPE Ratio + 802.15.4 MPE Ratio + SL5011 850 MPE Ratio (0.008 / 0.61) + (0.007 / 1.0) + (0.297 / 0.55) = (0.013) + (0.007) + (0.540) = 0.560 0.560 < 1 SL5011 Modem Operating in the 1900 PCS Band: 900 LAN MPE Ratio + 802.15.4 MPE Ratio + SL5011 1900 MPE Ratio (0.008 / 0.61) + (0.007 / 1.0) + (0.383 / 1.0) = (0.013) + (0.007) + (0.383) = 0.403 0.403 < 1 RF Exposure In accordance with FCC requirements of human exposure to radio frequency fields, the radiating element shall be installed such that a minimum separation distance of 20 centimeters will be maintained. Conclusion This device complies with the MPE requirements by providing adequate separation between the device, any radiating structure and the general population.

Certification Test Report FCC ID: QHC-KVEVZE41 FCC Rule Part: 15.247 ACS Report Number: 14-0144.W03.1A Manufacturer: Itron Model: 570974-001 Test Begin Date: April 21, 2014 Test End Date: May 9, 2014 Report Issue Date: May 29, 2014 FOR THE SCOPE OF ACCREDITATION UNDER LAB Code 200612-0 This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. Reviewed by: Kirby Munroe Director, Wireless Certifications ACS, Inc. This test report shall not be reproduced except in full. This report may be reproduced in part with prior written consent of ACS, Inc. The results contained in this report are representative of the sample(s) submitted for evaluation. This report contains 30 pages 5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 TABLE OF CONTENTS 1 GENERAL ............................................................................................................................................ 3 1.1 PURPOSE .......................................................................................................................................... 3 1.2 PRODUCT DESCRIPTION ................................................................................................................... 3 1.3 TEST METHODOLOGY AND CONSIDERATIONS ................................................................................. 4 2 TEST FACILITIES .............................................................................................................................. 5 2.1 LOCATION ....................................................................................................................................... 5 2.2 LABORATORY ACCREDITATIONS/RECOGNITIONS/CERTIFICATIONS ................................................ 5 2.3 RADIATED EMISSIONS TEST SITE DESCRIPTION .............................................................................. 6 2.3.1 Semi-Anechoic Chamber Test Site .......................................................................................... 6 2.3.2 Open Area Tests Site (OATS) ................................................................................................. 7 2.4 CONDUCTED EMISSIONS TEST SITE DESCRIPTION ........................................................................... 8 3 APPLICABLE STANDARD REFERENCES .................................................................................... 8 4 LIST OF TEST EQUIPMENT ............................................................................................................ 9 5 SUPPORT EQUIPMENT ...................................................................................................................10 6 EQUIPMENT UNDER TEST SETUP BLOCK DIAGRAM ..........................................................10 7 SUMMARY OF TESTS ......................................................................................................................11 7.1 ANTENNA REQUIREMENT – FCC 15.203 ........................................................................................11 7.2 POWER LINE CONDUCTED EMISSIONS – FCC 15.207, IC: RSS-GEN 7.2.4 .....................................11 7.2.1 Measurement Procedure ........................................................................................................11 7.2.2 Measurement Results .............................................................................................................11 7.3 6DB / 99% BANDWIDTH – FCC 15.247(A)(2), IC: RSS-210 A8.2(A) .............................................21 7.3.1 Measurement Procedure ........................................................................................................21 7.3.2 Measurement Results .............................................................................................................21 7.4 FUNDAMENTAL EMISSION OUTPUT POWER – FCC 15.247(B)(3), IC: RSS-210 A8.4(4) ................23 7.4.1 Measurement Procedure ........................................................................................................23 7.4.2 Measurement Results .............................................................................................................23 7.5 EMISSION LEVELS – FCC 15.247(D), 15.205, 15.209; IC RSS-210 2.2/A8.5, RSS-GEN 7.2.2 ........24 7.5.1 Emissions into Non-restricted Frequency Bands ...................................................................24 7.5.1.1 Measurement Procedure ................................................................................................................... 24 7.5.1.2 Measurement Results ....................................................................................................................... 24 7.5.2 Emissions into Restricted Frequency Bands ..........................................................................27 7.5.2.1 Measurement Procedure ................................................................................................................... 27 7.5.2.2 Duty Cycle Correction ..................................................................................................................... 27 7.5.2.3 Measurement Results ....................................................................................................................... 27 7.5.2.4 Sample Calculation: ......................................................................................................................... 28 7.6 MAXIMUM POWER SPECTRAL DENSITY IN THE FUNDAMENTAL EMISSION – FCC 15.247(E) IC: RSS-210 A8.2(B) .......................................................................................................................................29 7.6.1 Measurement Procedure ........................................................................................................29 7.6.2 Measurement Results ...............................................................................…

Text truncated - open the document above for the full version.

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Certification Exhibit FCC ID: QHC-KVEVZE41 FCC Rule Part: 15.247 ACS Project Number: 14-0144 Manufacturer: Itron Model: 570974-001 Test Setup Photos Model: 570974-001FCC ID: QHC-KVEVZE41 ACS Project: 14-0144Advanced Compliance SolutionsPage 2 Figure 1: Radiated Emissions – 2S Meter Form Internal Antenna Figure 2: Radiated Emissions – 2S Meter Form Internal Antenna Model: 570974-001FCC ID: QHC-KVEVZE41 ACS Project: 14-0144Advanced Compliance SolutionsPage 3 Figure 3: Radiated Emissions – 3S Meter Form Internal Antenna Figure 4: Radiated Emissions – 3S Meter Form Internal Antenna Model: 570974-001FCC ID: QHC-KVEVZE41 ACS Project: 14-0144Advanced Compliance SolutionsPage 4 Figure 5: Radiated Emissions – 4S Meter Form Internal Antenna Figure 6: Radiated Emissions – 4S Meter Form Internal Antenna Model: 570974-001FCC ID: QHC-KVEVZE41 ACS Project: 14-0144Advanced Compliance SolutionsPage 5 Figure 7: Radiated Emissions – 9S Meter Form Internal Antenna Figure 8: Radiated Emissions – 9S Meter Form Internal Antenna Model: 570974-001FCC ID: QHC-KVEVZE41 ACS Project: 14-0144Advanced Compliance SolutionsPage 6 Figure 9: Radiated Emissions – 12S Meter Form Internal Antenna Figure 10: Radiated Emissions – 12S Meter Form Internal Antenna Model: 570974-001FCC ID: QHC-KVEVZE41 ACS Project: 14-0144Advanced Compliance SolutionsPage 7 Figure 11: Radiated Emissions – 12S Meter Form External Antenna Figure 12: Radiated Emissions – 12S Meter Form External Antenna Model: 570974-001FCC ID: QHC-KVEVZE41 ACS Project: 14-0144Advanced Compliance SolutionsPage 8 Figure 13: Radiated Emissions – 16S Meter Form Internal Antenna Figure 14: Radiated Emissions – 16S Meter Form Internal Antenna Model: 570974-001FCC ID: QHC-KVEVZE41 ACS Project: 14-0144Advanced Compliance SolutionsPage 9 Figure 15: Radiated Emissions – 16S Meter Form External Antenna Figure 16: Radiated Emissions – 16S Meter Form External Antenna Model: 570974-001FCC ID: QHC-KVEVZE41 ACS Project: 14-0144Advanced Compliance SolutionsPage 10 Figure 17: Radiated Emissions – 45S Meter Form Internal Antenna Figure 18: Radiated Emissions – 45S Meter Form Internal Antenna Model: 570974-001FCC ID: QHC-KVEVZE41 ACS Project: 14-0144Advanced Compliance SolutionsPage 11 Figure 19: Conducted Emissions – 2S Meter Form Figure 20: Conducted Emissions – 2S Meter Form Model: 570974-001FCC ID: QHC-KVEVZE41 ACS Project: 14-0144Advanced Compliance SolutionsPage 12 Figure 21: Conducted Emissions – 3S Meter Form Figure 22: Conducted Emissions – 3S Meter Form Model: 570974-001FCC ID: QHC-KVEVZE41 ACS Project: 14-0144Advanced Compliance SolutionsPage 13 Figure 23: Conducted Emissions – 4S Meter Form Figure 24: Conducted Emissions – 4S Meter Form Model: 570974-001FCC ID: QHC-KVEVZE41 ACS Project: 14-0144Advanced Compliance SolutionsPage 14 Figure 25: Conducted Emissions – 9S Meter Form Figure 26: Conducted Emissions – 9S Meter Form Model: 570974-001FCC ID: QHC-KVEVZE41 ACS Project: 14-0144Advanced Compliance SolutionsPage 15 Figure 27: Conducted Emissions – 12S Meter Form Figure 28: Conducted Emissions – 12S Meter Form Model: 570974-001FCC ID: QHC-KVEVZE41 ACS Project: 14-0144Advanced Compliance SolutionsPage 16 Figure 29: Conducted Emissions – 16S Meter Form Figure 30: Conducted Emissions – 16S Meter Form Model: 570974-001FCC ID: QHC-KVEVZE41 ACS Project: 14-0144Advanced Compliance SolutionsPage 17 Figure 31: Conducted Emissions – 45S Meter Form Figure 32: Conducted Emissions – 45S Meter Form