QHC-OW35SEOpenWay 3.5S

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Certification Exhibit FCC ID: QHC-OW35SE IC: 4393B-OW35SE FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-210 ACS Project Number: 14-0309 Manufacturer: Itron, Inc. Model: 574023 OpenWay 3.5S User Information Manual OpenWay 3.5S User Information Manual Itron Model 574023 OpenWay 3.5S User Information Manual Labeling The following requirements will be applied to any products that use this module: The end product label will include the following text: Contains: FCC ID: QHC-OW35SE IC: 4393B-OW35SE Model: 574023 The user’s manual for any product that contains this module will contain the following test. If the device is large enough, this information will also placed on the label: “THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS. (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.” Regulatory Compliance The user’s manual for any product that contains this module will contain the following text: FCC Part 15, Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. OpenWay 3.5S User Information Manual Industry Canada This device complies with Part 15 of the FCC Rules [and with RSS-210 of Industry Canada]. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Under Industry Canada regulations, this radio transmitter may only operate using antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. En vertu de la réglementation d'Industrie Canada, cet émetteur radio peut fonctionner uniquement à l'aide de l'antenne d'un type et maximale (ou moins) obtenir une approbation pour l'émetteur par Industrie Canada. Pour réduire les interférences radio potentielles à d'autres utilisateurs, le type d'antenne et son gain doivent être choisie que la puissance isotrope rayonnée équivalente (p.i.r.e.) n'est pas plus que celui nécessaire à une communication efficace. RF Exposure The antennas used for this transmitter must be installed to provide a minimum separation distance of 20 cm from all persons, and must not be co-located or operate in conjunction with any other antenna or transmitter. End users and installers must be provided with antenna installation procedures and transmitter operating conditions for satisfying RF exposure compliance. Miscellaneous The user’s manual for any product that contains this module will contain the following text: Professional Installation This module is intended for professional installation by the integrator. The OEM integrator is still responsible for the FCC compliance requirement of the end product which uses this module. Modification and Repairs To ensure FCC compliance and system performance, this device, antenna and/or coaxial assembly shall not be changed or modified without the express written approval of Itron. Any unauthorized modification OpenWay 3.5S User Information Manual will void the user’s authority to operate the equipment. WARNING! This device contains no user serviceable parts. Attempts to repair this device by unauthorized personnel may subject the person to shock hazard if removal of protective covers is attempted. Unauthorized repair will void the warranty and/or any maintenance contract with your company. General Description The Itron OpenWay 3.5S is an electricity metering module which includes a Cellular LTE WAN module operating in the LTE Bands 4 & 13.and a LAN transmitter operating in the 902 MHz to 928 and. The module operates on DC voltage & current which is supplied by the host meter device. ANTENNAS This radio transmitter 4393B-OW35SE has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le présent émetteur radio (identifier le dispositif par son numéro de certification ou son numéro de modèle s'il fait partie du matériel de catégorie I) a été approuv…

Text truncated - open the document above for the full version.

Date:031091{5 Federal Communications Commission Equipment Authorization BrancJt 7{85 Oakland Mills Road Columbia. MD 210dti Dear Sir or Madam: I hereby appoint Sam tMsmer at Advanced Compliance Solutions, lnc. to aci as our agent in the preparation of an application for equipment authorizdion of FCC lD: QHC-O\AESSE to the FCC Rules and Regulations. I cerffi that all e*ribib contained within this filing properly describe the devie or system forwticfi authodzation is sought. | further certiff that appropriate arrangements have been made to aseure that produciion units of this equipment beadng the name and FCG IDENTIFIER listed ln ffiis application will continue to comply rvith the Commission's rcquiemenb. I further certify by signature belor that no party (p* 47 CFR 1.2002(b)) to the application is subject to a denial of Federal benefits, including FCC benefiis, pursuant to Sedion 5301 of lhe Anti-Drug Abuse Acf of 1988, 21 U.S.C. 853(a). This appointnent also indude the authority to cornplete FCC Form 731 on our behalf and sign the appli<ntion as an authodzed agent. Sincerely, ttikeltathis rurh Pri nc ipal Certification En gi neer

5015 B. U. Bowman Dr. Buford, GA 30518 April 7, 2015 ACS TCB 5015 B.U. Bowman Drive Buford, GA 30518 Re: FCC ID: QHC-OW35SE To Whom It May Concern: The following application is submitted on behalf of our client, Itron, for evaluation of their model 574023 for certification under FCC Part 15.247 for a limited modular approval certification. The 574023 is a module that is designed to be integrated into 1S, 2S, and 12S electric utility meter forms. The 574023 includes (1) 900 MHz FHSS radio and an on-board Sierra Wireless LTE modem HL7518, FCC ID: N7NNH7518. The Sierra Wireless LTE modem HL7518 is modular approved and not covered under the scope of this filing. The 574023 is designed to be integrated into 1S, 2S, and 12S electric utility meter forms and be collocated and transmit simultaneously with the on-board Sierra Wireless LTE modem HL7518 (FCC ID: N7NNH7518) and separate Itron module ITR24 FCC ID: SK9ITR24 / IC: 864G-ITR24. The 574023 was tested in full to the requirements of the aforementioned rules and was found to be in compliance. The 574023 was also evaluated for intermodulation products due to simultaneous transmissions and found compliant. Sincerely, Sam Wismer Vice President, Technology Advanced Compliance Solutions, Inc.

llron Federal Cornrnunications Comrnission P.O. Box 4?g Coilurnbia, MD 21045 Date: Marcfi 09, 2015 RE: Applioation for Limited ModularApproval Certifioation fiorthe OpenWay 3.5S module Dear Sir or Madam: The following information addresses the requirements to support a limited modular approval as required by FCG Part 1$.212, ModularTmnsmitters. 1. The frequency hopping spread spectrum transmittrer sectbn is shielded. Testing has been perbnned to assurc compliance. 2. The OpenWay 3.5S does not have extemal modulation or data inpub. The RF sec'ttbn is driven by an on board l$OM which controls RF data lines and does not allow excessive modulation. The modular transmitter has its o$,n power regulation. The module will be integrated into a meter hostwhich also ofiers pourer regulation. The @uency hopping sprmd spectrum transmitter has an antenna connecbd and pennanenfly mounted on the module under glass in the host meter. The OpenWay 3.5S module was tested wihin a host meteL This module will always be integrated internal to a meter host 6. The OpenWay 3.5S regisbr module will be labeled as required. The meter host will also have the required labeling. 7. Operating requiremenF are included in the host technical manual. 8. MPE measurcments arc provided to demonstrate RF compliance. There is a cautionary staternent that is included in the technical manual stipulating the 20 cm separation distance. All meter forms wtrich act as ho6ts b the OpenWay 3.5$ module $rill be tested with the OpenWay 3.5$ module forcompliance and documenEd thragh the permissive change process. $incerely, 3. 4. 5. Signature: M Narne: IVIike Mathis Title: Regutatory EngineerDate: March 09, 2015

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Certification Exhibit FCC ID: QHC-OW35SE IC: 4393B-OW35SE FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-210 ACS Project Number: 14-0309 Manufacturer: Itron, Inc. Model: 574023 Model: 574023FCC ID: QHC-OW35SEIC: 4393B-OW35SE ACS Project: 14-0309Advanced Compliance SolutionsPage 2 Figure 1: Representative Host Figure 2: Internal Photo Model: 574023FCC ID: QHC-OW35SEIC: 4393B-OW35SE ACS Project: 14-0309Advanced Compliance SolutionsPage 3 Figure 3: Internal Photo Figure 4: Internal Photo 2.4 GHz 802.15.4 Zigbee RF Section EUT and Antenna FCC ID: QHC-OW35SE Model: 574023FCC ID: QHC-OW35SEIC: 4393B-OW35SE ACS Project: 14-0309Advanced Compliance SolutionsPage 4 Figure 5: Internal Photo Figure 6: Internal Photo – Shields Removed Collocated on board FCC ID: N7NSL5011 IC:2417C-SL5011 900 MHz LAN RF Section Model: 574023FCC ID: QHC-OW35SEIC: 4393B-OW35SE ACS Project: 14-0309Advanced Compliance SolutionsPage 5 Figure 7: Internal Photo Figure 8: Internal Photo – Shield Removed Model: 574023FCC ID: QHC-OW35SEIC: 4393B-OW35SE ACS Project: 14-0309Advanced Compliance SolutionsPage 6 Figure 9: Internal Photo – Sierra Wireless N7N7518 Figure 10: Internal Photo – 900MHz Radio Shield Removed Collocated on board FCC ID: N7NSL5011 IC:2417C-SL5011 Model: 574023FCC ID: QHC-OW35SEIC: 4393B-OW35SE ACS Project: 14-0309Advanced Compliance SolutionsPage 7 Figure 11: Internal Photo – ISOM Module U1 Shield Removed

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Certification Exhibit FCC ID: QHC-OW35SE IC: 4393B-OW35SE FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-210 ACS Project Number: 14-0309 Manufacturer: Itron, Inc. Model: 574023 FCC & IC LABEL ON THE MODULE FCC 15.19 & ICES-003 LABEL ON THE MODULE THIS DEVICE COMPLIES WITHPART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: 1. THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND 2. THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. FCC & IC LABEL ON HOST METER FCC & IC COMPLIANCE LABEL ON HOST METER

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Certification Exhibit FCC ID: QHC-OW35SE IC: 4393B-OW35SE FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-210 ACS Project Number: 14-0309 Manufacturer: Itron, Inc. Model: 574023 Model: 574023FCC ID: QHC-OW35SEIC: 4393B-OW35SE ACS Project: 14-0309Advanced Compliance SolutionsPage 2 Figure 1: Representative Host Figure 2: Internal Photo Model: 574023FCC ID: QHC-OW35SEIC: 4393B-OW35SE ACS Project: 14-0309Advanced Compliance SolutionsPage 3 Figure 3: Internal Photo Figure 4: Internal Photo 2.4 GHz 802.15.4 Zigbee RF Section EUT and Antenna FCC ID: QHC-OW35SE Model: 574023FCC ID: QHC-OW35SEIC: 4393B-OW35SE ACS Project: 14-0309Advanced Compliance SolutionsPage 4 Figure 5: Internal Photo Figure 6: Internal Photo – Shields Removed Collocated on board FCC ID: N7NSL5011 IC:2417C-SL5011 900 MHz LAN RF Section Model: 574023FCC ID: QHC-OW35SEIC: 4393B-OW35SE ACS Project: 14-0309Advanced Compliance SolutionsPage 5 Figure 7: Internal Photo Figure 8: Internal Photo – Shield Removed Model: 574023FCC ID: QHC-OW35SEIC: 4393B-OW35SE ACS Project: 14-0309Advanced Compliance SolutionsPage 6 Figure 9: Internal Photo – Sierra Wireless N7N7518 Figure 10: Internal Photo – 900MHz Radio Shield Removed Collocated on board FCC ID: N7NSL5011 IC:2417C-SL5011 Model: 574023FCC ID: QHC-OW35SEIC: 4393B-OW35SE ACS Project: 14-0309Advanced Compliance SolutionsPage 7 Figure 11: Internal Photo – ISOM Module U1 Shield Removed

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Certification Exhibit FCC ID: QHC-OW35SE IC: 4393B-OW35SE FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-210 ACS Project Number: 14-0309 Manufacturer: Itron, Inc. Model: 574023 RF Exposure Model: 574023 FCC ID:QHC-OW35SE IC: 4393B-OW35SE ACS Project: 14-0309 Advanced Compliance Solutions Page 2 General Information: Applicant: Itron Inc. Device Category: Mobile Environment: General Population/Uncontrolled Exposure The 574023 is designed to be integrated into 1S, 2S and 12S electric utility meter forms and be collocated and transmit simultaneously with the on-board Sierra Wireless LTE modem HL7518, FCC ID: N7NHL7518 and separate Itron module ITR24 FCC ID: SK9ITR24 / 864G-ITR24. Note: The on-board Sierra Wireless LTE modem HL7518 is not available for use in Canadian territories. Technical Information: Table 1: Technical Information (Including Collocated Transmitters On Board / In Host) Itron 900 MHz LAN module Model 574023 FCC ID: QHC-OW35SE IC: 4393B-OW35SE Itron 802.15.4 (Zigbee) module Model ITR24 FCC ID: SK9ITR24 IC:864G-ITR24 Sierra Wireless LTE modem Model HL7518 FCC ID: N7NHL7518 (IC Not Applicable) Antenna Type Inverted F PCB quarter wave embedded slot Inverted F Antenna Gain 2.4dBi 3.8 dBi Band 13 (700MHz): 3.15 dBi Band 4 (1700MHz): 3.15 dBi Conducted Power 599.79mW 63.53 mW Band 13 (700MHz): 201 mW* Band 4 (1700MHz): 211 mW* Maximum Peak EIRP 1042.32 mW 152.41 mW Band 13 (700MHz): 415.14 mW Band 4 (1700MHz): 435.80 mW Maximum Peak ERP 635.33 mW 92.90 mW Band 13 (700MHz): 253.04 mW Band 4 (1700MHz): 265.63 mW * Power provided for FCC ID: N7NHL7518 is power as listed on the grant and measured in the original FCC certification filing. Model: 574023 FCC ID:QHC-OW35SE IC: 4393B-OW35SE ACS Project: 14-0309 Advanced Compliance Solutions Page 3 MPE Calculation (FCC) The Power Density (mW/cm 2 ) is calculated as follows: S = 2 4R PG  Where: S = power density (in appropriate units, e.g. mW/cm2) P = power input to the antenna (in appropriate units, e.g., mW) G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna (appropriate units, e.g., cm) Table 2: MPE Calculation (Including Collocated Devices) MPE Calculator for Mobile Equipment Limits for General Population/Uncontrolled Exposure* 91027.780.61599.792.41.738 200.207 247518.031.0063.533.82.399200.030 784.523.040.52201.373.152.065200.083 1717.523.241.00210.863.152.065200.087 Power Density (mW/cm^2) Distance (cm) Transmit Frequency (MHz) Radio Power (dBm) Power Density Limit (mW/Cm2) Radio Power (mW) Antenna Gain (dBi) Antenna Gain (mW eq.) Summation of Power Densities – Simultaneous Transmissions This device contains multiple transmitters which can operate simultaneously and is collocated with additional transmitters in host integration; therefore the maximum RF exposure is determined by the summation of MPE ratios. The limit is such that the summation of MPE ratios is ≤ 1.0. The summation of MPE ratios is as follows: HL7518 Modem Operating in the 700 MHz Band 13: 900 LAN MPE Ratio + 802.15.4 MPE Ratio + HL7518 700 MPE Ratio ( 0.207 / 0.61) + (0.030 / 1.0) + (0.083 / 0.52) = (0.339) + (0.030) + (0.160) = 0.529 0.529 < 1 HL7518 Modem Operating in the 1700 MHz Band 4: 900 LAN MPE Ratio + 802.15.4 MPE Ratio + HL7518 1700 MPE Ratio ( 0.207 / 0.61) + (0.030 / 1.0) + (0.087 / 1.0) = (0.339) + (0.030) + (0.087) = 0.456 0.456 < 1 Exemption From Routine RF Exposure Evaluation (IC) The on-board Sierra Wireless LTE modem HL7518 is not available for use in Canadian territories and therefore should not be included in determining compliance with RF exposure. The Itron 900 MHz LAN module (IC: 4393B-OW35SE) and Itron 802.15.4 Zigbee module (IC: 864G-ITR24) comply with the exemption limits for routine RF exposure evaluation per RSS-102 Issue 5. The source-based, time-averaged maximum EIRP thresholds for exemption from routine RF exposure evaluation are as follows: Itron 900 MHz LAN module (910 MHz): 1.38 W EIRP Itron 802.15.4 Zigbee module (2405 MHz): 2.68 W EIRP Model: 574023 FCC ID:QHC-OW35SE IC: 4393B-OW35SE ACS Project: 14-0309 Advanced Compliance Solutions Page 4

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 7708318048 Fax: 7708318598 Certification Test Report FCC ID: QHC-OW355SE IC: 4393B-OW35SE FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-210 ACS Report Number: 14-0309.W06.1B Manufacturer: Itron, Inc. Model: 574023 Test Begin Date: March 9, 2015 Test End Date: March 12, 2015 Report Issue Date: April 22, 2015 FOR THE SCOPE OF ACCREDITATION UNDER LAB Code 2006120 This report is not be used to claim certification, approval, or endorsement by NVLAP, NIST or any government agency. Reviewed by: Kirby Munroe Director, Wireless Certifications ACS, Inc. This test report shall not be reproduced except in full. This report may be reproduced in part with prior written consent of ACS, Inc. The results contained in this report are representative of the sample(s) submitted for evaluation. This report contains 25 pages 5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 7708318048 Fax: 7708318598 TABLE OF CONTENTS 1 GENERAL ............................................................................................................................................ 3 1.1 PURPOSE .......................................................................................................................................... 3 1.2 PRODUCT DESCRIPTION ................................................................................................................... 3 1.3 TEST METHODOLOGY AND CONSIDERATIONS ................................................................................. 4 2 TEST FACILITIES .............................................................................................................................. 5 2.1 LOCATION ....................................................................................................................................... 5 2.2 LABORATORY ACCREDITATIONS/RECOGNITIONS/CERTIFICATIONS ................................................ 5 2.3 RADIATED EMISSIONS TEST SITE DESCRIPTION .............................................................................. 6 2.3.1 Semi-Anechoic Chamber Test Site .......................................................................................... 6 2.3.2 Open Area Tests Site (OATS) ................................................................................................. 7 2.4 CONDUCTED EMISSIONS TEST SITE DESCRIPTION ........................................................................... 8 3 APPLICABLE STANDARD REFERENCES .................................................................................... 8 4 LIST OF TEST EQUIPMENT ............................................................................................................ 9 5 SUPPORT EQUIPMENT ...................................................................................................................10 6 EQUIPMENT UNDER TEST SETUP BLOCK DIAGRAM ..........................................................10 7 SUMMARY OF TESTS ......................................................................................................................11 7.1 ANTENNA REQUIREMENT – FCC: SECTION 15.203 ........................................................................11 7.2 POWER LINE CONDUCTED EMISSIONS – FCC 15.207, IC: RSS-GEN 8.8 ........................................11 7.2.1 Measurement Procedure ........................................................................................................11 7.2.2 Measurement Results .............................................................................................................11 7.3 PEAK OUTPUT POWER - FCC 15.247(B)(2) IC: RSS-210 A8.4(1) ..................................................15 7.3.1 Measurement Procedure (Conducted Method) ......................................................................15 7.3.2 Measurement Results .............................................................................................................15 7.4 CHANNEL USAGE REQUIREMENTS .................................................................................................16 7.4.1 Carrier Frequency Separation – FCC 15.247(a)(1) IC: RSS-210 A8.1(b) ............................16 7.4.1.1 Measurement Procedure ................................................................................................................... 16 7.4.1.2 Measurement Results ....................................................................................................................... 16 7.4.2 Number of Hopping Channels – FCC 15.247(a)(1)(i) IC: RSS-210 A8.1(c) .........................17 7.4.2.1 Measurement Procedure ................................................................................................................... 17 7.4.2.2 Measurement Results ....................................................................................................................... 17 7.4.3 Channel Dwell Time – FCC 15.247(a)(1)(i) IC: RSS-210 A8.1(c) ........................................18 7.4.3.1 Measurement Procedure ................................................................................................................... 18 7.4.3.2 Measurement Results ....................................................................................................................... 18 7.4.4 20dB / 99% Bandwidth - FCC 15.247(a)(1)(i) IC: RSS-210 A8.2(a) ...................................19 7.4.4.1 Measurement Procedure ................................................................................................................... 19 7.4.4.2 Measurement Results ....................................................................................................................... 19 7.5 BAND-EDGE COMPLIANCE AND SPURIOUS EMISSIONS ...................................................................21 7.5.1 Band-Edge Compliance of RF Conducted Emissions - FCC 15.247(d); IC RSS-210 A8.5 ...21 7.5.1.1 Measurement Procedure ..............…

Text truncated - open the document above for the full version.

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Certification Exhibit FCC ID: QHC-OW35SE IC: 4393B-OW35SE FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-210 ACS Project Number: 14-0309 Manufacturer: Itron, Inc. Model: 574023 Model: 574023FCC ID: QHC-OW35SEIC: 4393B-OW35SE ACS Project: 14-0309Advanced Compliance SolutionsPage 2 Figure 1: Radiated Emissions – 1S Meter Figure 2: Radiated Emissions – 1S Meter Model: 574023FCC ID: QHC-OW35SEIC: 4393B-OW35SE ACS Project: 14-0309Advanced Compliance SolutionsPage 3 Figure 3: Radiated Emissions – 2S Meter Figure 4: Radiated Emissions – 2S Meter Model: 574023FCC ID: QHC-OW35SEIC: 4393B-OW35SE ACS Project: 14-0309Advanced Compliance SolutionsPage 4 Figure 5: Radiated Emissions – 12S Meter Figure 6: Radiated Emissions – 12S Meter Model: 574023FCC ID: QHC-OW35SEIC: 4393B-OW35SE ACS Project: 14-0309Advanced Compliance SolutionsPage 5 Figure 7: Conducted Emissions – 1S Meter Figure 8: Conducted Emissions – 1S Meter Model: 574023FCC ID: QHC-OW35SEIC: 4393B-OW35SE ACS Project: 14-0309Advanced Compliance SolutionsPage 6 Figure 9: Conducted Emissions – 2S Meter Figure 10: Conducted Emissions – 2S Meter Model: 574023FCC ID: QHC-OW35SEIC: 4393B-OW35SE ACS Project: 14-0309Advanced Compliance SolutionsPage 7 Figure 11: Conducted Emissions – 12S Meter Figure 12: Conducted Emissions – 12S Meter