QLBPT11MHFHSS TRANSMITTER

Pegasus Technologies, Inc. PT11MHTransceiver Users Manual (Preliminary) RF Transceiver Installation Instructions The PT11MH Transceiver Frequency Hopping Spread Spectrum transceiver. This transceiver should only be installed by qualified service personnel. The transceiver detects level, low battery or other data signals from the external binary inputs and broadcasts that data to the system's host receiver. MOUNTING LOCATION The PT11MH Transceiver is a module as defined by the FCC and therefore must be mounted to another host device in order to function. This device is intended only for OEM integrators under the following conditions: 1) The integrator must position this device in any end product such that the antenna to user/bystander distance is greater than 20 cm when the transmitter is functioning (excluding hands, wrists, feet and ankles). 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as the 2 conditions above are met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions can not be met (for example applications where the antenna to user distance is < 20 cm or to be co-located with another transmitter), then the original FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. NOTICE TO CUSTOMER Any Pegasus Technologies customer incorporating the PT11MH transceiver module into its own product must have an external notice affixed to its product. This notice must be placed in a conspicuous location and can use wording such as: “Contains FCC ID: QLBPT11MH” or “Contains Transceiver Module FCC ID: QLBPT11MH”. Any similar wording that expresses the same meaning may be used. NOTE: The end user should NOT be provided any instructions on how to remove or install the device. RF Exposure Manual Information That Must be Included to End User The users manual for end users must include the following information in a prominent location "IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter." INSTALLATION INSTRUCTIONS 1. Supply the transceiver with DC power by inserting a 3.6 Volt battery into the battery holder on the customers host application circuit board. 2. The unit will come pre-programmed with a Network ID and Hop Seed. However, the customer does have the option of field programming the unit. 3. If possible, avoid installing the PT11MH in areas near large metallic objects such as air conditioners, heaters, screens and heaters. CAUTION: This device is required to comply with FCC RF exposure requirements for mobile and fixed transmitting devices. The FCC requires that the antenna used for this transmitter must be installed to provide a separation of at least 20 cm (8 inches) from all persons (not including hands, wrists, feet, and ankles) and must not be co-located or operating in conjunction with any other antenna or transmitter. FCC NOTICE The Model PT11MH transceiver generates and uses radio frequency energy. If not installed and used in accordance with the manufacturer's instructions, it may cause interference to radio and television reception. The transceiver has been tested and found to comply with the specifications in Part 15 of FCC Rules for Spread Spectrum Intentional Radiators and FCC Part 15 Subpart C, Specifications. If this equipment causes interference to radio or television reception - which can be determined by turning the equipment on and off - the installer is encouraged to correct the interference by one or more of the following measures: 1) Reorient the antenna of the radio/television. 2) Connect the AC transformer to a different outlet so the control panel and radio/television are on different branch circuits. 3) Relocate the control panel with respect to the radio/television. If necessary, the installer should consult an experienced radio/television technician for additional suggestions, or send for the "Interference Handbook" prepared by the Federal Communications Commission. This booklet is available from the U.S. Government Printing Office, Washington, D.C., 20402, stock number 004-000-00450-7. CAUTION: No field changes or modifications to the PT11MH should be made unless they are specifically covered in this manual. All adjustments must be made at the factory under the specific guidelines set forth in our manufacturing processes. Any modification to the equipment could void the user's authority to operate the equipment and render the equipment in violation of FCC Part 15, Subpart C, 15.247. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. LIMITED WARRANTY THERE ARE NOT WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. In no case shall Seller be liable to anyone for any consequential or incidental damages for breach of this or any other warranty, express or implied, or upon any other basis of liability whatsoever, even if the loss or damage is caused by Seller's own negligence or fault.

Pegasus Technologies, Inc. 108 Pawnook Farm Road Lenoir City, TN 37771 Phone 865-717-9339 Fax 865-717-9904 Email [email protected] CONFIDENTIALITY REQUEST Federal Communications Commission Date: 8/20/2007 Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Gentlemen: Pegasus Technologies, Inc respectfully requests confidentiality of certain materials provided with the submission of the PT11MH under FCC ID: QLB in accordance with FCC Regulations 0.459. The confidentiality request applies to the Block Diagram, file 07-0186.Block Diagram.pdf Schematics, File 07-0186.Schematics.pdf and Principles of Operation , file 07-0186.Operational Theory.pdf. The PT11MH has been developed at considerable effort and expense by Pegasus Technologies, Inc. These items are considered as Trade Secrets and therefore public access to the proprietary material could possible result in duplication of equipment that could severely damage the company's business advantage. I appreciate your assistance in this matter. Sincerely, James W Pearce, President

Pegasus Technologies 254 Babbs Road Lenoir City, TN 37771 Phone 865-483-7748 Fax 775-261-0914 Email [email protected] Re: modular transmitter approval Gentlemen: Public Notice DA00-1407 regarding Part 15 unlicensed modular transmitters requires that the following information be addressed. The transmitter module is a complete RF transmitter containing its own reference oscillator. The connections available on the module are for power, data and antenna. Below please find information, addressing each paragraph from DA00-1407, requested about the unit. 1.) The unit has its own RF shield to prevent coupling between the RF circuitry of the module and any wires or circuits in the device into which the module is installed. Please see the included photographs. 2.) The unit buffers all input signals through its digital logic. 3.) The unit has power regulation incorporated in the circuitry to ensure continued compliance regardless of the design of the power supplying circuitry. 4.) The unit utilizes a Hirose H.FL connector and stated for use with approved antennas only. This fulfills the requirements of 15.203. 5.) The module was tested in a stand-alone configuration. The module complies with part 15 emissions limits regardless of the device into which it is eventually installed. 6.) The module has the FCC ID number permanently affixed and information supplied to the end user regarding label placement on the outside of the device into which the module is contained. This information is clearly defined in the user manual. 7.) The unit complies with part 15.247 as stated in the user manual. Adequate instructions are supplied with the unit to explain the requirements. 8.) The unit complies with the RF exposure requirements as stated in 2.1091, 2.1093, and part 15. Should you require any further information, please contact the undersigned. Thank you for your consideration in this matter. Sincerely, James W. Pearce

SECTION 5 EXTERNAL PHOTOGRAPHS FCC ID: QLBPT11MH U.S. Technologies, Inc. FCC Part 15,Class B Certification Report Number: 07-0186 Issue Date: August 9, 2007 Customer: Pegasus Technologies, Inc. Model: PT11MH PHOTOS OF THE TESTED EUT The following photos are attached: Photo 3 Top View of EUT with Shield in place FCC ID: QLBPT11MH U.S. Technologies, Inc. FCC Part 15,Class B Certification Report Number: 07-0186 Issue Date: August 9, 2007 Customer: Pegasus Technologies, Inc. Model: PT11MH Photo 3 Top View of EUT with shield in place

FCC ID: QLBPT11MH U.S. Technologies, Inc. FCC Part 15,Class B Certification Report Number: 07-0186 Issue Date: August 9, 2007 Customer: Pegasus Technologies, Inc. Model: PT11MH Photo 4 Label Location

SECTION 5 INTERNAL PHOTOGRAPHS FCC ID: QLBPT11MH U.S. Technologies, Inc. FCC Part 15,Class B Certification Report Number: 07-0186 Issue Date: August 9, 2007 Customer: Pegasus Technologies, Inc. Model: PT11MH PHOTOS OF THE TESTED EUT The following photos are attached: Photo 1 Top View of EUT Photo 2 Bottom View of EUT FCC ID: QLBPT11MH U.S. Technologies, Inc. FCC Part 15,Class B Certification Report Number: 07-0186 Issue Date: August 9, 2007 Customer: Pegasus Technologies, Inc. Model: PT11MH Photo 1. Top View of EUT FCC ID: QLBPT11MH U.S. Technologies, Inc. FCC Part 15,Class B Certification Report Number: 07-0186 Issue Date: August 9, 2007 Customer: Pegasus Technologies, Inc. Model: PT11MH Photo 2 Bottom View of EUT

FCC ID: QLBPT11MH U.S. Technologies, Inc. FCC Part 15,Class B Certification Report Number: 07-0186 Issue Date: August 9, 2007 Customer: Pegasus Technologies, Inc. Model: PT11MH SECTION 9 RF EXPOSURE INFORMATION FCC ID: QLBPT11MH U.S. Technologies, Inc. FCC Part 15,Class B Certification Report Number: 07-0186 Issue Date: August 9, 2007 Customer: Pegasus Technologies, Inc. Model: PT11MH 5.1 RF Safety Requirements to 2.1091 for Mobile Transmitters The unit under evaluation has one external antenna. Pegasus Technologies, Inc. calculated the MPE emission values for the EUT with this 1.2 dBi antenna. They used the formula shown in OET Bulletin 65 and calculated the minimum distance between antenna and unsuspecting user as 20 cm. Pegasus Technologies, Inc. will sell the PT11MH with the following antenna. MANUFACTURER TYPE OF ANTENNA MODEL GAIN dB TYPE OR CONNECTOR Mobile Antennas Pegasus Technologies, Inc. Monopole ¼ Wave Approximately 1.2 dBi Reverse Polarity SMA connector Power Output The EUT’s maximum expected output power as shown in Section 2.7 was Frequency of Fundamental (MHz) Measurement (dBm)* Measurement (mW)* FCC Limit (Watt) 902.952 27.16 520 1.0 915.020 27.37 546 1.0 926.950 27.06 508 1.0 * Measurement includes 0.1 dB for cable loss The maximum EIRP expected for mobile installations is with the +1.2 dBi gain Monopole antenna. This would yield a maximum EIRP of 27.37 dBm + 2.0 dBi = +29.57 dBm. FCC ID: QLBPT11MH U.S. Technologies, Inc. FCC Part 15,Class B Certification Report Number: 07-0186 Issue Date: August 9, 2007 Customer: Pegasus Technologies, Inc. Model: PT11MH 5.1 RF Safety Requirements to 2.1091 for Mobile Transmitters The maximum EIRP for mobile installations may be expected to be Antilog (29.57 dBm/10) = 905.73 mW MPE Calculations The limits for this unit (uncontrolled exposure) are 1.0 mW/cm 2 . Taking the RF Denisty Field Equation: Mobile Installations S = 905.73/4*π* 20 2 S = 905.73/5026.55 S = 0.18 mW / cm 2 This is well below the maximum level of 1.0 mW / cm 2 All manual instructions will specify 20 cm for mobile installations

Page 1 of 68 Pegasus Technologies, Inc. FCC Part 15, Certification Application PT11MH UST Project: 07-0186 Issue Date: August 17, 2007 3505 Francis Circle Alpharetta, GA 30004 PH: 770-740-0717 Fax: 770-740-1508 www.ustech-lab.com Page 2 of 68 I certify that I am authorized to sign for the manufacturer and that all of the statements in this report and in the Exhibits attached hereto are true and correct to the best of my knowledge and belief: UNITED STATES TECHNOLOGIES, INC. (AGENT RESPONSIBLE FOR TEST): By: Name: Louis A. Feudi __________ Title: VP / Operations & Engineering Date: August 17, 2007 _ Pegasus Technologies, Inc. 108 Pawnook Farm Road Lenoir City, TN 37771 By: ____________________ Name: __________________ Title: ___________________ Date: ___________________ This report shall not be reproduced except in full. This report may be copied in part only with the prior written approval of U.S. Technologies. The results contained in this report are subject to the adequacy and representative character of the sample provided. 3505 Francis Circle Alpharetta, GA 30004 PH: 770-740-0717 Fax: 770-740-1508 www.ustech-lab.com FCC ID: QLBPT11MH U.S. Technologies, Inc. FCC Part 15, Class B Certification Report Number: 07-0186 Issue Date: August 9, 2007 Customer: Pegasus Technologies, Inc. Model: PT11MH Page 3 of 68 MEASUREMENT/TECHNICAL REPORT This report concerns (check one): Original grant X Class II change_____ Equipment type: Spread-Spectrum Frequency Hopping RF modem that operates in the 902-928 MHz ISM band Deferred grant requested per 47 CFR 0.457(d)(1)(ii)? yes_____ No X If yes, defer until:_________________ date N.A. agrees to notify the Commission by N.A. date of the intended date of announcement of the product so that the grant can be issued on that date. Report prepared by: United States Technologies, Inc. 3505 Francis Circle Alpharetta, GA 30004 Phone Number: (770) 740-0717 Fax Number: (770) 740-1508 FCC ID: QLBPT11MH U.S. Technologies, Inc. FCC Part 15, Class B Certification Report Number: 07-0186 Issue Date: August 9, 2007 Customer: Pegasus Technologies, Inc. Model: PT11MH Page 4 of 68 TABLE OF CONTENTS SECTION 1 GENERAL INFORMATION 1.1 Product Description 1.2 Related Submittal(s) SECTION 2 TESTS AND MEASUREMENTS 2.1 Configuration of Tested EUT 2.2 Test Facility 2.3 Test Equipment 2.4 Modifications 2.5 Test Procedure and Results 2.6 Antenna Description 2.7 Peak Power (Bandedge Antenna Conducted at Antenna Terminal) 2.8 Antenna Conducted Spurious Emissions 2.9 Peak Radiated Spurious Emissions 2.10 Average Radiated Spurious Emissions 2.11 Bandedge Requirements 2.12 Minimum 20 dB Bandwidth 2.13 Number of Hopping Channels 2.14 Average Time of Occupancy per Channel 2.15 Power Line Conducted Emissions for Transmitter 2.16 Radiated Emissions for Digital Device & Receiver (47 CFR 15.109a) 2.17 Power Line Conducted Emissions for Digital Device and Receiver FCC Section 15.107 2.18 Channel Separation SECTION 3 LABELING INFORMATION SECTION 4 BLOCK DIAGRAM(S)/ SCHEMATIC(S) SECTION 5 PHOTOGRAPHS SECTION 6 THEORY OF OPERATION SECTION 7 TUNE UP PROCEDURE SECTION 8 USER'S MANUAL SECTION 9 RF EXPOSURE INFO FCC ID: QLBPT11MH U.S. Technologies, Inc. FCC Part 15, Class B Certification Report Number: 07-0186 Issue Date: August 9, 2007 Customer: Pegasus Technologies, Inc. Model: PT11MH Page 5 of 68 LIST OF FIGURES AND TABLES FIGURES 1) Test Configuration 2) Photograph(s) for Spurious and Conducted Emissions 3) Peak Output Power 4) Conducted Spurious Emissions 5) Peak Radiated Spurious Emissions 6) Bandedge Compliance Antenna Conducted 7) 20 dB Bandwidth 8) Number of Hopping Channels 9) Average Time of Occupancy 10) Channel Separation TABLES 1) EUT and Peripherals 2) Test Instruments 3) Peak Power Output 4) Peak Radiated Spurious Emissions 5) Average Radiated Spurious Emissions 6) 20 dB Bandwidth 7) Number of Hopping Channels 8) Conducted Emissions 9) Radiated Emissions for Digital Device and Receiver 10) Channel Separation FCC ID: QLBPT11MH U.S. Technologies, Inc. FCC Part 15, Class B Certification Report Number: 07-0186 Issue Date: August 9, 2007 Customer: Pegasus Technologies, Inc. Model: PT11MH Page 6 of 68 SECTION 1 GENERAL INFORMATION FCC ID: QLBPT11MH U.S. Technologies, Inc. FCC Part 15, Class B Certification Report Number: 07-0186 Issue Date: August 9, 2007 Customer: Pegasus Technologies, Inc. Model: PT11MH Page 7 of 68 GENERAL INFORMATION 1.1 Product Description The Equipment Under Test (EUT) is the Pegasus Technologies, Inc. PT11MH. The EUT is a Spread-Spectrum Frequency Hopping Data Transceiver Module operating in the 902-928 MHz ISM band. FCC ID: QLBPT11MH U.S. Technologies, Inc. FCC Part 15, Class B Certification Report Number: 07-0186 Issue Date: August 9, 2007 Customer: Pegasus Technologies, Inc. Model: PT11MH Page 8 of 68 1.2 Related Submittal(s)/Grant(s) The EUT will be used to send/receive data. The transceiver presented in this report will be used with other like transceivers: The EUT is subject to the following authorizations: a) Certification as a transceiver (modular approval) b) Verification as a digital device The information contained in this report is presented for the certification & verification authorization(s) for the EUT. The manufacturer desires to seek a modular approval on this device. FCC ID: QLBPT11MH U.S. Technologies, Inc. FCC Part 15, Class B Certification Report Number: 07-0186 Issue Date: August 9, 2007 Customer: Pegasus Technologies, Inc. Model: PT11MH Page 9 of 68 SECTION 2 TESTS AND MEASUREMENTS FCC ID: QLBPT11MH U.S. Technologies, Inc. FCC Part 15, Class B Certification Report Number: 07-0186 Issue Date: August 9, 2007 Customer: Pegasus Technologies, Inc. Model: PT11MH Page 10 of 68 TEST AND MEASUREMENTS 2.1 Configuration of Tested System The sample was tested per ANSI C63.4, Methods of Measurement from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz (2003). Conducted and radiated emissions data were taken with the test receiver…

Text truncated - open the document above for the full version.

FCC ID: QLBPT11MH U.S. Technologie s, Inc. FCC Part 15, Class B Certification Report Number: 07-0186 Issue Date: August 9, 2007 Customer: Pegasus Technologies, Inc. Model: PT11MH FIGURE 2a Photograph(s) for Spurious Emissions FCC ID: QLBPT11MH U.S. Technologie s, Inc. FCC Part 15, Class B Certification Report Number: 07-0186 Issue Date: August 9, 2007 Customer: Pegasus Technologies, Inc. Model: PT11MH FIGURE 2b Photograph(s) for Spurious Emissions FCC ID: QLBPT11MH U.S. Technologie s, Inc. FCC Part 15, Class B Certification Report Number: 07-0186 Issue Date: August 9, 2007 Customer: Pegasus Technologies, Inc. Model: PT11MH FIGURE 2c Photograph(s) for Conducted Emissions Not Applicable EUT is Battery Operated