QLHQAB0802Bluetooth Dongle

BlueTooth Dongle User’s Guide 1 CHAPTER ONE INTRODUCTION TO BLUETOOTH_______________________________ 4 INTRODUCTION TO BLUETOOTH FOR WINDOWS____ 4 Most Bluetooth-enabled devices have the capability to act as __________________________________ 4 Bluetooth for Windows provides _______________ 5 Bluetooth for Windows supports _______________ 5 BLUETOOTH DEVICE IDENTITY_________________ 5 Device Icons for Windows 9x, ME and 2K _______ 5 Device Icons for Windows XP ________________ 5 Service Icons for Windows 9x, ME and 2K ______ 6 Service Icons for Windows XP ________________ 6 CHAPTER TWO INSTALLATION _____________ 7 INSTALLING BLUETOOTH FOR WINDOWS (BTW) ___ 7 SYSTEM REQUIREMENTS ________________ 7 UNINSTALL PREVIOUS VERSION OF BTW __ 7 INSTALL BTW ___________________________ 8 Install Shield Wizard ________________________ 8 Install Shield Wizard Screen Shots _____________ 9 CHAPTER THREE BASIC OPERATIONS _____ 13 STA RT PROGRAM__________________________ 13 way 1 _________________________________ 13 way 2 _________________________________ 13 FIND BLUETOOTH DEVICES__________________ 13 Periodic Search for Devices _______________ 14 Some devices within connection range may not show up in the list of devices found because _________ 14 FIND A SERVICE___________________________ 15 BLUETOOTH CONNECTION STAT U S_____________ 16 Display the Connection Status dialog box_______ 16 Information provided is _____________________ 16 The controls in the Bluetooth Connection Status dialog box are ____________________________ 17 BLUETOOTH CONNECTION WIZARD____________ 17 Setup a new connection _____________________ 17 BLUETOOTH TRAY__________________________ 19 From BTTray you can: ______________________ 19 SEND TO BLUETOOTH_______________________ 20 To use Send to Bluetooth ____________________ 20 CHAPTER FOUR CLIENT APPLIANCE _______ 21 NETWORK ACCESS_________________________ 21 Possible Network Access servers include _______ 21 Network Access Setup for Windows 2000 _____ 21 Network Access Setup for Windows 98SE & Windows Me____________________________ 22 Configure the routing software: _______________ 22 BLUETOOTH SERIAL PORT____________________ 22 To establish a Bluetooth serial port connection ___ 23 Determine the communications port being used by the server ___________________________________ 24 Close a Bluetooth serial port connection ________ 24 DIAL-UP NETWORKING______________________ 25 Establish a Dial-up Networking session_________ 25 Close a Dial-up Networking connection ________ 26 FAX_____________________________________ 26 Send a Fax _______________________________ 26 FILE TRANSFER____________________________ 27 Perform an operation on a folder or file _________ 27 Types of File Transfer operations ______________ 28 Other options that may appear ________________ 28 INFORMATION EXCHANGE____________________ 29 Supported Outlook items are _________________ 29 There are three types of operation _____________ 29 Send, receive or exchange an object ___________ 29 SERVICES_________________________________ 29 Determine the services provided by a Bluetooth device ___________________________________ 30 CHAPTER FIVE LOCAL SERVICES __________ 31 The services provided by Bluetooth for Windows are ___________________________________ 31 Stop a local service ______________________ 31 BlueTooth Dongle User’s Guide 2 Interrupt a connection from the server side ___ 32 CHAPTER SIX CONFIGURATION PANEL ____ 33 Access the Bluetooth Configuration Panel ____ 33 ACCESSIBILITY TAB________________________ 33 Accessibility Configuration Settings _________ 33 Allow other devices to discover this computer ___ 33 Control the types of devices that are allowed to connect to this computer ____________________ 34 Accessibility, Adding and Deleting Devices ___ 34 Limit access to your computer to specific remote devices __________________________________ 34 Add a device to the list of devices allowed to connect ________________________________________ 34 Delete a device from the list of devices allowed to connect __________________________________ 35 DISCOVERY TAB___________________________ 35 Discovery Configuration Settings ___________ 35 Periodic Search for Devices__________________ 35 Determine the devices that will be reported _____ 36 Discovery, Adding Specific Devices _________ 36 Limit the type of remote devices reported _______ 36 Report only specific devices _________________ 36 Report only a specific class of device __________ 37 Report only a specific a type of device within a class ________________________________________ 37 Discovery, Deleting Specific Devices ________ 37 Remove a device from the list of devices to be discovered _______________________________ 37 Temporarily override the discovery of specific devices __________________________________ 37 GENERAL CONFIGURATION SETTINGS___________ 38 HARDWARE CONFIGURATION_________________ 38 PLUG IN DONGLE__________________________ 39 Hardware Advanced Settings Dialog Box _____ 40 INFORMATION EXCHANGE CONFIGURATION SETTINGS ________________________________________ 41 File Transfer______________________________ 41 Send Business Card ________________________ 41 Receive Business Card ______________________ 42 LOCAL SERVICES TAB_______________________ 42 Local Services Configuration Settings________ 42 Bluetooth for Windows Local Service Names ____ 42 Property settings which are common to all of the local services __________________________________ 43 Some local services have additional property settings ________________________________________ 43 NOTIFICATIONS TAB________________________ 43 Notifications Configuration Settings _________ 43 Associate a sound with a Bluetooth event _______ 44 CHAPTER SEVEN SECURITY _______________ 45 SECURITY INTRODUCTION____________________ 45 AUTHENTICATION__________________________ 45 AUTHORIZATION___________________________ 45 ENCRYPTION______________________________ 46 LEVELS OF SECURITY_______________________ 46 The configuration…

Text truncated - open the document above for the full version.

1. 1. BLOCK DIAGRAM BLOCK DIAGRAM Flash Memory Flash Memory 256K x 16 bit 256K x 16 bit 4Mbit 4Mbit Balun Balun BPF BPF 2.4 2.4 GHz GHz Radio Radio I/O I/O RAM RAM DSP DSP uP uP BlueCore BlueCore 02 02 I/O I/O 16 16 MHz MHz Crystal Crystal TX/RX TX/RX Power Power USB USB 接頭 接頭 接頭 接頭 接頭 接頭 接頭 接頭 介 介 介 介 介 介 介 介 面 面 面 面 面 面 面 面 天線 天線 天線 天線 天線 天線 天線 天線

Subject: Re: EPoX COMPUTER CO., LTD. FCC ID:QLHQAB0802, AN02T2198 Hi Mike, Please find the attached is Power Spectral Density Test. ----- Original Message ----- From: "Mike Kuo" <[email protected]> Subject: RE: EPoX COMPUTER CO., LTD. FCC ID:QLHQAB0802, AN02T2198 > When Bluetooth Device is in the acquisition mode, it is acting as direct > sequence spread spectrum. For all bluetooth device, power spectra density > test is required. > > M.Kuo > > -----Original Message----- > > > > > Hi Mike, > > > > Reply question 1: Please find the attached is Spruious radiated emission > > test report update. The RBW and VBW is 100KHz. > > > > About question 2: Base 15.247(f) requirement: Hybrid systems are those > that > > employ a combination of both FHSS and DSSS. This device is bluetooth. not > > hybrid system. Should I provide Power Density test data? > > > > I had upload the External photos, FCC ID Label and revised user's manual > on > > 8/30. If you didn't receive them, please tell me. > > > > By the way, so if you have any question, please email to me. > > Thanks. > > Eva > > > > > > > > > Subject: FW: EPoX COMPUTER CO., LTD. FCC ID:QLHQAB0802, AN02T2198 > > > > > > > > > > > > > > > > > > -----Original Message----- > > > > From: CERTADM > > > > Sent: Monday, August 26, 2002 5:59 PM > > > > To: '[email protected]' > > > > Subject: EPoX COMPUTER CO., LTD. FCC ID:QLHQAB0802, AN02T2198 > > > > > > > > > > > > Notice_content > > > > ------------- > > > > Question #1: What is the RBW and VBW used during Spurious Radiated > > > emission > > > > tests below 1GHz. > > > > > > > > Question #2: Please provide Power Spectra Density Test data when the > > > device > > > > is in Acquisition mode per 15.247(f) requirements. > > > > > > > > Question #3: Please provide External Photos > > > > > > > > Question #4: Please provide FCC ID label format and proposed location. > > > > > > > > Question #5: The user manual does not contain RF exposure warning > > > statement. > > > > Suggest wording to be included in the user manual for this type of > > device > > > is > > > > following: > > > > > > > > :IMPORTANT NOTICE: To comply with FCC RF exposure compliance > > requirements, > > > > this device and its antenna must not be co-located or operating in > > > > conjunction with any other antenna or transmitter. Do not modify the > > > device > > > > or its antenna. Any unauthorized changes to the device may avoid the > > > user's > > > > authorities to operate this device. > > > > > > > > Question #6: The user manual does not contain information required > under > > > > section 15.21 and 15.105(b). Please provide revised user manual. > > > > > > > > Best Regards > > > > > > > > Mike Kuo / TCB Certifier > > > > The items indicated above must be submitted before processing can > > continue > > > > on the above referenced application. Failure to provide the requested > > > > information within 60 days of the original e-mail date may result in > > > > application dismissal and forfeiture of the filing fee. Also, please > > note > > > > that partial responses increase processing time and should not be > > > submitted. > > > > Any questions about the content of this correspondence should be > > directed > > > to > > > > the e-mail address listed below the name of the sender. > > > >

Bluetooth Declaration Per FCC 15.247 Requirements 1 Output power and channel separation of a Bluetooth device in the different operating modes: The different operating modes (data-mode, acquisition-mode) of a Bluetooth device don’t influence the output power and the channel spacing. There is only one transmitter which is driven by identical input parameters concerning these two parameters. Only a different hopping sequence will be used. For this reason the check of these RF parameters in one op-mode is sufficient. 2 Frequency range of a Bluetooth device: Hereby we declare that the maximum frequency of this device is: 2402 – 2480 MHz. This is according the Bluetooth Core Specification V 1.0B (+ critical errata) for devices which will be operated in the USA. This was checked during the Bluetooth Qualification tests (Test Case: TRM/CA/04-E). Other frequency ranges ( e.g. for Spain, France, Japan) which are allowed according the Core Specification are not supported by this device. 3 Co-ordination of the hopping sequence in data mode to avoid simultaneous occupancy by multiple transmitters: Bluetooth units which want to communicate with other units must be organized in a structure called piconet. This piconet consist of max. 8 Bluetooth units. One unit is the master the other seven are the slaves. The master co-ordinates frequency occupation in this piconet for all units. As the master hop sequence is derived from it’s BD address which is unique for every Bluetooth device, additional masters intending to establish new piconets will always use different hop sequences. 4 Example of a hopping sequence in data mode: Example of a 79 hopping sequence in data mode: 40, 21, 44, 23, 42, 53, 46, 55, 48, 33, 52, 35, 50, 65, 54, 67, 56, 37, 60, 39, 58, 69, 62, 71, 64, 25, 68, 27, 66, 57, 70, 59, 72, 29, 76, 31, 74, 61, 78, 63, 01, 41, 05, 43, 03, 73, 07, 75, 09, 45, 13, 47, 11, 77, 15, 00, 64, 49, 66, 53, 68, 02, 70, 06, 01, 51, 03, 55, 05, 04 5 Equally average use of frequencies in data mode and behaviour for short transmissions: The generation of the hopping sequence in connection mode depends essentially on two input values: 1. LAP/UAP of the master of the connection 2. Internal master clock The LAP (lower address part) are the 24 LSB’s of the 48 BD_ADDRESS. The BD_ADDRESS is an unambiguous number of every Bluetooth unit. The UAP (upper address part) are the 24 MSB’s of the 48 BD_ADDRESS. The internal clock of a Bluetooth unit is derived from a free running clock which is never adjusted and is never turned off. For synchronisation with other units only offset are used. It has no relation to the time of the day. Its resolution is at least half the RX/TX slot length of 312.5 μs. The clock has a cycle of about one day (23h30). In most case it is implemented as 28 bit counter. For the deriving of the hopping sequence the entire LAP (24 bits), 4 LSB’s (4 bits) (Input 1) and the 27 MSB’s of the clock (Input 2) are used. With this input values different mathematical procedures (permutations, additions, XOR-operations) are performed to generate the sequence. This will be done at the beginning of every new transmission. Regarding short transmissions the Bluetooth system has the following behaviors: The first connection between the two devices is established, a hopping sequence was generated. For transmitting the wanted data the complete hopping sequence was not used. The connection ended. The second connection will be established. A new hopping sequence is generated. Due to the fact that the Bluetooth clock has a different value, because the period between the two transmission is longer (and it cannot be shorter) than the minimum resolution of the clock (312.5 μs). The hopping sequence will always differ from the first one. 6 Receiver input bandwidth and behaviors for repeated single or multiple packets: The input bandwidth of the receiver is 1 MHz. In every connection one Bluetooth device is the master and the other one is the slave. The master determines the hopping sequence (see chapter 5). The slave follows this sequence. Both devices shift between RX and TX time slot according to the clock of the master. Additionally the type of connection (e.g. single or multislot packet) is set up at the beginning of the connection. The master adapts its hopping frequency and its TX/RX timing according to the packet type of the connection. Also the slave of the connection will use these settings. Repeating of a packet has no influence on the hopping sequence. The hopping sequence generated by the master of the connection will be followed in any case. That means, a repeated packet will not be send on the same frequency, it is send on the next frequency of the hopping sequence. 7 Dwell time in data mode The dwell time of 0.3797s within a 30 second period in data mode is independent from the packet type (packet length). The calculation for a 30 second period is a follows: Dwell time = time slot length * hop rate / number of hopping channels *30s Example for a DH1 packet (with a maximum length of one time slot) Dwell time = 625 μs * 1600 1/s / 79 * 30s = 0.3797s (in a 30s period) For multislot packet the hopping is reduced according to the length of the packet. Example for a DH5 packet (with a maximum length of five time slots) Dwell time = 5 * 625 μs * 1600 * 1/5 *1/s / 79 * 30s = 0.3797s (in a 30s period) This is according the Bluetooth Core Specification V 1.0B (+ critical errata) for all Bluetooth devices. There for all Bluetooth devices comply with the FCC dwell time requirement in data mode. This was checked during the Bluetooth Qualification tests. The Dwell time in hybrid mode is measured and stated in the test report. 8 Channel Separation in hybrid mode The nominal channel spacing of the Bluetooth system is 1Mhz independent of the operating mode. The maximum “initial carrier frequency tolerance” which is allowed for Bluetooth is fcenter = 75 kHz. This was checked during the Bluetooth Qualification tests (Test Case:…

Text truncated - open the document above for the full version.

Page1 Rev. 00 APPENDIX 2 External Photos of EUT C&C Laboratory Co. Ltd. REPORT NO: 020034-RF-ID FCC ID: QLHQAB0802 DATE: 08/06/2002 Page2 Rev. 00 Front View of EUT Back View of EUT

FCC ID LABEL FORMAT AND LOCATION Applicant: EpoX COMPUTER CO., LTD. FCC ID: QLHQAB0802 寬 20mm*高 15mm FCC ID: QLHQAB0802 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID LABEL AREA 寬 20mm*高 15mm Model No：BT-DG02 Bluetooth USB Dongle FCC ID ： xxxxxxxxxxxxxxx Test To Comply With Standards FOR HOME OR OFFICE USE 檢磁： xxxxxxxx Made in Taiwan 電波：xxxxxxxxx

Page 8 Rev. 00 APPENDIX 3 Internal Photos of EUT Page 9 Rev. 00 Internal of EUT - Front Page 10 Rev. 00 Internal of EUT - Back

Integrated Miniaturized Antenna for 2.4 GHz Wireless RF Applications TCA10F is an advanced, surface-TCA10F is an advanced, surface- mount(SMT) integrated antenna formount(SMT) integrated antenna for use in various wireless RF motheruse in various wireless RF mother boards, ideal for high-sensitivity,boards, ideal for high-sensitivity, low profile design.low profile design. Features: Outline of TCA10F (unit:mm) Typical SMT Installation Layout Guide (unit:mm) Preliminary Ver 5.3 9/13/2000 Product Information 1/2 Specification •Part No.TCA10F •Center Frequency2450MHz •Band width300MHz •Peak Gain3dBi •Typical Gain2dBi •Operating Temp.-20 o C~70 o C •Storage Temp.-20 o C~90 o C •Weight 0.6g •Miniaturized size •Omni-direction •Low interference design •Wide bandwidth •Light weight •High gain TCA10F TCA10F Preliminary Ver 5.3 9/13/2000 Smith Chart CH1 S 11 1 U FS START 1 500.000 000 MHzSTOP 3 500.000 000 MHz Cor MARKER 1 2.44 GHz 22 Feb 2000 13:51:25 1 1_: 44.236 -13.779 4.7337 pF 2 440.000 000 MHz CH1 S 11 SWR1 /REF 1 START 1 500.000 000 MHzSTOP 3 500.000 000 MHz Cor MARKER 1 2.44 GHz 22 Feb 2000 13:51:54 1 1_: 1.3969 2 440.000 000 MHz H-Plane E-Plane VSWR Measured Antenna Patterns at 2.4GHz (under test condition 1) Typical Input Characteristics TriCOME Microwave Electronics Corp. 3-5F, No. 31, Ln. 216, Gung Yuan Rd., Hsin Chu, Taiwan TEL: +886-3-561-3662 FAX: +886-3-561-0416 E-mail: [email protected] 2/2 This specification , prepared by TriCOME , is believed to be accurate and reliable . But TriCOME reserves the right to make any change or improvement without further notice. Printed in Taiwan 0 45 90 135 180 225 270 315 0 0 -5 -5 -10 -10 -15 -15 -20 -20 -25 -25 -30 -30-35

C&C Laboratory Co. Ltd. REPORT NO: 020034-RF-ID FCC ID: QLHQAB0802 DATE: 08/06/2002 Page 68 Rev. 01 13. Peak Power Spectral Density 13.1 Standard Applicable According to 15.247(d), for direct sequence systems, the peak power spectral density conducted from the intentional radiator to the antenna shall not be greater than 8 dBm in any 3kHz band during any time interval of continuous transmission. 13.2 Measurement Procedure 1. Place the EUT on the table and set it in transmitting mode. 2. Remove the antenna from the EUT and then connect a low loss RF cable from the antenna port to the spectrum analyzer. 3. Set the spectrum analyzer as RBW = 3KHz, VBW = auto, Span = 300KHz, Sweep=1s 4. Record the max. reading. 5. Repeat above procedures until all frequency measured were complete. 13.3 Measurement Result 13.4 Measurement Equipment Used: EQUIPMENT TYPE MFR Model No. Serial No. LAST CAL. Cal. Due. Spectrum Analyzer ADVANTEST R3271A NA 10/15/2001 10/14/2002 Plotter HP 7475A 2938A29027N/A N/A low loss cable Huber + Suhner Sucoflex 104N/A N/A N/A CHFrequencyRF Power Density Maximum Limit Result (MHz)(dBm)(dBm) Low-9.418PASS Mi d-8.368PASS High -9.428PASS C&C Laboratory Co. Ltd. REPORT NO: 020034-RF-ID FCC ID: QLHQAB0802 DATE: 08/06/2002 Page 69 Rev. 01 Power Spectral Density Test Plot (CH-Low) C&C Laboratory Co. Ltd. REPORT NO: 020034-RF-ID FCC ID: QLHQAB0802 DATE: 08/06/2002 Page 70 Rev. 01 Power Spectral Density Test Plot (CH-Mid) C&C Laboratory Co. Ltd. REPORT NO: 020034-RF-ID FCC ID: QLHQAB0802 DATE: 08/06/2002 Page 71 Rev. 01 Power Spectral Density Test Plot (CH-High)

C&C Laboratory Co. Ltd. REPORT NO: 020034-RF-ID FCC ID: QLHQAB0802 DATE: 08/06/2002 Page 39 Rev. 00 9. SPURIOUS RADIATED EMISSION TEST 9.1 Standard Applicable According to 15.247(c), all other emissions outside these bands shall not exceed the general radiated emission limits specified in 15.209(a). And according to 15.33(a)(1), for an intentional radiator op- erates below 10GHz, the frequency range of measurements: to the tenth harmonic of the highest funda- mental frequency or to 40GHz, whichever is lower. 9.2 EUT Setup 1. The radiated emission tests were performed in the 3 meter open-test site, using the setup in ac- cordance with the ANSI C63.4-1992. 2. The EUT was put in the front of the test table. The host PC system was placed on the center of the back edge on the test table. The peripherals like modem, monitor printer, K/B, and mouse were placed on the side of the host PC system. The rear of the EUT and peripherals were placed flushed with the rear of the tabletop. 3. The keyboard was placed directly in the front of the monitor, flushed with the front tabletop. The mouse was placed next to the Keyboard, flushed with the back of keyboard. 4. The spacing between the peripherals was 10 centimeters. 5. External I/O cables were draped along the edge of the test table and bundle when necessary. 6. The host PC system was connected with 110Vac/60Hz power source. 9.3 Measurement Procedure 1. The EUT was placed on a turn table which is 0.8m above ground plane. 2. The turn table shall rotate 360 degrees to determine the position of maximum emission level. 3. EUT is set 3m away from the receiving antenna which varied from 1m to 4m to find out the highest emissions. 4. Maximum procedure was performed on the six highest emissions to ensure EUT compliance. 5. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. 6. Repeat above procedures until all frequency measured were complete. C&C Laboratory Co. Ltd. REPORT NO: 020034-RF-ID FCC ID: QLHQAB0802 DATE: 08/06/2002 Page 40 Rev. 00 9.4 Test SET-UP (Block Diagram of Configuration) (A) Radiated Emission Test Set-Up, Frequency Below 1000MHz (B) Radiated Emission Test Set-UP Frequency Over 1 GHz 1m to 4m Spectrum Analyzer EUT 3m 1m Turntable Coaxial Cable Ground Plane Test Receiver EUT 3m 1m to 4m Turntable Coaxial Cable Ground Plane 1 m C&C Laboratory Co. Ltd. REPORT NO: 020034-RF-ID FCC ID: QLHQAB0802 DATE: 08/06/2002 Page 41 Rev. 00 9.5 Measurement Equipment Used: Open Area Test Site # 3 EQUIPMENT TYPE MFR MODEL NUMBER SERIAL NUMBER LAST CAL. CAL DUE. Spectrum Analyzer ADVANTEST R3261A N/A 03/19/2002 03/18/2003 EMI Test Receiver R&S ESVS20 838804/004 01/05/2002 01/04/2003 Pre-Amplifier HP 8447D 2944A09173 03/04/2002 03/03/2003 Bilog Antenna SCHWAZBECKVULB9163 145 07/06/2002 07/05/2003 Turn Table EMCO 2081-1.21 9709-1885 N.C.R N.C.R Antenna Tower EMCO 2075-2 9707-2060 N.C.R N.C.R Controller EMCO 2090 9709-1256 N.C.R N.C.R RF Switch ANRITSU MP59B M53867 N.C.R N.C.R Site NSA C&C N/A N/A 11/17/2001 11/16/2002 Horn antenna Schwarzbeck BBHA 9120D210 2/24/2002 2/23/2003 Pre-Amplifier HP 8449B 3008B00965 10/01/2001 10/02/2002 9.6 Field Strength Calculation The field strength is calculated by adding the Antenna Factor and Cable Factor and subtracting the Amplifier Gain and Duty Cycle Correction Factor(if any) from the measured reading. The basic equa- tion with a sample calculation is as follows: FS = RA + AF + CL - AG Where FS = Field Strength CL = Cable Attenuation Factor (Cable Loss) RA = Reading Amplitude AG = Amplifier Gain AF = Antenna Factor 9.7 Measurement Result (below 1GHz) Refer to attach tabular data sheets. NOTE: The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 100kHz for Peak detection (PK) and Quasi-peak detection (QP) at frequency below 1GHz.

C&C Laboratory Co. Ltd. REPORT NO: 020034-RF-ID FCC ID: QLHQAB0802 DATE: 08/06/2002 Page 1 of 70 Rev. 00 ELECTROMAGNETIC EMISSIONS COMPLIANCE REPORT INTENTIONAL RADIATOR CERTIFICATION TO FCC PART 15 SUBPART C REQUIREMENT OF Bluetooth Dongle MODEL No.: BT-DG02 BRAND NAME: EPoX FCC ID: QLHQAB0802 REPORT NO: 020034-RF-ID ISSUE DATE: Aug 6, 2002 Prepared for EPoX COMPUTER CO., LTD. 10Fl, 346, Chung San Road, Sec. 2, Chung Ho City, Taipei Hsien, 235 Taiwan, R. O. C. Prepared by C&C LABORATORY, CO., LTD. #B1, 1 st Fl., Universal Center, No. 183, Sec. 1, Tatung Rd., Hsi Chih, Taipei Hsien, Taiwan, R.O.C. TEL: (02)8642-2071~3 FAX: (02) 8642-2256 C&C Laboratory Co. Ltd. REPORT NO: 020034-RF-ID FCC ID: QLHQAB0802 DATE: 08/06/2002 Page 2 Rev. 00 VERIFICATION OF COMPLIANCE Applicant: EPoX Computer Co., Ltd. 10Fl, 346, Chung San Rd., Sec. 2, Chung Ho City, Taipei Hsien, 235 Taiwan, R.O.C. Equipment Under Test: Bluetooth Dongle BRAND NAME: EPoX MODEL No.: BT-DG02 Serial Number: N/A File Number: 020034-RF-ID Date of test: July 29 ~ Aug. 2, 2000 We hereby certify that: The above equipment was tested by C&C Laboratory Co., Ltd. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4 (1992) and the energy emitted by the sample EUT tested as described in this report is in compliance with conducted and radiated emission limits of FCC Rules Part 15. The test results of this report relate only to the tested sample identified in this report. Approved By Steven Wang / RF Dept. Manager C&C Laboratory Co., Ltd C&C Laboratory Co. Ltd. REPORT NO: 020034-RF-ID FCC ID: QLHQAB0802 DATE: 08/06/2002 Page 3 Rev. 00 Table of Contents 1. GENERAL INFORMATION .........................................................................................................5 1.1 Product Description ............................................................................................................................5 1.2 Related Submittal(s) / Grant (s) ..........................................................................................................5 1.3 Test Methodology ...............................................................................................................................5 1.4 Test Facility.........................................................................................................................................5 1.5 Special Accessories .............................................................................................................................5 1.6 Equipment Modifications....................................................................................................................5 2. SYSTEM TEST CONFIGURATION ............................................................................................6 2.1 EUT Configuration .............................................................................................................................6 2.2 EUT Exercise ......................................................................................................................................6 2.3 Test Procedure.....................................................................................................................................6 2.4 Configuration of Tested System..........................................................................................................7 3. SUMMARY OF TEST RESULTS ...............................................................................................10 4. DESCRIPTION OF TEST MODES ............................................................................................10 5. CONDUCTED EMISSION TEST................................................................................................11 5.1 Standard Applicable ..........................................................................................................................11 5.2 EUT Setup.........................................................................................................................................11 5.3 Measurement Procedure....................................................................................................................11 5.4 Measurement Equipment Used: ........................................................................................................12 5.5 Measurement Result..........................................................................................................................12 6. PEAK OUTPUT POWER MEASUREMENT............................................................................31 6.1 Standard Applicable ..........................................................................................................................31 6.2 Measurement Procedure....................................................................................................................31 6.3 Measurement Result..........................................................................................................................31 6.4 Measurement Equipment Used: ........................................................................................................31 7. 20dB BAND WIDTH .....................................................................................................................32 7.1 Standard Applicable ..........................................................................................................................32 7.2 Measurement Procedure....................................................................................................................32 7.3 Measurement Result..........................................................................................................................32 7.4 Measurement Equipment Used: ........................................................................................................32 8. 10…

Text truncated - open the document above for the full version.

C&C Laboratory Co. Ltd. REPORT NO: 020034-RF-ID FCC ID: QLHQAB0802 DATE: 08/06/2002 Page 36 Rev. 00 8. 100KHz BANDWIDTH OF BAND EDGES MEASUREMENT 8.1 Standard Applicable According to §15.247(c), in any 100 KHz bandwidth outside the frequency bands in which the spread spectrum intentional radiator in operat…

Text truncated - open the document above for the full version.