QQ6-BTR02Code Blue Core 4 Radio

BlueCore4 Radio User Manual -  Save Settngs Code Blue Core 4 Rado The Code Bluetooth Modem has been tested for compliance with FCC regulations and was found to be compliant with all applicable FCC Rules and Regulations. FCC#:QQ6-BTR02 IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, this device must not be co-located or operate in conjunction with any other antenna or transmitter. CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Model #: CR2AG-R0 V02 FCC ID#: QQ6-BTR02 Figure 1. Blue Core 4 Radio

Code Corporation - CONFIDENTIAL 11814 South Election Road, Suite 200, Draper, UT 84020 phone: (801) 495-2200 fax: (801) 495-2202 web: www.codecorp.com Date October 29, 2007 Federal Communications Commission Dear Application Examiner, Request For A Limited Modular Approval - FCC ID: QQ6-BTR02 The Code Corporation is seeking FCC authorization for the use of our Radio Modem CR2AG-R0-01-02 as a limited modular RF transmitter. The requirements of the FCC Public notice DA00-1407 are addressed as follows: 1. The Modular Transmitter must have its own RF shielding. The Radio Modem has its own RF shielding. 2. The Modular Transmitter must have buffered modulation/data inputs. The modulation/data inputs are buffered. 3. The Modular Transmitter must have its own power supply regulation. The Radio Modem requires a power supply specified at 3.3 VDC ± 0.1% 4. The Modular Transmitter must comply with the antenna requirements of Section 15.203 and 15.204c The antenna of this device is a 0 dBi Tyco antenna mounted on the printed circuit board of the Radio Modem and is not user replaceable. 5. The Modular Transmitter must be tested in a stand-alone configuration. The Radio Modem was tested in the requested “stand-alone” configuration. 6. The Modular Transmitter must be labeled with its own FCC ID number. The Radio Modem will be labeled with its own FCC ID number. The label as specified in the Radio Modem CR2AG-R0-01-02 Datasheet will be used. This module is only intended for use in products manufactured by The Code Corporation. An appropriate FCC label identifying the use of a limited modular device will be affixed to the final product. Code Corporation - CONFIDENTIAL 11814 South Election Road, Suite 200, Draper, UT 84020 phone: (801) 495-2200 fax: (801) 495-2202 web: www.codecorp.com 7. The Modular Transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. The Radio Modem is only intended for use in products manufactured by The Code Corporation. The Code Corporation will provide final instructions to the end user of the completed product which will include appropriate labeling and other FCC requirements. 8. The Modular Transmitter must comply with any applicable RF exposure requirements. The Radio Modem is only intended for use in products manufactured by The Code Corporation. The Code Corporation will provide the required distance either by the design of the final product into which the Radio Modem will be installed or by providing specific instructions to the end user regarding the minimum approved distance necessary to comply with this requirement. The maximum permissible exposure is defined in 47 CFR 1.1310 with 1 mW/cm 2 . The minimum permitted distance is calculated using the general equation: S = P*G/4ΠR 2 S = 1mW/cm 2 P = 44.7 mW ( From test report) G = 0 dBi or unity (1) Π = 3.1416 Solving for R, the minimum distance in cm is 1.88cm. Please contact us is you have any additional questions. Sincerely, Kevin Marriott Electrical Engineer Code Corporation

Component Side of PCB with RF Shield

Bluetooth-04 BD ADDR: Model #: CR2AG-R0 V2 000BEF000000 FCC ID: QQ6-BTR02

Component Side of PCB with RF Shield Component Side of PCB with RF Shield Removed Trace Side of PCB

FCC ID: QQ6-BTR02 Model Number CR2AG-R0-01-02 MAXIMUM PERMISSIBLE EXPOSURE (MPE) COMPUTATION FCC Part 1.1310 Maximum Permissible Exposure (MPE) Limits The EUT show compliance to the requirements of this section, which states the MPE limits for general population/ uncontrolled exposure are as shown below: Table 1-- Limits for General Population/Uncontrolled Exposure Frequency range (MHz) Electric field strength (V/m) Magnetic field strength (A/m) Power density (mW/cm\ 2 ) Averaging time (minutes) 0.3-1.34 614 1.63 *(100) 30 1.34-30 824/f 2.19/f *(180/f\ 2 ) 30 30-300 27.5 0.073 0.2 30 300-1500 - - f/1500 30 1500-100,000 - - 1.0 30 f = frequency in MHz * = Plane-wave equivalent power density Note 1: General population/uncontrolled exposures apply in situations in which the general public may be exposed, or in which persons that are exposed as a consequence of their employment may not be fully aware of the potential for exposure or can not exercise control over their exposure. FCC Part 1.1310 Maximum Permissible Exposure (MPE) Computation Procedures 1. The power density of the EUT antenna, P was computed based on the following formula: d = √[(30PG)/377S] where P = Power in W S = Power density, W/m 2 d = Test distance, m G = Numerical isotropic gain 2. The distance, d was computed. The distance d is the minimum distance between the EUT antenna and user that must be maintained to ensure compliance of this requirement. FCC Part 1.1310 Maximum Permissible Exposure (MPE) Computation Method P = 0.0447W S = 10 W/m 2 (limit) G = 1 ( 0dBi) d = √[30PG/377S] = 18.86mm Therefore: The distance between the EUT antenna and users shall be maintained at least 1.88cm to ensure a safe RF exposure when using the EUT.

COMMUNICATION CERTIFICATION LABORATORY 1940 West Alexander Street Salt Lake City, UT 84119 801-972-6146 Test Report Certification Test Of: Radio Modem CR2AG-R0-01-02 FCC ID: QQ6-BTR02 Test Specification: FCC PART 15, Subpart C Test Report Serial No:874 Applicant: The Code Corporation 11814 South Election Road, Suite 200 Draper, UT 84020 Dates of Test: June 20 & 21, 2007 Issue Date: September 27, 2007 Accredited Testing Laboratory By: NVLAP Lab Code 100272-0 COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 874 FCC ID: QQ6-BTR02 Page 2 of 41 CERTIFICATION OF ENGINEERING REPORT This report has been prepared by Communication Certification Laboratory to document compliance of the device described below with the requirements of Federal Communications Commission (FCC) Part 15, Subpart C. This report may be reproduced in full. Partial reproduction may only be made with the written consent of the laboratory. The results in this report apply only to the sample tested. - Applicant: The Code Corporation - Manufacturer: The Code Corporation - Brand Name: The Code Corporation - Model Number: Radio Modem CR2AG-R0-01-02 - FCC ID Number: QQ6-BTR02 On this 27 th day of September 2007, I, individually, and for Communication Certification Laboratory, certify that the statements made in this engineering report are true, complete, and correct to the best of my knowledge, and are made in good faith. Although NVLAP has accredited the Communication Certification Laboratory EMC testing facilities, this report must not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. COMMUNICATION CERTIFICATION LABORATORY Tested by: Norman P. Hansen EMC Technician COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 874 FCC ID: QQ6-BTR02 Page 3 of 41 TABLE OF CONTENTS PAGE SECTION 1.0 CLIENT INFORMATION.................................4 SECTION 2.0 EQUIPMENT UNDER TEST (EUT) ..........................5 SECTION 3.0 TEST SPECIFICATION, METHODS & PROCEDURES ...........7 SECTION 4.0 OPERATION OF EUT DURING TESTING ...................16 SECTION 5.0 SUMMARY OF TEST RESULTS...........................17 SECTION 6.0 MEASUREMENTS, EXAMINATIONS AND DERIVED RESULTS.....18 APPENDIX 1 TEST PROCEDURES AND TEST EQUIPMENT ..................34 APPENDIX 2 PHOTOGRAPHS.........................................37 COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 874 FCC ID: QQ6-BTR02 Page 4 of 41 SECTION 1.0 CLIENT INFORMATION 1.1 Applicant: Company Name: The Code Corporation 11814 South Election Road, Suite 200 Draper, UT 84020 Contact Name: Ryan Hyde Title: VP of Engineering 1.2 Manufacturer: Company Name: The Code Corporation 11814 South Election Road, Suite 200 Draper, UT 84020 Contact Name: Ryan Hyde Title: VP of Engineering COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 874 FCC ID: QQ6-BTR02 Page 5 of 41 SECTION 2.0 EQUIPMENT UNDER TEST (EUT) 2.1 Identification of EUT: Brand Name: The Code Corporation Model Number: Radio Modem CR2AG-R0-01-02 Serial Number: None Options Fitted: N/A 2.2 Description of EUT: The Radio Modem CR2AG-R0-01-02 is a Bluetooth radio module for use with Code Corporation devices such as the CR2 barcode scanner. The Radio Modem CR2AG-R0-01-02 sends the data from the host device to another Bluetooth device. The Radio Modem CR2AG- R0-01-02 was tested in a stand alone configuration as a module with wiring attached so the radio could be controlled for testing. This report covers the transmitter that is required to meet the requirements of FCC Part 15, Subpart C. 2.3 EUT and Support Equipment: The FCC ID numbers for the EUT and support equipment used during the test are listed below: Brand Name Model Number Serial No. FCC ID Number Description Name of Interface Ports / Interface Cables BN: Code Corporation MN: Radio Modem CR2AG-R0-01-02 (Note 1) QQ6- BTR02 Bluetooth to USB adapter See Section 2.4 Note: (1) EUT The support equipment listed above was not modified in order to achieve compliance with this standard. COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 874 FCC ID: QQ6-BTR02 Page 6 of 41 2.4 Interface Ports on EUT: Name of Port No. of Ports Fitted to EUT Cable Descriptions/Length Interface 1 Direct connection to main PCB of barcode scanner (Note 1) Note 1: For testing a cable was connected to provide 3.3 VDC and control the Bluetooth transmitter. 2.5 Modification Incorporated/Special Accessories on EUT: The following modifications were made to the Radio Modem CR2AG-R0-01-02 by the Client during testing to comply with the specification. These modifications will be implemented during manufacturing. 1. The power setting for the power amp was set in software to 175. Signature: Typed Name: Ryan Hyde Title: VP of Engineering COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 874 FCC ID: QQ6-BTR02 Page 7 of 41 SECTION 3.0 TEST SPECIFICATION, METHODS & PROCEDURES 3.1 Test Specification: Title: FCC PART 15, Subpart C (47 CFR 15) Purpose of Test: The tests were performed to demonstrate initial compliance for modular certification. 3.2 Requirements: 3.2.1 §15.203 Antenna Requirement An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this Section. The manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. This requirement does not apply to carrier current devices or to devices operated under the provisions of Sections 15.211, 15.213, 15.217, 15.219, or 15.221. Further, this requirement does not apply to intentional radiators that must be professionally installed, such as perimeter protection systems and some field disturbance sensors, or to other intentional radiators which…

Text truncated - open the document above for the full version.

Front View of the Radiated Spurious Emission Setup Back View of the Radiated Spurious Emission Setup