QQGBU2096Bluetooth Adaptor

Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful rence to radio or television reception, which can be determined by turning the equipment off and on, the is encouraged to try to correct the interference by one of the following measures: interfe Reorient or relocate the receiving antenna. user . Increase the separation between the equipment and receiver. . Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. . . Consult the dealer or an experienced radio/TV technician for help. FCC Caution :To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices). FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. User Manual 1. Package Content Before installation, please check if the following package content is missing. If anything missing, please contact your local distributor. z Bluetooth Mini USB Adapter z Software CD including User manual, Driver and utility 2. Installation steps NOTE：Please install the USB Bluetooth Software Driver before plugging the USB adapter ! 2-1.Place the installation CD-ROM into the PC, the setup should start automatically. If the setup does not start, please go to Windows Explorer, locate the CD-ROM and run [setup.exe]. 2-2. On the Welcome screen click [Next] to continue. 2-3. Read the License Agreement and select [I accept the terms in the license agreement]. Click [Next] . 2-4. Click [Next] to accept the default destination folder, click [Change] to browse to a new destination folder for the Bluetooth software. 2-5.Click [Install] to begin the installation of the Bluetooth software. 2-6. For Windows 2000/XP users, a [Driver Signature Notice] window appears, please click the [OK] button. 2-7.The [Bluetooth device not found] window appears. Plug the USB Bluetooth adapter into the USB port. Click [OK]. 2-8. Click [Finish] to complete the Bluetooth software installation. 2-9. Click [Yes] to restart the computer and complete the installation. 2-10. After reboot your pc, the CD-ROM driver will be completely installed and the [Bluetooth icon] resides in the Windows system tray. 2-11. Click [start/(settings)/controlpanel/system/devicemanager]. Check under“ Bluetooth Devices” then a “ Bluetooth Device” is installed. 2-12. If the information is not presented, please unplug the Mini USB adapter, re-plug the CD-ROM to initiate the driver.

J-THREE INTERNATIONAL HOLDING CO., LTD. No. 23-7, Dungshyh 12 Lirn, Dungshyh Lii Pingchien City, Taoyuan Hsien 324, Taiwan 03/04/2008 Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 To whom it may concern: We, the undersigned, hereby authorize Taiwan ETS Product Service Co., Ltd. to act on our behalf in all matters relating to applications for equipment authorization Bluetooth Adaptor (Model No.: BU-2096, FCC ID: QQGBU2096) including the signing of all documents relating to these matters. Any and all acts carried out by Taiwan ETS Product Service Co., Ltd. on our behalf shall have the same effect as acts of our own. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely, Signature Name: David Wu Title: Product Manager Company: J-THREE INTERNATIONAL HOLDING CO., LTD.

Registration number: W6M20802-8867-P-15 FCC ID: QQGBU2096 Taiwan ETS Product Service Co., Ltd. Appendix page 60 of 65 External photos Registration number: W6M20802-8867-P-15 FCC ID: QQGBU2096 Taiwan ETS Product Service Co., Ltd. Appendix page 61 of 65

BU-2096 QQGBU2096 China

Registration number: W6M20802-8867-P-15 FCC ID: QQGBU2096 Taiwan ETS Product Service Co., Ltd. Appendix page 62 of 65 Internal photos Registration number: W6M20802-8867-P-15 FCC ID: QQGBU2096 Taiwan ETS Product Service Co., Ltd. Appendix page 63 of 65

MPE Prediction FCC Rule: 15.247(b)(5) Systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess of the Commission’s guidelines. See §1.1307(b)(1) of this Chapter. LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm2) Average time (minutes) (A)Limits For Occupational / Control Exposures 30-300 61.4 0.613 1.0 6 300-1500 ... ... F/300 6 1500-100,000 ... ... 5 6 (B)Limits For General Population / Uncontrolled Exposure 30-300 27.5 0.073 0.2 30 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz Prediction of MPE limit at a given distance Equation from page 18 of OET Bulletin 65, Edition 97-01 PG S = -------------- 4πR² where: S = power density P = power input to the antenna G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna Maximum peak output power at antenna input terminal: 11.07 (dBm) Maximum peak output power at antenna input terminal: 12.7938 (mW) Antenna gain(maximal): -2.84 (dBi) Prediction distance: 20 (cm) Prediction frequency: 2441 (MHz) MPE limit for uncontrolled exposure at prediction frequency: 1.0 (mW/cm²) Power density at prediction frequency: 0.0015271 (mW/cm²) The manual instruct the user to install and operate the device in a minimum distance of 20 cm between antenna and the users body.

of Applicant: J-THREE INTERNATIONAL HOLDING CO., LTD. Address: No. 23-7, Dungshyh 12 Lirn, Dungshyh Lii Pingchien City Taoyuan Hsien, 324 Taiwan Tested and Prepared by Taiwan ETS Product Service Co., Ltd. FCC Registration No.: 930600 Industry Canada filed test laboratory Reg. No. IC 5679A-1 A2LA Accredited No.: 1983.02 PTCRB Accredited Type Certification Test House Report No.: W6M20802-8867-P-15 6F, NO. 58, LANE 188, RUEY-KUANG RD., NEIHU TAIPEI 114, TAIWAN, R.O.C. TEL: 886-2-66068877 FAX: 886-2-66068879 E-mail: [email protected] FCC PART 15 SUBPART C TEST REPORT for Bluetooth Adaptor Model No.: BU-2096 FCC ID: QQGBU2096 Registration number: W6M20802-8867-P-15 FCC ID: QQGBU2096 Taiwan ETS Product Service Co., Ltd. Page 1 of 30 TABLE OF CONTENTS 1 GENERAL INFORMATION ...................................................................................................... 2 1.1 Notes .................................................................................................. 2 1.2 Testing laboratory .................................................................................................. 3 1.2.1 Location .................................................................................................. 3 1.2.2 Details of accreditation status .............................................................................................. 3 1.3 Details of approval holder .................................................................................................. 3 1.4 Application details .................................................................................................. 4 1.5 General information of Test item......................................................................................... 4 1.6 Test standards .................................................................................................. 5 2 TECHNICAL TEST .................................................................................................................... 6 2.1 Summary of test results .................................................................................................. 6 2.2 Test environment .................................................................................................. 6 2.3 Test Equipment List .................................................................................................. 7 2.4 General Test Procedure .................................................................................................. 9 3 TEST RESULTS (ENCLOSURE) ............................................................................................ 11 3.1 Peak Output Power (transmitter) ....................................................................................... 12 3.2 RF Exposure Compliance Requirements ........................................................................... 14 3.3 Out of Band Radiated Emissions ....................................................................................... 14 3.4 Transmitter Radiated Emissions in restricted Bands ......................................................... 15 3.5 Spurious emissions (tx) ................................................................................................ 16 3.6 Carrier Frequency Separation ............................................................................................ 20 3.7 Number of Hopping Frequencies....................................................................................... 21 3.7.1 Pseudorandom Frequency Hopping Sequence................................................................... 21 3.7.2 Coordination of hopping sequences to other transmitters ................................................. 21 3.7.3 System Receiver Hopping Capability ................................................................................ 21 3.8 Time of Occupancy (Dwell Time) ..................................................................................... 22 3.9 20dB Bandwidth ................................................................................................ 24 3.9.1 System Receiver Input Bandwidth .................................................................................... 24 3.10 Band-edge Compliance of RF Emissions .......................................................................... 25 3.11 Radiated Emissions from Receiver Section of Transceiver............................................... 27 3.12 Power Line Conducted Emission....................................................................................... 27 Appendix..........................................................................................................30 Registration number: W6M20802-8867-P-15 FCC ID: QQGBU2096 Taiwan ETS Product Service Co., Ltd. Page 2 of 30 1 General Information 1.1 Notes The purpose of conformity testing is to increase the probability of adherence to the essential requirements or conformity specifications, as appropriate. The complexity of the technical specifications, however, means that full and thorough testing is impractical for both technical and economic reasons. Furthermore, there is no guarantee that a test sample which has passed all the relevant tests conforms to a specification. Neither is there any guarantee that such a test sample will interwork with other genuinely open systems. The existence of the tests nevertheless provides the confidence that the test sample possesses the qualities as maintained and that is performance generally conforms to representative cases of communications equipment. The test results of this test report relate exclusively to the item tested as specified in 1.5. The test report may only be reproduced or published in full. Reproduction or publication of extracts from the report requires the prior written approval of the Taiwan ETS Product Service Co., Ltd. Tester: February 27, 2008 Jay Chaing Date ETS-Lab. Name Signature Technical responsibility for area of testing: …

Text truncated - open the document above for the full version.

Registration number: W6M20802-8867-P-15 FCC ID: QQGBU2096 Taiwan ETS Product Service Co., Ltd. Appendix page 64 of 65 Set Up Photo of Radiated Emission RF Mode Registration number: W6M20802-8867-P-15 FCC ID: QQGBU2096 Taiwan ETS Product Service Co., Ltd. Appendix page 65 of 65 Set Up Photo of Conducted Emission