QRKH1469320MP9320 2.8 UHF 4-PORT RFID READER

THEPOWERTOCHOOSE TM User’s Guide MP9320 v2.8 EPC UHF Reader SAMSys MP9320 v2.8 UHF Reader User’s Guide First Edition (April 21, 2005) © Copyright 2005 SAMSys Technologies, Inc. All Rights Reserved. Disclaimer and Limitation of Liability The content of this manual is for information use only and is subject to change without notice. SAMSys assumes no responsibility or liability for any errors or inaccuracies that may appear in this publication. No part of this manual may be reproduced in any form or by any means, electronic, mechanical, recording, or otherwise, without the prior written permission of SAMSys. SAMSys products are not designed, intended, authorized or warranted to be suitable for life support applications or any other life critical applications which could involve potential risk of death, personal injury, property damage, or environmental damage. About SAMSys SAMSys Technologies, Inc. is a world-leading provider of RFID reader hardware solutions in the LF, HF, and UHF segments of the RFID marketplace. SAMSys is a public company listed on the Toroto Stock Exchange under the symbol SMY. SAMSys Technologies, Inc. 44 East Beaver Creek Rd., Unit 11 Richmond Hill, Ontario L4B 1G8 Canada Phone: (905) 707-0404 Toll Free: (877) 367-4342 Fax: (905) 707-9944 E-mail: [email protected] Web: www.samsys.com Manual Part Number: HI469320-28-UG-P1.0 Federal Communications Commission (FCC) Notice (Preliminary) This device was tested and found to comply with the limits set forth in Part 15 of the FCC Rules. Operation is subject to the following conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This device generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instruction manual, the product may cause harmful interference to radio communications. Operation of this product in a residential area is likely to cause harmful interference, in which case, the user is required to correct the interference at their own expense. The authority to operate this product is conditioned by the requirements that no modifications be made to the equipment unless the changes or modifications are expressly approved by SAMSys Technologies. Trademarks SAMSys is a trademark of SAMSys Technologies, Inc. HyperTerminal ® is a registered trademark of Hilgraeve, Inc. EPC is a trademark of EPCglobal, Inc. Other company, product or service names appearing in this manual may be trademarks or service marks of their respective owners. MP9320 V2.8 User’s Guide i Contents Chapter 1 – Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Unpacking the Reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 About the MP9320 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Physical Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Chapter 2 – Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Antenna Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Reader Mechanical Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 RS-485/Ethernet Communication Selection . . . . . . . . . . . . . . . . . . . . . . . 13 Serial (RS-232) Communication Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Ethernet LAN Communication Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Installing the RF Command Suite Application . . . . . . . . . . . . . . . . . . . . . 15 Configuring the IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Digital (TTL) Input/Output Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Transmit Power Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Chapter 3 – Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 MP9320 Power Up and Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Starting RF Command Suite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Setting the RF Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Selecting the Number of Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Selecting Tag Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Enabling or Disabling Tag Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Reading Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Writing Blank Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Modifying Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Chapter 4 – Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 General Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Contact Us . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Chapter – Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Reader Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Battery Specifications (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Power Supply …

Text truncated - open the document above for the full version.

THEPOWERTOCHOOSE TM User’s Guide MP9320 v2.8 EPC UHF Reader SAMSys MP9320 v2.8 UHF Reader User’s Guide First Edition (May 26, 2005) © Copyright 2005 SAMSys Technologies, Inc. All Rights Reserved. Disclaimer and Limitation of Liability The content of this manual is for information use only and is subject to change without notice. SAMSys assumes no responsibility or liability for any errors or inaccuracies that may appear in this publication. No part of this manual may be reproduced in any form or by any means, electronic, mechanical, recording, or otherwise, without the prior written permission of SAMSys. SAMSys products are not designed, intended, authorized or warranted to be suitable for life support applications or any other life critical applications which could involve potential risk of death, personal injury, property damage, or environmental damage. About SAMSys SAMSys Technologies, Inc. is a world-leading provider of RFID reader hardware solutions in the LF, HF, and UHF segments of the RFID marketplace. SAMSys is a public company listed on the Toroto Stock Exchange under the symbol SMY. SAMSys Technologies, Inc. 44 East Beaver Creek Rd., Unit 11 Richmond Hill, Ontario L4B 1G8 Canada Phone: (905) 707-0404 Toll Free: (877) 367-4342 Fax: (905) 707-9944 E-mail: [email protected] Web: www.samsys.com Manual Part Number: HI469320-28-UG-P1.2 Federal Communications Commission (FCC) Notice (Preliminary) This device was tested and found to comply with the limits set forth in Part 15 of the FCC Rules. Operation is subject to the following conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This device generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instruction manual, the product may cause harmful interference to radio communications. Operation of this product in a residential area is likely to cause harmful interference, in which case, the user is required to correct the interference at their own expense. The authority to operate this product is conditioned by the requirements that no modifications be made to the equipment unless the changes or modifications are expressly approved by SAMSys Technologies. Trademarks SAMSys is a trademark of SAMSys Technologies, Inc. HyperTerminal ® is a registered trademark of Hilgraeve, Inc. EPC is a trademark of EPCglobal, Inc. Other company, product or service names appearing in this manual may be trademarks or service marks of their respective owners. MP9320 V2.8 User’s Guide i Contents Chapter 1 – Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Unpacking the Reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 About the MP9320 V2.8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Physical Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Chapter 2 – Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Antenna Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Reader Mechanical Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 RS-485/Ethernet Communication Selection . . . . . . . . . . . . . . . . . . . . . . . 13 Serial (RS-232) Communication Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Ethernet LAN Communication Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Installing the RF Command Suite Application . . . . . . . . . . . . . . . . . . . . . 15 Configuring the IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Digital Input/Output Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Transmit Power Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Chapter 3 – Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 MP9320 V2.8 Power Up and Initialization . . . . . . . . . . . . . . . . . . . . . . . . 20 Starting RF Command Suite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Setting the RF Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Selecting the Number of Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Selecting Tag Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Enabling or Disabling Tag Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Reading Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Writing Blank Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Modifying Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Chapter 4 – Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 General Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Contact Us . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Chapter 5 – Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Reader Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Battery Specifications (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Power Supply Spec…

Text truncated - open the document above for the full version.

Field Installation and Calibration Guide MP9320 UHF Reader 2 Fourth Edition (May 1, 2005) V4.1 © Copyright 2005 SAMSys Technologies, Inc. All Rights Reserved. Disclaimer and Limitation of Liability The content of this manual is for information use only and is subject to change without notice. SAMSys assumes no responsibility or liability for any errors or inaccuracies that may appear in this publication. No part of this manual may be reproduced in any form or by any means, electronic, mechanical, recording, or otherwise, without the prior written permission of SAMSys. SAMSys products are not designed, intended, authorized or warranted to be suitable for life support applications or any other life critical applications which could involve potential risk of death, personal injury, property damage, or environmental damage. About SAMSys SAMSys is the world leader in the design and supply of radio frequency identification (RFID) hardware solutions for high volume pallet and reusable container tracking applications in global logistics management, materials handling, and supply chain industries. SAMSys is a public company listed on the Canadian Venture Exchange under the symbol SMY. SAMSys Technologies, Inc. 44 East Beaver Creek Rd., Unit 11 Richmond Hill, Ontario L4B 1G8 Canada Phone: (905) 707-0404 Toll Free: (877) 463-6546 Fax: (905) 707-9944 E-mail: [email protected] Web: www.samsys.com Federal Communications Commission (FCC) Notice This device was tested and found to comply with the limits set forth in Part 15 of the FCC Rules. Operation is subject to the following conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This device generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instruction manual, the product may cause harmful interference to radio communications. Operation of this product in a residential area is likely to cause harmful interference, in which case, the user is required to correct the interference at their own expense. The authority to operate this product is conditioned by the requirements that no modifications be made to the equipment unless the changes or modifications are expressly approved by SAMSys Technologies. 3 Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Assumptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Getting Technical Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Antenna Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Antenna Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Antenna Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Reader Mechanical Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Hollow Concrete Block Wall Mounting. . . . . . . . . . . . . . . . . . . . . . . . . 9 Solid Concrete Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Wood or Metal Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Drywall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 RS-485/Ethernet Communication Selection . . . . . . . . . . . . . . . . . . . . . . . . 11 RS-485 Impedance Matching Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Serial (RS-232) Communication Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Ethernet LAN Communication Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Installing the RF Command Suite Application . . . . . . . . . . . . . . . . . . . . . . 13 Configuring the IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Digital (TTL) Input/Output Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Setting Digital Input for Reader Duty Cycle Control . . . . . . . . . . . . . . . . . 15 Transmit Power Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Transmitter and Antenna Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Multiplexer Configuration Word (MCW) . . . . . . . . . . . . . . . . . . . . . . . 17 Multiplexer Select Word (MSW) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Transmit Power Configuration (TPC) . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Antenna Transmit Power (TPx) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Manual Field Power Calibration - FCC Readers . . . . . . . . . . . . . . . . . . . . . 22 Manual Field Power Calibration - ETSI Readers . . . . . . . . . . . . . . . . . . . . 24 4 Introduction This document is intended to assist technical service personnel engaged in the installation of the SAMSys MP9320 UHF Reader. The document includes procedures for installing and configuring the reader to meet local standards and regulatory requirements. Topics and procedures presented in this document include the following: •Antenna Installation •Reader Mechanical Installation •RS-485/Ethernet Communication Selection •RS-485 Impedance Matching Selection •Serial (RS-232) Communication Setup •Ethernet LAN Communication Setup •Installing the RF Command Suite Application •Configuring the IP Address •Digital (TTL) Input/Output Setup •Setting Digital Input for Reader Duty Cycle Control •Transmit Power Calibration •Transmitter and Antenna Configuration •Manual Field Power Calibration - FCC Readers •Manual Field Power Calibration - ETSI Readers Assumptions This do…

Text truncated - open the document above for the full version.

. . . . . . . . www.samsys.com 2525 Meridian Parkway, Ste. 60 Durham, North Carolina 27713 USA Phone: (919) 281-1541 Toll Free: (877) 367-4342 Fax: (919) 281-1551 44 E. Beaver Creek Rd., Unit 11 Richmond Hill, Ontario L4B 1G8 Canada Phone: (905) 707-0404 Toll Free: (888) 483-6646 Fax: (905) 707-9944 SAMSys Technologies, Inc. Samsys Technologies, Inc. 2525 Meridian Parkway Suite 60 Durham, North Carolina 27713 USA 26 June 2005 RE: Confidentiality Request Dear Reviewer: This letter is a request for confidentiality for specific exhibits in reference to the MP9320 2.8 UHF 4- Port RFID Reader under FCC ID: QRKH1469320. The following exhibits are requested to be held in confidentiality and withheld from public inspection pursuant to 47 CFR 0.457(d): Schematics Block Diagrams These exhibits contain details of the proprietary operation of the product. These details are not readily discernible from the hardware, constitute trade secrets, and are not generally accessible by the public. We request that the above documents and this letter be withheld from public inspection. Please contact us if further justification for any of the above exhibits is necessary. Sincerely, James Stiscia Director of Hardware Engineering

External Photos

Label Sample/Placement for: QRKH1469320

Internal Photos

MP9320 Operational Overview The MP9320 UHF Long-Range Reader is a member of the SAMSys family of Radio Frequency Identification (RFID) products. RFID is a wireless data acquisition method used to remotely retrieve product data such as part number, date-of-manufacture, quantity, version, and other information. All RFID systems are comprised of the following components: • Transponders (tags) attached to a product • Reader/Interrogator to write and read tag data • Reader/Interrogator Antenna Transponders (Tags) The transponder or tag is the data-carrying device attached to the product or container and can come in any shape or size. The most common are the “credit card” tags used for security access and the larger plastic, anti-theft tags used by retailers. Whatever the size or application, each tag always consists of a coupler (antenna coil) and a microcircuit. Tags operate in read/write mode. In other words, data can be rewritten to the tag as well as read from the tag. The tag communicates with the reader across the air-interface. This interface is defined by its carrier frequency, bit data rate, encoding method and other parameters. Tags are typically referred to as either active or passive devices depending on the power source. Active tags contain an internal battery and have longer read ranges but a limited operation life. Low frequency passive tags do not have an internal battery and are powered by inductive or capacitance coupling when the tag is in the RF field of the reader. These tags typically have shorter read ranges, but have substantially longer operational lives. UHF tags, like those used with the MP9320, use reflected electromagnetic backscatter coupling. These tags operate in the 902-928 MHz range and typically have longer read ranges. When a UHF tag passes through the RF field, the tag is energized by the reader’s time- varying, electromagnetic RF wave. This signal is called the carrier signal. When the RF field passes through the antenna, an AC voltage is generated. This voltage is rectified to supply power to the tag’s microcircuit. As the microcircuit load and unloads the tag’s antenna terminals, the information in the tag is transmitted back to the reader. This modulation scheme is referred to as On-Off-Keying (OOK). MP9320 Reader The reader contains a transmitter section, receiver section, and controller section. The transmitter section contains an RF generator, amplifiers, and the coupling circuit. The receiver section contains the envelope detector, amplifiers, demodulator, and analog/digital converter. The controller section includes the microprocessor and any input/output communication interfaces. The reader transmits a 902-928 MHz signal to the external antenna. This RF field can range from 6 inches to 30 feet depending on the power and frequency. The RF field generated by the reader performs the following: • Energize the tag antenna to provide power to the integrated circuit • Provide a synchronized clock source for the tag • Act as a carrier for returned tag data The reader is constantly generating the RF carrier. During this time the reader is monitoring the return signal for modulation indicating the presence of a tag. When a tag enters the RF field, the antenna is energized and the tag starts to divide down the carrier, demodulate commands from the reader, and begins to clock data to the output transistor. The output transistor shunts the antenna coil causing momentary fluctuations in the carrier amplitude. The reader detects this amplitude-modulated data and decodes the resulting bit stream into the actual tag data. The decoding scheme depends on the specific tag protocol.

TEST REPORT FROM d For MP9320 2.8 UHF 4-Port RFID Reader To FCC Part 15.247, 15.207, 15.209, IC RSS-210 Test Report Serial No.: SL05042907T-SCI-006 This report supersedes none Remarks: Equipment complied with the specification [X ] Equipment did not comply with the specification [ ] This Test Report is Issued Under the Authority of: .......................................................................................................... Tested by: Alvin Ilarina, Test Enginner .......................................................................................................... Reviewed by: Leslie Bai, Lab Manager Issue date: 24 June 2005 Equipment Details: Manufacturer: SAMSys This test report may be reproduced in full only. Registration No. 783147 Registration No. 2195 Registration No. 4842 Title: SAMSys MP9320 2.8 UHF 4-Port RFID Reader To: FCC Part 15.247, 15.207, 15.209, IC RSS-210 Serial#SL05042907T-SCI-006 Issue Date 24 June 2005 Page 2 of 30 This page has been left blank intentionally. Title: SAMSys MP9320 2.8 UHF 4-Port RFID Reader To: FCC Part 15.247, 15.207, 15.209, IC RSS-210 Serial#SL05042907T-SCI-006 Issue Date 24 June 2005 Page 3 of 30 CONTENTS EXECUTIVE SUMMARY..............................................................................................................................................5 1 TECHNICAL DETAILS..........................................................................................................................................6 2 TESTS REQUIRED..................................................................................................................................................7 3 MEASUREMENTS, EXAMINATIONS AND DERIVED RESULTS.................................................................8 4 TEST INSTRUMENTATION................................................................................................................................23 APPENDIX A: EUT TEST CONDITIONS.................................................................................................................24 APPENDIX B: EXTERNAL PHOTOS........................................................................................................................25 APPENDIX C: CIRCUIT/BLOCK DIAGRAMS.......................................................................................................26 APPENDIX D: INTERNAL PHOTOS.........................................................................................................................27 APPENDIX F: PRODUCT DESCRIPTION...............................................................................................................28 APPENDIX H: FCC LABEL LOCATION..................................................................................................................29 APPENDIX I: USER MANUAL...................................................................................................................................30 Title: SAMSys MP9320 2.8 UHF 4-Port RFID Reader To: FCC Part 15.247, 15.207, 15.209, IC RSS-210 Serial#SL05042907T-SCI-006 Issue Date 24 June 2005 Page 4 of 30 This page has been left blank intentionally. Title: SAMSys MP9320 2.8 UHF 4-Port RFID Reader To: FCC Part 15.247, 15.207, 15.209, IC RSS-210 Serial#SL05042907T-SCI-006 Issue Date 24 June 2005 Page 5 of 30 Executive Summary The purpose of this test programme was to demonstrate compliance of the SAMSys, MP9320 2.8 UHF 4-Port RFID Reader against the current FCC Part 15.247, 15.207, 15.209, IC RSS-210. The MP9320 2.8 UHF 4-Port RFID Reader demonstrated compliance with the FCC Part 15.247, 15.207, 15.209, IC RSS-210. SAMSys is the applicant and claimed manufacturer of this tested product. For the detailed description of this product, please refer to the MP9320 2.8 UHF 4-Port RFID Reader User Manual. The test has demonstrated that this unit complies with stipulated standards. Professional installation is required for this equipment. Title: SAMSys MP9320 2.8 UHF 4-Port RFID Reader To: FCC Part 15.247, 15.207, 15.209, IC RSS-210 Serial#SL05042907T-SCI-006 Issue Date 24 June 2005 Page 6 of 30 1 Technical Details Purpose Compliance testing of MP9320 2.8 UHF 4-Port RFID Reader with FCC Part 15.247, 15.207, 15.209, IC RSS-210 Applicant / Client SAMSys 2525 Meridian Parkway, Ste. 60 Durham, North Carolina 27713 Manufacturer SAMSys Laboratory performing the tests SIEMIC Labs 2206 Ringwood Avenue San Jose, CA 95131 Test location(s) SIEMIC Labs 2206 Ringwood Avenue San Jose, CA 95131 Test report reference number SL05042907T-SCI-006 Date EUT received 4 May 2005 Standard applied FCC Part 15.247, 15.207, 15.209, IC RSS-210 No of Units: 1 Equipment Category: DSS Trade/Product Name: MP9320 2.8 UHF 4-Port RFID Reader Type/Model Name/No: MP9320 2.8 UHF 4-Port RFID Reader Technical Variants: None FCC ID No. QRKH1469320 Title: SAMSys MP9320 2.8 UHF 4-Port RFID Reader To: FCC Part 15.247, 15.207, 15.209, IC RSS-210 Serial#SL05042907T-SCI-006 Issue Date 24 June 2005 Page 7 of 30 2 Tests Required The product was tested in accordance with the following specifications. The test results recorded in this Test Report are exclusively referred to the tested sample(s). Test Standard Description Pass / Fail 47CFR Part 15, General Conditions 15.207 Power Line Conducted Emissions Pass 15.209, 15.205 Radiated Spurious Emissions Pass 47CFR Part 15, §15.247 15.247(a)1 Carrier Frequency Separation Pass 15.247(a)1 20 dB Bandwidth Pass 15.247(a)1 Number of Hopping Frequencies Pass 15.247(a)1 Time of Occupancy Pass 15.247(b)(1) Power Output Pass 15.247(c) Conducted Spurious Emissions Pass 15.247(c) Radiated Spurious Emissions Pass ANSI C63.4: 2001 Notes: Deviations to above standards are outlined in specific test sections if applicable. Cable loss and external attenuation are compensated for in the measurement system when applicable. Title: SAMSys MP9320 2.8 UHF 4-Port RFID Reader To: FCC Part 15.247, 15.207, 15.209, IC RSS-210 Serial#SL05042907T-SCI-006 Issue Da…

Text truncated - open the document above for the full version.

Test Setup Photos