QS6-GWD910TWireless Microphone

GWD910 Waterproof Wireless Microphone System GWD-910T & GWD-910R Owner’s Manual Taiwan Gomet Technology Co., Ltd. No. 8-1, Lane 212, Sec. 1, Chang-Shang N. Rd, Tamsui, Taipei Shien 25157, Taiwan Tel: +886-2-2621-8029 Fax: +886-2-2623-7605 E-mail [email protected] Website www.gomet.com.tw GWD 900 Wireless Microphone Owner’s Manual 2 Wireless Microphone General Specification THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE CONDITION THAT THIS DEVICE DOES NOT CAUSE HARMFUL INTERFERENCE. ( FCC ID :QS6-GWD910T & QS6-GWD910R ) Modulation Mode: Bi-Directional D SS (Digital Spread Spectrum) Frequency: 902 ~ 92 5 MHz Handset RF Power Output 21.69 dBm / GWD-910T Base Station RF Power Output 20.14 dBm / GWD-910R Operating Range: 1000 ft.(300M) Battery: 3.7V Rechargeable Li-Ion battery (Handset) 5V DC (Base Station) Air Time: 9~10 hours of continuous operation Standby Time: 4 days Microphone: Internal microphone without lavalier Channels: 8 Channels with Automatic Synchronization • This GWD910 is protected agai nst water splashes and dust. • GWD910 Wireless Microphone will automatically turns ON and shut OFF when recording is activated or deacti vated through In-Car Video System. • GWD910 Wireless Microphone is also able to trigger IN-CAR VIDEO SYSTEM to activate digital video recording. • Any GWD910 Wireless Microphone will work with any IN-CAR VIDEO SYSTEM that is equipped with GWD910 receiv ers. - Automatic Synchronization • Build-in Programmable Function Button, Panic Button & Mute Button • LED indicators are used for status on mute, ON/OFF, signal, battery and panic functions. • GWD910 will automatically detect radio fr equency noises, channel conflicts and cross talks with as many as 20 units in close pr oximity, and perform auto switch to ensure clear communication and recording. GWD 900 Wireless Microphone Owner’s Manual 3 Hardware Overview Wireless Microphone Wireless Microphone Receiver GWD910T (-2400T) GWD910R (-2400R) Charger, AC Wall Charger Cable & DC In-Car Charger Cable GWD 900 Wireless Microphone Owner’s Manual 4 System Overview Wireless Microphone Receiver Receiver’s Register Contact (CH1) The register contact is used to synchroni ze the frequency of the receiver and the wireless microphone. Green LED Green LED OFF for Microphone on Standby Mode Green LED ON for Microphone on Recording Mode Red LED Red LED OFF for Panic Mode OFF Red LED ON for Panic Mode ON Red LED Blinking for Wireless Microphone Low Battery Yellow LED Yellow LED OFF for Strong Signal Yellow LED ON for Signal is Marginal or Weak 1 M PS 1 S P M GWD 900 Wireless Microphone Owner’s Manual 5 System Overview Wireless Microphone Receiver SCMIC-PKC/GWD910R Installation No installation is required from the user. The GWD910 wireless microphone receiver is located in the touch screen monitor module of the IN-CAR VIDEO SYSTEM. Power Connection The wireless microphone receiver has no ON / OFF switch. The receiver will become energized in standby mode whenever the IN-CAR VIDEO SYSTEM system is ON. Receiver’s Antennas To prevent damage, antenna for the receiver is package separately. Remove the antenna from the package and tighten the titanium antenna to the receiver. Do not try to lengthen, shorten, or temper with the antennas, which might result in damage of the audio system and may violate FCC regulation. Receiver’s Register Contact The register contact is used to synchronize the frequency of the receiver and the wireless microphone. GWD 900 Wireless Microphone Owner’s Manual 6 System Overview Wireless Microphone /GWD910T LED Indicators (Within the REC & Button 1 & 2) REC Button Green / Blue LED OFF for Standby Mode Green / Blue LED ON for Recording Mode Green / Blue LED Fast Blink for Mute Recording Red LED Slow Blink for Low Battery Red LED ON for Panic Mode ON Red LED OFF for Panic Mode OFF Programmable Button 1 Blue LED ON for Programmable 1 Function ON Yellow LED OFF for Strong Signal Yellow LED ON for Signal is Marginal or Weak Programmable Button 2 Green LED ON for Programmable 2 Function ON REC Button: Audio / Video Recording ON (Press REC Button once) This action will initiate the IN-CAR VIDEO SYSTEM to record both audio and video data. To stop recording, press the stop button on the IN-CAR VIDEO SYSTEM monitor module. Panic ON (Press and hold REC Button for 3 second) Wireless microphone will automatically send a panic signal to the IN-CAR VIDEO SYSTEM ; the signal will be relayed back to the station for process. (This function is only available if the wireless communication is established) The Panic Mode may be deactivated by holding down the REC button for another 3 seconds. Buzzer Produce Warning Tone PB 1: Programmable Button 1 PB 2: Programmable Button 2 Microphone Audio Input. Antenna External Antenna base for long distance used. REC+PB1 Hold both Button 3 Seconds for Covert Mode: Switching Warning Features between Vibration and (LED + Buzzer + Vibration ) 12 6 4 3 4 2 5 1 6 3 5 GWD 900 Wireless Microphone Owner’s Manual 7 System Overview Wireless Microphone SCMIC-TRAN2/GWD910T Battery Selection and Installation The GWD910 wireless microphone is powered by a rechargeable lithium-ion battery. The wireless microphone housing is designed to prevent incorrect installation of the battery. Do not force the battery in to the housing. Reversed batteries may cause damage to the wireless microphone. The battery compartment is located at the bottom of the wireless microphone. Slide off the battery cover and remove the silicon seal, at this point the battery is free to slide out. Transmitting Antenna The GWD910 Wireless Microphone includes a flexible antenna, which is package separately to prevent damage. Remove the antenna from the package and tighten the antenna to the wireless microphone. For best result, allow the antenna to extent fully. If the signal is marginal, please experiment with different wireless microphone position on your body. Do not attempt to remove, replace or change the…

Text truncated - open the document above for the full version.

[email protected] <[email protected]>Wed, Aug 25, 2010 at 10:19 PM To: [email protected] Cc: [email protected], [email protected], [email protected] Dear Tim Please see my reply. Thank you very much. Best regards, 蕭若茵 / Jill Shiau 程智科技股份有限公司 Compliance Certification Services Inc. Tel: 886-3-324-0332#27 Fax: 886-3-324-7460 E-Mail: [email protected] 寄件人:<[email protected]> 收件人:<[email protected] >, <[email protected]> 副本抄送:<[email protected] >, <[email protected]> 日期:2010/08/26 上午 09:56 主旨:Taiwan Gomet Technology Co., Ltd., FCC ID: QS6-GW D910T, Assessment NO.: AN10T0788, Notice#1 Dear Jill, Review of this application is complete. Please send replies to the following issues. Q1: Test report page 8 indicates that the Boonton 52012 USB Power Sensor is beyond the calibration period. It appears that this power sensor was not used for this test. Please confirm. 8/26 Jill We don't use Power sensor for test. Removed the Power Sensor from test report. Please see attached file. Q2: Please confirm that this transmitter is for handheld operation only and that it is not for body-worn operation. The transmitter output power is greater than the FCC low threshold power of 66 mW for operation in this band. Certification of this device for body-worn configuration would require SAR evaluation. 8/26 Jill The EUT is a handhold device. The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information within 30 days of the original e-mail date may result in application dismissal and forfeiture of the filing fee. Also, please note that partial responses increase processing time and should not be submitted. Any questions about the content of this correspondence should be directed to the e-mail address listed below the name of the sender. Revised documentation should not be emailed, but instead should be submitted through "Add Attachment" function at the UL-CCS website. Please have your Assessment Number and FCC ID/IC Certification number handy. You may use the following link: https://cert.ccsemc.com/ filing/ Best regards Tim Dwyer Technical Reviewer ______________________________________________________________ This e-mail transmission is confidential and intended solely for being reviewed by the recipient(s) identified above. If you are not an identified recipient, please ensure that this communication remains confidential and promptly return it to the sender. Please contact immediately by phone (Tel: 886-2-2299-9720) for any problem with this transmission. Thank you for your attention. GWD910T TestReport 0826.pdf 804K

Report No: T100622103 Page 1 / 9 EXTERNAL PHOTOGRAPHS OF EUT Report No: T10062103 Page 2 Report No: T10062103 Page 3 Report No: T10062103 Page 4 Report No: T10062103 Page 5

Label Location & Foramat Label Here FCC ID: QS6-GWD910T Note: conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Report No: T10062103 Page 6 INTERNAL PHOTOGRAPHS OF EUT Report No: T10062103 Page 7 Report No: T10062103 Page 8 Report No: T10062103 Page 9

Compliance Certification Services Inc. Report No.: T100622103-RP1 FCC ID: QS6-GWD910T Date of Issue: Oct. 6, 2010 Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. Page 1 Total Page: 57 Rev. 00 FCC 47 CFR PART 15 SUBPART C TEST REPORT For Wireless Microphone Model: GWD910T Trade Name: GOMET Issued to Taiwan Gomet Technology Co., Ltd. No. 8-1, Lane 212, Sec. 1, Chung-Shan N. Road Tamsui, Taipei, Taiwan 251 Issued by Compliance Certification Services Inc. No. 81-1, Lane 210, Pa-De 2nd Rd., Luchu Hsiang, Taoyuan Shien, (338) Taiwan, R.O.C. TEL: 886-3-324-0332 FAX: 886-3-324-5235 http://www.ccsrf.com [email protected] Compliance Certification Services Inc. Report No.: T100622103-RP1 FCC ID: QS6-GWD910T Date of Issue: Oct. 6, 2010 Page 2 Rev. 00 Revision History Rev. Issue Date Revisions Effect Page Revised By 00 Sep. 10, 2010 Initial Issue ALL Jill Shiau Compliance Certification Services Inc. Report No.: T100622103-RP1 FCC ID: QS6-GWD910T Date of Issue: Oct. 6, 2010 Page 3 Rev. 00 TABLE OF CONTENTS 1. TEST RESULT CERTIFICATION ...........................................................................................4 2. EUT DESCRIPTION................................................................................................................5 3. TEST METHODOLOGY..........................................................................................................6 3.1 EUT CONFIGURATION.....................................................................................................6 3.2 EUT EXERCISE.................................................................................................................6 3.3 GENERAL TEST PROCEDURES .....................................................................................6 3.4 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS .........................................7 3.5 DESCRIPTION OF TEST MODES ....................................................................................7 4. INSTRUMENT CALIBRATION ...............................................................................................8 4.1 MEASURING INSTRUMENT CALIBRATION ....................................................................8 4.2 MEASUREMENT EQUIPMENT USED ..............................................................................8 4.3 MEASUREMENT UNCERTAINTY.....................................................................................9 5. FACILITIES AND ACCREDITATIONS .................................................................................10 5.1 FACILTIES .......................................................................................................................10 5.2 EQUIPMENT....................................................................................................................10 5.3 TABLE OF ACCREDITATIONS AND LISTINGS .............................................................11 6. SETUP OF EQUIPMENT UNDER TEST ..............................................................................12 6.1 SETUP CONFIGURATION OF EUT ................................................................................12 6.2 SUPPORT EQUIPMENT .................................................................................................12 7. FCC PART 15.247 REQUIREMENTS ..................................................................................13 7.1 6 DB BANDWIDTH ............................................................................................................13 7.2 PEAK POWER .................................................................................................................16 7.3 AVERAGE POWER .........................................................................................................19 7.4 BAND EDGES MEASUREMENT.....................................................................................22 7.5 PEAK POWER SPECTRAL DENSITY ............................................................................24 7.6 SPURIOUS EMISSIONS .................................................................................................27 7.7 POWERLINE CONDUCTED EMISSIONS.......................................................................48 8. APPENDIX I RADIO FREQUENCY EXPOSURE .................................................................51 9. APPENDIX II PHOTOGRAPHS OF TEST SETUP...............................................................52 Compliance Certification Services Inc. Report No.: T100622103-RP1 FCC ID: QS6-GWD910T Date of Issue: Oct. 6, 2010 Page 4 Rev. 00 1. TEST RESULT CERTIFICATION Applicant: Taiwan Gomet Technology Co., Ltd. No. 8-1, Lane 212, Sec. 1, Chung-Shan N. Road Tamsui, Taipei, Taiwan 251 Manufacturer: Taiwan Gomet Technology Co., Ltd. No. 8-1, Lane 212, Sec. 1, Chung-Shan N. Road Tamsui, Taipei, Taiwan 251 Equipment Under Test: Wireless Microphone Trade Name: GOMET Model: GWD910T Date of Test: August 11 ~Oct. 6, 2010 APPLICABLE STANDARDS STANDARD TEST RESULT FCC 47 CFR Part 15 Subpart C No non-compliance noted We hereby certify that: The above equipment was tested by Compliance Certification Services Inc. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4: 2003 and the energy emitted by the sample EUT tested as described in this report is in compliance with the requirements of FCC Rules Part 15.207, 15.209, 15.247. The test results of this report relate only to the tested sample EUT identified in this report. Approved by: Reviewed by: Stan Lin Supervisor Alonso Lu Engineer Compliance Certification Services Inc. Report No.: T100622103-RP1 FCC ID: QS6-GWD910T Date of Issue: Oct. 6, 2010 Page 5 Rev. 00 2. EUT …

Text truncated - open the document above for the full version.

Compliance Certification Services Inc. Report No.: T100622103-RP1 FCC ID: QS6-GWD910T Date of Issue: August 20, 2010 Page 47 Rev. 00 9. APPENDIX II PHOTOGRAPHS OF TEST SETUP Radiated Emission Set up Photos Below 1GHz Dipole Antenna Compliance Certification Services Inc. Report No.: T100622103-RP1 FCC ID: QS6-GWD910T Date of Issue: August 20, 2010 Page 48 Rev. 00 Monopole Antenna Compliance Certification Services Inc. Report No.: T100622103-RP1 FCC ID: QS6-GWD910T Date of Issue: August 20, 2010 Page 49 Rev. 00 Above 1GHz Dipole Antenna Compliance Certification Services Inc. Report No.: T100622103-RP1 FCC ID: QS6-GWD910T Date of Issue: August 20, 2010 Page 50 Rev. 00 Monopole Antenna Compliance Certification Services Inc. Report No.: T100622103-RP1 FCC ID: QS6-GWD910T Date of Issue: August 20, 2010 Page 51 Rev. 00 Conducted Emission Setup Photos Compliance Certification Services Inc. Report No.: T100622103-RP1 FCC ID: QS6-GWD910T Date of Issue: August 20, 2010 Page 52 Rev. 00 Powerline Conducted Emissions Setup Photos