QUSTXSNEWRemote control of electric and electronic equipmen

USER MANUAL RADIO CONTROL TXS 2121 SERIES Radio controller with 12 bit code transmission and the possibility of partialisation of the code for communal and personal command management. It may be used together with other transmitters of the same series and may be perfectly integrated with all the receivers and the SEAV central electronic lines. - Mod. TXS 1 new : one channel T1 - Mod. TXS 2 new : two channels T1, T2 - Mod. TXS 3 new : three channels T1, T2 e T3 TECHNICAL CHARACTERISTICS - Powered by an alkaline battery : 12VDC (23A) - Working frequency : 433,92 MHz - Combinations : 1024 (12 bit code) - Maximum consumption. : 25 mA - Working temperature : -20 ÷ 70 °C - Dimensions : 36x61x14mm. TXS 1 new TXS 2 new TXS 3 new DESCRIPTION OF FUNCTIONING The transmitter, according to the model, is complete with either 1, 2 or 3 buttons for the management of either 1, 2 or 3 different uses. PROGRAMMING By pressing the 10 SW1 switches, moving them to the “ON” or “OFF” position, the desired code may be selected. Such a code must correspond to the code which has been memorised on the receiver. (The standard factory configuration: uneven “ON”). FUNCTIONING PROCEDURES a) Standard 12 bit models T1, T2, and T3. The transmitter which is produced by the factory is made up as follows: TXS 1 new: Jumper J1 and J2 are not included TXS 2 new: Jumper J1 (1-2). J2 not included. b) TXS 3 new: Jumper J1 (1-2), J2 (2-3). Channel separation: 1 communal and 1 or 2 private (if TXS 2 or TXS 3). TXS 2 new: Jumper J1 (2-3), J2 not included. TXS 3 new: Jumper J1 (2-3), J2 (1-2). With this format the radio commander has a communal code (T1) (e.g. condominium entrance door) and one or two private uses (T2 and T3). The separation of the code is the of the 4+6 type, and so the first 4 switches of the SW1 are for the codification of the communal code and the remaining 6 are for the codification of the private code. c) Channel separation: 2 communal and 1 private (only for TXS 3). TXS 3 new: Jumper J1 (2-3), J2 (2-3) With this format the radio commander has two communal codes (T1 and T3) (e.g. condominium entrance door) and one private use (T2). The separation of the code is of the 4+6 type, therefore the first 4 switches of the SW1 are for the codification of the communal code and the remaining 6 are for the codification of the private code. WARNING − The alkaline 12VDC (23A) battery must be changed every year in order to guarantee the correct functioning of the transmitter. − In order to substitute the dead battery remove the plastic cover by sliding it off, take the old battery out and insert the new one taking care to ensure that the polarity corresponds to that indicated on the container. − The used battery must be disposed of correctly in the apt recycling bins. DECLARATION OF CONFORMITY SEAV s.r.l. declares that the product Radio commander TXS 2121 Series is conformant to all of the requirements laid out in the EC directive number: 99/5 which are based on the following standards: - ETS 300 683; - ETS 300 220; - EN 60335-1. The sample which has been tested meets the essential requirements which have been specified above, on the basis of the results of the tests, as demonstrated in the following reports: EMC 906/99, RTX 903/99, LVD 505/00. These reports have been verified by the organisation notified. EMCCert Dr. Rasek (Identification Number: 0678). Osimo, 09/10/00 GB

OBJECT: privacy option. The undersigned company, SEAV S.R.L., with head office at Osimo (AN) via San Sabino 34, requests for full privacy option to prevent competitors to copy its product. Osimo, March 4, 2003 SEAV S.R.L. Diego Cerioni (Approval Manager) SEAV s.r.l. Via San Sabino, 34 – 60027 OSIMO (AN) Italy – P.O. Box 14 Tel. 071.7132758 (r.a.) – Fax 071.7131937 http: //www.seav.com - e-mail: [email protected]

SUBJECT: Request of Confidentiality. FCC ID: QUSTXSNEW 731 Confirmation Number: EA145609 The undersigned company, SEAV S.R.L., with head office at Osimo (AN) via San Sabino 34, requests for full privacy option to prevent competitors to copy its product. The documents subjected to confidentiality are: • Oscillator Block Diagram • Electronic schematics • Component List Osimo, March 4, 2003 SEAV S.R.L. Diego Cerioni (Approval Manager)

External Photo

Picture of Fcc ID and its placement on the equipment

Iternal Photo

OPERATIONAL DESCRIPTION When the user push one of the push buttons the microprocessor read the code (10 bit) defined from the dip switch and send this code together with the two bits of the selected channel to the RF transmitting section with O.O.K. modulation and P.W.M. bit codification.

ELECTRONIC CONTROL PANELS Sliding and swinging gates Hereafter are described the typical receiver used in conjunction with the TXSNEW family. As you can see the transmitter is used to open and close swinging gates and sliding doors. These receiver will be subjected to a dedicated certification procedure. LRS2145 Single-phase electronic control panel for sliding and swinging gates with “narrow-band” built-in receiver, 433.9 Mhz, and the possibility to store up to 120 different dip-switch and / or rolling code radio-controls. Additional functions: initial motor pick-up, deceleration, electronic torque limiter, 12V electric lock. LRS2100 Single-phase electronic control panel for sliding and swinging gates with “narrow-band” built-in receiver, 433.9 Mhz, and the possibility to store dip- switch radio-controls. Additional functions: electronic torque limiter, 12V electric lock. LRS2151 Single-phase electronic control panel for sliding and swinging gates with “narrow-band” built-in receiver, 433.9 Mhz, and the possibility to store up to 63 different dip-switch and / or rolling code radio-controls. Additional functions: electronic torque limiter. LRS2102R SET Single-phase electronic control panel for sliding and swinging gates with “narrow-band” built-in receiver, 433.9 Mhz, and the possibility to store up to 120 different dip-switch and / or rolling code radio-controls. Additional functions: initial pick-up, electronic torque limiter, selectable blinking or courtesy light. LRS2102R Single-phase electronic control panel for sliding and swinging gates with built- in receiver, 433.9 Mhz, and the possibility to store up to 120 different dip- switch and / or rolling code radio-controls. Additional functions: initial pick-up, electronic torque limiter, selectable blinking or courtesy light.

CiaoLab Technologies Standard Compliance Services FCC CFR 47 PART 15 Subpart C E.M.I. TEST REPORT Test report No................ : 03SV001EM-R01 Prepared by.................... : C. Carù Signature .................................... Approved by................... : G. Baroni Signature .................................... Date of issue................... : February 7, 2003 Number of pages............ : 14 Test Laboratory Name..............................: CiaoLab Technologies S.p.A. - Standard Compliance Services Address.......................... : Via ai Laboratori Olivetti, 79 - 20010 Pregnana Milanese (MI) - I Applicant for the test Name................................................ : SEAV S.r.l. Equipment under test Model................................................ : TXS 3 NEW Family.................................... : TXS (1 or 2 or 3) NEW and BE EASY TX Serial Number................................... : 0251 Trade Mark....................................... : SEAV Manufacturer.....................................: SEAV S.r.l. Via S. Sabino, 34 60027 Osimo - (Ancona) Italy Rating’s............................................. : 12VDC - 25mA Operating temperature range............ : From -20°C to +70°C Equipment information Equipment category.......................... : Transmitter of a control signal used for door openers. Classification of the equipment........ : Intentional Radiator Tested for IT power system.............. : No Test specification Applicable standard.......................... : FCC CFR 47 - Part 15 - Subpart C - § 15.231 Additional installation requirements : No Test results Summary of test results..................... : COMPLIANT Date: February 7, 2003 FCC ID: QUSTXSNEW Test report No: 03SV001EM-R01 Page 2 of 14 CiaoLab Technologies Standard Compliance Services General Remarks The test results presented in this report related only to the item tested. This test report shall not be reproduced except in full without the written approval of the testing laboratory. As stated in FCC §2.902: Verification attaches to all items subsequently marketed by the manufacturer or importer which are identical as defined in §2.908 to the sample tested and found acceptable by the manufacturer. In order to clarify the identical concept the §2.908 states: As used in this subpart the term identical means identical within the variation that can be expected to arise as a result of quantity production techniques. General Information of the Appliance Manufacturer SEAV S.r.l. Via S. Sabino, 34 60027 Osimo (Ancona) - Italy Applicant for Certification SEAV S.r.l. Via S. Sabino, 34 60027 Osimo (Ancona) - Italy FCC ID QUSTXSNEW Official of the Responsible party for Certification Name Guido Cerioni Research and Development Manager Signature .................................... Description of the Appliance The TXS 3 NEW device allows remote control of electric and electronic equipment, and it’s mainly used for automatic entry control (e.g. door - gate opener applications) where remote control via a radio coded command is required. The TXS 3 NEW remote control has to be considered the master model of the product series because it was designed first and in a complete way. TXS 2 NEW, TXS 1 NEW e BE EASY TX models differ from master model just for some hardware level changes. The products TXS 2 NEW, TXS 1 NEW e BEEASY TX are derivatives of the master model TXS 3 NEW. This difference consists in the lack of push buttons for coded data transmission. TXS 2 NEW e BE EASY TX models can just transmit two 12 bits codes. TXS 1 NEW model can just transmit one 12 bits code. The BE EASY TX derivative model is equal to TXS 2 NEW model except for plastic box. Date: February 7, 2003 FCC ID: QUSTXSNEW Test report No: 03SV001EM-R01 Page 3 of 14 CiaoLab Technologies Standard Compliance Services The appliance submitted to test (TXS 3 NEW) is the master model of a family of devices, the unit tested is equipped with three push buttons for coded data transmission, the other products (TXS 2 NEW and TXS 1 NEW) are equipped respectively with two and a single push buttons. The unit BE EASY TX use the same printed circuit board of the TXS 2 NEW mounted inside a different plastic box. In the following pictures is possible to see the four units subject to certification. The top side and the bottom side of TXS _ NEW units The three TXS _ NEW units opened, it is possible to see the electronic boards that are identical except the push buttons The top side and the bottom side of BE EASY TX The BE EASY TX unit opened, it is possible to see the electronic board that is identical to TXS 2 NEW. Date: February 7, 2003 FCC ID: QUSTXSNEW Test report No: 03SV001EM-R01 Page 4 of 14 CiaoLab Technologies Standard Compliance Services General Consideration of the Test Subject of this test report is the master model of the family of equipments, all other models must be considered as a subset of the master model. All the models The appliance intentionally generate an RF signal at frequency of 433,908000MHz, because of this it is classified under the Intentional Radiator Category and in conformity to the requirements of FCC Part 15 Subpart A §15.201, it is subject to “CERTIFICATION” procedure. As defined in FCC Part 15 Subpart C §15.207 (d) measurements to demonstrate compliance to conducted limits are not required for devices which only employ battery power for operation and which do not operate from AC power lines or contain provision for operation while connected to the AC power lines. Being our apparatus powered by a 12VDC alkaline battery, this measurement does not apply. The appliance generate the fundamental RF signal at 433,908000MHz so in accordance to FCC Part 15 Subpart A §15.33 (a)(1) the frequency range for radiated noise emission is from 30MHz to 4.34GHz. Because of the characteristics of the RF transmitted signal, frequency of 433908000.000Hz, the application of the equipment, mainly used for automatic entry control as a doo…

Text truncated - open the document above for the full version.

Test Setup Photo