QUX-NTT-830-2Nurse Tracking Tag

3M Resident Monitoring 7170 W. Donges Bay Road Toll Free: 800-606-0661 Mequon, WI 35092 Office: 414-358-8200 Fax: 414-358-8100 www.3m.com/residentmonitoring Copyright  2012 all rights reserved This document contains information that is proprietary to Attenti Ltd. No part of this publication may be reproduced in any form whatsoever without prior written approval by Attenti. Staff Card USER MANUAL NTT-830 Nurse Tracking Tag 3M Resident Monitoring Staff Card User Manual Page: 2 of 5 TABLE OF CONTENTS 1 Foreword............................................................................................................................................................ 3 2 Product manual ................................................................................................................................................. 3 2.1 Tracking Tag ........................................................................................................................................... 3 2.1.1 Deactivated mode....................................................................................................................... 3 2.1.2 Reset (Standby) Mode ............................................................................................................... 3 2.1.3 Active Mode ................................................................................................................................ 3 2.2 Summary of SC Tracking Modes ............................................................................................................ 4 2.3 Low Battery ............................................................................................................................................. 4 3 FCC Notices ...................................................................................................................................................... 5 3M Resident Monitoring Staff Card User Manual Page: 3 of 5 1 FOREWORD The RFID Staff Card is a device designed to be allocated to nurses in the area monitored by the AMS system. The tag contains both a passive RFID circuit as well as an active transmission circuit, allowing the system to capture when and which staff responded to a nurse call event. 2 PRODUCT MANUAL 2.1 Tracking Tag The SC will have 3 main stages: • Deactivated mode • Reset (Standby) Mode • Active Mode 2.1.1 Deactivated mode When deactivated, the SC shall not send any sanity transmissions nor shall it monitor motion. The SC shall leave the factory in this mode. Active/Rest
Deactivated • Press and hold down the SC's button for 5 seconds; at the end of the 5 seconds, the LED shall be lit (steady LED) for 5 seconds. • While the LED is lit, press the button three times; the LED flashes for 3 seconds to indicate that the SC is about to shut down. OR • After 12 hours without motion, the SC shall automatically deactivate. Note: Before the SC is deactivated, it shall send a transmission to the AMS to indicate that it has been manually deactivated (as opposed to destroyed or lost). 2.1.2 Reset (Standby) Mode In Rest mode, the SC shall transmit once every 15 minutes for a period of 1 hour. After 1 hour, the SC shall transmit once every hour. Deactivated
Rest Mode: • Press and hold down the button for 5 seconds Active
Rest Mode • No motion detected by the SC for 2 minutes. 2.1.3 Active Mode During Active mode, the device shall transmit a signal once every 18 – 22 seconds. Rest
Active Mode • Motion is detected by the SC. 3M Resident Monitoring 2.2 Summary of SC Tracking Modes Figure SC Status Low battery Deactivated → Rest Mode Rest/Active Mode → Deactivated 2.3 Low Battery The SC shall send a "Low Battery" signal with every transmission when the battery has approximately (but no less than) 2 weeks until the transmitter is rendered non When a "Low Battery" condition is present, the Low Battery LED indicator shall flash once every 10 seconds. 3M Resident Monitoring Staff Card User Manual Page: 4 of 5 SC Tracking Modes Figure 1: Transition between Modes LED Indication Flashes once every 10 seconds On while button is pressed, flashing for 3 seconds to indicate that activation is successful. On while the button is pressed, flashing for 3 seconds to indic deactivation is successful. The SC shall send a "Low Battery" signal with every transmission when the battery has approximately (but no less than) 2 weeks until the transmitter is rendered non-functional. on is present, the Low Battery LED indicator shall flash once every 10 seconds. User Manual button is pressed, flashing for 3 seconds to indicate that the button is pressed, flashing for 3 seconds to indicate that The SC shall send a "Low Battery" signal with every transmission when the battery has approximately (but no on is present, the Low Battery LED indicator shall flash once every 10 seconds. 3M Resident Monitoring Staff Card User Manual Page: 5 of 5 3 FCC NOTICES This note is applicable to the American Staff Card NOTE The Staff Card complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits of the Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses and can radiate radio frequency energy and, if installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by o…

Text truncated - open the document above for the full version.

3M Resident Monitoring 2 Habarzel St., +972 3 767 1900 Office P.O. Box 13236 +972 3 767 1901 Fax Tel-Aviv 61131, Israel www.3m.com/residentmonitoring 19.06.2012 NTT-830 / NTT-830-2 - Block Diagram

3M Resident Monitoring 2 Habarzel St., +972 3 767 1900 Office P.O. Box 13236 +972 3 767 1901 Fax Tel-Aviv 61131, Israel www.3m.com/residentmonitoring 19.06.2012 FCC Confidentiality Form Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Gentlemen, This letter is to comply with Section 0.457(d)(2)(i) and 0.459 pertaining to confidential material. HomeFree would like the following documents regarding this submission for FCC ID: QUX-NTT-830-2 to be kept confidential. • Permanent Confidentiality: Schematics • Short-term Confidentiality (180 days): Installation Manual The above material contains trade secrets or technical data, which would customarily be guarded from competitors. We do not want this document to be accessible to the general public. Sincerely, Shai Avigdori Director, Quality Assurance

3M Resident Monitoring 2 Habarzel St., +972 3 767 1900 Office P.O. Box 13236 +972 3 767 1901 Fax Tel-Aviv 61131, Israel www.3m.com/residentmonitoring 19.06.2012 External Pictures NTT-830-2

3M Resident Monitoring 2 Habarzel St., +972 3 767 1900 Office P.O. Box 13236 +972 3 767 1901 Fax Tel-Aviv 61131, Israel www.3m.com/residentmonitoring 19.06.2012 Label Location QUX-NTT-830-2 / QUX-NTT-830

3M Resident Monitoring 2 Habarzel St., +972 3 767 1900 Office P.O. Box 13236 +972 3 767 1901 Fax Tel-Aviv 61131, Israel www.3m.com/residentmonitoring 19.06.2012 Internal Pictures NTT-830

3M Resident Monitoring 2 Habarzel St., +972 3 767 1900 Office P.O. Box 13236 +972 3 767 1901 Fax Tel-Aviv 61131, Israel www.3m.com/residentmonitoring 19.07.2012 NTT – 830 Nurse Tracking Tag Operational Description The Nurse Tracking Tag is a small transmitter that shall be designed to be allocated to nurse to the area monitored by the AMS system. The device comprises a printed circuit board (PCB) that includes a RF transceiver module with an integral antenna, microcontroller that controls its operation and RFID tag for identification. The NTT-830 has one RF channel (318MHz, 433MHz) over which it communicates with its monitoring system. The RFID tag is read from Pull cord 840 The unit is powered by an internal 3V Lithium battery. The NTT – 830 shall be stored in a specific location when not in use (e.g. a cupboard or drawer). When a nurse arrives at work, she should activate a NTT. The NTT allocate nurses in order to track their location during the work. The NTT – 830 include an accelerometer that enable it to sense that the tracked nurse is in motion and generate a "Motion" transmissions event. In this mode device transmit variably once approximately every 18-22 seconds (non-periodic). If 2 minutes have not motion detection device return in standby mode. In standby mode the NTT transmit RF sanity message once every 15 minutes during first hour, after that, transmit sanity once every one hour in order to indicate that the tag is functional. When the nurse goes to room equipped with Pull Cord 840 she should put NTT over PC- 840. The PC-840 will read RFID tag and the Pull cord transmit “Nurse Presence” identification with NTT ID to AMS system. When the nurse leaves room she should put again NTT over PC-840. In this case the Pull Cord will read RFID tag and transmits “Nurse Left” for identification with NTT ID. At the end of the work, the nurse shall deactivate NTT. Periodic transmissions on NTT for signal integrity occurs only in standby mode. The maximum duration within the first hour: 4 signals (once every 15 minutes) => 4 X 6 ms (max.) = 24 ms The maximum duration after one hour: 1 transmission per hour => 1 X 6ms = 6ms

Test Report E115160.03 3M Resident Monitoring Ltd. Page 1 of 38 FCC ACC M Ver 1.1 05Mayl 2000 DATE: 22 July 2012 I.T.L. (PRODUCT TESTING) LTD. FCC Radio Test Report for 3M Resident Monitoring Ltd. Equipment under test: Nurse Tracking Tag NTT-830-2 Written by: _____________________________ A Ruta , Documentation Approved by: For/__________________________ A. Sharabi, Test Engineer Approved by: _____________________________ I. Raz, EMC Laboratory Manager This report must not be reproduced, except in full, without the written permission of I.T.L. (Product Testing) Ltd. This report relates only to items tested. Test Report E115160.03 3M Resident Monitoring Ltd. Page 2 of 38 FCC ACC M Ver 1.1 05Mayl 2000 Measurement/Technical Report for 3M Resident Monitoring Ltd. Nurse Tracking Tag NTT-830-2 FCC ID:QUX-NTT-830-2 IC: 4306B-NTT8302 This report concerns: Original Grant: x Class I change: Class II change: Equipment type: Part 15 Security/Remote Control Transceiver 47CFR15 Section 15231 (a-d) Measurement procedure used is ANSI C63.4-2003. Application for Certification: prepared by: Shai Avigdori 3M Resident Monitoring Ltd. 2 Habarzel St. Tel-Aviv, 61131 Israel Tel: +972-3- 767-1700 Fax: +972-3- 767-1701 e-mail: [email protected] Test Report E115160.03 3M Resident Monitoring Ltd. Page 3 of 38 FCC ACC M Ver 1.1 05Mayl 2000 TABLE OF CONTENTS 1. GENERAL INFORMATION ------------------------------------------------------------------------------- 4 1.1 Administrative Information ................................................................................. 4 1.2 List of Accreditations ......................................................................................... 5 1.3 Product Description ........................................................................................... 6 1.4 Test Methodology .............................................................................................. 6 1.5 Test Facility ....................................................................................................... 6 1.6 Measurement Uncertainty ................................................................................. 6 2. SYSTEM TEST CONFIGURATION --------------------------------------------------------------------- 7 2.1 Justification ........................................................................................................ 7 2.2 Special Accessories .......................................................................................... 7 2.3 Equipment Modifications ................................................................................... 7 2.4 Configuration of Tested System ........................................................................ 7 3. RADIATED MEASUREMENT TEST SET-UP PHOTO -------------------------------------------- 8 4. AVERAGE FACTOR CALCULATION ----------------------------------------------------------------- 10 4.1 Test Equipment Used ...................................................................................... 12 5. PERIODIC OPERATION ---------------------------------------------------------------------------------- 13 5.1 Specification .................................................................................................... 13 5.2 Requirements .................................................................................................. 13 5.3 Test Results..................................................................................................... 13 5.4 Test Equipment Used ...................................................................................... 17 6. FIELD STRENGTH OF FUNDAMENTAL ------------------------------------------------------------ 18 6.1 Test Specification ............................................................................................ 18 6.2 Test Procedure ................................................................................................ 18 6.3 Test Results..................................................................................................... 18 6.4 Test Instrumentation Used, Field Strength of Fundamental ............................ 22 7. RADIATED EMISSION, 9 KHZ – 30 MHZ ------------------------------------------------------------ 23 7.1 Test Specification ............................................................................................ 23 7.2 Test Procedure ................................................................................................ 23 7.3 Test Results..................................................................................................... 23 7.4 Test Equipment Used, Radiated Measurements............................................. 24 7.5 Field Strength Calculation ............................................................................... 24 8. SPURIOUS RADIATED EMISSION-------------------------------------------------------------------- 25 8.1 Test Specification ............................................................................................ 25 8.2 Test Procedure ................................................................................................ 25 8.3 Test Results..................................................................................................... 26 8.4 Test Equipment Used, Radiated Measurements............................................. 28 9. BANDWIDTH ------------------------------------------------------------------------------------------------ 29 9.1 Test procedure ................................................................................................ 29 9.2 Test Results..................................................................................................... 30 10. APPENDIX A - CORRECTION FACTORS ----------------------------------------------------------- 31 10.1 Correction factors for CABLE ......................................................................... 31 10.2 Correction factors for CABLE .............…

Text truncated - open the document above for the full version.

3M Resident Monitoring 2 Habarzel St., +972 3 767 1900 Office P.O. Box 13236 +972 3 767 1901 Fax Tel-Aviv 61131, Israel www.3m.com/residentmonitoring 19.06.2012 NTT-830-2 Test Setup Photographs