QV7-GC88752-51R/C CAR

T T w w i i s s t t e e r r C C a a r r Battery safety information Using the vehicle Thank you for purchasing one of our toy products. To ensure that you get the most out of your new purchase, please read these instructions carefully before using the toy for the first time. They contain important information on how to operate the product. Inserting the remote control batteries Remote control 1. Check the ON/OFF switch is in the “OFF” position. 2. Use a screwdriver to loosen the screw. 3.Remove the battery cover. · Please recharge with the dedicated USB delivered by the original factory. Never use broken USB or USB of other brands. · Please do not overcharge the battery. When the battery is fully recharged, please pull out the charger. · Please do not recharge on the surface of the objects near inflammable things(carpet, wood floor,solid wood furniture, etc.) or of conductive things. While recharging, please keep the battery within the range of visibility. 1. The batteries must only be charged under adult supervision. 2. Before charging the batteries, remove the battery compartment from the vehicle chassis. 3.Remove empty batteries from the vehicle and remote control. 4. Ensure that the vehicle is switched off before inserting the batteries. 5. Install the battery according to the instruction inside the battery box. Make sure not to confuse the positive and negative polarity of the battery. 6. Do not attempt to charge non-rechargeable batteries. 7.Do not short circuit the battery terminals. 8. If you do not plan to use the vehicle for an extended period, remove the batteries from the vehicle and remote control to prevent leakage. 9. Do not throw batteries into open flames, as this may cause them to explode or leak. 10.Do not mix old and new batteries or batteries from different manufacturers. 11.Only use batteries from recommended or reputable manufacturers. 12.Regularly inspect the batteries for signs of leakage. 13. It is suggested not to use more than 3 batteries for one single play. 14. If leaking occurs in the battery, please avoid touching the liquid with the skin and eyes.If it touches the skin, please clean the skin with soap and clean water at once. If it touches the eyes, please wash the eyes with a lot of cold water at once and see the doctor right away. 15. This equipment is composed of electronic components and battery. The electric appliance garbage should be given special care according to the local requirements for garbage disposal. 16. Keep this instruction manual in a safe place for future reference. It contains important information on how to use the product safely. · Remove the batteries when you do not plan to use the toy for an extended period. 4. According the polarity indicated inside in the remote control. Put the 2*AAA battery into the battery compartment. 5. Put the battery cover back and tighten the screw. Note: If break down occ urs in the product, please take out the battery for one minute, and then reinstall it. If the break down still exists, pleas e replace the battery. The battery can only be installed by the adults. 2X1.5V“AAA” Sketch Map of Installed Battery in the Remote Control · Use a damp cloth to wipe the vehicle clean. · Do not expose the toy to high temperatures, moisture or direct sunlight. · Do not immerse the toy in water, as this may damage the electrical components. ·If the wheel is too dirty or rolls inflexibly, this may influence the operation experience. Please check it and clear up the foreign matters. · When the wheels of remote control car is rolling, Do not touch it in order to avoid injury of yourself or damage of the car. · Please do not play by the road or in dangerous places in case of accidents. · Avoid operating the vehicle in the rain or grinding the remote control vehicle over the puddle · Connect the USB charger to USB output on computer or AC/DC adaptor,then insert the car charger plug to the USB wire charger.(Make sure in a correct polarity) · A full charge takes 70 minutes. When charging the LED indicator turns into red,when charging is complete, the LED indicator stays off. · Regularly inspect the toy, battery charger, charging cable, connectors and other components for signs of damage. In the event of any damage, discontinue use and send the parts for repair. · In case of abnormal responses such as suspicious peculiar smell, noise or smog in the charger,please remove the power supply at once. Indication Gravity Induction in case of breakdown. ·Avoid operating the vehicle alongside the river, lake or pond in case the remote control or remote control vehicle fall into the water. · Please take out the batteries from remote control when not using. Charging port ON/OFF ON/OFF Transform Demo 1 lamp Control bar Demo 2 Demo 3 Mode Switching ·Demo 1：Short press on Demo 1 key for a variety of functional demonstrations. (Different Demo keys have different music). ·Demo 2：Short press on Demo 2 key for a variety of functional demonstrations. (Different Demo keys have different music). ·Demo 3：Short press on Demo 3 key for a variety of functional demonstrations. (Different Demo keys have different music). ·Transform：Short press Transform key , the car will transform. ·Mode Switch：Short press “Mode” key to switch the mode of car, the car will change from 360degree rotation to left-right moving. ·Control level：Short press the control level to change the sound effect of the car, please check the operation instruction to see more functions. · Switch on the vehicle using the ON/OFF switch. · Switch on the vehicle ON/OFF switch,make the frequency of the remote control and remote control vehicle match each other,then you can operate the remote control vehicle. · Switch off the vehicle and remote control after use. ·The playing time is about 35 mins. ·The control rang is about 40 meters, if out of 40 meters rang , it may lose control. Caution： In order to avoid losing the remote control vehicle or making it lose control, follow the following …

Text truncated - open the document above for the full version.

GUANGDONG SYMA MODEL AIRCRAFT INDUSTRIAL CO., LTD. Date: 2021-6-30 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID:QV7-GC88752-51 To whom it may concern: We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch and Keny Xu in SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with GUANGDONG SYMA MODEL AIRCRAFT INDUSTRIAL CO., LTD. This authorization is valid until further written notice from the applicant. Print Name: Title:Manager Signature: On behalf of Company: GUANGDONG SYMA MODEL AIRCRAFT INDUSTRIAL CO., LTD. Telephone:0754-86381898 E-mail: [email protected]

GUANGDONG SYMA MODEL AIRCRAFT INDUSTRIAL CO., LTD. TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: Confidentiality Request regarding application for FCC ID: QV7-GC88752-51 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Sincerely, Print Name: Title:Manager Signature: On behalf of Company: GUANGDONG SYMA MODEL AIRCRAFT INDUSTRIAL CO., LTD. Telephone:0754-86381898 E-mail: [email protected]

Applicant Declaration Applicant Declaration Rev:0.0 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Legal Business Name GUANGDONG SYMA MODEL AIRCRAFT INDUSTRIAL CO., LTD. Address No. 2 West Xingye Road Laimei Industrial Area,Chenghai Shantou China Grantee Code QV7 FCC ID QV7-GC88752-51 Authorized Contact Name Ivan Chen Contact Email [email protected] Contact Phone 0754-86381898 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare; a) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. b) in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for: (1) labeling the equipment with the exact FCC ID as specified in this application, (2) compliance statement labeling pursuant to the applicable rules, (3) compliance of the equipment with the applicable technical rules, c) if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC’s technical requirements. d) in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. e) in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements. (1) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. (2) the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. (3) the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a “party” for these purposes. g) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Applicant Signature: Date:2021-6-30 Print Name: Title: Manager *NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 1 of 4 External Photos for SZCR2105021095ET FCC ID: QV7-GC88752-51 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 2 of 4 1 EUT Constructional Details SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 3 of 4 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 4 of 4

FCC ID : QV7-GC88752-51 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Label size: 3cm*5cm

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 1 of 3 Internal Photos for SZCR2105021095ET FCC ID: QV7-GC88752-51 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 2 of 3 1 EUT Constructional Details SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 3 of 3

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZCR210502109502 Page: 1 of 43 Keny Xu EMC Laboratory Manager TEST REPORT Application No.: SZCR2105021095ET Applicant: GUANGDONG SYMA MODEL AIRCRAFT INDUSTRIAL CO., LTD. Address of Applicant: No. 2 West Xingye Road Laimei Industrial Area, Chenghai Shantou City, Guangdong, China Manufacturer: GUANGDONG SYMA MODEL AIRCRAFT INDUSTRIAL CO., LTD. Address of Manufacturer: No. 2 West Xingye Road Laimei Industrial Area, Chenghai Shantou City, Guangdong, China Factory: GUANGDONG SYMA MODEL AIRCRAFT INDUSTRIAL CO., LTD. Address of Factory: No. 2 West Xingye Road Laimei Industrial Area, Chenghai Shantou City, Guangdong, China Equipment Under Test (EUT): EUT Name: R/C CAR Model No.: S2, TG1007, TG1008, S5, S5H, S8, S39-1, S39H, S107G, S107H, S109G, S111G, X4, X5, X5A, X5C, X5S, X5SC, X5SW, X5HC, X5HW, X5U, X5UC- 1, X5UW, X5UW(720P)-1, X5UW(720P), X5UW-D, X8HW(720P), X8SW(720P), X8SW(720P)-D, X8PRO, X13, X15, X15W, X15A, X15T, X18, X20, X20-S, X20W, X20P, X21, X21W, X22SW, X22W, X23, X23W, X25W, X25PRO, X26, X27, X30, W1, W1PRO, Z1, Z3, X54HW, X56W, X56W-P, X57, TF1001, TF1002, TF1003, TG1001, TG1006 TG1003, TG1004S, TG1004T, TG1004C, TG1005, K01, K02, K03, X300, X400, S100, S200, S300, T100, T200, X30PRO, W3, W3PRO, X31, Q1, Q2, Q5, S2, Z4, Z4W, Z5, Z5W, X600, X600W, X700, X700W, X650, X500PRO, X32, Z6, Z7, Z7W, S37H, S37, TG1002, S1 ♣ ♣ Please refer to section 2 of this report which indicates which model was actually tested and which were electrically identical. FCC ID: QV7-GC88752-51 Standard(s) : 47 CFR Part 15, Subpart C 15.249 Date of Receipt: 2021-05-19 Date of Test: 2021-05-19 to 2021-06-01 Date of Issue: 2021-06-07 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZCR210502109502 Page: 2 of 43 Revision Record Version Chapter Date Modifier Remark 01 2021-06-07 Original Authorized for issue by: Gebin Sun/Project Engineer Eric Fu/Reviewer SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZCR210502109502 Page: 3 of 43 2 Test Summary Radio Spectrum Technical Requirement Item Standard Method Requirement Result Antenna Requirement 47 CFR Part 15, Subpart C 15.249 N/A 47 CFR Part 15, Subpart C 15.203 Pass Radio Spectrum Matter Part Item Standard Method Requirement Result 20dB Bandwidth 47 CFR Part 15, Subpart C 15.249 ANSI C63.10 (2013) Section 6.9 47 CFR Part 15, Subpart C 15.215 Pass Field Strength of the Fundamental Signal (15.249(a)) ANSI C63.10 (2013) Section 6.5&6.6 47 CFR Part 15, Subpart C 15.249(a) Pass Restricted Band Around Fundamental Frequency ANSI C63.10 (2013) Section 6.10.5 47 CFR Part 15, Subpart C 15.205 & 15.249(d) & 15.209 Pass Radiated Emissions Below 1GHz ANSI C63.10 (2013) Section 6.4&6.5 47 CFR Part 15, Subpart C 15.209 & 15.249 (a),(d) Pass Radiated Emissions Above 1GHz ANSI C63.10 (2013) Section 6.6 47 CFR Part 15, Subpart C 15.209 & 15.249 (a),(d) Pass Declaration of EUT Family Grouping: Model No.: S2, TG1007, TG1008, S5, S5H, S8, S39-1, S39H, S107G, S107H, S109G, S111G, X4, X5, X5A, X5C, X5S, X5SC, X5SW, X5HC, X5HW, X5U, X5UC-1, X5UW, X5UW(720P)-1, X5UW(720P), X5UW-D, X8HW(720P), X8SW(720P), X8SW(720P)-D, X8PRO, X13, X15, X15W, X15A, X15T, X18, X20, X20-S, X20W, X20P, X21, X21W, X22SW, X22W, X23, X23W, X25W, X25PRO, X26, X27, X30, W1, W1PRO, Z1, Z3, X54HW, X56W, X56W-P, X57, TF1001, TF1002, TF1003, TG1001, TG1006 TG1003, TG1004S, TG1004T, TG1004C, TG1005, K01, K02, K03, X300, X400, S100, S200, S300, T100, T200, X30PRO, W3, W3PRO, X31, Q1, Q2, Q5, S2, Z4, Z4W, Z5, Z5W, X600, X600W, X700, X700W, X650, X500PRO, X32, Z6, Z7, Z7W, S37H, S37, TG1002, S1 Only the model S2 was tested. According to the declaration from the applicant, the electrical circuit design, layout, components used, internal wiring and functions were identical for the above models, with only difference on colour and packaging. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZCR210502109502 Page: 4 of 43 3 Contents Page 1 COVER PAGE ..................................................................................................................................... 1 2 TEST SUMMARY ................................................................................................................................. 3 3 CONTENTS ......................................................................................................................................... 4 4 GENERAL INFORMATION .................................................................................................................. 6 4.1 DETAILS OF E.U.T. ......................................................................................................................... 6 4.2 DESCRIPTION OF SUPPORT UNITS .................................................................................................... 7 4.3 MEASUREMENT UNCERTAINTY ......................................................................................................... 7 4.4 TEST LOCATION ............................................................................................................................. 8 4.5 TEST FACILITY ............................................................................................................................... 8 4.6 DEVIATION FROM STANDARDS ......................................................................................................... 8 4.7 ABNORMALITIES FROM STANDARD CONDITIONS ................................................................................. 8 5 EQUIPMENT LIST ............................................................................................................................... 9 6 RADIO SPECTRUM TECHNICAL REQUIREMENT ............................................................................11 6.1 ANTENNA REQUIREMENT .................…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 1 of 3 Setup Photos for SZCR2105021095ET FCC ID: QV7-GC88752-51 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 2 of 3 1 Photographs Field Strength of the Fundamental Signal (15.249(a)) Radiated Emissions Below 1GHz SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 3 of 3 Radiated Emissions Above 1GHz