QV7-GC88752-52STUNT SPEEDER

6+ 1.5V“AA” 1.5V“AA” USB The materials, specifications, parts and packaging mentioned in this manual are for reference purposes only. We are not responsible for any changes made to this printed material, nor are we able to inform customers of any updates or changes. Please refer to our website: R3VOLT.COM for the latest information. Important safety information Thank you for buying this REVOLT item. To ensure that you operate the vehicle correctly, please read these instructions carefully before first use and store them in a safe place for future reference. Safety information *Keep the smaller-sized accessories out of the reach of children. *Do not store batteries in a hot environment (e.g. near open flames or a heating device). *Children must be supervised by an adult when operating the vehicle. The vehicle should always remain within the line of sight of the driver (or instructor). *Do not recharge non-rechargeable batteries. When installing or changing the batteries, ensure that they are connected in the correct polarity. Do not mix old and new batteries or different types of batteries. *Do not short circuit the battery terminals. *If you do not plan to use the vehicle for at least 10 days, discharge the battery to 40%-50% (i.e. if the battery is fully charged, drive the vehicle for half of the total driving time). This helps to prolong the lifespan of the battery. *You must only use the charging cable provided. Disconnect the model from the charging cable before cleaning . Regularly inspect the charging cable’s wires, plug socket, outer casing and other accessories to ensure that they are not damaged.If there are any signs of damage, discontinue use immediately until the fault has been repaired. *After use, ensure that the vehicle and remote control are switched off and remove the batteries in the remote control. *The packaging and this manual contain important information and should be kept in a safe place for future reference. Repair and maintenance *Clean the product regularly with a clean, soft cloth. *Avoid exposing the product to direct sunlight or heat. *Do not submerge the product in water, as this may damage the electrical components. About this product Specifications Remote controlled vehicle Weight 64.5g (including battery) Dimensions 13.5x8x5 cm Remote control range 15-20m Operating temperature 0 to 40 °C Battery 3.7V 200mAh rechargeble battery (included) Remote control Operating frequency 2.4 GHz Operating temperature 0 to 40 °C Battery Requirements 2x AA 1.5V Batteries (not included) Ramp Weight 25g Dimensions 19x11x7.5cm Safety information: 1.Switch off the product before charging the battery, and then connect the USB charging cable (ensure that the charging connector is connected in the correct orientation). 2.Connect the USB charging cable to a mobile USB charger or computer USB port. The indicator light on the USB charging cable will turn on to indicate that charging is in progress and switch off when charging is complete. 3.Pairing instructions: Switch on the vehicle. The indicator light will start to flash. Switch on the remote control and wait for the remote control indicator to flash. The devices will pair automatically and the indicator lights will switch off simultaneously when pairing is complete. After use, switch off the vehicle and remote control to preserve battery power. Charging the vehicle battery Installing the remote control batteries LED indicator Important: only use the charging cable provided. Charging the built-in vehicle battery charging socket Operating the vehicle and remote control Programming a sequence of movements 1.The remote control can be programmed to perform a sequence of movements. After pairing the vehicle with the remote control, enter programming mode by holding down the programming button for 2 seconds until the LED indicator starts to flash. Example: Forwards + turn left + turn right, reverse + turn left + turn right, forwards + reverse + turn left. You can program up to 14 movements. Fig 1. Hold down the programming button to enter programming mode Fig. 2 Programming a sequence of movements Turn right Turn left Forwards Increase speed Programming button Flashing indicator 2.After programming the desired movements, press the programming button to exit programming mode. The LED indicator will switch off. 3.To perform the programmed sequence of movements, press the programming button. 4. To reprogram the sequence of movements, follow the instructions in figure 1. Note: The remote control will automatically exit programming mode after 8 seconds of inactivity. If you entered a sequence a movements, the sequence will be automatically saved. If you did not enter a sequence of movements, the remote control will automatically retain the most recently programmed sequence. To stop the vehicle when it is performing your programmed sequence of movements, move the forwards, reverse, left or right controls. If the remote control batteries are depleted when you attempt to program a sequence of movements, your sequence will not be saved. If this occurs, replace the batteries and try again. Address: Intersection of Xingye Road No. 2 (West side) and Xingye Road (North side), Laimei Industrial Park, Chenghai District, Shantou, Guangdong Province, China Sales hotline: 0754-86980668, After-sales hotline: 0754-86395095 Fax: 0754-86395098 Zip code: 515800 The manufacturer the right to the final interpretation of this instruction manual. The vehicle will perform the programmed sequence of movements Fig. 3 Performing a programmed sequence of Programming mode Press the programming button again Programming button NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable prote- ction against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not \inst…

Text truncated - open the document above for the full version.

GUANGDONG SYMA MODEL AIRCRAFT INDUSTRIAL CO., LTD Date: 2021-05-11 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: QV7-GC88752-52 To whom it may concern: We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch and Keny Xu in SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with GUANGDONG SYMA MODEL AIRCRAFT INDUSTRIAL CO., LTD. This authorization is valid until further written notice from the applicant. Print Name: Title: Sale Director Signature: On behalf of Company: GUANGDONG SYMA MODEL AIRCRAFT INDUSTRIAL CO., LTD Telephone: 0754-86381898 E-mail: [email protected]

Date: 2021-05-11 To: Federal Communications Commission Office of Engineering and Technology Laboratory Division 7435 Oakland Mills Rd. Columbia MD 21046 From: GUANGDONG SYMA MODEL AIRCRAFT INDUSTRIAL CO., LTD Regarding: Confidentiality Request regarding application for FCC ID: QV7-GC88752-52 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby requests confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Print Name: Title: Sale Director Signature: On behalf of Company: GUANGDONG SYMA MODEL AIRCRAFT INDUSTRIAL CO., LTD Telephone: 0754-86381898 E-mail: [email protected]

Applicant Declaration Applicant Declaration Rev:0.0 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Legal Business Name GUANGDONG SYMA MODEL AIRCRAFT INDUSTRIAL CO., LTD Address NO.2 WEST XINGYE ROAD LAIMEI INDUSTRIAL AREA CHENG HAI Shantou China Grantee Code QV7 FCC ID QV7-GC88752-52 Authorized Contact Name Ivan Chen Contact Email [email protected] Contact Phone 0754-86381898 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare; a) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. b) in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for: (1) labeling the equipment with the exact FCC ID as specified in this application, (2) compliance statement labeling pursuant to the applicable rules, (3) compliance of the equipment with the applicable technical rules, c) if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC’s technical requirements. d) in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. e) in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements. (1) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. (2) the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. (3) the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a “party” for these purposes. g) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Applicant Signature: Date: 2021-5-11 Applicant Declaration Applicant Declaration Rev:0.0 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Print Name: Title: Sale Director *NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 1 of 4 External Photos for SZCR2105020871AT FCC ID: QV7-GC88752-52 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 2 of 4 EUT Constructional Details (EUT Photos) SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 3 of 4 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 4 of 4

FCC ID : QV7-GC88752-52 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Label size: 3cm*5cm

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 1 of 3 Internal Photos for SZCR2105020871AT FCC ID: QV7-GC88752-52 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 2 of 3 EUT Constructional Details (EUT Photos) SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 3 of 3

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZCR210502087102 Page: 1 of 40 Keny Xu EMC Laboratory Manager TEST REPORT Application No.: SZCR2105020871AT Applicant: GUANGDONG SYMA MODEL AIRCRAFT INDUSTRIAL CO., LTD Address of Applicant: NO.2 WEST XINGYE ROAD LAIMEI INDUSTRIAL AREA CHENGHAI SHANTOU GUANGDONG CHINA Manufacturer: GUANGDONG SYMA MODEL AIRCRAFT INDUSTRIAL CO., LTD Address of Manufacturer: NO.2 WEST XINGYE ROAD LAIMEI INDUSTRIAL AREA CHENGHAI SHANTOU GUANGDONG CHINA Factory: GUANGDONG SYMA MODEL AIRCRAFT INDUSTRIAL CO., LTD Address of Factory: NO.2 WEST XINGYE ROAD LAIMEI INDUSTRIAL AREA CHENGHAI SHANTOU GUANGDONG CHINA Equipment Under Test (EUT): EUT Name: STUNT SPEEDER Model No.: TG1007, S5, S5H, S8, S39-1, S39H, S107G, S107H, S109G, S111G, X4, X5, X5A, X5C, X5S, X5SC, X5SW, X5HC, X5HW, X5U, X5UC-1, X5UW, X5UW(720P)-1, X5UW(720P), X5UW-D, X8HW(720P), X8SW(720P), X8SW(720P)-D, X8PRO, X13, X15, X15W, X15A, X15T, X18, X20, X20-S, X20W, X20P, X21, X21W, X22SW, X22W, X23, X23W, X25W, X25PRO, X26, X27, X30, W1, W1PRO, Z1, Z3, X54HW, X56W, X56W-P, X57, TF1001, TF1002, TF1003, TG1001, TG1006, TG1003, TG1004S, TG1004T, TG1004C, TG1005, K01, K02, K03, X300, X400, S100, S200, S300, T100, T200, X30PRO, W3, W3PRO, X31, Q1, Q2, Q5, S2, Z4, Z4W, Z5, Z5W, X600, X600W, X700, X700W, X650, X500PRO, X32, Z6, Z7, Z7W, S37H, S37, TG1002, S1  Please refer to section 2 of this report which indicates which model was actually tested and which were electrically identical. FCC ID: QV7-GC88752-52 Standard(s) : 47 CFR Part 15, Subpart C 15.249 Date of Receipt: 2021-05-07 Date of Test: 2021-05-07 to 2021-05-24 Date of Issue: 2021-05-28 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZCR210502087102 Page: 2 of 40 Revision Record Version Chapter Date Modifier Remark 01 2021-05-28 Original Authorized for issue by: Gebin Sun/Project Engineer Eric Fu/Reviewer SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZCR210502087102 Page: 3 of 40 2 Test Summary Radio Spectrum Technical Requirement Item Standard Method Requirement Result Antenna Requirement 47 CFR Part 15, Subpart C 15.249 N/A 47 CFR Part 15, Subpart C 15.203 Pass Radio Spectrum Matter Part Item Standard Method Requirement Result 20dB Bandwidth 47 CFR Part 15, Subpart C 15.249 ANSI C63.10 (2013) Section 6.9 47 CFR Part 15, Subpart C 15.215 Pass Field Strength of the Fundamental Signal (15.249(a)) ANSI C63.10 (2013) Section 6.5&6.6 47 CFR Part 15, Subpart C 15.249(a) Pass Restricted Band Around Fundamental Frequency ANSI C63.10 (2013) Section 6.10.5 47 CFR Part 15, Subpart C 15.205 & 15.249(d) & 15.209 Pass Radiated Emissions ANSI C63.10 (2013) Section 6.4&6.5&6.6 47 CFR Part 15, Subpart C 15.209 & 15.249 (a),(d) Pass Declaration of EUT Family Grouping: Model No.: TG1007, S5, S5H, S8, S39-1, S39H, S107G, S107H, S109G, S111G, X4, X5, X5A, X5C, X5S, X5SC, X5SW, X5HC, X5HW, X5U, X5UC-1, X5UW, X5UW(720P)-1, X5UW(720P), X5UW-D, X8HW(720P), X8SW(720P), X8SW(720P)-D, X8PRO, X13, X15, X15W, X15A, X15T, X18, X20, X20- S, X20W, X20P, X21, X21W, X22SW, X22W, X23, X23W, X25W, X25PRO, X26, X27, X30, W1, W1PRO, Z1, Z3, X54HW, X56W, X56W-P, X57, TF1001, TF1002, TF1003, TG1001, TG1006, TG1003, TG1004S, TG1004T, TG1004C, TG1005, K01, K02, K03, X300, X400, S100, S200, S300, T100, T200, X30PRO, W3, W3PRO, X31, Q1, Q2, Q5, S2, Z4, Z4W, Z5, Z5W, X600, X600W, X700, X700W, X650, X500PRO, X32, Z6, Z7, Z7W, S37H, S37, TG1002, S1 Only the model TG1007 was tested, since according to the declaration from the applicant, the electrical circuit design, layout, components used, internal wiring and functions were identical for the above models, with only difference on colour and packaging. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZCR210502087102 Page: 4 of 40 3 Contents Page 1 COVER PAGE ..................................................................................................................................... 1 2 TEST SUMMARY ................................................................................................................................. 3 3 CONTENTS ......................................................................................................................................... 4 4 GENERAL INFORMATION .................................................................................................................. 5 4.1 DETAILS OF E.U.T. ......................................................................................................................... 5 4.2 DESCRIPTION OF SUPPORT UNITS .................................................................................................... 5 4.3 MEASUREMENT UNCERTAINTY ......................................................................................................... 6 4.4 TEST LOCATION ............................................................................................................................. 7 4.5 TEST FACILITY ............................................................................................................................... 7 4.6 DEVIATION FROM STANDARDS ......................................................................................................... 7 4.7 ABNORMALITIES FROM STANDARD CONDITIONS ................................................................................. 7 5 EQUIPMENT LIST ............................................................................................................................... 8 6 RADIO SPECTRUM TECHNICAL REQUIREMENT ............................................................................10 6.1 ANTENNA REQUIREMENT ................................................................................................................10 6.1.1 Test Requirement: .......................................…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 1 of 3 Appendix Photographs of Test Setup for SZCR2105020871AT FCC ID: QV7-GC88752-52 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 2 of 3 Test Setup Photo Field Strength of the Fundamental Signal (15.249(a)) Restricted Band Around Fundamental Frequency SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 3 of 3 Radiated Emissions Below 1GHz Radiated Emissions Above 1GHz