
Text extracted from the exhibit documents filed with the FCC. Open a document above to read the original.
BT4600 (IP Series) BT5600 (GPS Series) CDMA 1xEvDO Modems Product Manual BlueTree Wireless BT4600 and BT5600 CDMA 1xEvDO Modems Product Manual November 2005 UG-BT4600 & BT5600 CDMA BlueTree Wireless Data, Inc. 2425 46th Avenue Lachine, QC, Canada H8T 3C9 Tel: +1 (514) 422-9110 Toll Free: 1-877-422-9110 www.bluetreewireless.com Copyright © 2004/2005 by BlueTree Wireless Data, Inc. All Rights Reserved Printed in Canada BlueTree™, the BlueTree logo, and BlueVue™ are trademarks of BlueTree Wireless Data, Inc. All other trademarks are the property of their respective owners. Draft 1 BlueTree Wireless BT-4600/BT-5600 Product Manual 4 Patents Portions of this product are covered by some or all of the following patents: Declaration of Conformity FCC Compliance and Industry Canada Statement FCC ID: (TBD) Industry Canada: (TBD) The device complies with Part 15 of FCC rules and with ICES-003 of Industry Canada Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Caution: Unauthorized modifications or changes not expressly approved by BlueTree Wireless Data, Inc. could void compliance with regulatory rules, and thereby your authority to use this equipment. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer's instructions, may cause interference harmful to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Draft 1 BlueTree Wireless BT-4600/BT-5600 Product Manual 5 Warning: “Antenna must not exceed 3 dBi for Cellular band and 4 dBi for PCS band. This device must be used in mobile configurations. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 30 cm or 12 inches from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Users and Installers must be provided with antenna installation instruction and transmitter operating conditions for satisfying RF exposure compliance” Liability Notice While every effort has been made to achieve technical accuracy, information in this document is subject to change without notice and does not represent a commitment on the part of BlueTree Wireless Data, Inc., or any of its subsidies, affiliates, agents, licensors, or resellers. There are no warranties, express or implied, with respect to the content of this document. Safety Do not operate the BlueTree Wireless Data BT4600 or BT5600 modem in areas near medical equipment, where blasting is in progress, where explosive atmospheres may be present, or near any equipment that may be susceptible to any form of radio interference. Draft 1 BlueTree Wireless BT-4600/BT-5600 Product Manual 6 Contents Chapter 1: Introduction ......................................................... 7 Welcome................................................................................... 7 Customer Support ...................................................................... 7 Chapter 2: Product Description .............................................. 8 Overview .................................................................................. 8 Available Models ........................................................................ 8 Modem Features ........................................................................ 9 Operational Description ..............................................................10 Physical Description...................................................................12 Technical Specifications..............................................................17 Chapter 3: Installation Requirements .................................. 18 Cellular antenna........................................................................18 GPS antenna ............................................................................18 Serial cable ..............................................................................19 Ethernet cable ..........................................................................19 USB cable ................................................................................19 Power source............................................................................19 Mounting Hardware ...................................................................19 Wireless network account ...........................................................19 Chapter 4: Installing the Modem.......................................... 20 1) Unpacking the Modem............................................................20 2) Mounting the Modem .............................................................20 3) Installing the Cellular Antenna ................................................20 4) Installing the GPS Antenna .....................................................21 5) Installing the Power Cable ......................................................22 6) Connecting the Data Cables ....................................................24 7) Configuring the modem..........................................................25 8) Connecting to a wireless network using the serial port (DB9) .......25 9) Connecting to a wireless network using the Ethernet port (RJ45)..26 Appendix A: Warranty an…
Text truncated - open the document above for the full version.
BT-4600 Ev-DO IP vs. BT-5600 EV-DO GPS Variance Circuit Card View: Rear View: Front View:
REPORT NO: 04U3076-1 DATE: FEBRUARY 02, 2005 EUT: EMBEDDED WIRELESS RADIO MODEM FCC ID: N7N-EM5625D Page 40 of 54 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. 7.5. MAXIMUM PERMISSIBLE EXPOSURE LIMITS §1.1310 The criteria listed in Table 1 shall be used to evaluate the environmental impact of human exposure to radio-frequency (RF) radiation as specified in §1.1307(b), except in the case of portable devices which shall be evaluated according to the provisions of §2.1093 of this chapter. REPORT NO: 04U3076-1 DATE: FEBRUARY 02, 2005 EUT: EMBEDDED WIRELESS RADIO MODEM FCC ID: N7N-EM5625D Page 41 of 54 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. CALCULATIONS Given E = √ (30 * P * G) / d and S = E ^ 2 / 3770 where E = Field Strength in Volts/meter P = Power in Watts G = Numeric antenna gain d = Distance in meters S = Power Density in milliwatts/square centimeter Combining equations and rearranging the terms to express the distance as a function of the remaining variables yields: d = √ ((30 * P * G) / (3770 * S)) Changing to units of Power to mW and Distance to cm, using: P (mW) = P (W) / 1000 and d (cm) =100 * d (m) yields d = 100 * √ ((30 * (P / 1000) * G) / (3770 * S)) d = 0.282 * √ (P * G / S) where d = distance in cm P = Power in mW G = Numeric antenna gain S = Power Density in mW/cm^2 Substituting the logarithmic form of power and gain using: P (mW) = 10 ^ (P (dBm) / 10) and G (numeric) = 10 ^ (G (dBi) / 10) yields d = 0.282 * 10 ^ ((P + G) / 20) / √ S Equation (1) where d = MPE distance in cm P = Power in dBm G = Antenna Gain in dBi S = Power Density Limit in mW/cm^2 Equation (1) and the measured peak power is used to calculate the MPE distance. REPORT NO: 04U3076-1 DATE: FEBRUARY 02, 2005 EUT: EMBEDDED WIRELESS RADIO MODEM FCC ID: N7N-EM5625D Page 42 of 54 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. LIMITS From §1.1310 Table 1 (B), S = 1.0 mW/cm^2 RESULTS No non-compliance noted: NOTE: For mobile or fixed location transmitters, the minimum separation distance is 20 cm, even if calculations indicate that the MPE distance would be less. ModePower DensityOutputAntennaMPE LimitPowerGainDistance (mW/cm^2)(dBm)(dBi)(cm) 800MHz Celllar0.628.995.1019.08 1900 MHz PCS1.028.603.9011.89
Prediction of MPE limit at a given distance Blue Tree 5600 EV-DO Wireless Modem Equation from page 18 of OET Bulletin 65, Edition 97-01where: S = power density P = power input to the antennaG = power gain of the antenna in the direction of interest relative to an isotropic radiatorR = distance to the center of radiation of the antenna Maximum peak output power at antenna input terminal: 28.60 (dBm) Maximum peak output power at antenna input terminal: 724.4359601 (mW) Antenna gain(typical): 3.9 (dBi) Maximum antenna gain: 2.454708916 (numeric) Prediction distance: 20 (cm) Prediction frequency: 1900 (MHz) MPE limit for uncontrolled exposure at prediction frequency: 1 (mW/cm^2) Power density at prediction frequency: 0.353777 (mW/cm^2) Maximum allowable antenna gain: 8.412698554 (dBi) Margin of Compliance: 4.512698554 dB 2 4 R PG S π =
FCC CFR47 PART 22 SUBPART H AND PART 24 SUBPART E CERTIFICATION TEST REPORT FOR EMBEDDED WIRELESS RADIO MODEM MODEL NUMBER: EM5625D FCC ID: N7N-EM5625D REPORT NUMBER: 04U3076-1 ISSUE DATE: FEBRUARY 02, 2005 Prepared for SIERRA WIRELESS 2290 COSMOS CT. CARLSBAD CALIFORNIA 92009 U.S.A Prepared by COMPLIANCE ENGINEERING SERVICES, INC. d.b.a. COMPLIANCE CERTIFICATION SERVICES 561F MONTEREY ROAD, MORGAN HILL, CA 95037, USA TEL: (408) 463-0885 FAX: (408) 463-0888 REPORT NO: 04U3076-1 DATE: FEBRUARY 02, 2005 EUT: EMBEDDED WIRELESS RADIO MODEM FCC ID: N7N-EM5625D Page 2 of 54 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. Revision History Rev. Revisions Revised By 1 Revised user manual to allow max antenna’s gain of 5.1dBi in Cellular bands and 3.9dBi in PCS bands. Client 2 Revised report in MPE section based on max antenna’s gain Thu REPORT NO: 04U3076-1 DATE: FEBRUARY 02, 2005 EUT: EMBEDDED WIRELESS RADIO MODEM FCC ID: N7N-EM5625D Page 3 of 54 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS............................................................................................. 4 2. TEST METHODOLOGY .................................................................................................................. 5 3. FACILITIES AND ACCREDITATION .......................................................................................... 5 4. CALIBRATION AND UNCERTAINTY.......................................................................................... 5 4.1. MEASURING INSTRUMENT CALIBRATION ............................................................................. 5 4.2. MEASUREMENT UNCERTAINTY ............................................................................................... 5 5. EQUIPMENT UNDER TEST............................................................................................................6 5.1. DESCRIPTION OF EUT ..............................................................................................................6 5.2. MAXIMUM OUTPUT POWER .................................................................................................... 6 5.3. DESCRIPTION OF AVAILABLE ANTENNAS ............................................................................. 6 5.4. SOFTWARE AND FIRMWARE .................................................................................................... 6 5.5. WORST-CASE CONFIGURATION AND MODE......................................................................... 6 5.6. DESCRIPTION OF TEST SETUP ................................................................................................ 7 6. TEST AND MEASUREMENT EQUIPMENT ................................................................................ 9 7. LIMITS AND RESULTS ................................................................................................................. 10 7.1. OCCUPIED BANDWIDTH ........................................................................................................ 10 7.2. RF POWER OUTPUT.................................................................................................................17 7.3. SPURIOUS EMISSION AT ANTENNA TERMINAL................................................................... 20 7.4. FIELD STRENGTH OF SPURIOUS EMISSION ....................................................................... 35 7.5. MAXIMUM PERMISSIBLE EXPOSURE ................................................................................... 40 7.6. FREQUENCY STABILITY .......................................................................................................... 43 8. SETUP PHOTOS .............................................................................................................................. 46 REPORT NO: 04U3076-1 DATE: FEBRUARY 02, 2005 EUT: EMBEDDED WIRELESS RADIO MODEM FCC ID: N7N-EM5625D Page 4 of 54 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 561F MONTEREY ROAD, MORGAN HILL, CA 95037 USA TEL: (408) 463-0885 FAX: (408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. 1. ATTESTATION OF TEST RESULTS COMPANY NAME: SIERRA WIRELESS 2290 COSMOS CT. CARLSBAD CALIFORNIA 92009 U.S.A EUT DESCRIPTION: EMBEDDED WIRELESS RADIO MODEM MODEL: EM5625D SERIAL NUMBER: 12224500027 DATE TESTED: JANUARY 30 - FEBRUARY 01, 2005 APPLICABLE STANDARDS STANDARD TEST RESULTS FCC PART 22 SUBPART H NO NON-COMPLIANCE NOTED FCC PART 24 SUBPART E NO NON-COMPLIANCE NOTED Compliance Certification Services, Inc. tested the above equipment in accordance with the requirements set forth in the above standards. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Note: The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein. This document may not be altered or revised in any way unless done so by Compliance Certification Services and all revisions are duly noted in the revisions section. Any alteration of this document not carried out by Compliance Certification Services will constitute fraud and shall nullify the document. No part of this report may be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any government agency. Approved & Released For CCS By: Tested By: THU CHAN CHIN PANG AND VIEN TRAN EMC SUPERVISOR EMC TECHNICAINS COMPLIANCE CERTIFICATION SERVICES COMPLIANCE CERTIFICATION SERVICES REPORT NO: 04U3076-1 DATE: FEBRUARY 02, 2005 EUT: EMBE…
Text truncated - open the document above for the full version.
2425 46th Avenue · Lachine, Quebec · Canada
| # | Rule Parts | Frequency Range | Power Output | Emission | Tolerance |
|---|---|---|---|---|---|
| 2 | 22H | 824.7 MHz - 848.31 MHz | 793.00 mW | 1M40F9W | 2.5 ppm |

CDMA Modem
Equipment Class
PCB - PCS Licensed Transmitter
GSM/GPRS Wireless Modem
Equipment Class
PCB - PCS Licensed Transmitter
GSM/GPRS Wireless Modem
Equipment Class
PCB - PCS Licensed Transmitter
BT-GPRS-S
Equipment Class
PCB - PCS Licensed Transmitter