QYXSW45-TBodypack Transmitter

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER AUTHORITY TO OPERATE THE EQUIPMENT. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. RF warning statement: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

SW45-T

FCC ID Label Sample FCC ID: QYXSW45-T This device complies with Part 15 of the FCC Rules.

LABEL LOCATION OF QYXSW45-T

SW45-T

FCCID: QYXSW45-T Report Number: HST201107-2405-FCC Page 1 of 22 Test Report Applicant: Sabine, Inc. Address of Applicant: 13301 Hwy 441, Alachua, FL 32615, USA Equipment Under Test (EUT): EUT Name: Bodypack Transmitter Model No.: SW45-T Trade Mark: N A Serial No.: Not supplied by client Standards: FCC PART15 SUBPART C: 2008 Date of Receipt: Jul. 5, 2011 Date of Test: Jul. 5 to 28, 2011 Date of Issue: Jul. 31, 2011 Test Result : PASS* * In the configuration tested, the EUT complied with the standards specified above. Authorized Signature: Henly Xie / Manager This report refers to the General Conditions for Inspection and Testing Services, printed overleaf This report details the results of the testing carried out on one sample. The results contained in this test report do not relate to other samples of the same product. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. This report may only be reproduced and distributed in full. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. The test report prepare by: Guangzhou Huesent Testing Service Co.,Ltd. Self-ordained 68# courtyard, No.91, Dongguanzhuang Road,Guangzhou,China. Tel: 86-20-28263298 Fax: 86-20-28263237 http://www.hst.org.cn E-mail:[email protected] Report Number: HST201107-2405-FCC Page 2 of 22 1 Test Summary Test Test RequirementTest Method Class / Severity Result Radiated Emission FCC PART 15.249 ANSI C63.4:2003 Class B PASS Occupied Bandwidth FCC PART 15.215 ANSI C63.4:2003 Class B PASS Remark: ♣ Channel Frequency/ MHz Lowest 902.1 Mid 906.0 Highest 927.9 The tests were carried out on the 3 samples with the typical frequency listed above. The lowest and highest frequency were within 0.1MHz margin to “ 902.0MHz to 928MHz ” of the frequency range applied. Fresh battery was used during testing. Report Number: HST201107-2405-FCC Page 3 of 22 2 Contents 1 TEST SUMMARY....................................................................................................................... 2 2 CONTENTS................................................................................................................................3 3 GENERAL INFORMATION........................................................................................................ 4 4.1. CLIENT INFORMATION............................................................................................................. 4 4.2. GENERAL DESCRIPTION OF E.U.T........................................................................................... 4 4.3. DETAILS OF E.U.T.................................................................................................................. 4 4.4. DESCRIPTION OF SUPPORT UNITS........................................................................................... 4 4.5. STANDARDS APPLICABLE FOR TESTING................................................................................... 4 4.6. TEST LOCATION..................................................................................................................... 5 4.7. DEVIATION FROM STANDARDS................................................................................................. 5 4.8. ABNORMALITIES FROM STANDARD CONDITIONS....................................................................... 5 5. EQUIPMENTS USED DURING TEST....................................................................................... 6 6. TEST RESULTS......................................................................................................................... 8 6.1. RADIATION INTERFERENCE ............................................................................................ 8 6.1.1 E.U.T. Operation ............................................................................................................... 8 6.1.2 Test Setup ......................................................................................................................... 8 6.1.3 Test Procedure.................................................................................................................. 8 6.1.4 Measurement Data............................................................................................................ 9 6.2. OCCUPIED BANDWIDTH........................................................................................................ 11 6.2.1 E.U.T. Operation ............................................................................................................. 11 6.2.2 Test Setup ....................................................................................................................... 11 6.2.3 Test Procedure................................................................................................................ 11 6.2.4 Measurement Data..........................................................................................................12 7. PHOTOGRAPHS..................................................................................................................... 14 7.1. RADIATED EMISSION TEST SETUP......................................................................................... 14 7.2. EUT CONSTRUCTIONAL DETAILS.......................................................................................... 15 7.3. ANTENNA PHOTO................................................................................................................. 22 Report Number: HST201107-2405-FCC Page 4 of 22 3 General Information 4.1. Client Information Applicant: Sabine, Inc. Address of Applicant: 1…

Text truncated - open the document above for the full version.

Test Setup of SW45-T