R3AROT118Power meter for bikes

MTB Installation guide | Guía de Instalación ROTOR COMPONENTES TECNOLÓGICOS SL Pol.Ind. Conmar. C/Miño, 14. 28864, Ajalvir, Madrid, Spain P95-013-00310-002 Apr, 2023 3 YEARS 2 Allen 10 mm (Not included) Lea y comprenda en su totalidad el manual de usuario proporcionado por el fabricante Be sure to read and understand the user’s manual provided by manufacturer Die Bedienungsanleitungen der Hersteller für befolgen Assurez-vous de lire et de comprendre le manuel d’utilisation fourni Essere sicuri di avere compreso l manuali d’uso dei produttori [email protected] Allen 5 mm (Not included) Find extra info at: https://rotorbike.com ROTOR ROT118 FCC ID: R3AROT118 IC: 10992A-ROT118 The information in this document is subject to change without notice. 3 SENSOR ID atwww.rotorbike.com/registration Register your ROTOR INpower 4 Warranty Garantía | Garantie | Garanzia • ROTOR INspider power meters are guaranteed for 3 YEARS against any manufacturer defects or defective materials. In the event of a warranty defect, ROTOR’s sole obliga- tion under this warranty is to repair or replace, at its discretion, the defective part or product at no charge. Moreover, in some countries, ROTOR is obliged to ensure any legal warranty defined by law for the customer’s protection. • Elements subject to wear and failures that the manufacturer is not responsible for, are not covered by this warranty. • Failures caused by improper use, poor assembly or inadequate maintenance as declared in the supplied instructions or the user manual are not covered by this warranty. • Always keep your receipt or invoice. • The following acts void this warranty: - Failure to fulfill the requirements above. - Improper use or installation of inadequate parts. Warranty Service: Original purchaser must send their ROTOR product along with the retailer’s original bill, credit card receipt or other satisfactory proof of date of purchase. IP67 Do not disassemble. No desmontar. Nicht demontieren. 5 Product Producto | Produit | Produkt | Prodotto MTB x1 x4 -20 / +60 ºC 0 / 100% HR Environmental operating conditions: 6 Assembly Montaje | Montage | Assemblage | Montaggio 1 7 2 WHY Q? 8 Battery Batería | Batterie | Batterij | Batteria 9 Sensor ID: 12345 2 LED Power 12345 1 3 Pairing Vinculación | Koppeln | Appariement | Accoppiamento 10 Calibration Calibración | Kalibrierung | Calibrage | Calibrazione 11 Declaración de conformidad con la FCC y la Industria de Canadá. Este dispositivo cumple las estipulaciones establecidas por la Industria de Canadá y en la Parte 15 de lanormativa FCC de Estados Unidos. Su funcionamiento quedará sujeto a las dos condiciones siguientes: (1) Este dispositivo no podrá causar interferencias dañinas, y (2) este dispositivo debe aceptar cualquier interferencia recibida, incluidas las interferencias que pueden causar un funcionamiento no deseado. NOTA: tras realizar las pruebas correspondientes, se ha determinado que este equipo cumple los límites establecidos para dispositivos digitales de clase B de conformidad con el apartado 15 de la Normativa FCC. Estos límites se han establecido con el objetivo de aportar una protección razonable contra interferencias perjudiciales cuando el equipo se utiliza en el hogar. Este equipo genera, utiliza y puede emitir energía de radiofrecuencia y, a menos que se instale y se utilice de acuerdo con el manual de instrucciones, puede ocasionar interferencias perjudiciales en las comunicaciones por radio. Sin embargo, no existe garantía de que éstas no se produzcan en determinadas instalaciones. Si el equipo produce interferencias perjudiciales en la recepción de radio o televisión, lo cual puede probarse encendiendo y apagando el equipo, se recomienda al usuario corregir dichas interferencias tomando una o varias de las siguientes medidas: • Modificar la orientación o ubicación de la antena de recepción. • Aumentar la separación entre equipo y receptor. • Conectar el equipo a una toma de corriente o circuito diferente al del receptor. • Consultar al distribuidor o a un técnico especialista de radio o TV. ROTOR no autoriza cambios o modificaciones realizados por el usuario en el dispositivo. Cualquier cambio o modificación podría invalidar el derecho del usuario a utilizar el equipo. Las reparaciones deberán ser realizadas sólo por distribuidores de ROTOR. Cualquier reparación no autorizada puede dañar de forma permanente el equipo y resultar en la suspensión de la garantía. Este dispositivo cumple los límites de exposición a RF de la FCC/ISED y ha sido evaluado conforme a la condición de exposición portátil. Para cumplir con la exclusión de pruebas SAR, el equipo debe instalarse y utilizarse a una distancia mínima de 15 mm del cuerpo humano. Reglamento CEE Este producto cumple con la normativa 93/42/EEC. Por la presente, ROTOR declara que el tipo de equipo radioeléctrico INspider es conforme con la Directiva 2014/53/UE. El texto completo de la declaración UE de conformidad está disponible en la dirección siguiente: http://rotorbike.com/ DECLARACIÓN DE NORMATIVA ROTOR RPM2 FCC ID: R3AROT118 IC: 10992A-ROT118 12 This device complies with part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). This device complies with the FCC/ISED RF exposure limits and has been evaluated in compliance with portable exposure condition. To comply with the SAR testing exclusion, the equipment must be installed and operated with a minimum distance of 15 mm of the human body. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules and with Industry Canada Licen- se-exempt RSS standard(s). These limits are designed to provide reasonable protection against harmful interference in …

Text truncated - open the document above for the full version.

FCB011_02 //DEKRA Testing and Certification, S.A.U. // www.dekra-product-safety.com/wireless Date: 16/10/2023 DEKRA Testing and Certification, S.A.U. Parque Tecnológico de Andalucía C/ Severo Ochoa 2 & 6 29590 Campanillas Málaga, España Certifications concerning “covered” equipment. Section 2.911(d)(5)(i)- (ii) FCC ID: R3AROT118 We, Rotor Componentes Tecnológicos S.L., C/ Miño, 14, 28864 Ajalvir, Madrid, Spain; certify that: - the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. - as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, __________________________ By: David Martínez García Title: Chief Operating Officer Company: Rotor Componentes Tecnológicos S.L. Telephone: +34662116549 e-mail: [email protected]

FCB011_02 //DEKRA Testing and Certification, S.A.U. // www.dekra-product-safety.com/wireless Date: 16/10/2023 DEKRA Testing and Certification, S.A.U. Parque Tecnológico de Andalucía C/ Severo Ochoa 2 & 6 29590 Campanillas Málaga, España Certification designating a U.S. agent for service of process. As required by section 2.911(d)(7), FCC ID: R3AROT118 We, Rotor Componentes Tecnológicos S.L. C/ Miño, 14, 28864 Ajalvir, Madrid, Spain FRN: 0022168058 certify that: ROTOR America, Inc 1420 Edison St., Salt Lake City, UTAH FRN 0034343129 Lori Barrett [email protected] Is our designated U.S. agent for service of process and we acknowledge: - our consent to accept service of process in the United States for matters related to the applicable equipment at the physical U.S. address and email address of the designated U.S. agent - the acceptance to maintain an U.S. agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission- related proceeding involving the equipment. Applicant Designated U.S. Agent Sincerely, ________________ By: David Martínez García Title: Chief Operating Officer Company: Rotor Componentes Tecnológicos S.L. Telephone: +34662116549 e-mail: [email protected] We acknowledge our obligation to accept service of process in the United States for matters related to the applicable equipment at our physical U.S. address and email address stated above. __________________ By: Lori Barrett Title: Managing Director Company: ROTOR America, Inc Telephone: 801 393 4822 e-mail: [email protected]

FCB011_02 //DEKRA Testing and Certification, S.A.U. // www.dekra-product-safety.com/wireless Date: 16/10/2023 DEKRA Testing and Certification, S.A.U. Parque Tecnológico de Andalucía C/ Severo Ochoa 2 & 6 29590 Campanillas Málaga, España Ref: Agent letter for FCC ID: R3AROT118 We, Rotor Componentes Tecnológicos S.L. C/ Miño, 14, 28864 Ajalvir, Madrid (Spain), hereby authorize DEKRA Testing and Certification S.A.U., Parque Tecnológico de Andalucía C/ Severo Ochoa 2 & 6 29590 Campanillas, Málaga, España Ms. Inmaculada Quesada Rodríguez, e-mail: [email protected], Phone: +34 952 619 146 to act as our agent in the preparation of this application for equipment certification, including the signing of all documents relating to these matters. The present authorization considers the development of documents on behalf of the client, written under his own letterhead and related to the necessary information to be provided on his behalf to complete the certification process. We also hereby certify that neither we nor any party to this application are subject to a denial of U.S. Federal benefits, which include FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, U.S.C. 862 because of conviction for possession or distribution of controlled substance. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by DEKRA Testing and Certification, S.A.U., still resides with us. This agreement expires one year from the current date. Sincerely, __________________________ By: David Martínez García Title: Chief Operating Officer Company: Rotor Componentes Tecnológicos S.L. Telephone: +34662116549 e-mail: [email protected]

FCB011_02 //DEKRA Testing and Certification, S.A.U. // www.dekra-product-safety.com/wireless Date: 16/10/2023 DEKRA Testing and Certification, S.A.U. Parque Tecnológico de Andalucía C/ Severo Ochoa 2 & 6 29590 Campanillas Málaga, España Ref: Confidentiality request for FCC ID: R3AROT118 To whom it may concern: Pursuant to §0.457(d)(1)(ii) and §0.459 of the Commission’s Rules (47 C.F.R.) and §552 (b)(4) of the Freedom of Information Act, Rotor Componentes Tecnológicos S.L. hereby requests that a part of the subject FCC application be held confidential to avoid release of sensitive information of the product to the public. For the product stated above, we request that the following information be withheld from public disclose: Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagrams Short Term External Photos Short Term Internal Photos Short Term Permanent Operation Description Short Term Permanent Parts List & Placement/BOM Short Term Permanent Tune-Up Procedure Short Term Permanent Schematics Short Term Test Setup Photos Short Term User’s Manual Short Term Permanent SDR software and security information Permanent Confidentiality: The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to us and provide unjustified benefits to our competitors. Short-Term Confidentiality: We hereby request short-term confidentiality for the product stated above to avoid premature release of sensitive information prior to marketing or release of the product to the public. Release date of short term confidentiality is: 45 days from grant date marked 90 days from grant date marked 135 days from grant date marked 180 days from grant date marked Specific date: We are also aware that we are responsible to notify DEKRA in the event information regarding the product or the product is made available to the public. DEKRA will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. FCB011_02 //DEKRA Testing and Certification, S.A.U. // www.dekra-product-safety.com/wireless Sincerely, __________________________ By: David Martínez García Title: Chief Operating Officer Company: Rotor Componentes Tecnológicos S.L. Telephone: +34662116549 e-mail: [email protected]

FCB011_02 //DEKRA Testing and Certification, S.A.U. // www.dekra-product-safety.com/wireless Date: 16/10/2023 DEKRA Testing and Certification, S.A.U. Parque Tecnológico de Andalucía C/ Severo Ochoa 2 & 6 29590 Campanillas Málaga, España Ref: sDoC declaration letter for equipment with FCC ID: R3AROT118 Pursuant to §15.101 of the Commission’s Rules (47 C.F.R.), Rotor Componentes Tecnológicos S.L. hereby declare that the device above mentioned is classified under the following equipment class/classes: JAB Part 15 Class B Digital Device JAD Part 15 Class A Digital Device JAV Other Non-Digital SDoC Devices JBP Part 15 Class B Computing Device/Personal Computer JBC Part 15 Class B Computing Device/Personal Computer CXX Communications Rcvr for use w/ licensed Tx and CBs CRR Superregenerative Receiver CYY Communications Receiver used w/Pt 15 Transmitter HID Part 15 TV Interface Device And will follow the Authorization procedure Supplier’s Declaration of Conformity prior to the initiation of marketing. Sincerely, __________________________ By: David Martínez García Title: Chief Operating Officer Company: Rotor Componentes Tecnológicos S.L. Telephone: +34662116549 e-mail: [email protected]

DEKRA Testing and Certification, S.A.U. Parque Tecnológico de Andalucía, c/ Severo Ochoa nº 2 · 29590 Campanillas · Málaga · España C.I.F. A29 507 456 Report No: (NIE) 74540RAN.001 2023-05-04 Test report No: NIE: 74540RAN.001 Assessment report RF EXPOSURE REPORT ACCORDING TO FCC 47 CFR Part 2.1093 FCC 47 CFR Part 1.1307 (*) Identification of item under evaluation Powermeter for bikes (*) Trademark ROTOR INspider MTB (*) Model and /or type reference ROT118 (*) Other identification of the product HW version: Rev C SW Version: 1.004 FCC ID: R3AROT118 IC: 10992A-ROT118 (*) Features ANT+ and Bluetooth Smart (*) Manufacturer Rotor Componentes Tecnológicos S.L. C/ Miño, 14 28864 Ajalvir, Madrid, SPAIN Test method requested, standard FCC 47 CFR Part 2.1093. Radiofrequency radiation exposure evaluation: portable devices. FCC 47 CFR Part 1.1307: Actions that may have a significant environmental effect, for which Environmental Assessments (EAs) must be prepared. Summary IN COMPLIANCE Approved by (name / position & signature) Miguel Lacave Antennas Lab Manager Date of issue 2023-05-04 Report template No FAN24_02 (*) “Data provided by the client” DEKRA Testing and Certification, S.A.U. Parque Tecnológico de Andalucía, c/ Severo Ochoa nº 2 · 29590 Campanillas · Málaga · España C.I.F. A29 507 456 Report No: (NIE) 74540RAN.001 Page 2 of 8 2023-05-04 Index Competences and guarantees .................................................................................................... 3 General conditions ...................................................................................................................... 3 Data provided by the client .......................................................................................................... 3 Identification of the client............................................................................................................. 3 Document history ........................................................................................................................ 3 Appendix A: FCC RF Exposure assessment result ..................................................................... 4 General description of the device under evaluation ................................................................ 5 Evaluation Results .................................................................................................................. 5 Appendix B: FCC RF Exposure information ................................................................................ 6 RF Exposure determination of exemption ............................................................................... 7 DEKRA Testing and Certification, S.A.U. Parque Tecnológico de Andalucía, c/ Severo Ochoa nº 2 · 29590 Campanillas · Málaga · España C.I.F. A29 507 456 Report No: (NIE) 74540RAN.001 Page 3 of 8 2023-05-04 Competences and guarantees In order to assure the traceability to other national and international laboratories, DEKRA Testing and Certification, S.A.U. has a calibration and maintenance program for its measurement equipment. DEKRA Testing and Certification, S.A.U. guarantees the reliability of the data presented in this report, which is the result of the measurements and the tests performed to the item under test on the date and under the conditions stated on the report and, it is based on the knowledge and technical facilities available at DEKRA Testing and Certification, S.A.U. at the time of performance of the test. DEKRA Testing and Certification, S.A.U. is liable to the client for the maintenance of the confidentiality of all information related to the item under test and the results of the test. The results presented in this Assessment Report apply only to the particular item under test established in this document. IMPORTANT: No parts of this report may be reproduced or quoted out of context, in any form or by any means, except in full, without the previous written permission of DEKRA Testing and Certification, S.A.U. General conditions 1. This report is only referred to the item that has undergone the assessment. 2. This report does not constitute or imply on its own an approval of the product by the Certification Bodies or competent Authorities. 3. This document is only valid if complete; no partial reproduction can be made without previous written permission of DEKRA Testing and Certification, S.A.U. 4. This test report cannot be used partially or in full for publicity and/or promotional purposes without previous written permission of DEKRA Testing and Certification, S.A.U. and the Accreditation Bodies Data provided by the client The following data has been provided by the client: 1. Information relating to the description of the sample ("Identification of the item under evaluation", "Trademark", "Model and/or type reference", “Other identification of the product”, “Features”, “Manufacturer” and “General description of the device”). 2. Maximum output power, maximum antenna gain and use distance information. DEKRA Testing and Certification, S.A.U. declines any responsibility with respect to the information provided by the client and that may affect the validity of results. Identification of the client Company name: Rotor Componentes Tecnológicos S.L. Postal address: C/ Miño, 14, 28864 Ajalvir, Madrid Contact person: Ingeniero Electrónico Telephone / e-mail: 659775357 / [email protected] Document history Report number Date Description 74540RAN.001 2023-05-04 First release DEKRA Testing and Certification, S.A.U. Parque Tecnológico de Andalucía, c/ Severo Ochoa nº 2 · 29590 Campanillas · Málaga · España C.I.F. A29 507 456 Report No: (NIE) 74540RAN.001 Page 4 of 8 2023-05-04 Appendix A: FCC RF Exposure assessment result DEKRA Testing and Certification, S.A.U. Parque Tecnológico de Andalucía, c/ Severo Ochoa nº 2 · 29590 Campanillas · Málaga · España C.I.F. A29 507 456 Report No: (NIE) 74540RAN.001 Page 5 of 8 2023-05-04 General description of the device under evalua…

Text truncated - open the document above for the full version.

APPLICATION SPECIFICATION REVISION: ECR/ECN INFORMATION: TITLE: 2.4GHz MID SMT Antenna Application Specification SHEET No. F EC No: 637286 1 of 16 DATE: 2020/05/11 DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY: AS-479480001 Liu Hai 2020/05/11 Cheng Kang 2020/05/11 Andy Zhang 2020/05/11 TEMPLATE FILENAME: APPLICATION_SPEC[SIZE_A](V.1).DOC TITLE 2.4GHZ MID SMT ANTENNA TABLE OF CONTENTS 1.0 SCOPE 2.0 PRODUCT DESCRIPTION 3.0 APPLICABLE DOCUMENTS 4.0 ANTENNA PERFORMANCE 5.0 RECOMMENDED REFLOW CONDITION 6.0 MATCHING NETWORK DESRICPTION 7.0 RF PERFORMANCE AS A FUNCTION OF IMPLEMENTATION APPLICATION SPECIFICATION REVISION: ECR/ECN INFORMATION: TITLE: 2.4GHz MID SMT Antenna Application Specification SHEET No. F EC No: 637286 2 of 16 DATE: 2020/05/11 DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY: AS-479480001 Liu Hai 2020/05/11 Cheng Kang 2020/05/11 Andy Zhang 2020/05/11 TEMPLATE FILENAME: APPLICATION_SPEC[SIZE_A](V.1).DOC 2.4GHZ MID SMT ANTENNA 1.0 SCOPE This specification describes the antenna application and recommended PCB layout for the Molex 2.4GHz SMD Antenna. The information in this document is for reference and benchmark purposes only. The user is responsible for validating antenna RF performance based on users own PCB and matching circuits. All measurements are done of the antenna mounted on the recommended PCB with VNA Agilent 5071C and OTA chamber. Antenna illustrations in this document are generic representations. They are not intended to be an image of any antenna listed in the scope. 2.0 PRODUCT DESCRIPTION 2.1 PRODUCT NAME AND SERIES NUMBER (S) Product name: 2.4GHz MID SMT Antenna Series Number: 479480001 2.2 DESCRIPTION This is a high-performance antenna implemented using SMD option to meet the customer needs. It has low profile as the size of this antenna. It is designed to cover the frequency 2.4GHz-2.5GHz. 2.3 PRODUCT STRUCTURE INFORMATION Please refer to PS-479480001 for full information. FIGURE 2.3 DIMENSION OF THE 2.4GHZ SMD ANTENNA APPLICATION SPECIFICATION REVISION: ECR/ECN INFORMATION: TITLE: 2.4GHz MID SMT Antenna Application Specification SHEET No. F EC No: 637286 3 of 16 DATE: 2020/05/11 DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY: AS-479480001 Liu Hai 2020/05/11 Cheng Kang 2020/05/11 Andy Zhang 2020/05/11 TEMPLATE FILENAME: APPLICATION_SPEC[SIZE_A](V.1).DOC 3.0 APPLICABLE DOCUMENTS DOCUMENT NUMBER DESCRIPTION Sale Drawing (SD) SD-479480001 Mechanical Dimension of the product Product Specification (PS) PS-479480001 Product Specification Packing Drawing (PK) PK-479480001 Product packaging specifications 4.0 ANTENNA PERFORMANCE 4.1 RF TEST CONDITIONS The reference design is based on a recommended double side PCB size of 100 mm*40 mm*0.8 mm. There are one feeding pad and three fixing pads.(PCB molex p/n:479489001) FIGURE4.1.1 REFERENCE ANTENNA LOCATION APPLICATION SPECIFICATION REVISION: ECR/ECN INFORMATION: TITLE: 2.4GHz MID SMT Antenna Application Specification SHEET No. F EC No: 637286 4 of 16 DATE: 2020/05/11 DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY: AS-479480001 Liu Hai 2020/05/11 Cheng Kang 2020/05/11 Andy Zhang 2020/05/11 TEMPLATE FILENAME: APPLICATION_SPEC[SIZE_A](V.1).DOC FIGURE4.1.2 ANTENNA IN FREE SPACE WITH VNA AGILENT E5071C FIGURE4.1.3 ANTENNA IN FREE SPACE WITH OTA CHAMBER DUT DUT APPLICATION SPECIFICATION REVISION: ECR/ECN INFORMATION: TITLE: 2.4GHz MID SMT Antenna Application Specification SHEET No. F EC No: 637286 5 of 16 DATE: 2020/05/11 DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY: AS-479480001 Liu Hai 2020/05/11 Cheng Kang 2020/05/11 Andy Zhang 2020/05/11 TEMPLATE FILENAME: APPLICATION_SPEC[SIZE_A](V.1).DOC 4.2 ANTENNA PERFORMANCE DESCRIPTION EQUIPMENT REQUIREMENT Frequency Range VNA E5071C 2.4~2.5GHz Return Loss VNA E5071C < -6 dB Peak Gain (Max) OTA Chamber 3.7dBi Average Total Efficiency OTA Chamber >70% Polarization OTA Chamber Linear Input Impedance VNA E5071C 50 Ohms Note that the above antenna performance is measured with just the antenna mounted on a recommended PCB to similar a free-space condition. When implement into the system, the frequency resonant might be off-tune due to the loading of surrounding components especially metal plane. This off-tune can be compensated through matching. Although module manufacturers specify a peak gain limit, it is based on free-space conditions. The peak gain will be degraded by 1 to 2dBi in the actual implementation as the radiation pattern will change due to the surround components. As such, during selection of antenna, you can select one with high peak gain to compensate for the loss. Molex can offer assistant to choose the best location and best tuning in-order to meet this peak gain requirement. APPLICATION SPECIFICATION REVISION: ECR/ECN INFORMATION: TITLE: 2.4GHz MID SMT Antenna Application Specification SHEET No. F EC No: 637286 6 of 16 DATE: 2020/05/11 DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY: AS-479480001 Liu Hai 2020/05/11 Cheng Kang 2020/05/11 Andy Zhang 2020/05/11 TEMPLATE FILENAME: APPLICATION_SPEC[SIZE_A](V.1).DOC 4.3 RETURN LOSS PLOT All measurements in this document are done of the antenna mounted on the recommended PCB. FIGURE 4.3 RETURN LOSS OF ANTENNA IN FREE SPACE 4.4 EFFICIENCY PLOT All measurements in this document are done of the antenna mounted on the recommended PCB. FIGURE 4.4 EFFICIENCY OF ANTENNA IN FREE SPACE APPLICATION SPECIFICATION REVISION: ECR/ECN INFORMATION: TITLE: 2.4GHz MID SMT Antenna Application Specification SHEET No. F EC No: 637286 7 of 16 DATE: 2020/05/11 DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY: AS-479480001 Liu Hai 2020/05/11 Cheng Kang 2020/05/11 Andy Zhang 2020/05/11 TEMPLATE FILENAME: APPLICATION_SPEC[SIZE_A](V.1).DOC 4.5 RADIATION PATTERN All measurements in this document are done of the antenna mounted on the recommended PCB. FIGURE 4.5.1 2D RADIATION PATTERN OF ANTENNA AT 2.45GHZ IN FREE SPACE APPLICATION SPECIFICATION …

Text truncated - open the document above for the full version.

DEKRA Testing and Certification, S.A.U. Parque Tecnológico de Andalucía, c/ Severo Ochoa nº 2 · 29590 Campanillas · Málaga · España C.I.F. A29507456 Report No: NIE:74540RRF.001 2023-02-24 ISED CABid: ES1909 Lab. Company Number: 4621A Test Report No: NIE: 74540RRF.001 Test Report USA FCC Part 15.247, 15.209 CANADA RSS-247, RSS-Gen (*) Identification of item tested Powermeter for bikes (*) Trademark ROTOR INspiderMTB (*) Model and /or type reference ROT118 Other identification of the product FCC ID: R3AROT118 IC: 10992A-ROT118 (*) Features Features: ANT+ and Bluetooth Smart HW version: Rev C SW version: 1.004 Applicant Rotor Componentes Tecnológicos S.L. C/ Miño, 14 28864 Ajalvir, Madrid, SPAIN Test method requested, standard USA FCC Part 15.247 (10-1-21 Edition): Operation within the bands 902 - 928 MHz, 2400 -2483.5 MHz, and 5725 - 5850 MHz. USA FCC Part 15.209 (10-1-21 Edition): Radiated emission limits; general requirements. CANADA RSS-247 Issue 2 (February 2017). CANADA RSS-Gen Issue 5 amendment 1 (March 2019). Guidance for Performing Compliance Measurements on Digital Transmission System, Frequency Hopping Spread Spectrum System, and Hybrid Systems Devices Operating Under Section 15.247 of the FCC Rules. 558074 D01 Meas Guidance v05r02 dated April 2, 2019. ANSI C63.10-2013: American National Standard for Testing Unlicensed Wireless Devices. Summary IN COMPLIANCE Approved by (name / position & signature) José Manuel Gómez Galván EMC Consumer & RF Lab. Manager Date of issue 2023-02-24 Report template No FDT08_24 (*) “Data provided by the client” DEKRA Testing and Certification, S.A.U. Parque Tecnológico de Andalucía, c/ Severo Ochoa nº 2 · 29590 Campanillas · Málaga · España C.I.F. A29507456 Report No: NIE: 74540RRF.001 Page 2 of 73 2023-02-24 Index INDEX ........................................................................................................................................................................... 2 ACRONYMS ................................................................................................................................................................. 3 COMPETENCES AND GUARANTEES ....................................................................................................................... 3 GENERAL CONDITIONS ............................................................................................................................................. 4 UNCERTAINTY ............................................................................................................................................................ 4 DATA PROVIDED BY THE CLIENT ............................................................................................................................ 4 USAGE OF SAMPLES ................................................................................................................................................. 5 TEST SAMPLE DESCRIPTION ................................................................................................................................... 6 IDENTIFICATION OF THE CLIENT ............................................................................................................................. 7 TESTING PERIOD AND PLACE .................................................................................................................................. 7 DOCUMENT HISTORY ................................................................................................................................................ 7 ENVIRONMENTAL CONDITIONS ............................................................................................................................... 7 REMARKS AND COMMENTS ..................................................................................................................................... 8 TESTING VERDICTS ................................................................................................................................................... 9 SUMMARY ...................…

Text truncated - open the document above for the full version.