R48CONTROL24GRXRWireless Speaker System-Receiver

® CONTROL ® 2.4G JBL ® ON AIR OWNER’S GUIDE English 4 IMPORTANT SAFETY INSTRUCTIONSPlease read the following precautions before use:1. Read these instructions.2. Keep these instructions.3. Heed all warnings.4. Follow all instructions.5. Do not use this apparatus near water.6. Clean only with a dry cloth.7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.8. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat.9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.10. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles and the point where they exit from the apparatus.11. Only use attachments/accessories specified by the manufacturer.12. Use only with the cart, stand, tripod, bracket or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.13. Unplug this apparatus during lightning storms or when unused for long periods of time.14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.15. Do not expose this apparatus to dripping or splashing and ensure that no objects filled with liquids, such as vases, are placed on the apparatus.16. To completely disconnect this apparatus from the AC Mains, disconnect the power supply cord plug from the AC receptacle.17. The mains plug of the power supply cord shall remain readily operable.18. Do not expose batteries to excessive heat such as sunshine, fire or the like. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENTThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: s2EORIENTORRELOCATETHERECEIVINGANTENNAs)NCREASETHESEPARATIONBETWEENTHEEQUIPMENTANDRECEIVERs#ONNECTTHEEQUIPMENTINTOANOUTLETONACIRCUITDIFFERENT FROMTHAT to which the receiver is connected. s#ONSULTTHEDEALERORANEXPERIENCEDRADIO46TECHNICIANFOR HELP FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. FCC Radiation Exposure StatementThis equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. IC Statement and WarningThis Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du CanadaIC Statement and Warning. 5 THANK YOU FOR CHOOSING JBLFor more than 60 years, JBL has been involved in every aspect of music and film recording and reproduction, from live performances to the recordings you play in your home, car or office.We’re confident that the JBL system you have chosen will provide every note of enjoyment that you expected – and that when you think about purchasing additional audio equipment for your home, car or office, you will once again choose JBL.Please take a moment to register your product on our Web site at www.jbl.com. It enables us to keep you posted on our latest advance-ments, and helps us to better understand our customers and build products that meet their needs and expectations.The JBL ® On Air Control ® 2.4G is an advanced wireless loudspeaker system that allows you to enjoy your favorite music in remote locations around your home, or to add surround speakers to your home theater system without running wires to the back of the room. To ensure trouble-free performance, please carefully read these instructions completely before connecting or using the system. UNPACKING THE SYSTEMCarefully unpack the sy…

Text truncated - open the document above for the full version.

Report No.: 13A0199R-RFUSP42V01 Page : 1 of 5 Attachment 2 : EUT Detailed Photographs (1) EUT Photo (2) EUT Photo Report No.: 13A0199R-RFUSP42V01 Page : 2 of 5 (3) EUT Photo (Left channel speaker) (4) EUT Photo (Left channel speaker) Report No.: 13A0199R-RFUSP42V01 Page : 3 of 5 (5) EUT Photo (Left channel speaker) (6) EUT Photo (Left channel speaker) Report No.: 13A0199R-RFUSP42V01 Page : 4 of 5 (7) EUT Photo (Right channel speaker) (8) EUT Photo (Right channel speaker) Report No.: 13A0199R-RFUSP42V01 Page : 5 of 5 (9) EUT Photo (Right channel speaker)

Meiloon Industrial Co., Ltd. FCC ID.: R48CONTROL24GRXR No.77, Lane 1775, Chuen-Ryh Road, Taoyuan City, TaiwanTel : 886-33261611 The FCC ID will be placed on the equipment as shown in the photograph below.

Report No.: 13A0199R-RFUSP42V01 Page : 1 of 12 Attachment 2 : EUT Detailed Photographs (1) EUT Photo (2) EUT Photo Right channel speaker Right channel speaker Without Module Report No.: 13A0199R-RFUSP42V01 Page : 2 of 12 (3) EUT Photo (4) EUT Photo Left channel speaker Left channel speaker Main Board & Module Report No.: 13A0199R-RFUSP42V01 Page : 3 of 12 (5) EUT Photo (6) EUT Photo Antenna Report No.: 13A0199R-RFUSP42V01 Page : 4 of 12 (7) EUT Photo (8) EUT Photo Report No.: 13A0199R-RFUSP42V01 Page : 5 of 12 (9) EUT Photo-Module (10) EUT Photo Report No.: 13A0199R-RFUSP42V01 Page : 6 of 12 (11) EUT Photo-Antenna (12) EUT Photo Report No.: 13A0199R-RFUSP42V01 Page : 7 of 12 (13) EUT Photo (14) EUT Photo Report No.: 13A0199R-RFUSP42V01 Page : 8 of 12 (15) EUT Photo (16) EUT Photo Report No.: 13A0199R-RFUSP42V01 Page : 9 of 12 (17) EUT Photo (18) EUT Photo Report No.: 13A0199R-RFUSP42V01 Page : 10 of 12 (19) EUT Photo (20) EUT Photo Report No.: 13A0199R-RFUSP42V01 Page : 11 of 12 (21) EUT Photo (Audio Cable) (22) EUT Photo (Audio to RCA Cable) Report No.: 13A0199R-RFUSP42V01 Page : 12 of 12 (23) EUT Photo (24) EUT Photo

Report No.: 13A0199R-RFUSP42V01 Page: 1 of 3 RF Exposure Evaluation declaration Product Name Wireless Speaker System-Reciever Model No. CONTROL 2.4G FCC ID R48CONTROL24GRXR Applicant Meiloon Industrial Co., Ltd. Address No.77, Lane 1775, Chuen-Ryh Road, Taoyuan City, Taiwan Date of Receipt Oct. 09, 2013 Date of DeclarationNov. 07, 2013 Report No. 13A0199R-RFUSP42V01 The test results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. This report must not be used to claim product endorsement by TAF or any agency of the U.S. Government Report No.: 13A0199R-RFUSP42V01 Page: 2 of 3 1. RF Exposure Evaluation 1.1. Limits According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in 1.1307(b) LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (Minutes) (A) Limits for Occupational/ Control Exposures 300-1500 -- -- F/300 6 1500-100,000 -- -- 5 6 (B) Limits for General Population/ Uncontrolled Exposures 300-1500 -- -- F/1500 6 1500-100,000 -- -- 1 30 F= Frequency in MHz Friis Formula Friis transmission formula: Pd = (Pout*G)/(4*pi*r 2 ) Where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm Pd id the limit of MPE, 1 mW/cm 2 . If we know the maximum gain of the antenna and the total power input to the antenna, through the calculation, we will know the distance r where the MPE limit is reached. 1.2. Test Procedure Software provided by client enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. The temperature and related humidity: 18°Cand 78％ RH. Report No.: 13A0199R-RFUSP42V01 Page: 3 of 3 1.3. Test Result of RF Exposure Evaluation Product : Wireless Speaker System-Reciever Test Item : RF Exposure Evaluation Test Site : No.3 OATS Output Power Into Antenna & RF Exposure Evaluation Distance (1.53dBi): Output Power to Antenna (mW) Power Density at R = 20 cm (mW/cm2) 3.3497 0.000948 Power density in column 4 is much lower than the limit (1 mW/cm 2 ).

Report No.: 13A0199R-RFUSP42V01 Page : 1 of 44 FCC Test Report Product Name Wireless Speaker System-Reciever Model No CONTROL 2.4G FCC ID. R48CONTROL24GRXR Applicant Meiloon Industrial Co., Ltd. Address No.77, Lane 1775, Chuen-Ryh Road, Taoyuan City, Taiwan Date of Receipt Oct. 09, 2013 Issue Date Nov. 11, 2013 Report No. 13A0199R-RFUSP42V01 Report Version V1.0 The test results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. This report must not be used to claim product endorsement by TAF or any agency of the U.S. Government Report No.: 13A0199R-RFUSP42V01 Page : 2 of 44 Test Report Certification Issue Date: Nov. 11, 2013 Report No.: 13A0199R-RFUSP42V01 Product Name Wireless Speaker System-Reciever Applicant Meiloon Industrial Co., Ltd. Address No.77, Lane 1775, Chuen-Ryh Road, Taoyuan City, Taiwan Manufacturer Harman International Industries, Incorporated Model No. CONTROL 2.4G EUT Rated Voltage AC 100-240V, 50/60Hz EUT Test Voltage AC 120V/ 60Hz Trade Name JBL Applicable Standard FCC CFR Title 47 Part 15 Subpart C: 2012 ANSI C63.4: 2003, ANSI C63.10: 2009, KDB 558074 Test Result Complied The test results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. This report must not be used to claim product endorsement by TAF or any agency of the U.S. Government Documented By : ( Senior Adm. Specialist / Rita Huang ) Tested By : ( Engineer / Nowal Kuo ) Approved By : ( Manager / Vincent Lin) Report No.: 13A0199R-RFUSP42V01 Page : 3 of 44 TABLE OF CONTENTS Description Page 1. GENERAL INFORMATION .....................................................................................................5 1.1. EUT Description............................................................................................................................5 1.2. Operational Description ................................................................................................................7 1.3. Tested System Details....................................................................................................................8 1.4. Configuration of Tested System ....................................................................................................8 1.5. EUT Exercise Software .................................................................................................................8 1.6. Test Facility ...................................................................................................................................9 2. Conducted Emission..................................................................................................................10 2.1. Test Equipment............................................................................................................................10 2.2. Test Setup ....................................................................................................................................10 2.3. Limits ..........................................................................................................................................11 2.4. Test Procedure .............................................................................................................................11 2.5. Uncertainty ..................................................................................................................................11 2.6. Test Result of Conducted Emission.............................................................................................12 3. Peak Power Output ...................................................................................................................14 3.1. Test Equipment............................................................................................................................14 3.2. Test Setup ....................................................................................................................................14 3.3. Limits ..........................................................................................................................................14 3.4. Test Procedure .............................................................................................................................14 3.5. Uncertainty ..................................................................................................................................14 3.6. Test Result of Peak Power Output...............................................................................................15 4. Radiated Emission .....................................................................................................................16 4.1. Test Equipment............................................................................................................................16 4.2. Test Setup ....................................................................................................................................17 4.3. Limits ..........................................................................................................................................18 4.4. Test Procedure .............................................................................................................................18 4.5. Uncertainty ..................................................................................................................................18 4.6. Test Result of Radiated Emission................................................................................................19 5. RF antenna conducted test........................................................................................................23 5.1. Test Equipment..............................................................................................................…

Text truncated - open the document above for the full version.

Report No.: 13A0199R-RFUSP42V01 Page : 1 of 3 Attachment 1: EUT Test Setup Photographs Front View of Conducted Test Back View of Conducted Test Report No.: 13A0199R-RFUSP42V01 Page : 2 of 3 Front View of Radiated Test Back View of Radiated Test Report No.: 13A0199R-RFUSP42V01 Page : 3 of 3 Front View of Radiated Test (Horn) Back View of Radiated Test (Horn)