R7PNG0R1X8Electricity Meter Module

© Landis+Gyr 2022 | Proprietary + Confidential Series 6 MCM0 Data Sheet Publication: 98-2947 Rev AA Draft 07.11.2022 A Limitation on Warranties and Liability Information in this document is subject to change without notice. This manual or any part of it thereof may not be reproduced in any form unless permitted by contract or by written permission of Landis+Gyr. In no event will Landis+Gyr be liable for any incidental, indirect, special, or consequential damages (including lost profits) arising out of or relating to this publication or the information contained in it, even if Landis+Gyr has been advised, knew, or should have known of the possibility of such damages. Covered by both issued and pending patents. For further patent information see: https://www.landisgyr.com/about/patent-notices/ © 2022 Landis+Gyr, Inc. | Proprietary + Confidential Contact Us: To provide feedback about this document, email us at [email protected] Customer Support: 1-888-390-5733 | [email protected] 98-2947 Rev AA | Series 6 MCM0 Data Sheet | Release Date Pending Draft 07.11.2022 A Data Sheet98-2947 Rev AA | 3 Series 6 MCM0 Data Sheet Introduction Landis+Gyr's Series 6 MCM0 is key to building a single, integrated IoT network for your utility future. This product is a fully functional Network Interface Card (NIC) in a multi-chip module form-factor to enable low-cost network and sensor device integration. This technology is foundational to Landis+Gyr's industry-leading utility IoT networking solution, Gridstream® Connect. Furthermore, the Series 6 MCM0 provides the flexibility to grow the value of your IoT platform over time with proven Wi-SUN FAN interoperability as you integrate todays and future AMI or DA networking equipment and third-party IoT devices. The device supports RF Mesh IP and Wi-SUN FW stacks. Figure 1. Series 6 MCM0 Table - 1. Technical Specifications ElementDescription Radio ModelS6-MCM0 Communication Protocol (PHY) IEEE 802.15.4-2015 MAC/PHY Features MAC Automatic selection of ‘best’ Band based on Link Quality Automatic selection of ‘best’ Modulation based on Link Quality PHY Adaptive Power Control Precision Output Power Management Clear Channel Assessment Hardware Capabilities Clock Speed120 MHz RAM Memory640 Kbytes FLASH Memory2 MB + 4 MB External RF ModulationIEEE 802.15.4 SUN FSK, O-QPSK & OFDM RF Bands902 – 928 MHz Draft 07.11.2022 A 4 | 98-2947 Rev AAData Sheet Series 6 MCM0 Data Sheet RF Ports1 Table - 2.Sub-GHz Band Characteristics: North America Network Operating Mode RF Mesh IP Series 5 Compatible RF Mesh IP Green Field Wi-SUN Frequency Range (Fc) 902.4 MHz - 927.6 MHz 904 MHz - 926.8 MHz 902.2 MHz – 927.8 MHz Channel Width400 KHz1200 kHz200, 400, 800 & 1200 kHz Number of Channels 6420129, 64 31 & 21 Multicast Modulation 2-FSK 50 kbps OFDM Option 1 MCS0 (100 kbps) 2-FSK 50 kbps Unicast Modulation Support 2-FSK: 50 - 200 kbps OFDM Option 3: MCS3 - MCS6 OFDM Option 1: MCS0 - MCS6 2-FSK: 50 - 200 kbps OFDM Option 3: MCS2 - MCS3 (100 - 200 kbps) OFDM Option 2: MCS3 - MCS5 (400 - 800 kbps) OFDM Option 1: MCS5 - MCS6 (1600 - 2400 kbps) Data Rate Coverage50 kbps - 600 kbps100 kbps - 2400 kbps 50 kbps - 2400 kbps Transmitter Output Power 10 mW - 500 mW10 mW - 316 mW10 mW - 500 mW (peak) Receiver Sensitivity (IEEE 802.15.4) F2B50 = -108 dBm F2B150 = -100 dBm F2B200 = -99 dBm O3M3 = -107 dBm O3M4 = -105 dBm O3M5 = -102 dBm O3M6 = -97 dBm O1M0 = -110 dBm O1M1 = -109 dBm O1M2 = -105 dBm O1M3 = -102 dBm O1M4 = -99 dBm O1M5 = -96 dBm O1M6 = -90 dBm F2B50 = -108 dBm F2B150 = -100 dBm F2B200 = -99 dBm O3M2 = -109 dBm O3M3 = -107 dBm O2M3 = -106 dBm O2M4 = -104 dBm O2M5 = -101 dBm O1M5 = -96 dBm O1M6 = -90 dBm Table - 1. Technical Specifications (Continued) ElementDescription Draft 07.11.2022 A Data Sheet98-2947 Rev AA | 5 Series 6 MCM0 Data Sheet Series 6 MCM0 Outline The PCB outline is shown below: Figure 2. PCB Outline 1 Figure 3. PCB Outline 2 FCC and Industry Canada Compliance FCC Class B This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: •This device may not cause harmful interference, and •This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed Draft 07.11.2022 A 6 | 98-2947 Rev AAData Sheet Series 6 MCM0 Data Sheet and used in accordance with the Instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •Reorient or relocate the receiving antenna. •Increase the separation between the equipment and receiver. •Consult Landis+Gyr or an experienced radio technician for help. WARNING: Changes or modifications to this device not expressly approved by Landis+Gyr could void the user’s authority to operate the equipment. RF Exposure This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. Cet équipement est conforme aux limites FCC/ISED d'exposition aux radiations définies pour un environnement non contrôlé. Cet équipement doit être installé et utili…

Text truncated - open the document above for the full version.

30000 Mill Creek Avenue, Suite 100 | Alpharetta, GA 30022 Tel: +1 678 258 1637 | Fax: +1 678 258 1681 CONFIDENTIALITY REQUEST Date: May 18, 2022 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Gentlemen: Landis+Gyr Technology, Inc. respectfully requests confidentiality of certain materials provided with the submission of the Series 6 MCM0 under FCC ID: R7PNG0R1X8 in accordance with FCC Regulations 0.459. The confidentiality request applies to the System Block Diagram, Schematics, Parts List, and Theory of Operation contained in this filing. Series 6 MCM0 has been developed at considerable effort and expense by Landis+Gyr Technology, Inc. These items are considered as Trade Secrets and therefore public access to the proprietary material could possibly result in duplication of equipment that could severely damage the company's business advantage. I appreciate your assistance in this matter. Sincerely, James L. Stortz Title: Head of Communication Hardware Delivery

30000 Mill Creek Avenue, Suite 100 | Alpharetta, GA 30022 Tel: +1 678 258 1637 | Fax: +1 678 258 1681 May 18, 2022 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Rd. Columbia, MD 21046 Dear Sir or Madam: I hereby appoint Kirby Munroe at TÜV SÜD America to act as our agent in the preparation of an application for equipment authorization of FCC ID: R7PNG0R1X8 to the FCC Rules and Regulations. I certify that all exhibits contained within this filing properly describe the device or system for which authorization is sought. I further certify that appropriate arrangements have been made to assure that production units of this equipment bearing the name and FCC IDENTIFIER listed in this application will continue to comply with the Commission's requirements. I further certify by signature below that no party (per 47 CFR 1.2002(b)) to the application is subject to a denial of Federal benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). This appointment also includes the authority to complete FCC Form 731 on our behalf and sign the application as an authorized agent. Sincerely, James L. Stortz Title: Head of Communication Hardware Delivery

30000 Mill Creek Avenue, Suite 100 | Alpharetta, GA 30022 Tel: +1 678 258 1637 | Fax: +1 678 258 1681 To: File From: James L. Stortz Subject: S6-MCM0, FCC ID: R7PNG0R1X8 Modular Approval Request May 25, 2022 Scope 47CFR 15.212 communicates requirements for products requesting modular approval. In particular, eight requirements are enumerated along with a request that each of the eight be explained for any product requesting such approval. It is the purpose of this document to respond to those eight requirements in regard to the Landis+Gyr product: S6-MCM0. Modular Approval Requirements 1.1 RF Shielding The S6-MCM0 module is self-shielding and is not dependent on any component or characteristic of the device into which it is embedded. Shielding is accomplished through a combination of metallic self-shielding components, copper planes, guards, and vias in the PCB. The result is a design that has been proven to be neither sensitive to outside influence nor capable of introducing interference into outside components. 1.2 Buffered Modulation / Data Inputs The S6-MCM0 module does not have external modulation or data inputs. Rather, the RF sections are driven by an on-board microprocessor which directly controls the RF data lines and operates so as to not allow excessive modulation. 1.3 Power Supply Regulation The S6-MCM0 module uses linear, low-dropout regulators to provide all the electronics with a supply that is fixed, even when the input voltage is varied. 1.4 Antenna Requirement The S6-MCM0 module is does not come with an antenna. It is designed to be integrated with a host board that provides the antenna. 1.5 Stand-Alone Testing All testing on the S6-MCM0 module was conducted standalone, on a host board. No shields or enclosures were used, other than those fully integrated into the modules themselves. No ferrites were used on data or power lines during testing. These devices are DC powered, and exceed applicable conducted emission requirements. 1.6 Labeling The S6-MCM0 is a small printed-circuit board module that will be supplied on reel. The FCC ID will be on a label placed on the reel. In addition, devices into which they are placed will have labels indicating that this module is contained within. Exact text will be as specified in 47CFR 15.212. 1.7 Specific Rules and Operating Requirements The S6-MCM0 module complies with all pertinent rules for its section. 1.8 RF Exposure Requirements The S6-MCM0 module complies with all exposure requirements. As a component used in the Utility industry, this product is not intended for use near human operators. 2.0 In Reference to 15.212(b) The S6-MCM0 module is always professionally installed and is not sold to the general public. This module undergoes continuous, rigorous testing to ensure that full compliance is always maintained. Sincerely, James L. Stortz Title: Head of Communication Hardware Delivery

Figure 1: Top View Figure 2: Bottom View

S6-MCM0 FCC/IC Label Information S6-MCM0 is a modular approved radio module. The label requirement is as follows. For the S6-MCM0, the label will be populated with the FCC/IC information below. Model: S6-MCM0 FCC ID: R7PNG0R1X8 IC: 5294A-NG0R1X8 Due to size limitations this label is placed on the reel and packaging material containing the module.

Figure 1: Top View Figure 2: Bottom View

5945 Cabot Parkway Suite 100 Alpharetta, GA 30005 USA Certification Exhibit FCC ID: R7PNG0R1X8 FCC Rule Part: 47 CFR Part 2.1091 Project Number: 72174490 Manufacturer: Landis + Gyr Technology, Inc Host Models: S6-MCM0 RF Exposure Model(s): S6-MCM0 Module FCC ID: R7PNG0R1X8 Report: AT72174490.5C0 Page 2 General Information: Applicant: Landis+Gyr Technology, Inc Device Category: Mobile Environment: General Population/Uncontrolled Exposure Technical Information: Antenna Type: Printed Inverted-F Antenna Antenna Gains: 1dBi Maximum Transmitter Conducted Power: 28.42dBm, 695.02mW Maximum System EIRP: 29.42dBm, 874.98mW Exposure Conditions: 20 centimeters MPE Calculation The Power Density (mW/cm 2 ) is calculated as follows: S = 2 4R PG  Where: S = power density (in appropriate units, e.g. mW/cm2) P = power input to the antenna (in appropriate units, e.g., mW) G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna (appropriate units, e.g., cm) Table 1: MPE Calculation Transmit Frequency (MHz) Radio Power (dBm) Power Density Limit (mW/cm 2 ) Radio Power (mW) Antenna Gain (dBi) Antenna Gain (mW eq.) Distance (cm) Power Density (mW/cm 2 ) 902.2 28.42 0.60 695.02 1 1.259 20 0.174

TÜV SÜD America 5945 Cabot Parkway, Suite 100 Alpharetta, GA 3005 Phone: 678-341-5900 www.tuv-sud-america.com TÜV SÜD SIGNATURE NAME JOB TITLE RESPONSIBLE FOR ISSUE DATE Kirby Munroe Wireless / EMC Technical and Certification Manager, NA TUV SUD America Inc. Authorized Signatory 2/17/2022 Signatures in this approval box have checked this document in line with the requirements of TÜV SÜD America, Inc. document control rules. FCC Accreditation Designation Number US1233 FCC Test Site Registration Number 967699 Innovation, Science, and Economic Development Canada Lab Code 23932 EXECUTIVE SUMMARY A sample of this product was tested and found to be compliant with the standards listed above. A2LA Cert. No. 2955.09 DISCLAIMER AND COPYRIGHT This non-binding report has been prepared by TÜV SÜD America with all reasonable skill and care. The document is confidential to the potential Client and TÜV SÜD America. No part of this document may be reproduced without the prior written approval of TÜV SÜD America. © TÜV SÜD. ACCREDITATION Our A2LA Accreditation does not cover opinions and interpretations and any expressed are outside the scope of our A2LA Accreditation. Report on the Testing of the Landis + Gyr Technology, Inc. S6-MCM0 In accordance with: FCC 47 CFR part 15.247 ISED RSS-247 Issue 2, February 2017 Prepared for: Landis + Gyr Technology, Inc. 30000 Mill Creek Ave., Suite 100 Alpharetta, GA 30022 COMMERCIAL-IN-CONFIDENCE Document Number: AT72174490.1C0 Document Number: AT72172744.1C0 COMMERCIAL-IN-CONFIDENCE Page 2 of 46 Contents Report Summary .........................................................................................................................3 Report Modification Record ...........................................................................................................3 Introduction ....................................................................................................................................3 Brief Summary of Results .............................................................................................................5 Product Information .......................................................................................................................6 Deviations from the Standard ........................................................................................................9 EUT Modification Record ........................................................................................................... 10 Test Location .............................................................................................................................. 10 Test Details ............................................................................................................................... 11 Antenna Requirement ................................................................................................................ 11 Power Line Conducted Emissions ............................................................................................. 12 Peak Output Power .................................................................................................................... 15 Average Output Power ............................................................................................................... 17 Carrier Frequency Separation .................................................................................................... 19 Number of Hopping Channels .................................................................................................... 21 Channel Dwell Time ................................................................................................................... 24 20dB / 99% Bandwidth ............................................................................................................... 25 Maximum Power Spectral Density in the Fundamental Emission ............................................. 31 Band-Edge Compliance of RF Conducted Emissions ............................................................... 33 RF Conducted Spurious Emissions ........................................................................................... 36 Radiated Spurious Emissions into Restricted Frequency Bands ............................................... 38 Test Equipment Used ................................................................................................................. 43 Diagram of Test Set-ups .......................................................................................................... 44 Accreditation, Disclaimers and Copyright............................................................................. 46 Document Number: AT72172744.1C0 COMMERCIAL-IN-CONFIDENCE Page 3 of 46 Report Summary Report Modification Record Alterations and additions to this report will be issued to the holders of each copy in the form of a complete document. Table 1.1-1 – Modification Record Issue Description of Change Date of Issue 0 First Issue 2/17/2022 Introduction The purpose of this report is to demonstrate compliance with Part 15 Subpart C of the FCC’s Code of Federal Regulations Section 15.247 and Innovation Science and Economic Development Canada’s Radio Standards Specification RSS-247 for the tests documented herein. Applicant Raghav Goteti Manufacturer Landis + Gyr Technology, Inc Applicant’s Email Address [email protected] Model Number(s) S6-MCM0 Serial Number(s) N/A Module FCC ID R7PNG0R1X8 Module ISED Certification Number 5294A-NG0R1X8 Hardware Version(s) 25-2564 Rev.AK Software Version(s) S6-MCM0 SBS Mode FW: S6SR3D-22.50.001 S6-MCM0 WiSUN Mode FW: S6WR3D-24.01.C04 Number of Samples Tested 2 Test Specification/Issue/Date US Code of Federal Regulation (CFR): Title 47, Part 15, Subpart C: Radio Frequency Devices, Intentional Radiators, 2021 ISED Canada Radio Standards Specification: RSS-247 – Digital Transmission Systems (DTSs), Frequency Hopping Sys…

Text truncated - open the document above for the full version.

5945 Cabot Parkway Suite 100 Alpharetta, GA 30005 USA Certification Exhibit Module FCC ID: R7PNG0R1X8 Module IC: 5294A-NG0R1X8 FCC Rule Part: 15.247 ISED Canada Radio Standards Specification: RSS-247 Project Number: 72174490 Manufacturer: Landis+Gyr Technology, Inc. Model: S6-MCM0 Test Setup Photos 5945 Cabot Parkway Suite 100 Alpharetta, GA 30005 USA Figure:1 – Test Set up - Radiated Emissions <30 MHz Figure:2 – Test Set up - Radiated Emissions <1 GHz 5945 Cabot Parkway Suite 100 Alpharetta, GA 30005 USA Figure:3 – Test Set up - Radiated Emissions <10 GHz Figure:4 – Test Set up – Antenna Port measurements 5945 Cabot Parkway Suite 100 Alpharetta, GA 30005 USA Figure:5 – Test Set up – Conducted Emissions