R7T2001102A Bluetooth module.

USER MANUAL SKOLL-I 2620011024000 VERSION0.1 JULY22, 2024 *************** MUST READ Check for firmware updates Before using the product make sure you use the most recent firmware version, data sheet and user manual. This is especially important for Wireless Connectivity products that were not purchased directly from Würth Elektronik eiSos. A firmware update on these respective products may be required. We strongly recommend to include in the customer system design, the possibility for a firmware update of the product. WIRELESS CONNECTIVITY & SENSORS User manual Skoll-I Revision history Manual version FW version HW version NotesDate 0.11.4.16.162.0 •Initial version July 2024 Order code 26200110240001 Version 0.1, July 2024www.we-online.com/wcs WIRELESS CONNECTIVITY & SENSORS User manual Skoll-I Abbreviations AbbreviationNameDescription BRBasic RateBluetooth ® Classic legacy radio mode EDR Enhanced Data Rate Bluetooth ® Classic radio mode with 2 and 3 Mbps for faster data transmittion HID Human Interface Device HIGHHigh signal level LOWLow signal level LRMLong Range Mode Tx mode increasing the RX sensitivity by using spreading and forward error correction PDS Power Down Sleep RFRadio Frequency Describes everything relating to the wireless transmission. SPPSerial Port Profile Standardized Bluetooth ® Classic profile for serial data transmission UART Universal Asynchronous Receiver Transmitter The UART allows communicating with the module via serial interface. VDDSupply voltage Order code 26200110240002 Version 0.1, July 2024www.we-online.com/wcs WIRELESS CONNECTIVITY & SENSORS User manual Skoll-I Contents Overview of helpful application notes5 1 Introduction6 1.1Operational description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 1.1.1 Key features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 1.2Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 1.3Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 2 Electrical specifications8 2.1Recommended operating conditions . . . . . . . . . . . . . . . . . . . . . . . .8 2.2Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 2.3Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 2.3.1 Static . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 2.4Radio characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 2.5Pin characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 3 Pinout11 4 Firmware history14 5 Design in guide15 5.1Advice for schematic and layout . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 6 Reference design18 6.1EV-Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 6.1.1 Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 6.1.2 Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 7 Manufacturing information21 7.1Moisture sensitivity level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 7.2Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 7.2.1 Reflow soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 7.2.2 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 7.2.3 Potting and coating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 7.2.4 Other notations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 7.3ESD handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 7.4Safety recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 8 Physical specifications25 8.1Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 8.2Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 9 Marking26 9.1Lot number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 9.2General labeling information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 10 Information for explosion protection28 Order code 26200110240003 Version 0.1, July 2024www.we-online.com/wcs WIRELESS CONNECTIVITY & SENSORS User manual Skoll-I 11 References29 12 Regulatory compliance information30 12.1 Conformity assessment of the final product . . . . . . . . . . . . . . . . . . . . 30 12.2 Exemption clause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 12.3 FCC Compliance Statement (US) . . . . . . . . . . . . . . . . . . . . . . . . . . 31 12.4 IC Compliance Statement (Canada) . . . . . . . . . . . . . . . . . . . . . . . . 31 12.5 FCC and IC requirements to OEM integrators . . . . . . . . . . . . . . . . . . . 31 12.6 Pre-certified antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 12.7 TELEC radio law approval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 12.7.1 Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 12.7.2 Certified antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 12.8 Certification of the end device . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 13 Important notes35 14 Legal notice35 15 License terms36 Order code 26200110240004 Version 0.1, July 2024www.we-online.com/wcs WIRELESS CONNECTIVITY & SENSORS User manual Skoll-I Overview of helpful application notes Application note ANR010 - Range estimation http://www.we-online.com/ANR010 This application note presents the two most used mathematical range estimation models, Friis and two ray ground reflection, and its implementation in the range estimation tool of the RED- EXPERT. Application note ANR016 - Radio module migration guide http://www.we-online.com/ANR016 Due to our long term availability policy Würth Elektronik eiSos offers beside radio…

Text truncated - open the document above for the full version.

Würth Elektronik eiSos GmbH & Co. KG Max-Eyth-Str. 1 · 74638 Waldenburg, Germany Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date：23/08/2024 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: R7T2001102 Würth Elektronik eiSos GmbH & Co. KG (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Gudrun Eckhardt Rev 1/26/2023 Würth Elektroni k eiSos GmbH & Co. KG Max-Eyth-Str . 1 · 74638 Waldenburg, Germany Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 23/08/2024 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: R7T2001102 Würth Elektroni k eiSos GmbH & Co. KG (“the applicant”) certifies that, as of th e dat e of th e filing o f the application, the applican t is not iden tified on the Covered List (as a specifically named entity o r any of it s subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely, (Applicant signature) Gudrun Eckhardt Rev 1/26/2023

Applicant ́s name: Würth Elektronik eiSos GmbH & Co. KG Applicant ́s address: Max-Eyth-Str. 1 · 74638 Waldenburg, Germany Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: 2024/08/23 SUBJECT: 2620011024000 To Whom It May Concern: I, the undersigned, hereby states this equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules, and will apply the Supplier's Declaration of Conformity procedure to the class B computer peripheral portion of this composite device. I understand the following FCC requirements: 1. Devices subject to the SDoC procedure are required to be tested to show compliance with the FCC technical regulations by a recognized accredited testing laboratory. The testing laboratory must be accredited by a Commission approved accreditation body or designated under the terms of a government-to-government Mutual Recognition Agreement (MRA). A listing of those accredited testing laboratories that have been recognized by the Commission is published on the FCC Webpage: https://apps.fcc.gov/oetcf/eas/reports/TestFirmSearch.cfm (Select the "accredited" option to search for FCC recognized accredited test firms.) 2. Pt 2.1077 contains the list of information that must be included in the Supplier's Declaration of Conformity, which must be supplied with each product sold. The SDoC compliance info shall be included in the User’s Manual or as a separate sheet. The info must contain the name, address, and phone number of the responsible party, which must be located within the United States. According to 2.909(b), the responsible party is either the Manufacturer or if the product is imported the Importer. Regards, Würth Elektronik eiSos GmbH & Co. KG ------------------------------ - （Gudrun Eckhardt）

1 Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Straße 1  74638 Waldenburg  Germany Tel. +49 7942 945-0  Fax +49 7942 945-5000 [email protected]  www.we-online.com Internal Würth Elektronik eiSos GmbH & Co. KG  Max-Eyth-Str. 1  74638 Waldenburg Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Date: 2024/09/02 SUBJECT: FCC ID: R7T2001102 To Whom It May Concern: We, the undersigned, hereby authorize ____ DEKRA Testing and Certification (Suzhou) Co., Ltd Yingfei Wang _at No.99 Hongye Rd., Suzhou Industrial Park, Suzhou, 215006, Jiangsu, China _ on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by ___ DEKRA Testing and Certification (Suzhou) Co., Ltd _ YingfeiWang ____ on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti- Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Regards, _____________________ Name：Gudrun Eckhardt (Must be signed by the person that is listed on the FCC Website) Würth Elektronik eiSos GmbH & Co. KG Sitz Waldenburg, Registergericht Stuttgart HRA 580801 Komplementär Würth Elektronik eiSos Verwaltungs-GmbH, Sitz Waldenburg, Registergericht Stuttgart HRB 581033 Geschäftsführer Thomas Wild, Alexander Gerfer, Dirk Knorr, Josef Wörner Bankverbindung UniCredit Bank AG Stuttgart, Konto 322 620 136, BLZ 600 202 90, IBAN DE86 6002 0290 0322 6201 36, SWIFT/BIC HYVEDEMM473 USt.-IdNr. DE220618976

Rev 11/20/07 (Würth Elektronik eiSos GmbH & Co. KG) Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: R7T2001102. Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Exhibit Type File Name Block Diagram Schematics Operational Description Bom PCB Layout Block Diagram.pdf Schematics.pdf Operation Description.pdf Bom.pdf PCB Layout.pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Pursuant to DA04-1705 June 15, 2004 of the Commission’s public notice, we also request temporary confidential treatment of information accompanying this application as outlined below: Exhibit Type File Name Sincerely, Gudrun Eckhardt

Date (23/08/2024) Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Modular Approval Request FCC ID: R7T2001102 The following attestation addresses the requirements to support modular approval: Modular approval requirement Yes (provide brief statement) No * (a) The radio elements must have the radio frequency circuitry shielded. Physical components and tuning capacitor(s) may be located external to the shield, but must be on the module assembly Refer to external photos. This module has shield cover. (b) The module must have buffered modulation/data inputs to ensure that the device will comply with Part 15 requirements with any type of input signal All inputs to the modules are buffered through logic or microprocessor inputs. Refer to Schematics. (c) The module must contain power supply regulation on the module The Module uses the chip SX1262 with built-in power management components, the module ratedpower is 3.3V power, Refer to schematics. (d) The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s), per Sections 15.203, 15.204(b), 15.204(c), 15.212(a), 2.929(b) The modular transmitter has a PCB antenna/FPC antenna with IPEX connector and chip antenna arrangement for LoRa, Refer to External photo. (e) The module must demonstrate compliance in a stand-alone configuration The modular transmitter is connected to the controlled board when testing. Please refer to setup photo. (f) The module must be labelled with its permanently affixed FCC ID label, or use an electronic display (See KDB Publication 784748 about labelling requirements) Refer to the label. (g) The module must comply with all specific rules applicable to the Refer to manual transmitter. The grantee must provide comprehensive instructions to explain compliance requirements Modular approval requirement Yes (provide brief statement) No * (h) The module must comply with RF exposure requirements The EUT meets RF exposure evaluation §2.1091, If the device built into a host as a portable usage, the additional RF exposure evaluation may be required as specified by §2.1093 *Please provide a detailed explanation if the answer is “No.” Sincerely, Signed: Printed name: Gudrun Eckhardt Title: Manager

Page: 1 of 2 (1) EUT Photo (2) EUT Photo Page: 2 of 2 (3) EUT Photo

Skoll-I/2620011024000 label information The Skoll-I label is lasered on the shield of the radio module. It contains the article number “2620011024000”, the FCC, IC and MIC ID. Extended radio module certification information are placed in the user manual in the chapter “regulatory compliance”, as well as on the label of the packaging. Placement of the packaging label Packaging label Placement of the module label 2620011024000 FCC ID: R7T2001102 IC: 5136A-2001102 R 217-241561

Page: 1 of 1 (1) EUT Photo (2) EUT Photo

SAR Exemption Evaluation Report Product Name : 2620011024000 Model No. : 2620011024000 FCC ID : R7T2001102 Applicant : Würth Elektronik eiSos GmbH & Co. KG Address : Max-Eyth-Str. 1 · 74638 Waldenburg, Germany Date of Receipt : Jan. 11, 2019 Issued Date : Aug. 23, 2024 Report No. : 2470363R-RF-US-P20V02 Report Version : V1.0 The test results relate only to the samples tested. The test results shown in the test report are traceable to the national/international standard through the calibration of the equipment and evaluated measurement uncertainty herein. This report must not be used to claim product endorsement by A2LA or any agency of the government. The test report shall not be reproduced without the written approval of DEKRA Testing & Certification (Suzhou) Co., Ltd. Report No: 2470363R-RF-US-P20V02 Page: 2 of 6 Te s t R e p o r t C e r t i f i c a t i o n Issued Date : Aug. 23, 2024 Report No. : 2470363R-RF-US-P20V02 Product Name : 2620011024000 Applicant : Würth Elektronik eiSos GmbH & Co. KG Address : Max-Eyth-Str. 1 · 74638 Waldenburg, Germany Manufacturer : Würth Elektronik eiSos GmbH & Co. KG Address : Max-Eyth-Str. 1 · 74638 Waldenburg, Germany Factory : Würth Elektronik eiSos GmbH & Co. KG Address : Max-Eyth-Str. 1 · 74638 Waldenburg, Germany Model No. : 2620011024000 Trade name FCC ID : : R7T2001102 EUT Voltage : 1,71-3,3Vdc Test Voltage : 3.0 Vdc Applicable Standard : FCC Part 2.1093 Test Result : Complied Performed Location : DEKRA Testing & Certification (Suzhou) Co., Ltd. No.99 Hongye Rd., Suzhou Industrial Park, Suzhou, 215006, Jiangsu, China TEL: +86-512-6251-5088 / FAX: +86-512-6251-5098 FCC Designation Number: CN1199 Tested By : (Project Engineer : Jun Xu) Approved By : (Manager : Jack Zhang ) Report No: 2470363R-RF-US-P20V02 Page: 3 of 6 1. RF Exposure Evaluation 1.1. Limits: KDB 447498 D04 B.2 Blanket 1 mW Blanket Exemption The 1 mW Blanket Exemption of § 1.1307(b)(3)(i)(A) applies for single fixed, mobile, and portable RF sources with available maximum time-averaged power of no more than 1 mW, regardless of separation distance. The 1 mW blanket exemption applies at separation distances less than 0.5 cm, including where there is no separation. This exemption shall not be used in conjunction with other exemption criteria other than those for multiple RF sources in paragraph § 1.1307(b)(3)(ii)(A). The 1 mW exemption is independent of service type and covers the full range of 100 kHz to 100 GHz, but it shall not be used in conjunction with other exemption criteria or in devices with higher-power transmitters operating in the same time-averaging period. Exposure from such higher-power transmitters would invalidate the underlying assumption that exposure from the lower-power transmitter is the only contributor to SAR in the relevant volume of tissue. B.4 SAR-based Exemption SAR-based thresholds are derived based on frequency, power, and separation distance of the RF source. The formula defines the thresholds in general for either available maximum timeaveraged power or maximum time-averaged ERP, whichever is greater. If the ERP of a device is not easily determined, such as for a portable device with a small form factor, the applicant may use the available maximum time-averaged power exclusively if the device antenna or radiating structure does not exceed an electrical length of λ/4. As for devices with antennas of length greater than λ/4 where the gain is not well defined, but always less than that of a half-wave dipole (length λ/2), the available maximum time-averaged power generated by the device may be used in place of the maximum time-averaged ERP, where that value is not known. The separation distance is the smallest distance from any part of the antenna or radiating structure for all persons, during operation at the applicable ERP. In the case of mobile or portable devices, the separation distance is from the outer housing of the device where it is closest to the antenna. Report No: 2470363R-RF-US-P20V02 Page: 4 of 6 The SAR-based exemption formula of § 1.1307(b)(3)(i)(B), repeated here as Formula (B.2), applies for single fixed, mobile, and portable RF sources with available maximum time-averaged power or effective radiated power (ERP), whichever is greater, of less than or equal to the threshold Pth (mW). This method shall only be used at separation distances from 0.5 cm to 40 cm and at frequencies from 0.3 GHz to 6 GHz (inclusive). Pth is given by Formula (B.2). and f is in GHz, d is the separation distance (cm), and ERP 20cm is per Formula (B.1). The example values shown in Table B.2 are for illustration only. Table B.2—Example Power Thresholds (mW) Report No: 2470363R-RF-US-P20V02 Page: 5 of 6 1.2. Test Procedure Software provided by client enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. The temperature and related humidity: 18°Cand 78％ RH. 1.3. Test Result of RF Exposure Evaluation Product : 2620011024000 Test Item : RF Exposure Evaluation Test Site : AC-6 ⚫ Antenna Information Antenna manufacturer N/A Antenna Delivery 1*TX+1*RX 2*TX+2*RX 3*TX+3*RX Antenna technology SISO MIMO Basic CDD Beam-forming Antenna Type External Dipole Internal PIFA PCB Ceramic Chip Antenna Stamping Antenna Metal plate type F antenna Monopole antenna Antenna Gain -0.5dBi Report No: 2470363R-RF-US-P20V02 Page: 6 of 6 1.4. Test Result of RF Exposure Evaluation B.2 Blanket 1 mW Blanket Exemption Test Mode Frequency Band (MHz) Maximum conducted Power (dBm) Maximum ERP Power (dBm) Maximum Power (mW) R (mm) Limit (mW) Result BT 2402 ~ 2480 4.41 2.21 2.76 5.0 1 Not applicable Note: BT does not comply with B.2 Blanket 1 mW Blanket Exemption, we use B.4 SAR-based Exemption for evaluation. B.4 SAR-based Exemption Test Mode Frequency Band (MHz) Maximum conducted Power (dBm) Maximum ERP Power (dBm) Maximum Power (mW) Distance (mm) Limit (mW) Result BT 2402 ~ 2480 4.41 1.76 2.76 5.0 3.0 SAR was not required. Note: This report is based on FCC ID: WA…

Text truncated - open the document above for the full version.

Antenna dimension Antenna Specification Properties at 2.44 GHz Nano Antenna Appearance Dimensions (mm) clearance area included 4.4*10 Type PCB Antenna Frequency range 2400 MHz ~ 2500 MHz Peak Gain (dBi) -0.5 Radiated Pattern

Test Report FCC Part15 Subpart C & RSS-247 Issue 3 Product Name : 2620011024000 Model No. : 2620011024000 FCC ID : R7T2001102 IC : 5136A-2001102 Applicant : Würth Elektronik eiSos GmbH & Co. KG Address : Max-Eyth-Str. 1 · 74638 Waldenburg, Germany Date of Receipt : Jan. 11, 2019 Test Date : Jan. 12, 2019 ~ Feb. 19, 2019 Issued Date : Aug. 23, 2024 Report No. : 2470363R-RF-US-P06V02 Report Version : V1.0 The test results relate only to the samples tested. The test results shown in the test report are traceable to the national/international standard through the calibration of the equipment and evaluated measurement uncertainty herein. This report must not be used to claim product endorsement by A2LA or any agency of the government. The test report shall not be reproduced without the written approval of DEKRA Testing & Certification (Suzhou) Co., Ltd. Report No: 2470363R-RF-US-P06V02 Page: 2 of 84 Te s t R e p o r t C e r t i f i c a t i o n Issued Date: Aug. 23, 2024 Report No. : 2470363R-RF-US-P06V02 Product Name : 2620011024000 Applicant : Würth Elektronik eiSos GmbH & Co. KG Address : Max-Eyth-Str. 1 · 74638 Waldenburg, Germany Manufacturer : Würth Elektronik eiSos GmbH & Co. KG Address : Max-Eyth-Str. 1 · 74638 Waldenburg, Germany Factory : Würth Elektronik eiSos GmbH & Co. KG Address : Max-Eyth-Str. 1 · 74638 Waldenburg, Germany Model No. : 2620011024000 Trade name : FCC ID : R7T2001102 IC : 5136A-2001102 EUT Voltage : 1.71-3.3 Vdc Test Voltage : 3.0Vdc Applicable Standard : 47 CFR FCC Part 15 (Section 15.247) ANSI C63.10: 2013 RSS-Gen Issue 5 RSS-247 Issue 3 Test Result : Complied Performed Location : DEKRA Testing & Certification (Suzhou) Co., Ltd. No.99 Hongye Rd., Suzhou Industrial Park, Suzhou, 215006, Jiangsu, China TEL: +86-512-6251-5088 / FAX: +86-512-6251-5098 FCC Designation Number: CN1199; ISED Lab Code: 4075B Tested By : (Project Engineer: Jun Xu) Approved By : (Manager: Jack Zhang ) Report No: 2470363R-RF-US-P06V02 Page: 3 of 84 TABLE OF CONTENTS Description Page 1. General Information ................................................................................................. 6 1.1. EUT Description ...................................................................................................... 6 1.2. Working Frequency of Each Channel: ..................................................................... 6 1.3. Antenna information ................................................................................................ 7 1.4. Mode of Operation ................................................................................................... 8 1.5. Tested System Details ............................................................................................. 8 1.6. Configuration of Tested System ............................................................................... 9 1.7. EUT Exercise Software.......................................................................................... 10 2. Technical Test ........................................................................................................ 11 2.1. Summary of Test Result......................................................................................... 11 2.2. Test Frequency configuration:................................................................................ 13 2.3. Test Environment ................................................................................................... 14 2.4. Measurement Uncertainty ..................................................................................... 14 3. AC Power Line Conducted Emission ..................................................................... 15 3.1. Test Equipment ...................................................................................................... 15 3.2. Test Setup ............................................................................................................. 15 3.3. Limit ....................................................................................................................... 16 3.4. Test Procedure ...................................................................................................... 16 3.5. Test Result ............................................................................................................. 17 4. Emissions in restricted frequency bands ............................................................... 17 4.1. Test Equipment ...................................................................................................... 18 4.2. Test Setup ............................................................................................................. 19 4.3. Limit ....................................................................................................................... 20 4.4. Test Procedure ...................................................................................................... 23 4.5. EUT test Axis definition .......................................................................................... 24 4.6. Test Result ............................................................................................................. 25 5. Emissions in non-restricted frequency bands ........................................................ 39 5.1. Test Equipment ...................................................................................................... 39 5.2. Test Setup ............................................................................................................. 39 5.3. Limit ....................................................................................................................... 40 5.4. Test Procedure ...................................................................................................... 41 5.5. EUT test Axis definition .......................................................................................... 42 5.6. Test Result ............…

Text truncated - open the document above for the full version.

FCC Part15.247&IC Test Setup Photograph Description: Radiated Emission Test Setup for Below 1GHz Description: Radiated Emission Test Setup for 1~18GHz Description: Radiated Emission Test Setup for Above 18GHz Description: Conducted Test Setup