RA8-BC008Bluetooth Speakerphone

13 2 5 4 7 6 User Manual 1. About Bluetooth Speakerphone This versatile Bluetooth speakerphone is specially designed for user to enjoy convenience and freedom of wireless communication. Dual capacity of use on desk-top like a Conference Speakerphone and in-car like a Hands-free car kit. Advanced built-in microphone with D.S.P. solution for Echo Cancellation & Noise Suppression that gives you impeccable full duplex sound quality. 2. About Bluetooth Technology Bluetooth wireless technology is set to revolutionize the personal connectivity by providing freedom from wired connections-enabling links and connectivity between notebook/laptop, mobile phones, portable handheld devices and other Bluetooth enabled devices within 10 meters. Utilizing global sound & digital data 2.4GHz ISM transmission, it makes global communication in the way you’ve never dreamed of! 3. Appearance and Function (1) Speaker (2) Microphone (3) LED (4) Charging Socket (5-pin USB) (5) Mute Button (6) MFB Button (Multi-Function Button) (7) Volume Increase (V+) (8) Volume Decrease (V-) (9) Solar Panel (10) Windshield Mount 4. Recommend Installation Position It is recommended that the speakerphone is positioned on to the top of the left side of the windshield as shown in the pictures below: WARNING: Do not place or store the speakerphone over the area of the automobiles safety airbag deployment, or it may cause serious injury when a safety airbag deploys. 5. Charging Your Bluetooth Speakerphone The Bluetooth speakerphone comes with a built-in rechargeable battery. Prior to using the speakerphone, it is recommended to charge the battery fully for the first time. Using the car charger • Insert the car charger completely into the charging slot until the LED flash red. • Normal full charge time is 3 hours. (approx.), and the LED will flash off when charge is completed. Using solar power • Direct the solar panel on the back side of the speakerphone toward sun. (Please refer to the recommended installation position, as mentioned above.) • If the speakerphone receives sufficient sunlight for 2 hours, you can talk for duration of up to 1 hour. Using solar power charge, the operation time (the talk time and the standby time) will be extended continuously without any additional charge required by the car charger. WARNING: Do not attempt to charge the speakerphone with any charger other than the one provided. Using another charger may damage or destroy the speakerphone. 6. Turning ON/OFF the Speakerphone Power On: When speakerphone is under off mode, press and hold the “MFB” for 4 seconds until you hear a short beep. The blue LED will flash 5 times, and then the speakerphone will automatically connect to the last connected mobile phone. Power Off: Speakerphone is under standby mode, press and hold the “MFB” button for 4 seconds until you hear a short beep. The red LED will flash 5 times before power off. 7. Pairing Prior to using the speakerphone for the first time, you must pair it with a Bluetooth enabled mobile phone. The steps below describe pairing instructions for a typical Bluetooth enabled mobile phone. (1) Place the speakerphone and mobile phone no more than 1 meter (3 feet) apart. (2) Ensure the speakerphone is turned off. (3) Press and hold the “MFB” button for 6 seconds until the LED flash red and blue alternatively, it is now ready for pairing. (4) Activate the Bluetooth function on your mobile phone and search for accessible Bluetooth device by referring to your mobile phone user guide for details. (5) Select “BT Speaker” from the list of searched devices. (6) Enter the pre-programmed code “0000” and press “OK” to pair the speakerphone and the phone. (7) When pairing is completed, the speakerphone is under the standby mode with the blue LED flashes in every 3 seconds. Please place the mobile phone and the speakerphone within 10 meters (32 feet) sensing distance. NOTE: If the pairing cannot be completed within 2 minutes after the pairing mode is activated, the speakerphone will power off automatically. Please repeat steps above to pair the speakerphone and mobile phone again. 8. Connection/Link between Speakerphone and Mobile Phone After pairing is completed, speakerphone is always under standby mode. Before you place or answer a call, if the headset icon is not shown on phone screen, please follow the steps below to activate the Bluetooth connection/link through your mobile phone or speakerphone until the headset icon is on the screen. • On phone: Select the “BT Speaker” from the paired list on your mobile phone’s Bluetooth menu. • On speakerphone: Short press “MFB” and select “Accept” on phone screen to accept connection. 9. Disconnection between Speakerphone and Mobile Phone When you need to connect your speakerphone with another Bluetooth enabled mobile phone, please follow the steps below to disconnect the speakerphone with the pre-paired mobile phone. • On phone: Select “Disconnecting” on the Bluetooth device list of your mobile phone’s Bluetooth menu to remove the connection. • On speakerphone: Power off the speakerphone. NOTE: When losing the connection/link, the speakerphone will turn off automatically in 15 minutes. The blue LED will flash twice in every 3 seconds when the speakerphone is not connected with mobile phone. 10. Using the Speakerphone (1) Answering a Call When receiving a phone call, short press the “MFB” button to answer the call. (2) Ending a Call Short press the “MFB” button to end a call. (3) Reject a Call When you hear the ringing tone, press and hold the “MFB” button for 2 seconds to reject the call. (4) Voice Dial If your mobile phone is voice dialing enabled, under standby mode, short press the “MFB” button and say the voice tag after you hear a beep. Note: Please make sure to record voice tag into the mobile phone before using voice dial function. Functionality varies depending on the mobile phone models. Please refer to your mobile phone user guide for details. (5) Last Number Re-Dialing U…

Text truncated - open the document above for the full version.

Applicant letterhead Sunitec Enterprise Co.,Ltd To: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 To whom it may concern: We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch to act on our behalf, as our agent, in the following matters related to the FCC approval of our product: report submittal, related correspondence, the signing of all documents relating to these matters, and any other lawful activity necessary to obtain such certification. Any act carried out by SGS within the scope of this authorization shall have the same effects as our own. This authorization shall expire 6 months from original date. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you. Sincerely, G.M. NOV.25, 2009 Tom Chiec -------------------------------------- Name & Title, Date Applicant: 10F.-1, No.200, Jingping Rd., Jhonghe City, Taipei County 23581 Taiwan Tel: 886 2 8943 1929 Fax: 886 2 8943 1828 Email: [email protected]

Sunitec Enterprise Co.,Ltd 2009-11-21 Federal Communications Commission Office of Engineering and Technology Equipment Authorization Division 7345 Oakland Mils Road Columbia, Maryland 21046 Subject: Permanent Confidentiality request for FCC ID: RA8-BC008 To Whom It May Concern, Pursuant to sections 0.457 and 0.459 of CFR47, the applicant requests permanent confidential treatment of the following information accompanying this application: Block Diagrams Schematics Operation Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the applicant and provide unjustified benefits to its competitors. Sincerely, G.M. NOV,25 2009 -------------------------------------- Name & Title, Date Applicant: 10F.-1, No.200, Jingping Rd., Jhonghe City, Taipei County 23581 Taiwan Tel: 886 2 8943 1929 Fax: 886 2 8943 1828 Email: [email protected]

SUNITEC ENTERPRISE CO., LTD. Model Confirmation Letter We, Sunitec LTD (Company name)certify the product: BC903，GBHFK231 ，BC903B， BTCK-18And BTCK-28 Their electrical circuit design, layout, components used and internal wiring are identical, Only appearance is different. Grantee Contact: Signiture: Tom Chien Company Name:(Chop) Date:2009-11-25

1 Photographs - EUT Constructional Details SGS-CSTC Standards Technical Services Ltd. Report No.: SZEMO09110651501 Page: 2 of 4 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” SGS-CSTC Standards Technical Services Ltd. Report No.: SZEMO09110651501 Page: 3 of 4 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” SGS-CSTC Standards Technical Services Ltd. Report No.: SZEMO09110651501 Page: 4 of 4 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

23.0 mm 6.8 mm Sunitec Enterprise CO., Ltd. Model: BC903 Bluetooth Speakerphone Input: 5V 400mA FCC ID: RA8-BC008 Made in China Sunitec Enterprise CO., Ltd. Model: BC903 Bluetooth Speakerphone Input: 5V 400mA FCC ID: RA8-BC008 Made in China

SGS-CSTC Standards Technical Services Ltd. Report No.: SZEMO09110651501 Page: 2 of 3 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” SGS-CSTC Standards Technical Services Ltd. Report No.: SZEMO09110651501 Page: 3 of 3 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Ltd. No. 1 Workshop, M-10, Middle section, Science & Technology Park, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEMO09110651501 Page: 1 of 60 Authorized Signature: Robinson Lo Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover Page FCC REPORT Application No: SZEMO091106515RF Applicant: Sunitec Enterprise CO., Ltd Product Name: Bluetooth Speakerphone Operation Frequency: 2.402GHz to 2.480GHz FCC ID: RA8-BC008 Standards: FCC CFR Title 47 Part 15 Subpart C Section 15.247: 2008 Date of Receipt: 20 November 2009 Date of Test: 26 November to 09 December 2009 Date of Issue: 10 December 2009 Test Result : PASS * * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Ltd. Report No.: SZEMO09110651501 Page: 2 of 60 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Contents Page 1 COVER PAGE.........................................................................................................................................................1 2 CONTENTS.............................................................................................................................................................. 2 3 TEST SUMMARY.................................................................................................................................................... 3 4 GENERAL INFORMATION................................................................................................................................... 4 4.1 CLIENT INFORMATION.......................................................................................................................................... 4 4.2 GENERAL DESCRIPTION OF E.U.T. ....................................................................................................................... 4 4.3 E.U.T OPERATION MODE...................................................................................................................................... 6 4.4 TEST FACILITY..................................................................................................................................................... 7 4.5 TEST LOCATION................................................................................................................................................... 7 4.6 OTHER INFORMATION REQUESTED BY THE CUSTOMER........................................................................................ 7 4.7 TEST INSTRUMENTS LIST...................................................................................................................................... 8 5 TEST RESULTS AND MEASU…

Text truncated - open the document above for the full version.

1 Photographs-test setup photo Radiated Emission Conducted Emission