RAD138GSM/GPRS/EDGE dual band mobile phone

1234567 891011121314 Your cellphone 1 .................. OT-806A OT-807A Status bar icons1.1 (1) Battery charge level Vibrate alert: your cellphone vibrates, but does not ring or beep with the exception of the alarm. Bluetooth status (Activated). Bluetooth status (Connected to an audio device). Java status (Activated). Headset connected. Keypad & LCD touch locked. Keypad& LCD touch unlocked. Call forwarding activated: your calls are forwarded. Alarm or appointments programmed. Level of network reception. Wi-Fi connected. Wi-Fi disconnected. Voicemail message arrived. Missed calls. Stopwatch is active. Radio is on. WAP alerts (1) . Roaming. Memory card scanning in progress. Memory card scanning completed. SIM card unavailable. Line switching (1) : indicates the selected line. GPRS connection status (Activated). GPRS connecting. EDGE attached. EDGE connecting. Music player active. Message receipt in progress. Sending a SMS. Sending a MMS. Silence mode: your cellphone does not ring, beep or vibrate with the exception of the alarm. SMS unread. (In red) Message list is full: your cellphone cannot accept any new messages. You must access the message list and delete at least one message on your SIM card. Flight mode. A2DP connected. Broadcast is on. Status list1.2 Tap the status bar and drag down to open, drag up to close. To open an application, tap it from the list. Desktop1.3 Adding items To add an item from the main menu, you can select one of the following ways: Tap and hold an item from the main menu list.• Tap • from the tool bar and select an item. Touch and hold an empty area from the main screen, select “• Add widgets” from the window that opens, then tap the item you want to add to desktop. Removing items Touch and hold the widget you want to remove from the desktop to enter the edit mode, and then tap to remove it, finally tap “Done” to confirm. Re-organizing items Touch and hold the widget you want to move from the desktop editing screen until a location frame shows up, then drag it to the desired location, finally tap “Done” to confirm. Wallpaper To personalize your wallpaper, you can select one of the following two ways: Touch and hold an empty area from the desktop, select “• Wallpaper”, then tap a folder that displayed to select an image as your wallpaper. Tap • from the tool bar, then tap a folder to select an image as your wallpaper. Toolbar1.4 Tool bar with menu items by default as a shortcut for quick access. Scrolling left and right, you can view more items. Getting started 2 ................. Set-up2.1 Removing or installing the back cover Inserting or removing the SIM card You must insert your SIM card to make phone calls. Please power off your cellphone and remove battery before inserting or removing the SIM card. Place the SIM card with the chip facing downwards and slide it into its housing. Make sure that it is correctly inserted. To remove the card, press and slide it out. Installing or removing the battery Insert and click the battery into place, then close the cellphone cover.• Unclip the cover, then remove the battery.• Power on your cellphone2.2 Hold down the key until the cellphone powers on. Power off your cellphone2.3 Hold down the key from the main screen. Using the touchscreen2.4 TapTo access an application, tap it with your finger. DragPlace your finger on the screen to drag the object to the destination. ScrollSlide the screen to scroll up and down the applications, images, web pages... at your convenience. Making a call 3 ...................... Enter the desired number on the on-screen keypad directly or select a contact from Call log or Directory by tapping or respectively, then tap or press key to place the call. The number you entered can be saved to Directory by selecting . If you make a mistake, you can delete the incorrect digits by tapping . To hang up the call, press the key. Menu arrange 4 ............ The main menu is designed to vary according to your preference. To access this function, select to enter the main menu, then tap . Change the order Access “Menu arrange”, focus on the main menu item you want to move, and then tap “Options\Move”, it will go to the main menu screen and tick “√” will be shown on the main menu you selected, then release it to your favourite destination. Show/Hide Access “Menu arrange”, tap the left check box of the selected menu once to show/hide, then tap “Options\Save” to save the operation. Restore default From main menu, select “Menu arrange”, then tap “Options\Restore default settings” to return to the default menu display. Messages 5 .................. Conversational On (Off) mode5.1 In conversational on mode, you can view chat history in chronological order. In conversational off mode, you may have access to the following folders: Inbox, Outbox, Sent, Broadcast SMS, Voicemail, Drafts, etc. You can switch between these two modes by selecting “Settings\Conversational mode\On (Off)”. Conversational mode is set as the default mode and following instructions are based on this mode. Create message5.2 Select “Messages\Write msg” to create text/multimedia message. An SMS will be converted to MMS automatically when: images, videos, audio, slides or attachments are inserted; Subject, CC/BCC/email address is added; or the message contains more than 8 pages of text. Timer send Schedule a SMS/MMS to be sent out at predefined time (“Option\Timer send”). Email 6 .......................... Your cellphone has an email client with the settings predefined for a few popular email services like – GoogleMail, Yahoo, AOL, etc. Besides this, you can set up other POP3 or IMAP4 email accounts that you may be using. Palringo 7 (1) .................... Palringo Instant messaging (IM) allows you to chat with other people using Palringo account. You can also connect to other popular IM services through Palringo, like Yahoo, AIM, GG, ICQ, GTalk, iChat etc. Please note that the services accessible to you will depend on your client version and…

Text truncated - open the document above for the full version.

OT-806A External Photos:

OT-806A Label Location:

OT-806A Internal Photos:

No.2010SAR00115 Page 1 of 129 ©Copyright. All rights reserved by TMC Beijing. SAR TEST REPORT No. 2010SAR00115 For TCT Mobile Limited GSM/GPRS/EDGE dual band mobile phone Amber A OT-806A With Hardware Version: lot0 Software Version: SW22B FCCID: RAD138 Issued Date: 2010-10-26 No. DGA-PL-114/01-02 Note: The test results in this test report relate only to the devices specified in this report. This report shall not be reproduced except in full without the written approval of TMC Beijing. Test Laboratory: TMC Beijing, Telecommunication Metrology Center of MIIT No. 52, Huayuan Bei Road, Haidian District, Beijing, P. R. China 100191. Tel:+86(0)10-62304633-2079, Fax:+86(0)10-62304793 Email:[email protected]. www.emcite.com No.2010SAR00115 Page 2 of 129 TABLE OF CONTENT 1 TEST LABORATORY..................................................................................................................3 1.1 TESTING LOCATION........................................................................................................................................ 3 1.2 TESTING ENVIRONMENT................................................................................................................................. 3 1.3 PROJECT DATA............................................................................................................................................... 3 1.4 SIGNATURE..................................................................................................................................................... 3 2 CLIENT INFORMATION..............................................................................................................4 2.1 APPLICANT INFORMATION.............................................................................................................................. 4 2.2 MANUFACTURER INFORMATION..................................................................................................................... 4 3 EQUIPMENT UNDER TEST (EUT) AND ANCILLARY EQUIPMENT (AE) ................................5 3.1 ABOUT EUT ................................................................................................................................................... 5 3.2 INTERNAL IDENTIFICATION OF EUT USED DURING THE TEST.......................................................................... 5 3.3 INTERNAL IDENTIFICATION OF AE USED DURING THE TEST............................................................................. 5 4 CHARACTERISTICS OF THE TEST ..........................................................................................5 4.1 APPLICABLE LIMIT REGULATIONS.................................................................................................................. 5 4.2 APPLICABLE MEASUREMENT STANDARDS...................................................................................................... 5 5 OPERATIONAL CONDITIONS DURING TEST ..........................................................................6 5.1 SCHEMATIC TEST CONFIGURATION................................................................................................................. 6 5.2 SAR MEASUREMENT SET-UP.......................................................................................................................... 6 5.3 DASY4 E-FIELD PROBE SYSTEM..................................................................................................................... 7 5.4 E-FIELD PROBE CALIBRATION........................................................................................................................ 8 5.5 OTHER TEST EQUIPMENT...............................................................................................................................9 5.6 EQUIVALENT TISSUES................................................................................................................................... 10 5.7 SYSTEM SPECIFICATIONS.............................................................................................................................. 11 6 CONDUCTED OUTPUT POWER MEASUREMENT................................................................. 11 6.1 SUMMARY.................................................................................................................................................... 11 6.2 CONDUCTED POWER.................................................................................................................................... 11 7 TEST RESULTS ........................................................................................................................13 7.1 DIELECTRIC PERFORMANCE......................................................................................................................... 13 7.2 SYSTEM VALIDATION.................................................................................................................................... 13 7.3 SUMMARY OF MEASUREMENT RESULTS....................................................................................................... 14 7.4 SUMMARY OF MEASUREMENT RESULTS (BLUETOOTH AND WIFI FUNCTION) ............................................... 16 7.5 CONCLUSION................................................................................................................................................ 19 8 MEASUREMENT UNCERTAINTY ............................................................................................19 9 MAIN TEST INSTRUMENTS ....................................................................................................21 ANNEX A MEASUREMENT PROCESS....................................................................................22 ANNEX B TEST LAYOUT .........................................................................................................23 ANNEX C GRAPH RESULTS....................................................................................................29 ANN…

Text truncated - open the document above for the full version.

No.2010SAR00115 Page 91 of 129 No.2010SAR00115 Page 92 of 129 No.2010SAR00115 Page 93 of 129 No.2010SAR00115 Page 94 of 129 No.2010SAR00115 Page 95 of 129 No.2010SAR00115 Page 96 of 129 No.2010SAR00115 Page 97 of 129 No.2010SAR00115 Page 98 of 129 No.2010SAR00115 Page 99 of 129 No.2010SAR00115 Page 100 of 129 No.2010SAR00115 Page 101 of 129 No.2010SAR00115 Page 102 of 129 No.2010SAR00115 Page 103 of 129 No.2010SAR00115 Page 104 of 129 No.2010SAR00115 Page 105 of 129 No.2010SAR00115 Page 106 of 129 No.2010SAR00115 Page 107 of 129 ANNEX F DIPOLE CALIBRATION CERTIFICATE 835 MHz Dipole Calibration Certificate No.2010SAR00115 Page 108 of 129 No.2010SAR00115 Page 109 of 129 No.2010SAR00115 Page 110 of 129 No.2010SAR00115 Page 111 of 129 No.2010SAR00115 Page 112 of 129 No.2010SAR00115 Page 113 of 129 No.2010SAR00115 Page 114 of 129 No.2010SAR00115 Page 115 of 129 No.2010SAR00115 Page 116 of 129 1900 MHz Dipole Calibration Certificate No.2010SAR00115 Page 117 of 129 No.2010SAR00115 Page 118 of 129 No.2010SAR00115 Page 119 of 129 No.2010SAR00115 Page 120 of 129 No.2010SAR00115 Page 121 of 129 No.2010SAR00115 Page 122 of 129 No.2010SAR00115 Page 123 of 129 No.2010SAR00115 Page 124 of 129 No.2010SAR00115 Page 125 of 129 2450 MHz Dipole Calibration Certificate No.2010SAR00115 Page 126 of 129 No.2010SAR00115 Page 127 of 129 No.2010SAR00115 Page 128 of 129 No.2010SAR00115 Page 129 of 129

Appendix A: SPEAG’s new calibration certifications Appendix B: SPEAG’s Evaluation report

No. 2010HAC00013 Page 1 of 57 ©Copyright. All rights reserved by TMC Beijing. HAC RF TEST REPORT No. 2010HAC00013 For TCT Mobile Limited GSM/GPRS/EDGE dual band mobile phone Amber A OT-806A With Hardware Version: lot0 Software Version: SW22B FCCID: RAD138 Results Summary: M Category = M3 Issued Date: 2010-09-28 No. DGA-PL-114/01-02 Note: The test results in this test report relate only to the devices specified in this report. This report shall not be reproduced except in full without the written approval of TMC Beijing. Test Laboratory: TMC Beijing, Telecommunication Metrology Center of MIIT No. 52, Huayuan Bei Road, Haidian District, Beijing, P. R. China 100191. Tel:+86(0)10-62304633-2079, Fax:+86(0)10-62304793 Email:[email protected]. www.emcite.com No.2010HAC00013 Page 2 of 57 TABLE OF CONTENT 1 TEST LABORATORY..................................................................................................................3 1.1 TESTING LOCATION........................................................................................................................................ 3 1.2 TESTING ENVIRONMENT................................................................................................................................. 3 1.3 PROJECT DATA............................................................................................................................................... 3 1.4 SIGNATURE..................................................................................................................................................... 3 2 CLIENT INFORMATION..............................................................................................................4 2.1 APPLICANT INFORMATION.............................................................................................................................. 4 2.2 MANUFACTURER INFORMATION..................................................................................................................... 4 3 EQUIPMENT UNDER TEST (EUT) AND ANCILLARY EQUIPMENT (AE) ................................4 3.1 ABOUT EUT ................................................................................................................................................... 4 3.2 INTERNAL IDENTIFICATION OF EUT USED DURING THE TEST.......................................................................... 4 3.3 INTERNAL IDENTIFICATION OF AE USED DURING THE TEST............................................................................. 4 4 CONDUCTED OUTPUT POWER MEASUREMENT...................................................................5 4.1 SUMMARY...................................................................................................................................................... 5 4.2 CONDUCTED POWER...................................................................................................................................... 5 5. REFERENCE DOCUMENTS......................................................................................................5 5.1REFERENCE DOCUMENTS FOR TESTING........................................................................................................... 5 6 OPERATIONAL CONDITIONS DURING TEST ..........................................................................5 6.1 HAC MEASUREMENT SET-UP.................................................................................................................. 5 6.2 PROBE SPECIFICATION.................................................................................................................................... 6 6.3 TEST ARCH PHANTOM & PHONE POSITIONER................................................................................................. 7 6.4 ROBOTIC SYSTEM SPECIFICATIONS................................................................................................................. 8 7 EUT ARRANGEMENT ................................................................................................................8 7.1 WD RF EMISSION MEASUREMENTS REFERENCE AND PLANE........................................................................ 8 8 SYSTEM VALIDATION................................................................................................................9 8.1 VALIDATION PROCEDURE...............................................................................................................................9 8.2 VALIDATION RESULT.................................................................................................................................... 10 9 PROBE MODULATION FACTOR .............................................................................................10 9.1 MODULATION FACTOR TEST PROCEDURE..................................................................................................... 11 9.2 MODULATION FACTOR.................................................................................................................................. 11 10 RF TEST PROCEDUERES .....................................................................................................12 11 HAC RF TEST DATA SUMMARY............................................................................................13 11.1 MEASUREMENT RESULTS (E-FIELD)........................................................................................................... 13 11.2 MEASUREMENT RESULTS (H-FIELD) .......................................................................................................... 13 11.3 TOTAL M-RATING....................................................................................................................................... 13 12 ANSI C 63.19-2007 LIMITS.....................................................................................................14 13 MEASUREMENT UNCERTAINTY .........................................................................................…

Text truncated - open the document above for the full version.

TEST REPORT No. 2010TAR412 for TCT Mobile Limited GSM/GPRS/EDGE dual band mobile phone Model Name: Amber A Marketing Name : OT-806A FCC ID: RAD138 with Hardware Version: lot0 Software Version: SW22B Issued Date: Oct 28, 2010 Note: The test results in this test report relate only to the devices specified in this report. This report shall not be reproduced except in full without the written approval of TMC Beijing. Test Laboratory: DAR accreditation (DIN EN ISO/IEC 17025): No. DGA-PL-114/01-02 FCC 2.948 Listed: No.733176 IC O.A.T.S listed: No.6629A-1 TMC Beijing, Telecommunication Metrology Center of Ministry of Industry and Information Technology 3/F Shou Xiang Technology Building, No.51 Xueyuan Road, Hai Dian District, Beijing, P. R. China,100191. Tel:+86(0)10-62304633-2604, Fax:+86(0)10-62304793, Email:[email protected], web: www.emcite.com No.2010TAR412 Page2 of 70 CONTENTS 1. TEST LABORATORY ......................................................................................................................... 3 1.1. TESTING LOCATION .................................................................................................................... 3 1.2. TESTING ENVIRONMENT ........................................................................................................... 3 1.3. PROJECT DATA .............................................................................................................................. 3 1.4. SIGNATURE ..................................................................................................................................... 3 2. CLIENT INFORMATION ................................................................................................................... 4 2.1. APPLICANT INFORMATION ....................................................................................................... 4 2.2. MANUFACTURER INFORMATION ............................................................................................ 4 3. EQUIPMENT UNDER TEST (EUT) AND ANCILLARY EQUIPMENT (AE) ............................. 5 3.1. ABOUT EUT ..................................................................................................................................... 5 3.2. INTERNAL IDENTIFICATION OF EUT USED DURING THE TEST .................................... 5 3.3. INTERNAL IDENTIFICATION OF AE USED DURING THE TEST ....................................... 5 3.4. GENERAL DESCRIPTION ............................................................................................................ 6 4. REFERENCE DOCUMENTS ............................................................................................................. 6 4.1. REFERENCE DOCUMENTS FOR TESTING ............................................................................. 6 5. LABORATORY ENVIRONMENT ..................................................................................................... 7 6. SUMMARY OF TEST RESULTS ....................................................................................................... 8 7. TEST EQUIPMENTS UTILIZED ...................................................................................................... 9 ANNEX A: MEASUREMENT RESULTS ................................................................................................ 1 0 A.1 OUTPUT POWER (§22.913(A)/§24.232(B)) ............................................................................... 10 A.2 EMISSION LIMT (§2.1051/§24.238) .......................................................................................... 16 A.3 CONDUCTED EMISSION (§15.107§15.207) ............................................................................. 21 A.4 FREQUENCY STABILITY (§2.1055/§24.235) ........................................................................... 28 A.5 OCCUPIED BANDWIDTH (§2.1049(H)(I)) ................................................................................. 30 A.6 EMISSION BANDWIDTH (§22.917(B)/§24.238(B)) .................................................................. 42 A.7 BAND EDGE COMPLIANCE (§22.917(B)/§24.238(B)) ................................................................ 54 A.8 CONDUCTED SPURIOUS EMISSION (§2.1057/§22.917/§24.238) ........................................... 60 No.2010TAR412 Page3 of 70 1. Test Laboratory 1.1. Testing Location Company Name: TMC Beijing, Telecommunication Metrology Center of MIIT Address: 3/F Shou Xiang Technology Building, No.51 Xueyuan Road, Hai Dian District, Beijing, P. R. China Postal Code: 100191 Telephone: 00861062304633 Fax: 00861062304793 1.2. Testing Environment Normal Temperature: 15-35°C Relative Humidity: 20-75% 1.3. Project data Testing Start Date: Sep 27, 2010 Testing End Date: Oct 28, 2010 1.4. Signature Zi Xiaogang (Prepared this test report) Sun Xiangqian (Reviewed this test report) Lu Bingsong Deputy Director of the laboratory (Approved this test report) No.2010TAR412 Page4 of 70 2. Client Information 2.1. Applicant Information Company Name: TCT Mobile Limited Address /Post: 4F, South Building, No.2966, JinKe Road, Zhangjiang High-Tech Park City: Shanghai Postal Code: 201203 Country: P.R.China Telephone: 0086 2161460890 Fax: 0086 2161460602 2.2. Manufacturer Information Company Name: TCT Mobile Limited Address /Post: 4F, South Building, No.2966, JinKe Road, Zhangjiang High-Tech Park City: Shanghai Postal Code: 201203 Country: P.R.China Telephone: 0086 2161460890 Fax: 0086 2161460602 No.2010TAR412 Page5 of 70 3. Equipment Under Test (EUT) and Ancillary Equipment (AE) 3.1. About EUT Description GSM/GPRS/EDGE dual band mobile phone Model Name Amber A Marketing Name OT-806A FCC ID RAD138 Frequency GSM 850MHz; PCS 1900MHz Antenna Internal Power supply Battery or Charger (AC Adaptor) Output power 28.58 dBm maximum ERP measured for GSM850 Extreme vol. Limits 3.5VDC to 4.2VDC (nominal: 3.8VDC) Note: Components list, please refer to documents of the manufacturer; it is also included in the…

Text truncated - open the document above for the full version.

FCCID: RAD138 Test Set up photos: Part22/24 RSE: Part15B CE: Part15B(USB mode) RE-1: Part15B(Charging mode) RE: Part15C RE:

The photos of HAC test For TCT Mobile Limited GSM/GPRS/EDGE dual band mobile phone Amber A OT-806A With Hardware Version: lot0 Software Version: SW22B Picture 1: Constituents of the sample Picture 2: EUT Positioning for RF