RAD306HSPA USB MODEM

1 User Manual Table of Contents 1. Safety and Use ........................................................................ 2 2. Installation Guide .................................................................... 3 3. Main Interface Overview ........................................................ 4 4. Connect to Internet ................................................................ 5 5. Statistics .................................................................................. 6 6. Communication ...................................................................... 7 7. Settings ................................................................................. 10 8. Browser ................................................................................. 12 9. Warranty ............................................................................... 12 10. FAQs .................................................................................... 14 11.Certification ......................................................................... 15 2 1. Safety and Use We recommend that you read this chapter carefully before using your modem. The manufacturer disclaims any liability for damage, which may result as a consequence of improper use of the modem or of use contrary to the instructions contained herein. Traffic Safety When driving, do not use the modem:  When switched on, the modem emits electromagnetic waves that can interfere with the vehicle’s electronic systems such as ABS anti‐lock brakes or airbags. To ensure that there is no problem, please do not place the modem on top of the dashboard or within an airbag deployment area.  Check with your car dealer or the car manufacturer to make sure that the dashboard is adequately shielded from modem RF energy. Conditions of Use 1. Switch the modem off before boarding an aircraft. 2. Switch the modem off when you are in health care facilities, except in designated areas. As with many other types of equipment now in regular use, mobile Tele‐modems can interfere with other electrical or electronic devices, or equipment‐using radio frequencies. 3. Switch the modem off when you are near gas or flammable liquids. Strictly obey all signs and instructions posted in a fuel depot, petrol station, chemical plant, or in any potentially explosive atmosphere. 4. When the modem is switched on, it should be kept at least 15 cm from any medical device such as a pacemaker, a hearing aid or insulin pump, etc. 5. Do not let children use the modem without supervision. The modem may contain small parts that could become detached and create a choking hazard. 6. When replacing the cover, please note that the modem may contain substances that could create an allergic reaction. 7. Always handle the modem with care and keep it in a clean and dust‐free place. 8. Do not open, dismantle or attempt to repair the modem yourself. 9. Do not drop, throw or bend the modem. 10. Do not paint the modem. 11. Do not allow the USB‐Modem to be exposed to adverse weather or environmental conditions (moisture, humidity, rain, infiltration of liquids, dust, 3 sea air, etc). The manufacturer’s recommended operating temperature range is ‐25°C to +55°C. Collection Point: This symbol on the modem means that it must be taken to collection points at the end of their life:  Municipal waste disposal centers with specific bins for these items of equipment Collection bins at points of sale.  They will then be recycled, preventing substances being disposed of in the environment, so that their components can be reused. In European Union countries: These collection points are accessible free of charge. All products with this symbol must be brought to these collection points. In non European Union jurisdictions: Items of equipment with this symbol are not to be thrown into ordinary bins if your jurisdiction or your region has suitable recycling and collection facilities; instead they are to be taken to collection points for them to be recycled. In the United States, please visit www.recyclewirelessphones.org for more information on recycling wireless products. Protection against theft The modem is identified by an IMEI (modem serial number) shown on the packaging label and in the modem’s dashboard. We recommend that you note the number the first time you use the modem by opening the dashboard “Settings” > “Diagnostics” to get it. Disclaimer There may be certain differences between the user manual description and the modem’s operation, depending on the software release of the modem or specific operator services. 2. Installation Guide 2.1 Installation Guide for Windows Installation procedures may vary based on the operating system installed on your PC. The following instructions are based on the Windows XP OS: 4 Turn on your PC and plug the modem into the USB interface slot to begin software installation. Windows should automatically detect the new device and will prompt you to begin installation. After following the prompts of installation setup, upon completion, a shortcut will be placed on your desktop for quick future access. Note: 1. If installation “auto‐run” does not begin, you will need to locate the “autoRun.exe)” file in the driver path, and Double‐Click on AutoRun.exe to run the installation manually. 2. A Micro‐SD card is an optional accessory. 3. Please do not remove the USIM/SIM card or the Micro‐SD card when the modem is in use. Upon successful installation of the USB modem program, the program will launch automatically. You may also double‐click the short cut icon on the desktop to launch the program. 2.2 Installation Guide for Mac This manual describes the operations of the connect application. This application requires MAC OS X10.4.9 or 10.7 1. To install the modem connect application on MAC OS X. Please double‐click the file My Connection.pkg 2. Click Continue 3. Select the Partition to install the application and click “Continue Installation” 4. When the installation is fin…

Text truncated - open the document above for the full version.

Date: July 26, 2012 To: Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD 21046 Re: TCT Mobile Limited FCC ID: RAD306 FCC Part 22 & 24 Certification Confidentiality Request Gentlemen: This letter is to comply with 47 CFR 0.457& 0.459 pertaining to confidentiality material. TCT Mobile Limited requests that the following documents regarding this submission for FCC ID: RAD306 be kept confidential: Exhibit Type File Name Block Diagram CONF APPENDIX RAD306_Block Diagram.pdf Schematics CONF APPENDIX RAD306_Schematics.pdf Operational Description CONF APPENDIX RAD306_Operational Description.pdf Part list CONF APPENDIX RAD306_BOM.pdf Tune-Up-Procedure CONF APPENDIX RAD306_Tune up procedure.pdf Those documents contain detailed system and equipment description and related information about the product which TCT Mobile Limited considers to be confidential proprietary, a custom design and , otherwise, not releasable to the general public. Since this design is a basis form which future technological products will evolve, TCT Mobile Limited considers this information would be of benefit to its competitors, and that the disclosure of the information in these documents would give competitors an unfair advantage in the market. Yours Sincerely, Zhizhou Gong Project Manager

Internal Photos

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

SZ12070032S01 Page 2 of 80 DIRECTORY DIRECTORY....................................................................................................................................2 1. TESTING LABORATORY.........................................................................................................4 1.1. Identification of the Responsible Testing Laboratory................................................................. 4 1.2. Identification of the Responsible Testing Location.....................................................................4 1.3. Accreditation Certificate..............................................................................................................4 1.4. List of Test Equipments...............................................................................................................4 2. TECHNICAL INFORMATION..................................................................................................5 2.1. Identification of Applicant...........................................................................................................5 2.2. Identification of Manufacturer.....................................................................................................5 2.3. Equipment Under Test (EUT)......................................................................................................5 2.3.1. Photographs of the EUT............................................................................................................5 2.3.2. Identification of all used EUT...................................................................................................5 2.4. Applied Reference Documents.................................................................................................... 6 2.5. Device Category and SAR Limits................................................................................................6 2.6. Test Environment/Conditions......................................................................................................7 3. SPECIFIC ABSORPTION RATE (SAR)...................................................................................8 3.1. Introduction..................................................................................................................................8 3.2. SAR Definition............................................................................................................................ 8 4. SAR MEASUREMENT SETUP..................................................................................................9 4.1. The Measurement System............................................................................................................9 4.2. Probe............................................................................................................................................ 9 4.3. Phantom..................................................................................................................................... 11 4.4. Device Holder............................................................................................................................11 5. TISSUE SIMULATING LIQUIDS........................................................................................... 12 6. UNCERTAINTY ASSESSMENT............................................................................................. 13 6.1. UNCERTAINTY EVALUATION FOR HANDSET SAR TEST............................................ 13 6.2. UNCERTAINTY FOR SYSTEM PERFORMANCE CHECK................................................ 14 7. SAR MEASUREMENT EVALUATION................................................................................. 16 7.1. System Setup..............................................................................................................................16 7.2. Validation Results......................................................................................................................16 8. OPERATIONAL CONDITIONS DURING TEST..................................................................18 SZ12070032S01 Page 3 of 80 8.1. Body-worn Configurations........................................................................................................ 18 8.2. Measurement procedure.............................................................................................................18 8.3. Description of interpolation/extrapolation scheme....................................................................19 9. 3G MEASUREMENT PROCEDURES....................................................................................19 9.1. Procedures Used To Establish Test Signal................................................................................ 19 9.2. SAR Measurement Conditions for WCDMA............................................................................19 9.3. Output Power Verification.........................................................................................................19 9.4. Measurement Of Conducted Peak Output Power......................................................................20 1. WCDMA Mode............................................................................................................................ 20 10. TEST RESULTS LIST.............................................................................................................22 ANNEX A EUT SETUP PHOTOS................................................................................................24 ANNEX B GRAPH TEST RESULTS...........................................................................................27 Change History IssueDateReason for change 1.0Jul. 26, 2012First edition SZ12070032S01 Page 4 of 80 1. Testing Laboratory 1.1. Identification of the Responsible Testing Laboratory Company Name:Shenzhen Morlab Communications Technology Co., Ltd. Department:Morlab Laboratory Address:3/F, Electronic Testing…

Text truncated - open the document above for the full version.

Report No.: SZ12070032W01 Page 2 of 117 TABLE OF CONTENTS 1. GENERAL INFORMATION .................................................................................................... 3 1.1 EUT Description ......................................................................................................................... 3 1.2 Test Standards and Results ........................................................................................................ 5 1.3 Facilities and Accreditations ...................................................................................................... 6 2. 47 CFR PART 2, PART 22H & 24E REQUIREMENTS ........................................................ 7 2.1 Conducted RF Output Power .................................................................................................... 7 2.2 99% Occupied Bandwidth ....................................................................................................... 19 2.3 Frequency Stability ................................................................................................................... 29 2.4 Conducted Out of Band Emissions ......................................................................................... 35 2.5 Band Edge ................................................................................................................................. 67 2.6 Transmitter Radiated Power (EIRP/ERP) ............................................................................. 79 2.7 Radiated Out of Band Emissions ............................................................................................ 86 Change History Issue Date Reason for change 1.0 Jul 25, 2012 First edition Report No.: SZ12070032W01 Page 3 of 117 1. GENERAL INFORMATION 1.1 EUT Description EUT Type ............................. : HSPA USB Modem Serial No. .............................. : (n.a, marked #1 by test site) Hardware Version ................. : PIO Software Version .................. : Applicant .............................. : Manufacturer ........................ : S1_B15001S_1110000_B10001S TCT Mobile Limited Address: 5F, E building, No. 232, Liang Jing Road ZhangJiang High-Tech Park, Pudong Area Shanghai, P.R. China. 201203 TCL COMMUNICATION TECHNOLOGY HOLDINGS LIMITED 70 Huifeng 4rd,ZhongKai Hi-tech Development District , Huizhou, Guangdong 516006 P.R.China （TCL Mobile Communication Co.,LTD.Huizhou） Frequency Range .................. : GSM 850MHz: Tx: 824.20 - 848.80MHz (at intervals of 200kHz); Rx: 869.20 - 893.80MHz (at intervals of 200kHz) GSM 1900MHz: Tx: 1850.20 - 1909.80MHz (at intervals of 200kHz); Rx: 1930.20 - 1989.80MHz (at intervals of 200kHz) WCDMA 850MHz Tx: 826.4 - 846.6MHz (at intervals of 200kHz); Rx: 871.4 - 891.6MHz (at intervals of 200kHz) WCDMA 1900MHz Tx: 1852.4 - 1907.6MHz (at intervals of 200kHz); Rx: 1932.4 - 1987.6MHz (at intervals of 200kHz) Modulation Type................... : GPRS/GSM Mode with GMSK Modulation EDGE Mode with 8PSK Modulation WCDMA Mode with QPSK Modulation HSDPA Mode with QPSK Modulation HSUPA Mode with QPSK Modulation Multislot Class ...................... : GPRS: Multislot Class12,EGPRS: Multislot Class12 Antenna Type ........................ : PIFA Antenna Emission Designators ........... : GSM:255KGXW, EGPRS:249KG7W, WCDMA:4M11F9W Note 1: The transmitter (Tx) frequency arrangement of the Cellular 850MHz band used by the EUT can be represented with the formula F(n)=824.2+0.2*(n-128), 128<=n<=251; the lowest, middle, highest channel numbers (ARFCHs) used and tested in this report are separately 128 Report No.: SZ12070032W01 Page 4 of 117 (824.2MHz), 190 (836.6MHz) and 251 (848.8MHz). Note 2: The transmitter (Tx) frequency arrangement of the PCS 1900MHz band used by the EUT can be represented with the formula F(n)=1850.2+0.2*(n-512), 512<=n<=810; the lowest, middle and highest channel numbers (ARFCHs) used and tested in this report are separately 512 (1850.2MHz), 661 (1880.0MHz) and 810 (1909.8MHz). Note 3: The transmitter (Tx) frequency arrangement of the WCDMA 850MHz band used by the EUT can be represented with the formula F(n)=826.4+0.2*(n-4132), 4132<=n<=4233; the lowest, middle and highest channel numbers (ARFCHs) used and tested in this report are separately 4132 (826.4MHz), 4175(835MHz) and 4233 (846.6MHz). Note 4: The transmitter (Tx) frequency arrangement of the WCDMA 1900MHz band used by the EUT can be represented with the formula F(n)=1852.4+0.2*(n-9262), 9262<=n<=9538; the lowest, middle and highest channel numbers (ARFCHs) used and tested in this report are separately 9262 (1852.4MHz), 9400 (1880MHz) and 9538 (1907.6MHz). Note 5: For a more detailed description, please refer to Specification or User’s Manual supplied by the applicant and/or manufacturer. Report No.: SZ12070032W01 Page 5 of 117 1.2 Test Standards and Results The objective of the report is to perform testing according to 47 CFR Part 2, Part 22 and Part 24 for the EUT FCC ID Certification: No. Identity Document Title 1 47 CFR Part 2 (10-1-09 Edition) Frequency Allocations and Radio Treaty Matters; General Rules and Regulations 2 47 CFR Part 22 (10-1-09 Edition) Public Mobile Services 3 47 CFR Part 24 (10-1-09 Edition) Personal Communications Services Test detailed items/section required by FCC rules and results are as below: No. Section Description Result 1 2.1046 Conducted RF Output Power PASS 2 2.1049 99% Occupied Bandwidth PASS 3 2.1055 22.355 24.235 Frequency Stability PASS 4 2.1051 2.1057 22.917 24.238 Conducted Out of Band Emissions PASS 5 2.1051 2.1057 22.917 24.238 Band Edge PASS 6 22.913 24.232 Transmitter Radiated Power (EIPR/ERP) PASS 7 2.1053 2.1057 22.917 24.238 Radiated Out of Band Emissions PASS NOTE：Measurement method according to TIA/EIA 603.D-2010 Report No.: SZ12070032W01 Page 6 of 117 1.3 Facilities and Accreditations 1.3.1 Facilities Shenzhen Morlab Communications Technology Co., Ltd. Morlab Laboratory is a testing organization accredited by Chi…

Text truncated - open the document above for the full version.

Test Setup Photos 1. CSE 2. RSE