RAD387HSPA + USB Dongle

1 User Manual 2 Safety Precautions Read the safety precautions carefully to ensure the correct and safe use of your wireless device. Do not switch on your device when the device use is prohibited or when the device use may cause interference or danger. Follow the rules or regulations in hospitals and health care facilities. Switch off your device near medical apparatus. Switch off your device in an aircraft. The device may cause interference to control signals of the aircraft. Switch off your device near high-precision electronic devices. The device may affect the performance of these devices. Do not attempt to disassemble your device or its accessories. Only qualified personnel are allowed to service or repair the device. Do not place your device or its accessories in containers with strong electromagnetic field. Do not place magnetic storage media near your device. Radiation from the device may erase the information stored on them. Do not put your device in a high-temperature place or use it in a place with flammable gas such as a gas station. Keep your device and its accessories away from children. Do not allow children to use your device without guidance. Observe the laws or regulations on device use. Respect others’ privacy and legal rights when using your device. It is recommended that the equipment only be used in the environment where temperature is between -10 and °C50 and humidity is between 10% to 90%. Keep °C the equipment in the environment where temperature is between -10 and 70 or °C°C humidity is between 10% to 90%. 3 Content Safety Precautions .................................................................................................... 2 1. Overview ................................................................................................................ 4 2. Web UI configuration ............................................................................................ 4 3. Connection ............................................................................................................ 4 4. SMS ........................................................................................................................ 5 5. Settings .................................................................................................................. 6 5.1 Network ................................................................................................................ 6 5.2 PIN Code Management ....................................................................................... 6 5.3 Connection Profile .............................................................................................. 7 5.4 Connection Mode ................................................................................................ 7 5.5 Language ............................................................................................................. 8 5.6 System ................................................................................................................. 8 6. Warranty ................................................................................................................. 8 7. FAQs....................................................................................................................... 9 8. Certification ......................................................................................................... 11 4 1. Overview Welcome to choose our mobile broadband device. This device allows you to connect to internet from anywhere, anytime. To use this device you need a device with web browser. 2. Web UI configuration Open the browser, and then input the address http://192.168.1.1. The page is displayed as bellow: Fig 2 3. Connection Current status  Active profile: Select the profile you want to use from the drop down box.  Connection Status: display the network is connected or disconnected;  Usage: Display usage data  Duration: the duration for current connection; WAN status  Network name: the network name you are using; 5  Network type: GPRS/EDGE/UMTS/HSDPA/HSUPA/HSPA+  Roaming: display whether you are in roaming network or not;  IP address: this is the IP address arranged for this device. Usage History Click link of Usage History, will display current data and total data of usage.  Usage: Display usage data  Upload: Display upload usage data  Download: Display download usage data  Duration: Display duration time 4. SMS You can move the mouse to "SMS" and click the items you want. In this section, the following items are included:  Inbox: list the SMS received;  Sent: list the SMS sent successfully.  Draft: save the SMS not sent or sent failed.  SMS settings: set the SMS center number and the SMS saved location ; Read SMS: Click the content of the SMS to read; Write SMS 1,Click “New Message” to create a new SMS on “Inbox/Sent/Draft”; 2,Input the number and the content; 3,Click <Sent>; Forward SMS 1,Click the content of the SMS you want to forward; 2,Click <Forward>; 3,Input the number; 4,Click <Sent>; Reply SMS 1,Click the content of the SMS you want to reply; 2,Click <Reply>; 3,Input the content; 4,Click <Sent>; Delete SMS 1,Click the Mark of the SMS you want to delete; 6 2,Click <Delete>; Delete all SMS 1,Click <Mark All> icon on top of SMS list; 2, Click <Delete>; SMS settings SMS Center Number: You can get it from your operator; SMS Save Mode: the location SMS stored, default is SIM card; 5. Settings You can move the mouse to "Settings" and click the items you want. In this section, the following items are included:  Network: set network mode;  PIN Code Management: Enable/Disable/Change PIN code;  Connection Profile: set connection profile;  Connection Mode: set connection mode in Auto or Manual;  Language: set the language displayed on the web UI  System: display the device info, save & restore the configuration; 5.1 Network Network Mode: Automatic /3G only/2G only, default is automatic Network Sele…

Text truncated - open the document above for the full version.

Date: 22 April, 2013 To: Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD 21046 Re: TCT Mobile Limited FCC ID: RAD387 FCC Part 22 Certification FCC Part 24 Certification Confidentiality Request Gentlemen: This letter is to comply with 47 CFR 0.457 and 0.459 pertaining to confidentiality material.TCT Mobile Limited requests that the following documents regarding this submission for FCC ID: RAD387 be kept confidential: Exhibit Type File Name Block Diagram CONF APPENDIX RAD387_Block Diagram.pdf Schematics CONF APPENDIX RAD387 _Schematics.pdf Operational Description CONF APPENDIX RAD387 _Operational Description.pdf Part list CONF APPENDIX RAD387 _BOM.pdf Tune-Up-Procedure CONF APPENDIXRAD387 _Tune up procedure.pdf Those documents contain detailed system and equipment description and related information about the product which TCT Mobile Limited considers to be confidential proprietary, a custom design and, otherwise, not releasable to the general public. Since this design is a basis form which future technological products will evolve, TCT Mobile Limited considers this information would be of benefit to its competitors, and that the disclosure of the information in these documents would give competitors an unfair advantage in the market. Signatory Gong ZhiZhou TCT Mobile Limited

External Photos 1. EUT front view 2. EUT rear view 3. EUT left side view 4. EUT right side view 5. EUT top view 6. EUT bottom view

FCC ID: RAD387 Label Size: 48*15mm Label Location FCC ID LABEL Location

Internal Photos 1. EUT uncover view 2. Mainboard front view without shielding 3. Mainboard rear view without shielding 4. GSM/WCDMA chip view 5. CPU chip view 6. GSM/WCDMA antenna view

4/F, South Building,No.2966, Jinke Road, Zhangjiang High-Tech Park, Pudong, Shanghai, 201203, P.R.China, TEL: +86(0)21 61460666 FAX: +86(0)21 61460600 Tune-up Procedure of Alcatel One Touch X500Y During manufacturing each WWAN USB Adaptor will be individually calibrated. The measurement is done in a fully calibrated setup, which is based on Agilent 8960 or R/S CMU200 (TX power, AFC, DRP, LNA Gain.....). Furthermore, the highest power level is verified afterwards in a call measurement on three channels (low, mid and high). Procedure: 1. Set the Data Card to operational voltage and on one certain channel in a special service mode by means of company proprietary software. 2. The actual power is measured at several power levels. 3. The gain factors of each individual Data Card are adjusted via the Board- test SW using automatic adjustment arithmetic until the target value is met. The appropriate gain control settings are stored in RF table (a special section in Nor Flash marked with Read only and untouchable for end user) each phone individually (for each power level). 4/F, South Building,No.2966, Jinke Road, Zhangjiang High-Tech Park, Pudong, Shanghai, 201203, P.R.China, TEL: +86(0)21 61460666 FAX: +86(0)21 61460600 Output Power level tolerance: Band Tune-up power tolerance (dBm) GSM850 PCL = 5, PWR =33.5+-0.5 GSM1900 PCL=0,PWR= 29+-0.5 GPRS 850 PCL = 5, PWR =33.5+-0.5(1 slots) PCL = 5, PWR =29.5+-0.5(2 slots) PCL = 5, PWR =28.5+-0.5(3 slots) PCL = 5, PWR =27.5+-0.5(4 slots) EDGE 850 PCL = 5, PWR =33.5+-0.5(1 slots) PCL = 5, PWR =29.5+-0.5(2 slots) PCL = 5, PWR =28+-0.5(3 slots) PCL = 5, PWR =27.5+-0.5(4 slots) GPRS 1900 PCL=0,PWR= 29+-0.5(1 slots) PCL=0,PWR= 26.5+-0.5(2 slots) PCL=0,PWR= 24.5+-0.5(3 slots) PCL=0,PWR= 23.5+-0.5(4 slots) EDGE 1900 PCL=0, PWR=29+-0.5(1 slots) PCL=0,PWR= 26+-0.5(2 slots) PCL=0,PWR= 24.5+-0.5(3 slots) PCL=0,PWR= 23.5+-0.5(4 slots) WCDMA 850 Max output power =22(+1/-2) WCDMA 1900 Max output power =23(+1/-2) TCl Mobile Limited

Report No.: SZ13040169E01 Page 2 of 16 TABLE OF CONTENTS 1. GENERAL INFORMATION .................................................................................................... 3 1.1 EUT Description ......................................................................................................................... 3 1.2 Test Standards and Results ........................................................................................................ 4 1.3 Facilities and Accreditations ...................................................................................................... 5 1.3.1 Facilities .................................................................................................................................... 5 1.3.2 Test Environment Conditions .................................................................................................... 5 1.3.3 Measurement Uncertainty ......................................................................................................... 5 2. TEST CONDITIONS SETTING............................................................................................... 6 2.1 Test Mode .................................................................................................................................... 6 2.2 Test Setup and Equipments List ................................................................................................ 7 2.2.1 Conducted Emission.................................................................................................................. 7 2.2.2 Radiated Emission ..................................................................................................................... 8 3. 47 CFR PART 15B REQUIREMENTS .................................................................................. 11 3.1 Conducted Emission ................................................................................................................. 11 3.1.1 Requirement ............................................................................................................................ 11 3.1.2 Test Description ...................................................................................................................... 11 3.1.3 Test Result ............................................................................................................................... 11 3.2 Radiated Emission .................................................................................................................... 13 3.2.1 Requirement ............................................................................................................................ 13 3.2.2 Test Description ...................................................................................................................... 13 3.2.3 Frequency range of measurement ........................................................................................... 13 3.2.4 Test Result ............................................................................................................................... 14 Change History Issue Date Reason for change 1.0 May 24, 2013 First edition Report No.: SZ13040169E01 Page 3 of 16 1. GENERAL INFORMATION 1.1 EUT Description EUT Type ........................HSPA+ USB DONGLE Serial No. ........................(n.a., marked #1 by test site) Hardware Version. ......... .V2.0 Software Version .............S1_B15001S_1110000_B10001S Applicant ......................... Manufacturer ................... Nominal Voltage ............. TCT Mobile Limited 5F, C building, No. 232, Liang Jing Road Zhang Jiang High-Tech Park, Pudong Area Shanghai, P.R. China. 201203 TCL COMMUNICATION TECHNOLOGY HOLDINGS LIMITED 70 Huifeng 4rd, ZhongKai Hi-tech Development District, Huizhou, Guangdong 516006 P.R. China 5.0V DC Speed of the processor ... .450MHz (generated by the CPU) 32.768KHz (generated by the crystal oscillator) Note 1: The EUT is a HSPA+ USB DONGLE, it supports GSM 850MHz, 900MHz, 1800MHz, 1900MHz, GPRS, EDGE, WCDMA BandV, BandII, HSDPA, HSUPA, HSPA+. Note 2: The EUT was connected with a PC while testing. Note 3: Please refer to Annex A for the photographs of the EUT. For a more detailed description, please refer to Specification or User’s Manual supplied by the applicant and/or manufacturer. Report No.: SZ13040169E01 Page 4 of 16 1.2 Test Standards and Results The objective of the report is to perform testing according to 47 CFR Part 15 Subpart B: No. Identity Document Title 1 47 CFR Part 15 Radio Frequency Devices Test detailed items/section required by FCC rules and results are as below: No. Section Description Result 1 15.107 Conducted Emission PASS 2 15.109 Radiated Emission PASS NOTE: The tests were performed according to the method of measurements prescribed in ANSI C63.4 2009. Report No.: SZ13040169E01 Page 5 of 16 1.3 Facilities and Accreditations 1.3.1 Facilities Shenzhen Morlab Communications Technology Co., Ltd. Morlab Laboratory is a testing organization accredited by China National Accreditation Service for Conformity Assessment (CNAS) according to ISO/IEC 17025. The accreditation certificate number is L3572. All measurement facilities used to collect the measurement data are located at FL.3, Building A, FeiYang Science Park, No.8 LongChang Road, Block 67, BaoAn District, ShenZhen, GuangDong Province, P. R. China 518101. The test site is constructed in conformance with the requirements of ANSI C63.4(2009) and CISPR Publication 22(2010); the FCC registration number is 695796. 1.3.2 Test Environment Conditions During the measurement, the environmental conditions were within the listed ranges: Temperature (°C): 15 - 35 Relative Humidity (%): 30 - 60 Atmospheric Pressure (kPa): 86 -106 1.3.3 Measurement Uncertainty The uncertainty is calculated using the methods suggested in the "Guide to the Expression of Uncertainty in Measurement" (GUM) published by ISO. Uncertainty of Conducted E…

Text truncated - open the document above for the full version.

Test Setup Photos 1. Conducted emission main’s port front view 2. Conducted emission main’s port side view 3. Radiated emission front view 4. Radiated emission rear view