RGPCAPRBluetooth Wireless Headset

User Guide -REV D 22.07.04 English Neo-507 Bluetooth® Wireless Headset Index 1. Introduction.......................................... 2. First steps.............................................. Charging.................................... Pairing....................................... 3. Wearing the Headset.............................. 4. General Usage........................................ 5. Resetting your Headset.......................... 6. Advanced Features in Hands-free mode 7. Troubleshooting.................................... 8. Additional Information.......................... 9. Declaration of Conformity..................... 10. Commands Summary Table................. Note: Please read the “Safe usage guidelines” on page 14 and “Limited Warranty” on page 16 before using the Headset. 1. Introduction Thank you for choosing to buy a Bluetooth (*) SouthWing Headset. We hope you enjoy using it as much as we did developing it. This User Guide provides all the information you will need on how to use and look after your product. As a Bluetooth mobile phone will most commonly be used with your Bluetooth Headset, references to a mobile phone are used throughout this User Guide. * Bluetooth is a registered trademark owned by Bluetooth SIG, Inc. U.S.A. and licensed to SouthWing. SouthWing SouthWing is headquartered in Barcelona, Spain. Our experienced team is focused on developing the future generation of wireless headsets. Should you wish to learn more about the company, please visit our web site at: www.south-wing.com If you have any comments or suggestions on this or any other SouthWing product, we would love to hear from you. Overview—Headset 2. First Steps When you first receive your SouthWing Bluetooth Wireless Headset you will need to charge the battery and pair the Headset to your mobile phone. Charging (Fig. 2: Charging) Your Bluetooth Headset has an internal rechargeable battery and USB Charging Socket. To charge this battery, you can follow any of these steps: Mains charging Step 1. Always first plug the connector of the power supply into the USB Charging socket [6] (Fig. 1. Overview- Headset), with the arrow facing down (Drawing B), that is, never with the arrow facing up (Drawing A). Make sure that the connector enters smoothly. Step 2. Plug the power supply into the mains. Step 3. The Headset Indicator Light will turn green to indicate the Headset battery is charging. Step 4. Once the Headset Indicator Light turns off, the Headset is fully charged and can be removed from the power supply. USB charging Thanks to its USB charging facility, the Headset battery can be charged from any USB port, such as those found on a PC or laptop, by using the SouthWing USB cable adaptor accessory. In-car charging You can charge the Headset battery in your vehicle. To do so, check that the vehicle plug is 12V-24V compatible and use only the SouthWing USB car charger accessory (which includes the USB cable adaptor accessory). Please Note: • The Headset will not function while charging. • If the Headset Indicator Light [2] remains off when charging, the battery is already fully charged and does not require further charging. • To maximise battery life, do not charge the Headset for extended periods of time. • Full battery capacity will be achieved after two or three full charge/discharge cycles. • When your battery is flat, it takes up to four hours to completely charge your headset • Only use SouthWing power supply or accessories for charging Pairing Before using your Headset you will need to pair it to your Bluetooth mobile phone. You will need to repeat this process if you want to use your Headset with another mobile phone. Pairing is a feature of your Bluetooth Headset that prevents anyone else eavesdropping on your phone conversations. This product supports both the Headset and Hands-free profiles, which ensures compatibility with a larger number of Bluetooth mobile phone models. 1. Ensure the Headset is off (see below on how to turn your headset on and off) and that the mobile phone with which you wish to pair is not too far apart (less than 1 meter of separation will ensure most reliable pairing). 2. Put the mobile phone into pairing mode (see the instructions which came with your phone). 3. Press and hold the Multi-function Dial [1] for about 5 seconds until the Headset Indicator Light [2] alternates between red and green (you will also hear a series of high tones). Now the Headset is ready for pairing in Headset mode. 4. If your mobile phone supports the Hands-free mode, just briefly push once again the Multi-function Dial and the Headset will attempt pairing in Hands-free mode (you will hear a series of low tones). Briefly pushing the button will allow you to alternate between Headset and Hands-free modes. You now need to wait several seconds while both devices attempt to pair. 5. Follow the menus on your mobile phone to finalise the pairing process. If you are asked for a PIN number, note that the default PIN number for the SouthWing Bluetooth Headset is 1111. Please Note: • If pairing is successful, the Headset Indicator Light [2] will begin flashing green. You can now start using your Headset. • If you choose to do the pairing in Hands-free mode, you will be able to access a wider range of headset functions (see section ‘Advanced features in hands-free mode`’) 3. Wearing the Headset (Fig. 3: Wearing the Headset) You will find it is easy to place the Headset on your ear (even with just one hand). These directions will help and over time you will find your own way of wearing the Headset. Placing the Headset on your ear 1. Place the tip of the ear hook right behind your ear 2. Rotate the headset to make the ear hook slide behind your ear 3. Gently place the speaker over or slightly into your ear canal 4. Finally find the most comfortable position by rotating the Headset forward and backward Adjusting the ear hook The ear hook can be bent for optimum comfort. You can look for the best…

Text truncated - open the document above for the full version.

FCC Statements (Federal Communications Commission, USA) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. To identify this product, refer to the Part, Series, or Model number found on the product. The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by SouthWing may void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio or television technician for help. This product emits radio frequency energy, but the radiated output power of this device is far below the FCC radio frequency exposure limits. Nevertheless, the device should be used in such a manner that the potential for human contact with the antenna during normal operation is minimized.

User Guide -REV D 22.07.04 English Neo-507 Bluetooth® Wireless Headset Index 1. Introduction.......................................... 2. First steps.............................................. Charging.................................... Pairing....................................... 3. Wearing the Headset.............................. 4. General Usage........................................ 5. Resetting your Headset.......................... 6. Advanced Features in Hands-free mode 7. Troubleshooting.................................... 8. Additional Information.......................... 9. Declaration of Conformity..................... 10. Commands Summary Table................. Note: Please read the “Safe usage guidelines” on page 14 and “Limited Warranty” on page 16 before using the Headset. 1. Introduction Thank you for choosing to buy a Bluetooth (*) SouthWing Headset. We hope you enjoy using it as much as we did developing it. This User Guide provides all the information you will need on how to use and look after your product. As a Bluetooth mobile phone will most commonly be used with your Bluetooth Headset, references to a mobile phone are used throughout this User Guide. * Bluetooth is a registered trademark owned by Bluetooth SIG, Inc. U.S.A. and licensed to SouthWing. SouthWing SouthWing is headquartered in Barcelona, Spain. Our experienced team is focused on developing the future generation of wireless headsets. Should you wish to learn more about the company, please visit our web site at: www.south-wing.com If you have any comments or suggestions on this or any other SouthWing product, we would love to hear from you. Overview—Headset 2. First Steps When you first receive your SouthWing Bluetooth Wireless Headset you will need to charge the battery and pair the Headset to your mobile phone. Charging (Fig. 2: Charging) Your Bluetooth Headset has an internal rechargeable battery and USB Charging Socket. To charge this battery, you can follow any of these steps: Mains charging Step 1. Always first plug the connector of the power supply into the USB Charging socket [6] (Fig. 1. Overview- Headset), with the arrow facing down (Drawing B), that is, never with the arrow facing up (Drawing A). Make sure that the connector enters smoothly. Step 2. Plug the power supply into the mains. Step 3. The Headset Indicator Light will turn green to indicate the Headset battery is charging. Step 4. Once the Headset Indicator Light turns off, the Headset is fully charged and can be removed from the power supply. USB charging Thanks to its USB charging facility, the Headset battery can be charged from any USB port, such as those found on a PC or laptop, by using the SouthWing USB cable adaptor accessory. In-car charging You can charge the Headset battery in your vehicle. To do so, check that the vehicle plug is 12V-24V compatible and use only the SouthWing USB car charger accessory (which includes the USB cable adaptor accessory). Please Note: • The Headset will not function while charging. • If the Headset Indicator Light [2] remains off when charging, the battery is already fully charged and does not require further charging. • To maximise battery life, do not charge the Headset for extended periods of time. • Full battery capacity will be achieved after two or three full charge/discharge cycles. • When your battery is flat, it takes up to four hours to completely charge your headset • Only use SouthWing power supply or accessories for charging Pairing Before using your Headset you will need to pair it to your Bluetooth mobile phone. You will need to repeat this process if you want to use your Headset with another mobile phone. Pairing is a feature of your Bluetooth Headset that prevents anyone else eavesdropping on your phone conversations. This product supports both the Headset and Hands-free profiles, which ensures compatibility with a larger number of Bluetooth mobile phone models. 1. Ensure the Headset is off (see below on how to turn your headset on and off) and that the mobile phone with which you wish to pair is not too far apart (less than 1 meter of separation will ensure most reliable pairing). 2. Put the mobile phone into pairing mode (see the instructions which came with your phone). 3. Press and hold the Multi-function Dial [1] for about 5 seconds until the Headset Indicator Light [2] alternates between red and green (you will also hear a series of high tones). Now the Headset is ready for pairing in Headset mode. 4. If your mobile phone supports the Hands-free mode, just briefly push once again the Multi-function Dial and the Headset will attempt pairing in Hands-free mode (you will hear a series of low tones). Briefly pushing the button will allow you to alternate between Headset and Hands-free modes. You now need to wait several seconds while both devices attempt to pair. 5. Follow the menus on your mobile phone to finalise the pairing process. If you are asked for a PIN number, note that the default PIN number for the SouthWing Bluetooth Headset is 1111. Please Note: • If pairing is successful, the Headset Indicator Light [2] will begin flashing green. You can now start using your Headset. • If you choose to do the pairing in Hands-free mode, you will be able to access a wider range of headset functions (see section ‘Advanced features in hands-free mode`’) 3. Wearing the Headset (Fig. 3: Wearing the Headset) You will find it is easy to place the Headset on your ear (even with just one hand). These directions will help and over time you will find your own way of wearing the Headset. Placing the Headset on your ear 1. Place the tip of the ear hook right behind your ear 2. Rotate the headset to make the ear hook slide behind your ear 3. Gently place the speaker over or slightly into your ear canal 4. Finally find the most comfortable position by rotating the Headset forward and backward Adjusting the ear hook The ear hook can be bent for optimum comfort. You can look for the best…

Text truncated - open the document above for the full version.

FCC Statements (Federal Communications Commission, USA) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. To identify this product, refer to the Part, Series, or Model number found on the product. The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by SouthWing may void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio or television technician for help. This product emits radio frequency energy, but the radiated output power of this device is far below the FCC radio frequency exposure limits. Nevertheless, the device should be used in such a manner that the potential for human contact with the antenna during normal operation is minimized.

15.247 (a) (1) Statement CETECOM S.A. – ITA team Page 1 of 1 Bluetooth devices 15.247 (a) (1) Statement Bluetooth devices Date: 27/01/2003 15.247 (a) (1) Statement CETECOM S.A. – ITA team Page 2 of 2 Bluetooth devices 1. Pseudorandom hop selection The generation of the hopping sequence in connection mode depends essentially on two input values: 1. LAP/UAP of the master of the connection 2. Internal master clock The LAP (lower address part) are the 24 LSB’s of the 48 BD_ADDRESS. The BD_ADDRESS is an unambiguous number of every Bluetooth unit. The UAP (upper address part) are the 24 MSB’s of the 48 BD_ADDRESS. The internal clock of a Bluetooth unit is derived from a free running clock which is never adjusted and is never turned off. For synchronisation with other units only offset are used. It has no relation to the time of the day. Its resolution is at least half the RX/TX slot length of 312.5 μs. The clock has a cycle of about one day (23h 30’). In most case it is implemented as 28 bit counter. For the deriving of the hopping sequence the entire LAP (24 bits), 4 LSB’s (4 bits) (Input 1) and the 27 MSB’s of the clock (Input 2) are used. With this input values different mathematical procedures (permutations, additions, XOR-operations) are performed to generate the sequence. This will be done at the beginning of every new transmission. The output constitutes a pseudorandom sequence covering 79 hop channels. The exact procedures for the generation of the pseudorandom hopping sequence can be found in “Bluetooth specification Version 1.1 – Part B – Baseband Specification – Chapter 11: Hop selection”. The following is a sample of a pseudorandom hopping sequence of 20 sec. 32000 hops): 34 72 31 69 28 66 25 63 22 60 19 57 16 54 13 51 10 48 07 45 04 42 01 39 77 36 74 33 71 30 68 27 65 24 62 21 59 18 12 20 09 17 61 20 58 17 00 08 76 05 49 08 46 05 67 75 64 72 37 75 34 72 55 63 52 60 25 63 22 60 43 51 40 48 13 51 10 48 31 39 28 36 01 39 77 36 19 27 16 24 68 27 65 24 70 29 55 14 64 23 49 08 58 17 43 02 52 11 37 75 34 72 43 02 28 66 37 75 20 09 17 06 14 03 11 00 22 60 07 45 16 54 01 39 76 65 73 62 70 59 67 56 78 37 63 22 72 31 57 16 66 25 51 10 60 19 45 04 42 01 51 10 36 74 45 04 28 17 25 14 22 11 19 08 30 68 15 53 24 62 09 47 18 56 03 41 12 50 76 35 73 32 03 41 67 26 76 35 59 48 56 45 53 42 50 39 61 20 46 05 55 14 40 78 49 08 34 72 43 02 28 66 25 63 34 72 19 57 28 66 52 62 49 59 46 56 43 53 40 50 37 47 34 44 31 41 28 38 25 35 22 32 19 29 12 50 09 47 61 48 58 45 77 08 09 19 47 06 58 17 67 26 64 23 37 24 34 21 53 63 64 74 23 61 34 72 31 69 14 52 49 59 32 42 19 57 02 40 37 47 20 30 72 31 04 42 11 21 22 32 62 49 59 46 01 39 77 36 58 45 41 28 52 39 35 22 59 69 56 66 29 67 26 64 47 57 44 54 17 55 14 52 35 45 32 42 05 43 02 40 23 33 20 30 72 31 69 28 11 21 08 18 60 19 57 16 78 09 75 06 48 07 45 04 66 76 63 73 36 74 33 71 38 76 21 59 32 70 15 53 26 64 09 47 20 58 03 41 00 38 11 49 73 32 05 43 69 56 66 53 63 50 60 47 69 28 52 11 63 22 46 05 78 37 75 34 44 33 41 30 72 01 77 06 38 76 43 02 60 68 65 73 26 64 31 69 56 64 45 53 22 60 11 49 30 68 27 65 75 64 72 61 24 32 29 37 69 28 74 33 12 20 17 25 57 16 62 21 63 22 60 19 57 16 54 13 37 26 42 31 31 20 36 25 39 77 36 74 33 71 30 68 13 02 18 07 07 75 12 01 15 53 12 50 09 47 06 44 14 52 11 49 59 48 56 45 08 16 13 21 53 12 58 17 75 04 01 09 41 00 46 05 71 00 60 68 37 75 26 64 45 04 42 01 11 00 08 76 39 47 44 52 05 43 10 48 27 35 32 40 72 31 77 36 78 37 75 34 72 31 69 28 52 41 57 46 46 35 51 40 54 13 51 10 48 07 45 04 28 17 33 22 22 11 27 16 30 68 27 65 24 62 21 59 35 73 32 70 29 67 26 64 27 37 32 42 21 31 26 36 15 25 20 30 09 19 14 24 13 51 02 40 56 43 45 32 01 39 69 28 44 31 33 20 60 19 65 24 24 11 29 16 60 70 57 67 24 62 21 59 18 56 15 53 42 52 39 49 73 60 78 65 18 56 23 61 73 32 70 29 18 28 15 25 49 36 54 41 73 32 78 37 51 38 48 35 45 32 42 29 14 52 11 49 38 48 35 45 02 40 78 37 26 36 23 33 69 28 66 25 14 24 11 21 59 46 56 43 53 40 50 37 59 18 48 07 53 12 42 01 35 22 32 19 29 16 26 13 35 73 24 62 29 67 18 56 09 47 06 44 33 43 30 40 76 35 73 32 21 31 18 28 64 23 61 20 09 19 06 16 52 11 49 08 76 07 73 04 42 29 39 26 36 23 33 20 77 06 66 74 43 02 32 70 57 65 62 70 23 61 28 66 39 77 36 74 05 73 02 70 41 49 30 38 07 45 75 34 29 37 15.247 (a) (1) Statement CETECOM S.A. – ITA team Page 3 of 3 Bluetooth devices 18 26 74 33 63 22 09 17 14 22 54 13 59 18 70 29 67 26 36 25 33 22 72 01 61 69 38 76 27 65 60 68 49 57 26 64 15 53 40 48 45 53 06 44 11 49 22 60 19 57 67 56 64 53 24 32 13 21 69 28 58 17 50 39 47 36 72 31 69 28 52 11 41 00 74 03 63 71 40 78 29 67 62 70 51 59 18 07 23 12 12 01 17 06 06 74 11 00 00 68 05 73 02 70 70 59 75 64 64 53 75 34 72 31 69 28 66 25 51 10 56 15 73 02 78 07 33 22 30 19 55 14 52 11 35 73 24 62 57 65 46 54 23 61 12 50 45 53 34 42 01 69 06 74 74 63 00 68 32 42 19 27 71 30 68 27 10 18 07 15 59 18 56 15 77 06 74 03 47 06 44 03 65 73 62 70 35 73 32 70 53 61 50 58 23 61 20 58 59 18 56 15 53 12 50 09 47 06 44 03 41 00 38 76 35 73 32 70 29 67 26 64 23 61 20 58 17 55 14 52 11 49 08 46 05 43 02 40 78 37 75 34 72 31 69 28 66 25 63 22 60 19 57 16 54 13 51 10 48 07 45 04 42 01 39 77 36 74 33 71 30 68 27 65 24 62 21 59 18 56 15 53 12 50 09 47 06 44 03 41 00 38 76 35 47 34 30 17 41 28 24 11 33 71 30 68 27 65 24 62 23 10 06 72 17 04 00 66 09 47 06 44 03 41 00 38 78 65 61 48 72 59 55 42 64 23 61 20 58 17 55 14 54 41 37 24 48 35 31 18 56 66 67 77 26 64 37 75 46 05 43 02 16 03 13 00 46 56 29 39 16 54 78 37 34 44 17 27 04 42 66 25 08 18 19 29 57 16 68 27 20 58 17 55 38 48 35 45 08 46 05 43 26 36 23 33 75 34 72 31 14 24 11 21 59 46 56 43 53 40 50 37 45 04 56 15 39 77 50 09 35 22 32 19 29 16 26 13 21 59 32 70 15 53 26 64 15 53 12 50 33 43 30 40 03 41 00 38 21 31 18 28 70 29 67 26 09 19 06 16 58 17 55 14 76 07 73 04 42 29 39 26 36 23 33 20 20 28 25 33 65 24 70 29 16 24 05 13 61 20 50 09 69 28 66 25 35 24 32 21 63 71 68 76 29 67 34 72 51 59 56 64 17 55 22 60 47 55 36 44 13 51 02 40 21 59 18 56 66 55 63 52 15 23 20 28 60 19 65 24 03 11 08 16 48 07 53 12 78 07 67 75 44 03 33…

Text truncated - open the document above for the full version.

15.247 (g) Statement CETECOM S.A. – ITA team Page 1 of 1 Bluetooth devices 15.247 (g) Statement – Bluetooth devices Date: 27/01/2003 According to Bluetooth specifications the channel hopping sequence which has a very long period length (23h 30’) does not show repetitive patterns over a short time interval, but distributes the hop frequencies equally over the 79 hopping channels during a short time interval. The generation of the hopping sequence in connection mode depends essentially on two input values: 1. LAP/UAP of the master of the connection 2. Internal master clock The LAP (lower address part) are the 24 LSB’s of the 48 BD_ADDRESS. The BD_ADDRESS is an unambiguous number of every Bluetooth unit. The UAP (upper address part) are the 24 MSB’s of the 48 BD_ADDRESS. The internal clock of a Bluetooth unit is derived from a free running clock which is never adjusted and is never turned off. For synchronisation with other units only offset are used. It has no relation to the time of the day. Its resolution is at least half the RX/TX slot length of 312.5 μs. The clock has a cycle of about one day (23h 30’). In most case it is implemented as 28 bit counter. For the deriving of the hopping sequence the entire LAP (24 bits), 4 LSB’s (4 bits) (Input 1) and the 27 MSB’s of the clock (Input 2) are used. With this input values different mathematical procedures (permutations, additions, XOR-operations) are performed to generate the sequence. This will be done at the beginning of every new transmission. The output constitutes a pseudorandom sequence covering 79 hop channels. For short transmissions the Bluetooth systems have the following behaviour: When the first connection between two devices is established, a hopping sequence is generated. If for transmitting the wanted data the complete hopping sequence is not used, the connection is ended. When a second connection is established. A new hopping sequence is generated. Due to the fact that the Bluetooth clock has a different value, because the period between the two transmission is longer (it cannot be shorter) than the minimum resolution of the clock (312,5 μs). The hopping sequence will always differ from the first one.

15.247 (h) Statement CETECOM S.A. – ITA team Page 1 of 1 Bluetooth devices 15.247 (h) Statement – Bluetooth devices Date: 27/01/2003 Bluetooth units which want to communicate with other units must be organised in an structure called piconet. This piconet consist of max. 8 Bluetooth units. One unit it the master of the other seven are the slaves. The master co- ordinates frequency occupation in this piconet for all units, the master determines the hopping sequence and the slave follows this sequence. Both devices shift between RX and TX time slot according to the clock of the master. As the master hop sequence is derived from its BD address which is unique for each Bluetooth device, additional masters intending to establish new piconets will allways use different hop sequence.

Authorisation letter (Power of attorney) We, SouthWing, S.L. C/ Llacuna, 162. Edificio Barcelona Activa. 08018 - Barcelona SPAIN authorise Cetecom S.A. Parque Tecnologico de Andalucía C/ Severo Ochoa 2 29590 Campanillas – Málaga Spain to act as our agent and to process and sign on our behalf for all approval activities in the United States of America. This authorisation is applicable to the product: Brand name: Southwing Model: Neo-507 FCC ID: RPGCAPR Signed on behalf of SouthWing, S.L. by Name: Sergi Torrents Date: 4 th November 2004 Place: Barcelona (SPAIN)

D D E E C C L L A A R R A A T T I I O O N N O O F F C C H H A A N N G G E E S S SouthWing, S.L. C/ Llacuna, 162. Edificio Barcelona Activa. 08018 – Barcelona (España) Declares that the equipment Type of equipment: Bluetooth headset Manufacturer: SouthWing, S.L. Brand name: SouthWing Model: Neo-507 FCC ID: RGPCAPR Is based in a slight modification of the previously approved equipment Type of equipment: Bluetooth headset Manufacturer: SouthWing, S.L. Brand name: SouthWing Model: Neo-102 FCC ID: RGPGUEL The changes can be summarized as follows: 1. Change in the plastic cover 2. Change in the power supply 3. Change in the content of the users manual 4. Slight changes in the PCB outline C C H H A A N N G G E E I I N N T T H H E E P P L L A A S S T T I I C C C C O O V V E E R R The electronic and RF part is mounted in a different plastic cover C C H H A A N N G G E E I I N N T T H H E E P P O O W W E E R R S S U U P P P P L L Y Y The equipment is distributed with two new AC/DC power adaptors. C C H H A A N N G G E E S S I I N N T T H H E E C C O O N N T T E E N N T T O O F F T T H H E E U U S S E E R R S S M M A A N N U U A A L L The manual includes additional information to support the Hands free profile of the Bluetooth specification. C C H H A A N N G G E E S S I I N N T T H H E E P P C C B B O O U U T T L L I I N N E E ß Slight changes in the PCB outline to accommodate the new plastic cove and new power supply adaptor: ß PCB edge moved 0.8mm towards the center ß Battery and Speaker holes moved Based on these changes we consider that the test report test report 18878RET.101 of the equipment RGPGUEL is fully applicable to the equipment RGPCAPR. Additional testing according to § 15.107 has been performed in order to cover the new power adaptors. Signed on behalf of SouthWing, S.L. by Name: Sergi Torrents Date: 4 th November 2004 Place: Barcelona (SPAIN)

Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 November 28, 2004 TO WHOM IT MAY CONCERN Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552 (b)(4) of the Freedom of Information Act, SouthWing, S.L. requests confidentiality for the following products: FCC ID Number Product Title/Model RPGCAPR Bluetooth Wireless Heaset/Neo-507 For the product stated above, we request that the following information be held confidential: 1) Electrical Schematics of the Circuitry 2) Block Diagram 3) Part Lists 4) Operational Description No other items submitted as part of the equipment authorization filing process are deemed confidentia l. The above exhibits contain SouthWing, S.L. trade secrets and proprietary information that could be of benefit to our competitors regarding the design of our wireless headset. This material is not customarily available to the general public and we request that it be withheld request that it be withheld from public inspection. If you have any questions, please feel free to contact me at the address shown below. Sincerely, P.A. Mr. Sergi Torrents Business Development Manager SouthWing, S.L. C/ Llacuna, 162. Edificio Barcelona Activa. 08018 - Barcelona, SPAIN TEL: +34 934019757 E-mail: [email protected]

Página 2-2 Página 2-3 Página 2-4


 
            
  ! "#$%#
  ! "#$%# &
 '  $() ( # * ( !( + *
*, +  #-   #   $%#. #/ $  +    ((   0    ( (1$2  $%#3%   #( .&
 '  $() ( # * ( !( + *
*, +  #-   #   $%#. #/ $  +

Página 2-5 Página 2-6

attn: Reviewing Engineer Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 November 28, 2004 RE: RF exposure information FCC ID: RGPGUEL FCC ID Number Product Title/Model RPGCAPR Bluetooth Wireless Headset/Neo-507 TO WHOM IT MAY CONCERN The product stated above, comply with the FCC limits for Human exposure to RF emissions. This device is categorically excluded from routine environmental because it operate at very low power level. The equipment is deemed to comply with the SAR or MPE limits without testing due to this very low power level (EIRP < 2.5 mW) Sincerely, P.A. Mr. Sergi Torrents Business Development Manager SouthWing, S.L. C/ Llacuna, 162. Edif…

Text truncated - open the document above for the full version.