RJYG5GSM Alarm System

Printed in Hong Kong PA: OI-G5/EN-Oct.2012-V1.0 GSM Alarm System GSM Alarm System FCC Statement FeaturesControl Panel Layout 2 1 ARM + Auror CPU Support 10 remote controls, 50 wireless sensors and 50 RFID tags Built-in 1,000,000 RF codes combination maintains high reliability Cellular communicator, simple operation Store 5 phone numbers, 1 speed-dial number, and 1 RFID SMS notification number Exit and entry delay SMS alert for low battery of two-way accessories Arm and disarm the system by SMS or free phone call Remote monitoring site via phone Built-in loud speaker for siren and two-way talking Built-in two pieces of 800mAh lithium batteries enable 5-hour standby SMS alerts for power failure, power recovery and low battery 850/1900MHz GSM frequency, applicable for universal GSM Signal Indicator GSM network searching: Flashes once every second GSM signal in normal: Flashes once every two seconds Touch Keypad Status Indicator RFID Reader / Play Voice Memo Stay Arm (Home Mode) Disarm Arm Call Record Voice Memo / Connect Button Bottom 4 3 Arm Home mode Disarm on keypad: Disarm by RFID tag: Press to arm the system. Press to arm the sytem in home mode. All the sensors in Normal Zone are armed except those in Home Mode Zone which are disarmed so that user can move freely at home. Input 4 digits password (default:1234) , and press to disarm the system after one beep. If three beeps are heard, password is wrong and please input again. Induce the RFID tag to the RFID Reader area to disarm the system. MIC Buzzer Back-up Batteries Loudspeaker Tamper Switch Record / Play Voice Memo Press to record 10 seconds voice messages. Or send SMS to system for calling back to record the voice messages. The Play Voice Memo Button will be flashing in purple to remind you. Users can touch the center of circle to listen to the voice memo. The LED indicator blacks out when the voice memo is played. Replay by touching it again. 6 5 Bottom SIM Card Slot Power On/Off Input for Wired Sensors (24-hour zone) Output for Electronic Lock Adapter Interfa ce Output for Wired Siren ≤ 500mA Input for Wired Sensors (normal zone) 8 7 Speed Dial Phone Call Electronic Lock Output Press Call Button , the panel auto dials to pre-stored phone number of the host, the LED blacks out after talk. User can also press Call Button to end talk. Dial phone number and then press Call Button to start talk, the LED blacks out after talk. User can also press Call Button to end talk. When system is disarmed, the output signal opens electronic lock automatically. SMS Operation ? Insert a SIM card to the control panel, then send a text of to the SIM card number, the operation guide message will be replied. You can control the alarm system by following the guide message: “?” System replies first grade guide menu: ‘0’ Disarm ‘1’ Arm ‘2’ Home mode ‘3’ Two-way talk ‘4’ Call-back voice memo ‘00’ Settings inquiry ‘??’ Store phone and SMS No. Send: 10 9 ??? System replies third grade guide menu: ‘91~99’ Zone name ‘10’ RFID tags SMS notice ‘11’ Entry and exit delay time ‘12’ Siren volume and ringing time ‘13’ Disarm password ‘14’ Single zone delay time Send: ?? ‘5’ Store alarm phone No. ‘6’ Store alarm SMS No. ‘7’ Store SMS No. for RFID tags ‘8’ Store speed dial phone No. ‘???’ System setups System replies second grade guide menu: Send: 0 Disarm Send: System disarmed. Arm Stay Arm (Home Mode) 12 11 2 Send: System in home mode. 1 Send: System armed. 4 3 Two-Way Talk Sendto the SIM card number, the alarm will call back. Pick up the phone and start two-way talk. ‘3’ Call-Back to Record Voice Memo Sendto the SIM card number, the alarm will call back. Pick up the phone, and leave 10 seconds message. The panel will hang up after 10 seconds. ‘4’ Send: Send: Settings Inquiry 14 13 00 System status Entry and exit delay time: 0sec Single zone delay time: 30sec Siren volume: 2 Siren ringing time: 5min Disarm password: 1234 Send: Note: Value of default setting will be changed once users finish programming. 5 Send: Store Alarm Phone No. TEL: 1. 2. 3. 4. 5. TEL: 1. 67890033 2. 67890022 3. 67890011 4. 67890000 5. For ward > Edit Store alarm phone No. successfully. Store Alarm SMS No. 16 15 6 Send: SMS: 1. 2. 3. 4. 5. SMS: 1. 67890033 2. 67890022 3. 67890011 4. 67890000 5. For ward > Edit Store alarm SMS No. successfully. Note: Only after SMS No. is stored, and the RFID tags SMS notice is changed, users can receive notice SMS once someone disarms the system by RFID tag. 7 Store SMS No. for RFID tags Send: For ward > Edit Store SMS No. for RFID tags successfully. SMS No. for RFID tags (0-20 digits): 1. SMS No. for RFID tags (0-20 digits): 1. 67890033 Note: Only after SMS No. is stored, and the RFID tags SMS notice is changed, users can receive notice SMS once someone disarms the system by RFID tag. Store Speed Dial Phone Number 18 17 8 Send: Speed dial phone number (0-20 digits): 1. 67890033 For ward > Edit Store speed dial phone number successfully. Speed dial phone number (0-20 digits): 1. 91 Change Zone Name Special Tips! stth Users can change the 1 ~ 9 zone names. The zone name should be 30 English characters at most for each line due to SMS character limit. Other alarm zones are fixed as Zone 10 alarm, Zone 11 alarm and so on. Send: 91~99 Zone1 name: Zone 1 alarm Zone1 name: Entrance door sensor For ward > Edit Change zone name successfully. SMS Alert for Low Battery of Accessories (available for two-way accessories such as DWC-102 and PIR-900/910) SMS will be sent for 1-9 zones with its zone name as “Zone name + low battery”. SMS alert for 10~50 zones will be “Zone number + low battery”. (available for two-way accessories such as DWC-102 and PIR-900/910) SMS will be sent for 1-9 zones with its zone name as “Zone name + tamper alarm”. SMS alert for 10~50 zones will be “Zone number + tamper alarm”. 20 19 Bedroom PIR tamper alarm. Zone 10 tamper alarm. Zone 10 low battery. Bedroom PIR low battery. SMS Alert for Tamper Alarm of Accessories 10 Change RFID Tags SMS Notice Se…

Text truncated - open the document above for the full version.

Chuango Security Technology Co., Ltd. December 25, 2012 To: SIEMIC, INC. 775 Montague Expressway Milpitas , CA 95035 USA Dear Sir/Madam, Re: Project and Product Certification Representative Authorization Letter We, ______ Chuango Security Technology Co., Ltd. ___hereby authorize SIEMIC, INC. to act as a Certification Body for certifying for the following project(s): Product Description: GSM Alarm System Model name: CG-G5 FCC ID: RJYG5 We affirm that between SIEMIC and __ Chuango Security Technology Co., Ltd. ___, any difference in understanding, including test plan, measurement methods, applicable standards and relevant procedures and processes have been resolved prior to commencement of testing activities. Sincerely, Client’s signature: Client’s name / title: Ken Li / CEO Contact information / address: 6-17, Overseas Students Pioneer Park, No. 108, Jia Economic & Technological Development Zone, Fuzhou 350015, China

SCS-F19: Confidentiality Request Letter Page 1 of 1 Rev 2.0 Chuango Security Technology Co., Ltd. December 25, 2012 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Confidentiality Request regarding application for certification of FCC ID: RJYG5 We hereby request confidential treatment of information accompanying this application as outlined below: - Block Diagram - Operational Description - Schematic The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Client’s signature: Client’s name / title: Ken Li / CEO Contact information / address: 6-17, Overseas Students Pioneer Park, No. 108, Jia Economic & Technological Development Zone, Fuzhou 350015, China

FCC Certification label Sample FCC ID: RJYG5 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Contains Transmitter Module FCC ID: UDV-0912142009007

FCC Certification Label Location Sample Label location

Receiving RFID signal antenna Receiving 315.8599MHz signal antenna GSM Modular (Single Modular) 315.8599MHz Modular

Page 1 of 24 FCC ID: RJYG5 ACCURATE TECHNOLOGY CO. LTD Report No. ATE20122853 APPLICATION CERTIFICATION FCC Part 15B On Behalf of Chuango Security Technology Co., Ltd. GSM Alarm System Model No.: CG-G5 FCC ID: RJYG5 Prepared for : Chuango Security Technology Co., Ltd. Address : 6-17, Overseas Students Pioneer Park, No. 108, Jia Economic & Technological Development Zone, Fuzhou 350015, China Prepared by : ACCURATE TECHNOLOGY CO. LTD Address : F1, Bldg. A, Changyuan New Material Port, Keyuan Rd. Science & Industry Park, Nanshan, Shenzhen, Guangdong P.R. China Tel: (0755) 26503290 Fax: (0755) 26503396 Report Number : ATE20122853 Date of Test : December 20-29, 2012 Date of Report : December 30, 2012 Page 2 of 24 FCC ID: RJYG5 ACCURATE TECHNOLOGY CO. LTD Report No. ATE20122853 TABLE OF CONTENTS Description Page Test Report Certification 1. GENERAL INFORMATION .......................................................................................................... 4 1.1. Description of Device (EUT)....................................................................................................................4 1.2. Accessory and Auxiliary Equipment ........................................................................................................4 1.3. Description of Test Facility ......................................................................................................................5 1.4. Measurement Uncertainty.........................................................................................................................5 2. MEASURING DEVICE AND TEST EQUIPMENT ..................................................................... 6 3. OPERATION OF EUT DURING TESTING ................................................................................. 7 3.1. Operating Mode ........................................................................................................................................7 3.2. Configuration and peripherals ..................................................................................................................7 4. TEST PROCEDURES AND RESULTS ......................................................................................... 8 5. CONDUCTED EMISSION FOR FCC PART 15 SECTION 15.107(A) ...................................... 9 5.1. Block Diagram of Test Setup....................................................................................................................9 5.2. The Emission Limit ..................................................................................................................................9 5.3. Configuration of EUT on Measurement .................................................................................................10 5.4. Operating Condition of EUT ..................................................................................................................10 5.5. Test Procedure ........................................................................................................................................10 5.6. Power Line Conducted Emission Measurement Results ........................................................................11 6. RADIATED EMISSION FOR FCC PART 15 SECTION 15.109(A)......................................... 14 6.1. Block Diagram of Test Setup..................................................................................................................14 6.2. The Emission Limit For Section 15.109 (a) & 15.209 ...........................................................................15 6.3. EUT Configuration on Measurement .....................................................................................................15 6.4. Operating Condition of EUT ..................................................................................................................15 6.5. Test Procedure ........................................................................................................................................16 6.6. The Emission Measurement Result ........................................................................................................17 Page 3 of 24 FCC ID: RJYG5 ACCURATE TECHNOLOGY CO. LTD Report No. ATE20122853 Test Report Certification Applicant : Chuango Security Technology Co., Ltd. Manufacturer : Chuango Security Technology Co., Ltd. EUT Description : GSM Alarm System (A) MODEL NO.: CG-G5 (B) SERIAL NO.: N/A (C) POWER SUPPLY: DC 12V (Power by adapter) & DC 3.7V (“BL-5B” battery 2×) Measurement Procedure Used: FCC Rules and Regulations Part 15 Subpart B ANSI C63.4: 2009 The device described above is tested by ACCURATE TECHNOLOGY CO. LTD to determine the maximum emission levels emanating from the device. The maximum emission levels are compared to the FCC Part 15 Subpart B limits. The measurement results are contained in this test report and ACCURATE TECHNOLOGY CO. LTD is assumed full responsibility for the accuracy and completeness of these measurements. Also, this report shows that the Equipment Under Test (EUT) is to be technically compliant with the FCC requirements. This report applies to above tested sample only. This report shall not be reproduced in part without written approval of ACCURATE TECHNOLOGY CO. LTD. Date of Test : December 20-29, 2012 Prepared by : (Apple Lv, Engineer) Approved & Authorized Signer : (Sean Liu, Manager) Page 4 of 24 FCC ID: RJYG5 ACCURATE TECHNOLOGY CO. LTD Report No. ATE20122853 1. GENERAL INFORMATION 1.1. Description of Device (EUT) EUT : GSM Alarm System Model Number : CG-G5 Power Supply : DC 12V (Power by adapter) & DC 3.7V (“BL-5B” battery 2×) Adapter : M/N: FKS106HSC-1200500U Input: AC 100-240V; 50/60Hz Output: DC 12V/500mA Receiver Frequency : 315.8599MHz & 125KHz GSM Modular : Single Modular 824.2-848.8MHz 1850.2-1909.8MHz ID: UDV-0912142009007 Applicant : Chuango Security Technology Co., Ltd. Address : 6-17, Overseas Students Pioneer Park, No. 108, Jia Econom…

Text truncated - open the document above for the full version.

Conducted emissions test Radiated emissions test < 30MHz Radiated emissions test 30MHz- 1GHz Radiated emissions test > 1GHz