RNIP731607-HPS2 BASIC WIRELESS CONTROLLER

How to use: Step 1: Insert the controller's receiver into the Player 1 slot. Note: - Do not insert the controller's receiver into a memory card slot. -Switch off the console before inserting the controller's receiver. Step 2:Once the receiver is inserted you may turn on your console. Step 3:Turn on the wireless controller and set the channel as same as the receiver. (example. If the receiver is set to channel 2, please adjust the controller channel to channel 2.) Step 4:When the receiver is first plugged into the console, the LED is OFF.Once the controller has detected the receiver, the LED on the receiver will turn ON. The controller is now ready to use. Note: Turn off the controller’s power if not in use. Sleep Mode: The controller will shut down automatically if it cannot detect the receiver after one minute or if the controller is not in use for more than 4 minutes. You can reactivate the controller by pressing the START or SELECT button or by switching the power button to OFF and ON again. Low Power Indication: The power LED will blink when the batteries are low, replace both batteries with new ones. R1 R2 L1 L2 c) Controller's receiver Battery Replacement: - Open the battery compartment door. - Insert the batteries as marked on the bottom of the battery compartment. - Close the battery compartment door. You are now ready to use your wireless controller. Note: - For longer playing time, use Alkaline batteries. -Do not mix fresh and used batteries. This will reduce the controller's transmitting and receiving distance and may cause the product to malfunction. -Rechargeable batteries can be used with this product (rechargeable batteries are not included). - Dispose of used batteries according to the battery manufacturer's instructions. Thank you for purchasing Hip Gear’s 2.4GHz Wireless Controller for all PlayStation consoles. Please read this manual carefully before use. Features: - Fully compatible with all PS2 consoles (PS2, PSOne and PSX) - Power on/off selection - Twin analog sticks - Rubber grips - 10 Meters(30ft) RF wireless transmitting & receiving distance - Dual channel selection to allow up to 2 players at the same time - Low power Indicator - Uses 2 AA size batteries Button Name for Hip Gear’s 2.4GHz Wireless Controller: a) Controller (front view) b) Controller (top view) PS2 2.4GHz Wireless Controller Instruction Manual CHANNEL SELECTION SWITCH SELECT START ANALOG CH1/POWER/CH2 OFF POWER R3 L3 D-PAD FIRE BUTTONS LED NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. There is no guarantee that some form of interference will not occur in a particular installation.If this equipment does cause interference to radio or television reception, the user is encouraged to try one or more of the following corrective measures: Reorient or relocate the receiving antenna; Increase the separation between the equipment and receiver; Connect the equipment into an outlet on a circuit different from that which the receiver is connected to; Consult an experienced radio / TV technician for assistance. FEDERAL COMMUNICATIONS COMMISSION This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.

REPORT NO. : FR492802-01 SPORTON International Inc. PAGE NUMBER : A1 OF A9 TEL : 886-2-2696-2468 ISSUED DATE : Nov. 12, 2004 FAX : 886-2-2696-2255 APPENDIX A. Photographs of EUT REPORT NO. : FR492802-01 SPORTON International Inc. PAGE NUMBER : A2 OF A9 TEL : 886-2-2696-2468 ISSUED DATE : Nov. 12, 2004 FAX : 886-2-2696-2255

FCC ID: RNIP731607-H Label Location

REPORT NO. : FR492802-01 SPORTON International Inc. PAGE NUMBER : A3 OF A9 TEL : 886-2-2696-2468 ISSUED DATE : Nov. 12, 2004 FAX : 886-2-2696-2255 REPORT NO. : FR492802-01 SPORTON International Inc. PAGE NUMBER : A4 OF A9 TEL : 886-2-2696-2468 ISSUED DATE : Nov. 12, 2004 FAX : 886-2-2696-2255 REPORT NO. : FR492802-01 SPORTON International Inc. PAGE NUMBER : A5 OF A9 TEL : 886-2-2696-2468 ISSUED DATE : Nov. 12, 2004 FAX : 886-2-2696-2255 REPORT NO. : FR492802-01 SPORTON International Inc. PAGE NUMBER : A6 OF A9 TEL : 886-2-2696-2468 ISSUED DATE : Nov. 12, 2004 FAX : 886-2-2696-2255 REPORT NO. : FR492802-01 SPORTON International Inc. PAGE NUMBER : A7 OF A9 TEL : 886-2-2696-2468 ISSUED DATE : Nov. 12, 2004 FAX : 886-2-2696-2255 REPORT NO. : FR492802-01 SPORTON International Inc. PAGE NUMBER : A8 OF A9 TEL : 886-2-2696-2468 ISSUED DATE : Nov. 12, 2004 FAX : 886-2-2696-2255 REPORT NO. : FR492802-01 SPORTON International Inc. PAGE NUMBER : A9 OF A9 TEL : 886-2-2696-2468 ISSUED DATE : Nov. 12, 2004 FAX : 886-2-2696-2255

FCC ID: RNIP731607-H Issued on Nov. 12, 2004 Report No.: FR492802-01 SPORTON International Inc. TEL : 886-2-2696-2468 FAX : 886-2-2696-2255 FCC TEST REPORT CATEGORY : Portable PRODUCT NAME : PS2 Basic Wireless Controller FCC ID. : RNIP731607-H FILING TYPE : Certification BRAND NAME : Hip Interactive MODEL NAME : LM607 APPLICANT : Esel International Co. Ltd Rm 15-17, 5/F, Cardinal Ind, Bldg, No. 17 On Lok Mun St., Fanling, N.T., Hong Kong MANUFACTURER : Eastern Sources Electronics Manufacturer Daji Industrial Zone, Hengshan District, Shipai Town, Dongguan City, Guangdong, China ISSUED BY : SPORTON INTERNATIONAL INC. 6F, No. 106, Sec. 1, Hsin Tai Wu Rd., His Chih, Taipei Hsien, Taiwan, R.O.C. Statements: The test result in this report refers exclusively to the presented test model / sample. Without written approval of SPORTON International Inc., the test report shall not be reproduced except in full. Certificate or Test Report could not be used by the applicant to claim the product endorsement by CNLA, NVLAP or any agency of U.S. government. The test equipment used to perform the test are calibrated and traceable to NML/ROC or NIST/USA. Dr. Alan Lane Vice General Manager Sporton International Inc. Lab Code: 200079-0 FCC ID: RNIP731607-H Issued on Nov. 12, 2004 Report No.: FR492802-01 SPORTON International Inc. Page No. : i TEL : 886-2-2696-2468 Issued Date: Nov. 12, 2004 FAX : 886-2-2696-2255: Table of Contents History of this test report....................................................................................................................................ii CERTIFICATE OF COMPLIANCE.......................................................................................................................iii 1. General Description of Equipment under Test.............................................................................................1 1.1. Applicant ......................................................................................................................................................................................... 1 1.2. Manufacturer ................................................................................................................................................................................... 1 1.3. Basic Description of Equipment under Test.................................................................................................................................... 1 1.4. Features of Equipment under Test ................................................................................................................................................. 1 1.5. Table for Carrier Frequencies ......................................................................................................................................................... 2 2. Test Configuration of the Equipment under Test.........................................................................................3 2.1. Connection Diagram of Test System .............................................................................................................................................. 3 2.2. The Test Mode Description............................................................................................................................................................. 3 2.3. Description of Test Supporting Units .............................................................................................................................................. 3 3. General Information of Test............................................................................................................................4 3.1. Test Facility ..................................................................................................................................................................................... 4 3.2. Test Conditions ............................................................................................................................................................................... 4 3.3. Standards for Methods of Measurement......................................................................................................................................... 4 3.4. DoC Statement ............................................................................................................................................................................... 4 3.5. Frequency Range Investigated ....................................................................................................................................................... 4 3.6. Test Distance .................................................................................................................................................................................. 4 3.7. Test Software .................................................................................................................................................................................. 4 4. List of Measurements......................................................................................................................................5 4.1. Summary of the Test Results.......................................................................................................................................................... 5 5. Test Result .......................................................................................................................................................6 5.1. Test of Maximum Carrier Field Strength ......................................................................................................................................... 6 5.2. Test of Band Edges Emission......................................................................................................................................................... 8 5.3. Test of AC Power Line Conducted Emiss…

Text truncated - open the document above for the full version.

FRONT VIEW REAR VIEW 492802-01 492802-01 FRONT VIEW REAR VIEW