RNIX832616-DBluetooth Controller

b) Controller (Top View) c) Receiver d) Headset / Earphone Battery Replacement: a) Open the battery compartment door. Note: The controller and the receiver must be connected before assigning a Turbo Fire to any of the action buttons. The Turbo LED will remain lit when any button has Turbo Fire assigned to it. To Clear a Turbo assigned button: 1) Press and hold the Clear button, the Clear LED lights up. 2) Press the button which has been set to Turbo Fire, the Turbo LED turns off. The Turbo Fire of the button is now clear. Repeat this procedure for any other Turbo Fire cancellation. Low Power Indication: The controller’s LED starts to blink 2 times per second when the power is low. When this occurs, replace all your batteries with new ones. For technical assistance please visit our website: www.hipgearproducts.com 6. a) Wear the headset as shown in figure1: 6. b) Adjust the bendable hook of the headset to custom fit securly around your ear as shown in figure 2: 6. c)Adjust the microphone as shown in figure 3 as close to your mouth as possible to achieve the best sound quality. 7) Adjust the volume accordingly. When activating the on-line function of the XB-Comm you must be within 1~2 meters (roughly 3~6 ft.) of your console to ensure a strong signal. Press and hold the on-line button for 3 seconds (the LED will turn green). Once you are connected, you can then move away from your console. Please see the manual for further instruction on proper use of your XB-Comm controller. Y XB A S T A R T B A C K Y XB A S T A R T B A C K C L E A R T U R B O LED light-up 3)Slide the power switch to the ON position on the controller. The controller’ s LED will also start to blink. The LED of the controller and the LED of the receiver will stop blinking when the connection has been completed. 4) If you want to play your game with vibration feedback, place the power switch into the vibration position. 5) Plug the headset / earpiece into the earphone jack of the controller and place the earpiece around either ear. How to use Hip Gear Headset: To achieve the best voice communication and headset comfort when using your XB-Comm on-line, follow all the instructions outlined in this manual about adjusting the headset. b) Place the batteries into the controller (as marked on the bottom of the battery compartment). c) Close the battery compartment door. You are now ready to use your XB-Comm TM Bluetooth ® Xbox ® Wireless Controller & Headset. Note: - For longer playing time, always use Alkaline batteries. - Do not mix new and used batteries, this will reduce the controller’s transmitting and receiving distance and may cause the product to malfunction. - Rechargeable batteries can be used with this product (rechargeable batteries are not included). - Dispose of used batteries according to the battery manufacturer’s instructions. How to Use: 1) Turn on the power of the Xbox ® console. 2) Plug the receiver into the first controller slot of the Xbox ® console. The LED of the receiver will start to blink. Note:Do not plug more than one receiver into the console at the same time. You must wait until the first receiver has been connected to its controller before you plug in any other receivers; otherwise, a malfunction may occur. Thank you for purchasing Hip Gear’s XB-Comm TM Bluetooth ® Xbox ® Wireless Controller & Headset for the Xbox ® Console. Please read this instruction manual thoroughly before use. Features: - Fully compatible with Xbox ® & Xbox Live TM . - Bluetooth ® Wireless Technology to ensure maximum signal strength - Auto channel scanning - Light weight headset with microphone for On-Line gaming - Turbo Fire - Dual Vibration Feedback motors - Low Battery Warning Indicator - Super long play time – up to 50 hours (with vibration deactivated) - Twin rubberized analog sticks and fully analog action buttons for precise control - Rubberized grips to ensure comfort and prevent slipping during game play - Optimal transmitting and receiving performance at 30ft. (10 meters) or less Button Configurations: a) Controller (Front View) Hip Gear XB-Comm TM Bluetooth ® Xbox ® Wireless Controller & Headset Y X A B Black White LT Back Start D-PAD RT Turbo Clear Off/On/Vibration Volume Adjustment Phone Jack L-Trigger R-Trigger Memory card slot Connection LED Indication How to Connect the Controller for On-Line Gaming: Press and hold the “on-line” button on the controller until the button’s LED turns green. You are now ready for on-line gaming! Mute Function: The mute function allows you to disable your microphone so your opponent cannot hear you speak while you are gaming on-line. While your microphone has been muted you will still be able to hear your opponent. To use the on-line mute function, simply press the controller’s “on-line” button once. The button’s LED will change from green to red. The mute function has now been activated. To deactivate the mute function, press the “on-line” button again. The button’s LED will change from red to green. The microphone will now be on. How to Deactivate the On-Line Function of the Controller: Press and hold the “on-line” button for 3 seconds. The green LED will go out and the on-line function of the controller will be deactivated. The controller can now only be used as a regular wireless Xbox controller. To reactivate the on-line function, press and hold the button until the button’s LED once again turns green. Note: It is recommended that you deactivate the on-line function when it is not in use. This will extend the life of the controller’s batteries. Turbo Fire Setting: Each action button of the controller has a built-in Turbo Fire Function. Simply follow the steps listed below to activate Turbo Fire: 1)Press and hold the Turbo button, the Turbo LED lights up. 2)Press the action button you wish to assign a Turbo Fire Function to. The Turbo LED will blink when the setting is successful. 3)The Turbo LED blinks rapidly whenever the assigned Turbo Fire button is pressed. 4) Repeat the…

Text truncated - open the document above for the full version.

Report No: ER/2005/40038 ID: RNIX832616-D Issue Date: Jun. 07, 2005 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw 0513 ILAC MRA APPENDIX 2 PHOTOGRPHS OF EUT Report No: ER/2005/40038 ID: RNIX832616-D Issue Date: Jun. 07, 2005 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw 0513 ILAC MRA Front View of EUT Back View of EUT Report No: ER/2005/40038 ID: RNIX832616-D Issue Date: Jun. 07, 2005 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw 0513 ILAC MRA Tip View of EUT

FCC ID LABEL FORMAT AND LOCATION Applicant: ESEL International Co., Ltd. FCC ID: RNIX832616-D FCC ID: RNIX832616-D This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID LABEL AREA

Report No: ER/2005/40038 ID: RNIX832616-D Issue Date: Jun. 07, 2005 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw 0513 ILAC MRA APPENDIX 3 PHOTOGRPHS OF EUT Report No: ER/2005/40038 ID: RNIX832616-D Issue Date: Jun. 07, 2005 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw 0513 ILAC MRA Open View of EUT-1 Report No: ER/2005/40038 ID: RNIX832616-D Issue Date: Jun. 07, 2005 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw 0513 ILAC MRA Open View of EUT-2 Internal View of EUT – 1 Report No: ER/2005/40038 ID: RNIX832616-D Issue Date: Jun. 07, 2005 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw 0513 ILAC MRA Internal View of EUT – 2 Internal View of EUT – 3 Report No: ER/2005/40038 ID: RNIX832616-D Issue Date: Jun. 07, 2005 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw 0513 ILAC MRA Internal View of EUT – 4 Internal View of EUT – 5 Ant Report No: ER/2005/40038 ID: RNIX832616-D Issue Date: Jun. 07, 2005 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw 0513 ILAC MRA Internal View of EUT – 6

Report No: ER/2005/40038 ID: RNIX832616-D Issue Date: Jun. 07, 2005 Page: 1 of 61 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw 0513 ILAC MRA ELECTROMAGNETIC EMISSIONS COMPLIANCE REPORT INTENTIONAL RADIATOR CERTIFICATION TO FCC PART 15 SUBPART C REQUIREMENT OF Product Name: XBOX Blue-Tooth Controller with Headset Host/Device Brand Name: N/A Model Name: LM616 Model Difference: N/A FCC ID: RNIX832616-D Report No.: ER/2005/40038 Issue Date: Jun. 07, 2005 FCC Rule Part: §15.247 Prepared for ESEL International Co., Ltd. Rm15-18, 5/F., Cardinal Industrial Building, 17 On Lok Mun St., Fanling, N.T. Hong Kong Prepared by SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei County, Taiwan. Note: This report shall not be reproduced except in full, without the written approval of SGS Taiwan Ltd. This document may be altered or revised by SGS Taiwan Ltd. personnel only, and shall be noted in the revision section of the document. Report No: ER/2005/40038 ID: RNIX832616-D Issue Date: Jun. 07, 2005 Page: 2 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw 0513 ILAC MRA VERIFICATION OF COMPLIANCE Applicant: ESEL International Co., Ltd. Rm15-18, 5/F., Cardinal Industrial Building, 17 On Lok Mun St., Fanling, N.T. Hong Kong. Equipment Under Test: XBOX Blue-Tooth Controller with Headset Host/Device Brand Name: N/A FCC ID Number: RNIX832616-D Model No.: LM616 Model Difference: N/A File Number: ER/2005/40038 Date of test: Apr. 29, 2005 ~ May. 31, 2005 Date of EUT Received: Apr. 29, 2005 We hereby certify that: The above equipment was tested by SGS Taiwan Ltd. The test data, data evaluation, test proce- dures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4 (2003) and the energy emitted by the sample EUT tested as described in this report is in compliance with conducted and radiated emission limits of FCC Rules Part 15.247 The test results of this report relate only to the tested sample identified in this report. Test By: Date Jun. 07, 2005 Sky Wang Prepared By: Date Jun. 07, 2005 Gigi Yeh Approved By: Date Jun. 07, 2005 Vincent Su Report No: ER/2005/40038 ID: RNIX832616-D Issue Date: Jun. 07, 2005 Page: 3 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw 0513 ILAC MRA Version Version No. Date 00 Jun. 07, 2005 Report No: ER/2005/40038 ID: RNIX832616-D Issue Date: Jun. 07, 2005 Page: 4 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw 0513 ILAC MRA Table of Contents 1. GENERAL INFORMATION .........................................................................................................7 1.1. Product Description ............................................................................................................................7 1.2. Related Submittal(s) / Grant (s) ..........................................................................................................7 1.3. Test Methodology ...............................................................................................................................7 1.4. Test Facility.........................................................................................................................................7 1.5. Special Accessories .............................................................................................................................7 1.6. Equipment Modifications....................................................................................................................7 2. SYSTEM TEST CONFIGURATION ............................................................................................8 2.1. EUT Configuration .............................................................................................................................8 2.2. EUT Exercise ......................................................................................................................................8 2.3. Test Procedure.....................................................................................................................................8 2.4. Configuration of Tested System..........................................................................................................9 3. SUMMARY OF TEST RESULTS ...............................................................................................10 4. DESCRIPTION OF TEST MODES ............................................................................................10 5. CONDUCTED EMISSION TEST................................................................................................11 5.1. Standard Applicable ......................................................................................…

Text truncated - open the document above for the full version.

Report No: ER/2005/40038 ID: RNIX832616-D Issue Date: Jun. 07, 2005 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw 0513 ILAC MRA APPENDIX 1 PHOTOGRPHS OF SET UP Report No: ER/2005/40038 ID: RNIX832616-D Issue Date: Jun. 07, 2005 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw 0513 ILAC MRA Radiated Emission Set up Photos