ROR20055G Enterprise Micro Cell

www.nemko.com Nemko Canada Inc., a testing laboratory, is accredited by ANSI National Accreditation Board (ANAB). The test results included in this report are within the scope of this accreditation. The ANAB symbol is an official symbol of the ANSI National Accreditation Board, used under licence. FCC and ISED RSS-102– MPE Calculation; Date: January 2026 RF Exposure Compliance – MPE Calculation Report C h o o s e S c a n d i n a v i a n t r u s t Applicant company: BLiNQ Networks Inc. Model number: MCRF400-36 Model name: MCRF-400 FCC Identification: FCC ID: ROR2005 Product type: Fixed Device Device category Consumer Device for General Population/Uncontrolled Exposure Date of issue: April 14, 2026 Compliance Specifications: FCC 47 CFR Part 1 Subpart I, §§1.1307, 1.1310 FCC 47 CFR Part 2 Subpart J, §§2.1091, 2.1093 FCC KDB 447498 D01 General RF Exposure Guidance v06 FCC KDB 865664 D01 RF Exposure Procedures and Equipment Authorization Policies MPE calculation report Product info: FCC ID: ROR2005 Model: MCRF400-36 Page 2 of 6 Test locations of Nemko Canada Inc. Ottawa site Montréal site GTA Cambridge site Facility address 303 River Road Ottawa, Ontario Canada K1V 1H2 Tel: +1 613 737 9680 Fax: +1 613 737 9691 292 Labrosse Avenue Pointe-Claire, Québec Canada H9R 5L8 Tel: +1 514 694 2684 Fax: +1 514 694 3528 1-130 Saltsman Drive Cambridge, Ontario Canada N3E 0B2 Tel: +1 519 650 4811 Test site identifier - FCC CA2040 CA2041 CA0101 Test site identifier – ISED Canada 2040A-4 2040G-5 24676 ANAB File Number AT-3195 AT-3193 AT-3194 Andrey Adelberg Senior EMC/Wireless Specialist Prepared by Signature Limits of responsibility The results presented in this report apply solely to the specific device model tested and are valid only for the operating conditions and installation requirements specified herein. Testing was conducted in accordance with ISO/IEC 17025:2017 requirements, and all results fall within the scope of Nemko Canada's accreditation. This MPE evaluation is based on the maximum power levels and operating conditions specified. Any modifications to the device hardware, software, or installation that could affect RF output power or antenna characteristics may invalidate this compliance demonstration. Copyright notification This report may be reproduced by the applicant in its entirety for regulatory submission and internal use. Any use of this report by third parties, including reliance on its contents or decisions made based on it, is solely at the risk of those third parties. Nemko Canada Inc. assumes no responsibility for any damages incurred by third parties as a result of actions taken based on this report. © Nemko Canada Inc. All rights reserved. MPE calculation report Product info: FCC ID: ROR2005 Model: MCRF400-36 Page 3 of 6 1. Executive Summary This report presents the Maximum Permissible Exposure (MPE) analysis to demonstrate compliance with FCC RF exposure requirements. The evaluation considers both single transmitter operation and simultaneous multi-transmitter scenarios where applicable. 2. Key Findings Compliance status Complies Critical separation distances 104 cm Special conditions or limitations N/A MPE calculation report Product info: FCC ID: ROR2005 Model: MCRF400-36 Page 4 of 6 MPE calculations for stand-alone transmission Device Classification Requirements Portable Device Definition (§2.1093) Devices designed for use by a person where the radiating structure is within 20 cm of the user's body require SAR evaluation rather than MPE calculation. Mobile Device Definition Devices installed in vehicles or with permanently installed antennas may use MPE calculations if minimum separation distances can be established. Fixed/Base Station Definition Stationary transmitters with controlled access to antenna locations may use MPE calculations for both occupational and general population exposure scenarios. 3. References, definitions and limits for FCC FCC §2.1091(d) (2) For operations within the frequency range of 300 kHz and 6 GHz (inclusive), the limits for maximum permissible exposure (MPE), derived from whole-body SAR limits and listed in Table 1 in paragraph (e)(1) of this section, may be used instead of whole-body SAR limits as set forth in paragraphs (a) through (c) of this section to evaluate the environmental impact of human exposure to RF radiation as specified in §1.1307(b) of this part, except for portable devices as defined in §2.1093 of this chapter as these evaluations shall be performed according to the SAR provisions in §2.1093. Table 1: §1.1310(e)(1)—Power Density Limits for Maximum Permissible Exposure (MPE) Frequency range (MHz) Power density (mW/cm 2 ) Averaging time (minutes) (i) Limits for Occupational/Controlled Exposure 0.3–3.0 *(100) ≤6 3.0–30 *(900 / f 2 ) <6 30–300 1.0 <6 300–1500 f / 300 <6 1500–100000 5 <6 (ii) Limits for General Population/Uncontrolled Exposure 0.3–1.34 *(100) <30 1.34–30 *(180 / f 2 ) <30 30–300 0.2 <30 300–1500 f / 1500 <30 1500–100000 1.0 <30 Notes: f = frequency in MHz. * = Plane-wave equivalent power density. MPE calculation report Product info: FCC ID: ROR2005 Model: MCRF400-36 Page 5 of 6 4. Power density calculation formula The fundamental equation (from page 18 of OET Bulletin 65, Edition 97-01) for calculating power density at a specified distance from an RF source is derived from the far-field assumption: 푆= 푃퐺 4휋푅 2 where: • S = Power density (mW/cm² or W/m²) • P = Power input to antenna (mW or W) • G = Antenna gain (linear ratio, not dB) • R = Distance from radiation center (cm or m) This equation assumes: • Far-field conditions (R > 2D²/λ, where D is largest antenna dimension) are assumed at the evaluation distance of 20 cm • Isotropic power distribution (conservative approach) • Free-space propagation conditions • Worst-case antenna orientation Multiple Transmitter Analysis (if applicable) Total Exposure Ratio (TER) Calculation: TER = Σ(Si/Li) ≤ 1.0 Where: • Si = Power density from transmitter i • Li = Applicable limit …

Text truncated - open the document above for the full version.

Model: MCRF400-36 Page 1 of 4 FCC ID: ROR2005 Section 1. Radiated emissions setup photos 1.1 Front view C h o o s e S c a n d i n a v i a n t r u s t Setup photos – PRJ0096610 Model: MCRF400-36 Page 2 of 4 FCC ID: ROR2005 Model: MCRF400-36 Page 3 of 4 FCC ID: ROR2005 1.2 Rear view Model: MCRF400-36 Page 4 of 4 FCC ID: ROR2005 END OF REPORT

BLiNQ Networks Inc. FCC ID: ROR2003 Models: PC-400, PCW-400, PWRF-400, PCRF-400 CBRS test verification Notes: Original hardware testing for this platform was performed using the indoor variant of the product (model PCW-400i), certified under FCC ID: ROR2002. For reference, see test report KSCR240700144905, issued February 21, 2025. All test cases listed below were re-verified with the product configured as the outdoor models PC-400, PCW-400, PWRF-400, and PCRF-400. The device is configured to meet Category B CBRS requirements for testing purposes, even though actual field deployment will utilize Category A, which imposes less stringent limits. Summary table Section Test Case ID DP Test Logs_DP Required for Cert Comments 6.1.4.1.1 WINNF.FT.C.REG.1 --  C1 Multi-Step registration 6.1.4.1.2 WINNF.FT.D.REG.2 X  C1 Domain Proxy Multi-Step registration 6.1.4.1.3 WINNF.FT.C.REG.3 --  C2 Single-Step registration for Category A CBSD 6.1.4.1.4 WINNF.FT.D.REG.4 X  C2 Domain Proxy Single-Step registration for Cat A CBSD 6.1.4.1.5 WINNF.FT.C.REG.5 --  C3 Single-Step registration for CBSD with CPI signed data 6.1.4.1.6 WINNF.FT.D.REG.6 X  C3 Domain Proxy Single-Step registration for CBSD with CPI signed data 6.1.4.1.7 WINNF.FT.C.REG.7 X  C6 Registration due to change of an installation parameter 6.1.4.2.1 WINNF.FT.C.REG.8 --  M Missing Required parameters (responseCode 102) 6.1.4.2.2 WINNF.FT.D.REG.9 X  M Domain Proxy Missing Required parameters (responseCode 102) 6.1.4.2.3 WINNF.FT.C.REG.10 --  M Pending registration (responseCode 200) 6.1.4.2.4 WINNF.FT.D.REG.11 X  M Domain Proxy Pending registration (responseCode 200) 6.1.4.2.5 WINNF.FT.C.REG.12 --  M Invalid parameter (responseCode 103) 6.1.4.2.6 WINNF.FT.D.REG.13 X  M Domain Proxy Invalid parameters (responseCode 103) 6.1.4.2.7 WINNF.FT.C.REG.14 --  M Blacklisted CBSD (responseCode 101) 6.1.4.2.8 WINNF.FT.D.REG.15 X  M Domain Proxy Blacklisted CBSD (responseCode 101) 6.1.4.2.9 WINNF.FT.C.REG.16 --  M Unsupported SAS protocol version (responseCode 100) 6.1.4.2.10 WINNF.FT.D.REG.17 X  M Domain Proxy Unsupported SAS protocol version (responseCode 100) 6.1.4.2.11 WINNF.FT.C.REG.18 --  M Group Error (responseCode 201) 6.1.4.2.12 WINNF.FT.D.REG.19 X  M Domain Proxy Group Error (responseCode 201) 6.1.4.3.1 WINNF.FT.C.REG.20 X  C2 Category A CBSD location update 6.3.4.2.1 WINNF.FT.C.GRA.1 X  M Unsuccessful Grant responseCode=400 (INTERFERENCE) 6.3.4.2.2 WINNF.FT.C.GRA.2 X  M Unsuccessful Grant responseCode=401 (GRANT_CONFLICT) 6.4.4.1.1 WINNF.FT.C.HBT.1 --  M Heartbeat Success Case (first Heartbeat Response) 6.4.4.1.2 WINNF.FT.D.HBT.2 X  M Domain Proxy Heartbeat Success Case (first Heartbeat Response) 6.4.4.2.1 WINNF.FT.C.HBT.3 X  M Heartbeat responseCode=105 (DEREGISTER) 6.4.4.2.2 WINNF.FT.C.HBT.4 --  M Heartbeat responseCode=500 (TERMINATED_GRANT) 6.4.4.2.3 WINNF.FT.C.HBT.5 X  M Heartbeat responseCode=501 (SUSPENDED_GRANT) in First Heartbeat Response 6.4.4.2.4 WINNF.FT.C.HBT.6 X  M Heartbeat responseCode=501 (SUSPENDED_GRANT) in Subsequent Heartbeat Response 6.4.4.2.5 WINNF.FT.C.HBT.7 X  M Heartbeat responseCode=502 (UNSYNC_OP_PARAM) 6.4.4.2.6 WINNF.FT.D.HBT.8 X  M Domain Proxy Heartbeat responseCode=500 (TERMINATED_GRANT) 6.4.4.3.1 WINNF.FT.C.HBT.9 X  M Heartbeat Response Absent (First Heartbeat) 6.4.4.3.2 WINNF.FT.C.HBT.10 X  M Heartbeat Response Absent (Subsequent Heartbeat) 6.4.4.4.1 WINNF.FT.C.HBT.11 X  O Successful Grant Renewal in Heartbeat Test Case 6.5.4.2.1 WINNF.FT.C.MES.1 --  C4 Registration Response contains measReportConfig 6.5.4.2.2 WINNF.FT.D.MES.2 X  C4 Domain Proxy Registration Response contains measReportConfig 6.5.4.2.3 WINNF.FT.C.MES.3 X  C5 Grant Response contains measReportConfig 6.5.4.2.4 WINNF.FT.C.MES.4 --  C5 Heartbeat Response contains measReportConfig 6.5.4.2.5 WINNF.FT.D.MES.5 X  C5 Domain Proxy Heartbeat Response contains measReportConfig 6.6.4.1.1 WINNF.FT.C.RLQ.1 --  M Successful Relinquishment 6.6.4.1.2 WINNF.FT.D.RLQ.2 X  M Domain Proxy Successful Relinquishment 6.6.4.2.1 WINNF.FT.C.RLQ.3 --  O Unsuccessful Relinquishment, responseCode=102 6.6.4.2.2 WINNF.FT.D.RLQ.4 X  O Domain Proxy Unsuccessful Relinquishment, responseCode=102 6.6.4.3.1 WINNF.FT.C.RLQ.5 --  O Unsuccessful Relinquishment, responseCode=103 6.6.4.3.2 WINNF.FT.D.RLQ.6 X  O Domain Proxy Unsuccessful Relinquishment, responseCode=103 6.7.4.1.1 WINNF.FT.C.DRG.1 --  M Successful Deregistration 6.7.4.1.2 WINNF.FT.D.DRG.2 X  M Domain Proxy Successful Deregistration 6.7.4.2.1 WINNF.FT.C.DRG.3 --  O Deregistration responseCode=102 6.7.4.2.2 WINNF.FT.D.DRG.4 X  O Domain Proxy Deregistration responseCode=102 6.7.4.3.1 WINNF.FT.C.DRG.5 X  O Deregistration responseCode=103 6.8.4.1.1 WINNF.FT.C.SCS.1 X  M Successful TLS connection between UUT and SAS Test Harness 6.8.4.2.1 WINNF.FT.C.SCS.2 X  M TLS failure due to revoked certificate 6.8.4.2.2 WINNF.FT.C.SCS.3 X  M TLS failure due to expired server certificate 6.8.4.2.3 WINNF.FT.C.SCS.4 X  M TLS failure when SAS Test Harness certificate is issued by unknown CA 6.8.4.2.4 WINNF.FT.C.SCS.5 X  M TLS failure when certificate at SAS Test Harness is corrupted 7.1.4.1.1 WINNF.PT.C.HBT.1 X  M UUT RF Transmit Power Measurement Logs WINNF.FT.C.REG.1 2025-11-28T05:04:45.401Z - INFO - WINNF TEST HARNESS RELEASE: 1.0.0.3 - 2018-November-13 2025-11-28T05:04:45.401Z - INFO - the selected test from the user : WINNF.FT.C.REG.1 is starting now 2025-11-28T05:05:18.922Z - INFO - registration request from CBRS : { "registrationRequest": [ { "airInterface": { "radioTechnology": "NR" }, "callSign": "test", "cbsdCategory": "B", "cbsdInfo": { "firmwareVersion": "1.0.0", "hardwareVersion": "1.0.0", "model": "PCW-400", "softwareVersion": "1.0.0", "vendor": "BLiNQ" }, "cbsdSerialNumber": "CBSD1", "fccId": "ROR2003", "userId": "blinq" } ] } 2025-11-28T05:05:18.930Z - INFO - engine sent successfully, the response to CBRS : { "registrationResponse": [ { "cbsdId": "ROR2003Mock-SASCBSD1", "response…

Text truncated - open the document above for the full version.

Report No.: KSCR240700144905 Page: 1 of 53 CCSEM-TRF-001 Rev. 03 Dec 18, 2024 TEST REPORT Application No.: KSCR2407001449AT FCC ID:ROR2002 Applicant:Blinq Networks Inc. Address of Applicant:140 Renfrew Drive, Suite 200, Markham, L3R 6B3, Canada Manufacturer:Blinq Networks Inc. Address of Manufacturer:140 Renfrew Drive, Suite 200, Markham, L3R 6B3, Canada Factory:VVDN Technologies Private Limited Address of Factory:Plot No: CP-07, Sector 8, IMT Manesar, Gurugram, Haryana Equipment Under Test (EUT): EUT Name:PCW-400i Model No.: PCW-400i Standard(s): CBRSA-TS-9001-V1.2.1 WINNF-TS-0122-V1.0.2 FCC 47 CFR Part 96 KDB 940660 D01 V03 Date of Receipt: 2024-07-31 Date of Test: 2025-01-20 to 2025-02-20 Date of Issue: 2025-02-21 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. Report No.: KSCR240700144904 Page: 2 of 53 CCSEM-TRF-001 Rev. 03 Dec 18, 2024 Revision Record VersionDescriptionDateRemark 00Original2025-02-21/ Authorized for issue by: Tested By Eric Liu /Project Engineer Approved By Terry Hou /Reviewer Report No.: KSCR240700144904 Page: 3 of 53 CCSEM-TRF-001 Rev. 03 Dec 18, 2024 2Test Summary ItemStandardTest Case IDResult Domain Proxy Multi-Step registration WINNF-TS-0122- V1.0.2 WINNF.FT.D.REG.2Pass Domain Proxy Single-Step registration for CBSD with CPI signed data WINNF-TS-0122- V1.0.2 WINNF.FT.D.REG.6Pass Domain Proxy Missing Required parameters (responseCode 102) WINNF-TS-0122- V1.0.2 WINNF.FT.D.REG.9Pass Domain Proxy Pending registration (responseCode 200) WINNF-TS-0122- V1.0.2 WINNF.FT.D.REG.11Pass Domain Proxy Invalid parameters (responseCode 103) WINNF-TS-0122- V1.0.2 WINNF.FT.D.REG.13Pass Domain Proxy Blacklisted CBSD (responseCode 101) WINNF-TS-0122- V1.0.2 WINNF.FT.D.REG.15Pass Domain Proxy Unsupported SAS protocol version responseCode 100) WINNF-TS-0122- V1.0.2 WINNF.FT.D.REG.17Pass Domain Proxy Group Error (responseCode 201) WINNF-TS-0122- V1.0.2 WINNF.FT.D.REG.19Pass Unsuccessful Grant responseCode=400 (INTERFERENCE) WINNF-TS-0122- V1.0.2 WINNF.FT.C.GRA.1Pass Unsuccessful Grant responseCode=401 (GRANT_CONFLICT) WINNF-TS-0122- V1.0.2 WINNF.FT.C.GRA.2Pass Domain Proxy Heartbeat Success Case (first Heartbeat Response) WINNF-TS-0122- V1.0.2 WINNF.FT.D.HBT.2Pass Heartbeat responseCode=105 (DEREGISTER) WINNF-TS-0122- V1.0.2 WINNF.FT.C.HBT.3Pass Heartbeat responseCode=501 (SUSPENDED_GRANT) in First Heartbeat Response WINNF-TS-0122- V1.0.2 WINNF.FT.C.HBT.5Pass Heartbeat responseCode=501 (SUSPENDED_GRANT) in Subsequent Heartbeat Response WINNF-TS-0122- V1.0.2 WINNF.FT.C.HBT.6Pass Heartbeat responseCode=502 (UNSYNC_OP_PARAM) WINNF-TS-0122- V1.0.2 WINNF.FT.C.HBT.7Pass Domain Proxy Heartbeat responseCode=500 (TEMINATED_GRANT) WINNF-TS-0122- V1.0.2 WINNF.FT.D.HBT.8Pass Heartbeat Response Absent (First Heartbeat) WINNF-TS-0122- V1.0.2 WINNF.FT.C.HBT.9Pass Heartbeat Response Absent (Subsequent Heartbeat) WINNF-TS-0122- V1.0.2 WINNF.FT.C.HBT.10Pass Successful Grant Renewal in Heartbeat Test Case WINNF-TS-0122- V1.0.2 WINNF.FT.C.HBT.11Pass Domain Proxy Registration Response contains measReportConfig WINNF-TS-0122- V1.0.2 WINNF.FT.D.MES.2Pass Report No.: KSCR240700144904 Page: 4 of 53 CCSEM-TRF-001 Rev. 03 Dec 18, 2024 ItemStandardTest Case IDResult Grant Response contains measReportConfig WINNF-TS-0122- V1.0.2 WINNF.FT.C.MES.3Pass Domain Proxy Heartbeat Response contains measReportConfig WINNF-TS-0122- V1.0.2 WINNF.FT.D.MES.5Pass Domain Proxy Successful Relinquishment WINNF-TS-0122- V1.0.2 WINNF.FT.D.RLQ.2Pass Domain Proxy Unsuccessful Relinquishment, responseCode=102 WINNF-TS-0122- V1.0.2 WINNF.FT.D.RLQ.4Pass Domain Proxy Unsuccessful Relinquishment, responseCode=103 WINNF-TS-0122- V1.0.2 WINNF.FT.D.RLQ.6Pass Domain Proxy Successful Deregistration WINNF-TS-0122- V1.0.2 WINNF.FT.D.DRG.2Pass Domain Proxy Deregistration responseCode=102 WINNF-TS-0122- V1.0.2 WINNF.FT.D.DRG.4Pass Deregistration responseCode=103 WINNF-TS-0122- V1.0.2 WINNF.FT.C.DRG.5Pass Successful TLS connection between UUT and SAS Test Harness WINNF-TS-0122- V1.0.2 WINNF.FT.C.SCS.1 Pass TLS failure due to revoked certificate WINNF-TS-0122- V1.0.2 WINNF.FT.C.SCS.2 Pass TLS failure due to expired server certificate WINNF-TS-0122- V1.0.2 WINNF.FT.C.SCS.3 Pass TLS failure when SAS Test Harness certificate is issue by unknown CA WINNF-TS-0122- V1.0.2 WINNF.FT.C.SCS.4 Pass TLS failure when certificate at the SAS Test Harness is corrupted WINNF-TS-0122- V1.0.2 WINNF.FT.C.SCS.5 Pass UUT RF Transmit Power Measurement WINNF-TS-0122- V1.0.2 WINNF.PT.C.HBT.1Pass SAS Version: 1.0.0.3 The UUT is a CBSD with Domain Proxy. According to the specifications of the manufacturer, it must comply with the requirements of the following standards: Test standards: CBRSA-TS-9001-V1.0.0 CBRS Alliance Certification Test Plan WINNF-TS-0122-V1.0.2 Test and Certification for Citizens Broadband Radio Service (CBRS); Conformance and Performance Test Technical Specification; CBSD/DP as Unit Under Test (UUT) KDB 940660 D01 Part 96 CBRS Eqpt v03 Report No.: KSCR240700144904 Page: 5 of 53 CCSEM-TRF-001 Rev. 03 Dec 18, 2024 3Contents Page 1COVER PAGE...........................................................................................................................................1 2Test Summary..........................................................................................................................................3 3Contents....................................................................................................................................................5 4General Information.................................................................................................................................6 4.1Details of E.U.T.................................................................................................................................6 4.2Description of CBSD/DP Support Features...................................................................................…

Text truncated - open the document above for the full version.

Section 7 Testing data Test name Additional protection levels Specification FCC 47 CFR Part 96 Report reference ID: REP153232 Page 86 of 104 Test data, continued Figure 7.4-19: C. OOB sp. EMI, below 3540 MHz, 1CC 40 MHz, low ch Figure 7.4-20: C. OOB sp. EMI, above 3710 MHz, 1CC 40 MHz, low ch Figure 7.4-21: C. OOB sp. EMI, below 3540 MHz, 1CC 40 MHz, mid ch Figure 7.4-22: C. OOB sp. emissions, above 3710 MHz, 1CC 40 MHz, mid ch Figure 7.4-23: C. OOB sp. EMI, below 3540 MHz, 1CC 40 MHz, high ch Figure 7.4-24: C. OOB sp. EMI, above 3710 MHz, 1CC 40 MHz, high ch Section 7 Testing data Test name Additional protection levels Specification FCC 47 CFR Part 96 Report reference ID: REP153232 Page 87 of 104 Test data, continued Figure 7.4-25: C. OOB sp. EMI, below 3540 MHz, 1CC 60 MHz, low ch Figure 7.4-26: C. OOB sp. EMI, above 3710 MHz, 1CC 60 MHz, low ch Figure 7.4-27: C. OOB sp. EMI, below 3540 MHz, 1CC 60 MHz, mid ch Figure 7.4-28: C. OOB sp. EMI, above 3710 MHz, 1CC 60 MHz, mid ch Figure 7.4-29: C. OOB sp. EMI, below 3540 MHz, 1CC 60 MHz, high ch Figure 7.4-30: C. OOB sp. EMI, above 3710 MHz, 1CC 60 MHz, high ch Section 7 Testing data Test name Additional protection levels Specification FCC 47 CFR Part 96 Report reference ID: REP153232 Page 88 of 104 Test data, continued Figure 7.4-31: C. OOB sp. EMI, below 3540 MHz, 1CC 80 MHz, low ch Figure 7.4-32: C. OOB sp. EMI, above 3710 MHz, 1CC 80 MHz, low ch Figure 7.4-33: C. OOB sp. EMI, below 3540 MHz, 1CC 80 MHz, mid ch Figure 7.4-34: C. OOB sp. EMI, above 3710 MHz, 1CC 80 MHz, mid ch Figure 7.4-35: C. OOB sp. EMI, below 3540 MHz, 1CC 80 MHz, high ch Figure 7.4-36: C. OOB sp. EMI, above 3710 MHz, 1CC 80 MHz, high ch Section 7 Testing data Test name Additional protection levels Specification FCC 47 CFR Part 96 Report reference ID: REP153232 Page 89 of 104 Test data, continued Figure 7.4-37: C. OOB sp. EMI, below 3540 MHz, 1CC 100 MHz, low ch Figure 7.4-38: C. OOB sp. EMI, above 3710 MHz, 1CC 100 MHz, low ch Figure 7.4-39: C. OOB sp. EMI, below 3540 MHz, 1CC 100 MHz, mid ch Figure 7.4-40: C. OOB sp. EMI, above 3710 MHz, 1CC 100 MHz, mid ch Figure 7.4-41: C. OOB sp. EMI, below 3540 MHz, 1CC 100 MHz, high ch Figure 7.4-42: C. OOB sp. EMI, above 3710 MHz, 1CC 100 MHz, high ch Section 7 Testing data Test name Additional protection levels Specification FCC 47 CFR Part 96 Report reference ID: REP153232 Page 90 of 104 Test data, continued Figure 7.4-43: C. OOB sp. EMI, below 3540 MHz, 2CC 10+10 MHz, low ch Figure 7.4-44: C. OOB sp. EMI, above 3710 MHz, 2CC 10+10 MHz, low ch Figure 7.4-45: C. OOB sp. EMI, below 3540 MHz, 2CC 10+10 MHz, mid ch Figure 7.4-46: C. OOB sp. EMI, above 3710 MHz, 2CC 10+10 MHz, mid ch Figure 7.4-47: C. OOB sp. EMI, below 3540 MHz, 2CC 10+10 MHz, high ch Figure 7.4-48: C. OOB sp. EMI, above 3710 MHz, 2CC 10+10 MHz, high ch Section 7 Testing data Test name Additional protection levels Specification FCC 47 CFR Part 96 Report reference ID: REP153232 Page 91 of 104 Test data, continued Figure 7.4-49: C. OOB sp. EMI, below 3540 MHz, 2CC 10+30 MHz, low ch Figure 7.4-50: C. OOB sp. EMI, above 3710 MHz, 2CC 10+30 MHz, low ch Figure 7.4-51: C. OOB sp. EMI, below 3540 MHz, 2CC 10+30 MHz, mid ch Figure 7.4-52: C. OOB sp. EMI, above 3710 MHz, 2CC 10+30 MHz, mid ch Figure 7.4-53: C. OOB sp. EMI, below 3540 MHz, 2CC 10+30 MHz, high ch Figure 7.4-54: C. OOB sp. EMI, above 3710 MHz, 2CC 10+30 MHz, high ch Section 7 Testing data Test name Additional protection levels Specification FCC 47 CFR Part 96 Report reference ID: REP153232 Page 92 of 104 Test data, continued Figure 7.4-55: C. OOB sp. EMI, below 3540 MHz, 2CC 20+20 MHz, low ch Figure 7.4-56: C. OOB sp. EMI, above 3710 MHz, 2CC 20+20 MHz, low ch Figure 7.4-57: C. OOB sp. EMI, below 3540 MHz, 2CC 20+20 MHz, mid ch Figure 7.4-58: C. OOB sp. EMI, above 3710 MHz, 2CC 20+20 MHz, mid ch Figure 7.4-59: C. OOB sp. EMI, below 3540 MHz, 2CC 20+20 MHz, high ch Figure 7.4-60: C. OOB sp. EMI, above 3710 MHz, 2CC 20+20 MHz, high ch Section 7 Testing data Test name Additional protection levels Specification FCC 47 CFR Part 96 Report reference ID: REP153232 Page 93 of 104 Test data, continued Figure 7.4-61: C. OOB sp. EMI, below 3540 MHz, 2CC 20+30 MHz, low ch Figure 7.4-62: C. OOB sp. EMI, above 3710 MHz, 2CC 20+30 MHz, low ch Figure 7.4-63: C. OOB sp. EMI, below 3540 MHz, 2CC 20+30 MHz, mid ch Figure 7.4-64: C. OOB sp. EMI, above 3710 MHz, 2CC 20+30 MHz, mid ch Figure 7.4-65: C. OOB sp. EMI, below 3540 MHz, 2CC 20+30 MHz, high ch Figure 7.4-66: C. OOB sp. EMI, above 3710 MHz, 2CC 20+30 MHz, high ch Section 7 Testing data Test name Additional protection levels Specification FCC 47 CFR Part 96 Report reference ID: REP153232 Page 94 of 104 Test data, continued Figure 7.4-67: C. OOB sp. EMI, below 3540 MHz, 2CC 20+40 MHz, low ch Figure 7.4-68: C. OOB sp. EMI, above 3710 MHz, 2CC 20+40 MHz, low ch Figure 7.4-69: C. OOB sp. EMI, below 3540 MHz, 2CC 20+40 MHz, mid ch Figure 7.4-70: C. OOB sp. EMI, above 3710 MHz, 2CC 20+40 MHz, mid ch Figure 7.4-71: C. OOB sp. EMI, below 3540 MHz, 2CC 20+40 MHz, high ch Figure 7.4-72: C. OOB sp. EMI, above 3710 MHz, 2CC 20+40 MHz, high ch Section 7 Testing data Test name Additional protection levels Specification FCC 47 CFR Part 96 Report reference ID: REP153232 Page 95 of 104 Test data, continued Figure 7.4-73: C. OOB sp. EMI, below 3540 MHz, 2CC 20+60 MHz, low ch Figure 7.4-74: C. OOB sp. EMI, above 3710 MHz, 2CC 20+60 MHz, low ch Figure 7.4-75: C. OOB sp. EMI, below 3540 MHz, 2CC 20+60 MHz, mid ch Figure 7.4-76: C. OOB sp. EMI, above 3710 MHz, 2CC 20+60 MHz, mid ch Figure 7.4-77: C. OOB sp. EMI, below 3540 MHz, 2CC 20+60 MHz, high ch Figure 7.4-78: C. OOB sp. EMI, above 3710 MHz, 2CC 20+60 MHz, high ch Section 7 Testing data Test name Additional protection levels Specification FCC 47 CFR Part 96 Report reference ID: REP153232 Page 96 of 104 Test data, continued Figure 7.4-79: C. OOB sp. EMI, below 3540 MHz, 2CC 40+40 MHz, low ch Figure 7.4-80: C. OOB sp. EMI, above 3710 MHz, 2C…

Text truncated - open the document above for the full version.

Section 7 Testing data Test name General protection levels Specification FCC 47 CFR Part 96 Report reference ID: REP153232 Page 71 of 104 Test data, continued Figure 7.3-265: Cond. sp. EMI, 20 – 37 GHz, 3CC 20+30+40 MHz, mid ch Figure 7.3-266: Cond. B. edge, RBW 1 % EBW, 3CC 20+30+40 MHz, high ch Figure 7.3-267: Conducted band edge, 3CC 20+30+40 MHz, high ch Figure 7.3-268: Cond. sp. EMI, 30 – 3530 MHz, 3CC 20+30+40 MHz, high ch Figure 7.3-269: Cond. sp. EMI, 3.72 – 20 GHz, 3CC 20+30+40 MHz, high ch Figure 7.3-270: Cond. sp. EMI, 20 – 37 GHz, 3CC 20+30+40 MHz, high ch Section 7 Testing data Test name General protection levels Specification FCC 47 CFR Part 96 Report reference ID: REP153232 Page 72 of 104 Test data, continued Figure 7.3-271: Cond. B. E., RBW 1 % EBW, 4CC 10+20+30+40 MHz, low ch. Figure 7.3-272: Conducted band edge, 4CC 10+20+30+40 MHz, low ch Figure 7.3-273: C. sp. EMI, 30 – 3530 MHz, 4CC 10+20+30+40 MHz, low ch Figure 7.3-274: Cond. sp. EMI, 3.72 – 20 GHz, 4CC 10+20+30+40 MHz, low ch Figure 7.3-275: Cond. sp. EMI, 20 – 37 GHz, 4CC 10+20+30+40 MHz, low ch Figure 7.3-276: Cond. B. E., RBW 1 % EBW, 4CC 10+20+30+40 MHz, mid ch. Section 7 Testing data Test name General protection levels Specification FCC 47 CFR Part 96 Report reference ID: REP153232 Page 73 of 104 Test data, continued Figure 7.3-277: Conducted band edge, 4CC 10+20+30+40 MHz, mid ch Figure 7.3-278: C. sp. EMI, 30 – 3530 MHz, 4CC 10+20+30+40 MHz, mid ch Figure 7.3-279: C. sp. EMI, 3.72 – 20 GHz, 4CC 10+20+30+40 MHz, mid ch Figure 7.3-280: Cond. sp. EMI, 20 – 37 GHz, 4CC 10+20+30+40 MHz, mid ch Figure 7.3-281: Cond. B. E., RBW 1 % EBW, 4CC 10+20+30+40 MHz, high ch Figure 7.3-282: Conducted band edge, 4CC 10+20+30+40 MHz, high ch Section 7 Testing data Test name General protection levels Specification FCC 47 CFR Part 96 Report reference ID: REP153232 Page 74 of 104 Test data, continued Figure 7.3-283: C. sp. EMI, 30 – 3530 MHz, 4CC 10+20+30+40 MHz, high ch Figure 7.3-284: C. sp. EMI, 3.72 – 20 GHz, 4CC 10+20+30+40 MHz, high ch Figure 7.3-285: Cond. sp. EMI, 20 – 37 GHz, 4CC 10+20+30+40 MHz, high ch Figure 7.3-286: Cond. B. E., RBW 1 % EBW, 4CC 20+20+20+20 MHz, low ch Figure 7.3-287: Conducted band edge, 4CC 20+20+20+20 MHz, low ch Figure 7.3-288: C. sp. EMI, 30 – 3530 MHz, 4CC 20+20+20+20 MHz, low ch Section 7 Testing data Test name General protection levels Specification FCC 47 CFR Part 96 Report reference ID: REP153232 Page 75 of 104 Test data, continued Figure 7.3-289: C. sp. EMI, 3.72 – 20 GHz, 4CC 20+20+20+20 MHz, low ch Figure 7.3-290: C. sp. EMI, 20 – 37 GHz, 4CC 20+20+20+20 MHz, low ch Figure 7.3-291: Cond. B. E., RBW 1 % EBW, 4CC 20+20+20+20 MHz, mid ch Figure 7.3-292: Conducted band edge, 4CC 20+20+20+20 MHz, mid ch Figure 7.3-293: C. sp. EMI, 30 – 3530 MHz, 4CC 20+20+20+20 MHz, mid ch Figure 7.3-294: C. sp. EMI, 3.72 – 20 GHz, 4CC 20+20+20+20 MHz, mid ch Section 7 Testing data Test name General protection levels Specification FCC 47 CFR Part 96 Report reference ID: REP153232 Page 76 of 104 Test data, continued Figure 7.3-295: C. sp. EMI, 20 – 37 GHz, 4CC 20+20+20+20 MHz, mid ch Figure 7.3-296: Cond. B. E., RBW 1 % EBW, 4CC 20+20+20+20 MHz, high ch Figure 7.3-297: Conducted band edge, 4CC 20+20+20+20 MHz, high ch Figure 7.3-298: C. sp. EMI, 30 – 3530 MHz, 4CC 20+20+20+20 MHz, high ch Figure 7.3-299: C. sp. EMI, 3.72 – 20 GHz, 4CC 20+20+20+20 MHz, high ch Figure 7.3-300: C. sp. EMI, 20 – 37 GHz, 4CC 20+20+20+20 MHz, high ch Section 7 Testing data Test name General protection levels Specification FCC 47 CFR Part 96 Report reference ID: REP153232 Page 77 of 104 Test data, continued Figure 7.3-301: Radiated spurious emissions, 30 – 1000 MHz, 1CC 10 MHz, low ch Figure 7.3-302: Radiated spurious emissions, 1 – 6 GHz, 1CC 10 MHz, low ch Figure 7.3-303: Radiated spurious emissions, 6 – 18 GHz, 1CC 10 MHz, low ch Figure 7.3-304: Radiated spurious emissions, 18 – 26 GHz, 1CC 10 MHz, low ch Figure 7.3-305: Radiated spurious emissions, 26 – 40 GHz, 1CC 10 MHz, low ch Figure 7.3-306: Radiated spurious emissions, 30 – 1000 MHz, 1CC 10 MHz, mid ch 20 25 30 35 40 45 50 55 60 30M 50 60 80 100M 200 300 400 500 800 1G Level in dBμV/m Frequ en cy in H z PR J0096610, RE 30 - 1000 MHz, 1CC 10 MH z, Low channel Preview R esult 1-PK+ FCC Part 96 E-field limits Final_Result QPK Final_Result PK+ FCC Part 96 E-field limits 30 35 40 45 50 55 60 65 70 75 80 85 90 1G 2G 3G 4G 5G 6G Level in dBμV/m Frequ en cy in H z PR J0096610, RE 1 - 6 GH z, 1CC 10 MH z Low channel Preview R esult 1-PK+ FCC Part 96 E-field limits Final_Result PK+ Final_Result R MS 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 6G 8 9 10G 18G Level in dBμV/m Frequ en cy in H z PR J0096610, RE 6 - 18 G Hz, 1CC 10 MH z Low channel Preview R esult 1-PK+ FCC Part 96 E-field limits Final_Result R MS 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 65 18 18.5 19 19.5 20 20.5 21 21.5 22 22.5 23 23.5 24 24.5 25 25.5 26 Level in dBμV/m Frequ en cy in GHz PR J0096610, RE 18 - 26 GH z, 1CC 10 MHz Low channel Preview R esult 1-PK+ FCC Part 96 E-field limits Final_Result PK+ Final_Result R MS 20 25 30 35 40 45 50 55 60 30M 50 60 80 100M 200 300 400 500 800 1G Level in dBμV/m Frequ en cy in H z PR J0096610, RE 30 - 1000 MHz, 1CC 10 MH z, Mid channel Preview R esult 1-PK+ FCC Part 96 E-field limits Final_Result QPK Final_Result PK+ FCC Part 96 E-field limits Section 7 Testing data Test name General protection levels Specification FCC 47 CFR Part 96 Report reference ID: REP153232 Page 78 of 104 Test data, continued Figure 7.3-307: Radiated spurious emissions, 1 – 6 GHz, 1CC 10 MHz, mid ch Figure 7.3-308: Radiated spurious emissions, 6 – 18 GHz,…

Text truncated - open the document above for the full version.