RSD-50800RX2.4G Helicopter

It em# 50800 1 x HELICOPTER 1 x CONTROLLER 1 x A C Charger Adapter Do not modify y our Helicopter! Any changes or modifications to this product are strictly prohibited and will void product warranty. Do not attempt to charge the Helicopter from any other source other than the AC charger provided to charge the Lithium Polymer Battery or you will void the warranty! Any attempts at charging other products with the AC charger are strictly prohibited and will void the warranty! The Lithium Polymer Battery is permanently built-in to the Helicopter. Any attempts to tamper with or remove the Lithium Polymer Battery inside the Helicopter is stictly prohibited and will void the warranty. Do not point the Antenna directly at the Helicopter! Do not use in strong winds, use only in VERY mild conditions! Do not use in rain, snow or around heavy debris! Do not use near electrical lines or high voltage wires or other sources of electricity! Do not use around smoke or flames! Do not use around water and other liquids! Do not use in crowded areas! Do not use around air conditioning! Do not use around air vents! Do not use around ceiling fans! Do not use around large obstacles! Do not use in very small spaces! Do be conscious of changes in your area! Keep moving Rotors and Propellers away from eyes, hands, hair and loose clothing. Always turn off your Helicopter and Controller when not in use. Always remove the batteries from the Controller during storage. Always use new and fresh Alkaline Batteries in Controller for optimal performance. Battery performance will greatly influence flight characteristics. Keep your Instruction Manual in a safe place for future reference. Parental supervision required. The Controller takes one 9V battery (Not included). Industry Canada Notice: Canada only. INS-50800-130108-US This devic e complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These Limits are designed to provide reasonable protection against harmful interference in a residential installation. This generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna - Increase the separation between the equipment and receiver - Connect the equipment to an outlet on a circuit different from that to which the receiver is connected - Consult the dealer or an experienced radio/TV technician for help. 14+ 9V 1.2A Avis d’Industrie Canada Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.      % %   &   $  %        % '  %  &   $ %  $     Industry Canada Notice This device complies with Industry Canada licence-exempt RSS standard(s). 1. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device." 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 1. Slide to open the battery compartment door. 2. Insert the 1 x 9V battery according to the picture shown. Ensure that the + and - polarities match the illustrations inside the battery compartment. 3. Replace the battery compartment door. CHARGING THE HELICOPTER Before ying the Helicopter for the rst time or if you have depleted the charge, you will need to recharge it. A typical charge takes about 60 minutes and allows for approximately 4-6 minutes of ying time. MAKE SURE THE HELICOPTER IS TURNED OFF BEFORE THE RECHARGING CYCLE IS COMMENCED. Note: During charging, both the RED LED on helicopter will light up. The LED will turn to GREEN when the charge is complete. 1) Ensure the Helicopter is turned o. When the helicopter turn o, the LED turned o. 2) Insert the AC charger in to power outlet. 3) Insert the charging wire into the Helicopter charging port which located on the right side of the Helicopter. 4) The charging LED of Helicopter turn on in RED. The Helicopter is charging. It takes 60 minutes to nish the charging. 5) When the charging LED turn to GREEN, the charging is completed. 6) Gently remove the charging wire from the Helicopter. ON/OFF LED MODE SWITCH FORWARD/BACKWARD DIRECTIONAL CONTROL USB charging port in the Helicopter. Insert the USB charging wire the USB charging port in the Helicopter. 1. Turn the controller on by press the ON/OFF Button. The ON/OFF LED w…

Text truncated - open the document above for the full version.

Interactive Toy Concepts Limited January 5, 2013 To: SIEMIC, INC. 775 Montague Expressway Milpitas , CA 95035 USA Dear Sir/Madam, Re: Project and Product Certification Representative Authorization Letter We, ______ Interactive Toy Concepts Limited ___hereby authorize SIEMIC, INC. to act as a Certification Body for certifying for the following project(s): Product Description: 2.4G Helicopter Model name: 50800RX FCC ID: RSD-50800RX We affirm that between SIEMIC and _ Interactive Toy Concepts Limited __, any difference in understanding, including test plan, measurement methods, applicable standards and relevant procedures and processes have been resolved prior to commencement of testing activities. Sincerely, Client’s signature : Client’s name / title : Virginia Yeung / General Manager Contact information / address : Unit 709, 7/F., Tower 2, Cheung Sha Wan Plaza, No. 833 Cheung Sha Wan Rd., Kowloon, Hong Kong

SCS-F19: Confidentiality Request Letter Page 1 of 1 Rev 2.0 Interactive Toy Concepts Limited January 5, 2013 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Confidentiality Request regarding application for certification of FCC ID: RSD-50800RX We hereby request confidential treatment of information accompanying this application as outlined below: - Block Diagram - Operational Description - Schematic The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Client’s signature : Client’s name / title : Virginia Yeung / General Manager Contact information / address : Unit 709, 7/F., Tower 2, Cheung Sha Wan Plaza, No. 833 Cheung Sha Wan Rd., Kowloon, Hong Kong

FCC Certification label location Sample Label location

FCC Certification label Sample FCC ID: RSD-50800RX This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Antenna

Page 1 of 57 FCC ID: RSD -50800RX ACCURATE TECHNOLOGY CO. LTD REPORT NO. ATE20122926 FCC CERTIFICATION On Behalf of Interactive Toy Concepts Limited 2.4G Helicopter Model No.: 50800RX FCC ID: RSD-50800RX Prepared for : Interactive Toy Concepts Limited Address : Unit 709, 7/F., Tower 2, Cheung Sha Wan Plaza, No.833 Cheung Sha Wan Rd., Kowloon, Hong Kong Prepared by : ACCURATE TECHNOLOGY CO. LTD Address : F1, Bldg. A, Changyuan New Material Port, Keyuan Rd. Science & Industry Park, Nanshan, Shenzhen, Guangdong P.R. China Tel: (0755) 26503290 Fax: (0755) 26503396 Report Number : ATE20122926 Date of Test : December 27, 2012-January 5, 2013 Date of Report : January 5, 2013 Page 2 of 57 FCC ID: RSD -50800RX ACCURATE TECHNOLOGY CO. LTD REPORT NO. ATE20122926 TABLE OF CONTENTS Description Page Test Report Certification 1. GENERAL INFORMATION .......................................................................................................... 4 1.1. Description of Device (EUT)....................................................................................................................4 1.2. Description of Test Facility ......................................................................................................................4 1.3. Measurement Uncertainty.........................................................................................................................5 2. MEASURING DEVICE AND TEST EQUIPMENT ..................................................................... 6 3. SUMMARY OF TEST RESULTS................................................................................................... 7 4. FUNDAMENTAL AND HARMONICS RADIATED EMISSION FOR SECTION 15.249(A) 8 4.1. Block Diagram of Test Setup....................................................................................................................8 4.2. The Emission Limit ..................................................................................................................................9 4.3. Configuration of EUT on Measurement ...................................................................................................9 4.4. Operating Condition of EUT ....................................................................................................................9 4.5. Test Procedure ........................................................................................................................................10 4.6. The Field Strength of Radiation Emission Measurement Results ..........................................................11 5. SPURIOUS RADIATED EMISSION FOR SECTION 15.249(D) ............................................. 14 5.1. Block Diagram of Test Setup..................................................................................................................14 5.2. The Emission Limit For Section 15.249(d) ............................................................................................14 5.3. EUT Configuration on Measurement .....................................................................................................15 5.4. Operating Condition of EUT ..................................................................................................................15 5.5. Test Procedure ........................................................................................................................................16 5.6. The Emission Measurement Result ........................................................................................................17 6. BAND EDGES ................................................................................................................................. 20 6.1. The Requirement ....................................................................................................................................20 6.2. EUT Configuration on Measurement .....................................................................................................20 6.3. Operating Condition of EUT ..................................................................................................................20 6.4. Test Procedure ........................................................................................................................................20 6.5. The Measurement Result ........................................................................................................................21 7. AC POWER LINE CONDUCTED EMISSION FOR FCC PART 15 SECTION 15.207(A) .. 23 7.1. Block Diagram of Test Setup..................................................................................................................23 7.2. The Emission Limit ................................................................................................................................23 7.3. Configuration of EUT on Measurement .................................................................................................24 7.4. Operating Condition of EUT ..................................................................................................................24 7.5. Test Procedure ........................................................................................................................................24 7.6. Power Line Conducted Emission Measurement Results ........................................................................25 8. ANTENNA REQUIREMENT........................................................................................................ 26 8.1. The Requirement ....................................................................................................................................26 8.2. Antenna Construction .............................................................................................................................26 APPENDIX I ( TEST CURVES) (30 pages) Page 3 of 57 FCC ID: RSD -50800RX ACCURATE TECHNOLOGY CO. LTD REPORT NO…

Text truncated - open the document above for the full version.

Conducted emissions test Radiated emissions test 9 KHz - 30 MHz Radiated emissions test 30MHz - 1GHz Radiated emissions test > 1GHz