RSNFLEXPRODual-band signal booster for Home and Small office

1 48346 Milmont Dr., Fremont, CA 94538 Phone: 510-770-0469 Fax: 510-996-7250 www.surecall.com Antenna Kitting Information FlexPro Component Prod No. Description Gain/Loss Notes 800MHz 1900MHz Outdoor Antenna CM288W 3dBi 4dBi CM100-L 5dBi 7dBi CM100-S 4dBi 5dBi CM230W 10dBi 10dBi Outdoor Cable CM240-40FN 40Feet 3.98dB 6.52dB CM400-65NN 65Feet 3.89dB 5.43dB 65 Feet or longer Indoor Antenna CM248W 7dBi 10dBi CM222W 3dBi 6dBi Indoor Cable CM240-20FN 20Feet 2.29dB 3.56dB CM400-40NN 40Feet 2.63dB 3.57dB

Dual-Band Wireless Adjustable Signal Booster / Kit Flex Pro Booster, Flex Pro Omni Kit, Flex Pro Panel Kit (FLEX PRO) User Guide INTRODUCTION 2 THEORY OF OPERATION 2 SURECALL FLEX PRO PACKAGES 3 FLEX PRO BOOSTER HARDWARE 4 SUMMARY AND DESCRIPTION OF SAFEGUARD FEATURES 4 SITE SELECTION 5 INSTALLATION INSTRUCTIONS 6 TROUBLESHOOTING 9 FREQUENTLY ASKED QUESTIONS 13 OBTAINING TECHNICAL SUPPORT 13 WARRANTY 14 SPECIFICATIONS 16 SAFETY INFORMATION 17 INTRODUCTION SureCall Flex Pro Home and Office Kit Cellphone-Mate, Inc. Page 2 All rights reserved. Introduction Congratulations on purchasing the SureCall Flex Pro, the finest cellular signal booster available! SureCall adjustable cellular signal boosters and kits from Cellphone-Mate remove frustrations over dropped calls, limited range, and slow data rates by amplifying incoming and outgoing cellular signals in buildings, offices, and homes. The Flex Pro is designed with leading-edge technologies to detect and amplify weak incoming signals your cellular device would otherwise miss and to broadcast a significantly stronger signal back to the cell tower. This guide contains all the information you need to get your SureCall Flex Pro booster system up and running. Theory of Operation The SureCall Flex Pro is a high-quality bidirectional signal booster that boosts cellular signals for areas prone to weak or shadowed cellular coverage. The Flex Pro works with two antennas:  An inside antenna that communicates with your cell phone.  An outside antenna that communicates with the cell tower. Signals sent from a cell tower are received by the outside antenna, amplified by the booster and then sent to your phone via the inside antenna. When your phone transmits, the signal is sent to the inside antenna, and then sent to the cell tower via the outside antenna. Some cell signal is required for the Flex Pro to enhance cellular signal coverage. The weakest cell signal for the Flex Pro to work is low -100dBm to high -90dBm. dBm is an abbreviation for the power ratio in decibels of the radio power per one milliwatt. To measure your existing cell signal on an Apple iPhone, dial *3001#12345#*and press Call. In the top-left corner, a number appears instead of bars. For Android devices, you can download several apps to measure exact signal strength. Look up check real signal strength to find a cell signal measurement app. INTRODUCTION SureCall Flex Pro Home and Office Kit Cellphone-Mate, Inc. Page 3 All rights reserved. SureCall Flex Pro Packages Flex Pro - Antenna Kitting Information Component Product Number (Description) Gain/Loss Notes 800 MHz 1900 MHz Outdoor Antennas* CM288W 3 dBi 4 dBi CM100-L 5 dBi 7 dBi CM100-S 4 dBi 5 dBi CM230W 10 dBi 10 dBi Outdoor Cables* CM240-40FN (40 feet) –3.98 dB –6.52 dB CM400-65NN (65 feet) –3.89 dB –5.43 dB 65 feet or longer Indoor Antennas* CM248W 7 dBi 10 dBi CM222W 3 dBi 6 dBi Indoor Cables* CM240-20FN (20 feet) –2.29 dB –3.56 dB CM400-40NN (40 feet) –2.63 dB –3.57 dB * All equivalent antennas and cables are suitable for use with the Flex Pro booster. Note: For the signal booster to work, the following items are required:  Outside antenna  Cable for connecting the outside antenna to the booster  Signal booster  Inside antenna  Cable for connecting the inside antenna to the booster  Power supply Warning: Unauthorized antennas, cables, and/or coupling devices are prohibited by FCC new rules. Please contact FCC for details: 1-888-CALL-FCC. Changes or modifications not expressly approved by Cellphone-Mate could void the user’s authority to operate the equipment. INTRODUCTION SureCall Flex Pro Home and Office Kit Cellphone-Mate, Inc. Page 4 All rights reserved. Flex Pro Booster Hardware The following figure shows the key hardware components on the Flex Pro cellular signal booster. Refer to this figure as you install your SureCall Flex Pro components. Summary and Description of Safeguard Features This device is equipped with all the safeguard features required by FCC new rules to ensure no interference is created to affect the cell tower: AGC, automatic shutdown, Dual RSSI monitoring, automatic silence, and more. PCS- 1900 Dial Alert LED Outdoor Antenna Connector (not shown) Indoor Antenna Connector Power Connector Power LED Alert LED Cellular- 800 Dial Digital Interface INSTALLATION SureCall Flex Pro Home and Office Kit Cellphone-Mate, Inc. Page 5 All rights reserved. Unpack all package contents and check for damage. For missing or damaged items, contact your reseller. Keep the carton and packing material to store the product or if you need to return it. Site Selection For optimum performance, select a location for your booster that:  Provides the best signal strength possible. To measure your existing cell signal on an Apple iPhone, dial *3001#12345#*and press Call. In the top- left corner, a number appears instead of bars. For Android devices, you can download several apps to measure exact signal strength. Look up “check real signal strength“ to find a cell signal measurement app.  Avoids areas where wireless signals can be blocked or reflected by buildings, walls, trees, hills, and other terrain features. This can result in low signal strength.  Is not close to energy-efficient windows, which can affect signal penetration into a home or office. Note: The cell phone tower site in relation to the location where you install your booster also determines signal strength. Although cell phone providers try to place towers for maximum coverage, local ordinances and terrain features can restrict tower locations, which can limit signal strength at your location. INSTALLATION SureCall Flex Pro Home and Office Kit Cellphone-Mate, Inc. Page 6 All rights reserved. Installation Instructions The Flex Pro signal booster is suited for installation in a building or home. Step 1. Connect the Outside Antenna 1. Mount the fiberglass antenna in an outside mounting location that:  Has at least a 12-inch radius clear of obstructions and other …

Text truncated - open the document above for the full version.

48346 Milmont Drive Fremont, CA 94538 Phone: 510-770-0469 Fax: 510-996-7250 www.cellphone-mate.com FCC Authorization 9 th December, 2013 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To Whom It May Concern: We, Cellphone-mate , the undersigned, hereby authorize CKC Certification Services, LLC to act on our behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by CKC Certification Services, LLC on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). This authorization is valid until further written notice from the applicant. Sincerely yours, Hongtao Zhan, CEO Cellphone-Mate Inc. 1888 365 6283 ext. 301 48346 Milmont Drive Fremont, CA 94538 Phone: 510-770-0469 Fax: 510-996-7250 www.cellphone-mate.com

48346 Milmont Drive Fremont, CA 94538 Phone: 510-770-0469 Fax: 510-996-7250 www.cellphone-mate.com FCC Confidential Authorization 20th January, 2014 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: RSNFLEXPRO In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, Cellphone-mate hereby requests long- term confidential treatment of information accompanying this application as outlined below:  Block Diagram  Schematics  Operation Description  Parts list The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely, Sincerely Yours, Hongtao Zhan, CEO Cellphone-Mate Inc. 1888 365 6283 ext. 301

Tune up procedure: There is no need for tune up for this product when in production.

1 FCC§1.1307（b）(1)&§2.1091-RF EXPOSURE 1.1 Applicable Standard According to§1.1310 and §2.1091(Mobile Devices)RF exposure is calculated. Limits for General Population/Uncontrolled Exposure Frequency Range (MHz) Power Density (mW/cm²) Limits for General Population/Uncontrolled Exposure 0.3-1.34 *(100) 1.34-30 *(180/f²) 30-300 0.2 300–1,500 f/1500 1,500–100,000 1 Note: f= frequency in MHz *=Plane-wave equivalent power density 1.2 MPE Prediction 1.2.1 Calculation of MPE at 20 cm distance, Equation from OET Bulletin 65, Edition 97-01 S=PG/4πR² Where: S=power density P=power input to antenna G= maximum power gain of the antenna in the direction of interest relative to an isotropic radiator, subtract antenna’s cable loss, (result is in numeric form) R=distance to the center of radiation of the antenna (20cm in the following calculation) 1.2.2 Calculation formula of G（numeric ) G (numeric)=10 {Maximum Antenna Gain dBi () -Cable LossdB () } 1 10 Where: G（numeric）= Maximum power gain of the antenna in the direction of interest relative to an isotropic radiator, subtract antenna’s cable loss, (result is converted from decibel into numeric form with above equation) 1.3 Test Result Outdoor Antenna Outdoor Antenna Outdoor Antenna Gain At 1900MHz(dBi) At 800MHz(dBi) CM100-S 5 4 CM230W 10 10 CM288W 4 3 CM100-L 7 5 MAX GAIN 10 10 Outdoor Cable Outdoor Cable Outdoor Cable Loss At 1900MHz(dB) At 800MHz(dB) CM240-40FN 40Feet 6.52 3.98 CM400-65NN 65Feet 5.43 3.89 MIN LOSS 5.43 3.89 Indoor Antenna Indoor Antenna Indoor Antenna Gain At 1900MHz(dBi) At 800MHz(dBi) CM222W 6 3 CM248W 10 7 MAX GAIN 10 7 Indoor Cable Indoor Cable Indoor Cable Loss At 1900MHz(dB) At 800MHz(dB) CM240-20FN 20Feet 3.56 2.29 CM400-40NN 40Feet 3.57 2.63 MIN LOSS 3.56 2.29 Cellular Band UL: Maximum peak output power at antenna input terminal(dBm): 20.00 Maximum peak output power at antenna input terminal(mW): 100.00 Prediction distance(cm): 20 Prediction frequency(MHz): 830.00 Maximum Antenna Gain (dBi): 10 Cable Loss(dB): 3.89 G（numeric）: 4.08 Power density at predication frequency and distance(mW/cm²): 0.0813 MPE limit for uncontrolled exposure at predication frequency(mW/cm²): 0.5533 Cellular Band DL: Maximum peak output power at antenna input terminal(dBm): 3.80 Maximum peak output power at antenna input terminal(mW): 2.40 Prediction distance(cm): 20 Prediction frequency(MHz): 881.00 Maximum Antenna Gain (dBi): 7 Cable Loss(dB): 2.29 G（numeric）: 2.96 Power density at predication frequency and distance(mW/cm²): 0.0014 MPE limit for uncontrolled exposure at predication frequency(mW/cm²): 0.5873 PCS Band UL: Maximum peak output power at antenna input terminal(dBm): 22.40 Maximum peak output power at antenna input terminal(mW): 173.78 Prediction distance(cm): 20 Prediction frequency(MHz): 1865.00 Maximum Antenna Gain (dBi): 10 Cable Loss(dB): 5.43 G（numeric）: 2.86 Power density at predication frequency and distance(mW/cm²): 0.0991 MPE limit for uncontrolled exposure at predication frequency(mW/cm²): 1.0000 PCS Band DL: Maximum peak output power at antenna input terminal(dBm): -1.20 Maximum peak output power at antenna input terminal(mW): 0.76 Prediction distance(cm): 20 Prediction frequency(MHz): 1956.00 Maximum Antenna Gain (dBi): 10 Cable Loss(dB): 3.56 G（numeric）: 4.41 Power density at predication frequency and distance(mW/cm²): 0.0007 MPE limit for uncontrolled exposure at predication frequency(mW/cm²): 1.0000

This report contains a total of 51 pages and may be reproduced in full only. Partial reproduction may only be done with the written consent of CKC Laboratories, Inc. Cellphone-Mate, Inc. ADDENDUM TO TEST REPORT 94297 Fixed Wideband Consumer Signal Boosters Model: Flex Pro Tested To The Following Standards: FCC Part 20, Section 20.21 Report No.: 94297-9A Date of issue: December 16, 2013 We strive to create long-term, trust based relationships by providing sound, adaptive, customer first testing services. We embrace each of our customers’ unique EMC challenges, not as an interruption to set processes, but rather as the reason we are in business. Page 2 of 51 Report No.: 94297-9A TABLE OF CONTENTS Administrative Information .......................................................................................................................... 3 Test Report Information ............................................................................................................................................ 3 Revision History ......................................................................................................................................................... 3 Report Authorization ................................................................................................................................................. 3 Test Facility Information ............................................................................................................................................ 4 Software Versions ...................................................................................................................................................... 4 Site Registration & Accreditation Information .......................................................................................................... 4 Summary of Results ................................................................................................................................................... 5 Conditions During Testing.......................................................................................................................................... 5 Equipment Under Test ............................................................................................................................................... 6 Peripheral Devices ..................................................................................................................................................... 6 FCC Part 20 .................................................................................................................................................... 7 FCC 20.21(e)(8)(i)(A) Noise Limit ............................................................................................................................... 7 FCC 20.21(e)(8)(i)(B) Bidirectional Capability Power Limit ...................................................................................... 14 FCC 20.21(e)(8)(i)(C) Booster Gain Limit .................................................................................................................. 25 FCC 20.21(e)(8)(i)(E) Out of Band Emission Limits ................................................................................................... 28 FCC 20.21(e)(8)(i)(F) Intermodulation Limits ........................................................................................................... 36 FCC 20.21(e)(8)(i)(I) Uplink Inactivity ....................................................................................................................... 40 FCC 20.21(e)(8)(ii)(A) Anti Oscillation ...................................................................................................................... 43 Page 3 of 51 Report No.: 94297-9A ADMINISTRATIVE INFORMATION Test Report Information REPORT PREPARED FOR: REPORT PREPARED BY: Cellphone-Mate, Inc. 48346 Milmont Drive Fremont, CA 94538 Dianne Dudley CKC Laboratories, Inc. 5046 Sierra Pines Drive Mariposa, CA 95338 Representative: Dennis Findley Project Number: 94297 DATE OF EQUIPMENT RECEIPT: October 31, 2013 DATE(S) OF TESTING: October 31- November 4, 2013 Revision History Original: Testing of Fixed Wideband Consumer Signal Boosters, Flexpro to FCC Part 20, Section 20.21. Addendum A: Additional testing clarification was added to test conditions throughout the report as well as adding comments for clarification under plots. Report Authorization The test data contained in this report documents the observed testing parameters pertaining to and are relevant for only the sample equipment tested in the agreed upon operational mode(s) and configuration(s) as identified herein. Compliance assessment remains the client’s responsibility. This report may not be used to claim product endorsement by A2LA or any government agencies. This test report has been authorized for release under quality control from CKC Laboratories, Inc. Steve Behm Director of Quality Assurance & Engineering Services CKC Laboratories, Inc. Page 4 of 51 Report No.: 94297-9A Test Facility Information Our laboratories are configured to effectively test a wide variety of product types. CKC utilizes first class test equipment, anechoic chambers, data acquisition and information services to create accurate, repeatable and affordable test results. TEST LOCATION(S): CKC Laboratories, Inc. 110 Olinda Place Brea, CA 92823 Software Versions CKC Laboratories Proprietary Software Version EMITest Emissions 5.00.14 Immunity 5.00.07 Site Registration & Accreditation Information Location CB # TAIWAN CANADA FCC JAPAN Brea A US0060 SL2-IN-E-1146R 3082D-1 90473 A-0147 Page 5 of 51 Report No.: 94297-9A SUMMARY OF RESULTS Standard / Specification: FCC Part 20 Description Test Procedure/Method Results Noise Limit - Transmit off FCC Part 20.21(e )(8)(i)(A) / 7.7 Pass Bidirectional Capability D Power Limit FCC Part 20.21(e)(8)(i)(B) / 7.2 Pass Booster Gain Limits FCC Part…

Text truncated - open the document above for the full version.

This report contains a total of 28 pages and may be reproduced in full only. Partial reproduction may only be done with the written consent of CKC Laboratories, Inc. Cellphone-Mate, Inc. TEST REPORT FOR Fixed Wideband Consumer Signal Boosters Model: Flex Pro Tested To The Following Standard: FCC Part 22H Report No.: 94297-12 Date of issue: November 15, 2013 This test report bears the accreditation symbol indicating that the testing performed herein meets the test and reporting requirements of ISO/IEC 17025 under the applicable scope of EMC testing for CKC Laboratories, Inc. We strive to create long-term, trust based relationships by providing sound, adaptive, customer first testing services. We embrace each of our customers’ unique EMC challenges, not as an interruption to set processes, but rather as the reason we are in business. Page 2 of 28 Report No.: 94297-12 TABLE OF CONTENTS Administrative Information ........................................................................................................................................... 3 Test Report Information ............................................................................................................................................ 3 Report Authorization ................................................................................................................................................. 3 Test Facility Information ............................................................................................................................................ 4 Software Versions ...................................................................................................................................................... 4 Site Registration & Accreditation Information .......................................................................................................... 4 Summary of Results ................................................................................................................................................... 5 Conditions During Testing.......................................................................................................................................... 5 Equipment Under Test ............................................................................................................................................... 6 Peripheral Devices ..................................................................................................................................................... 6 FCC Part 22H .................................................................................................................................................................. 7 2.1049(I) Occupied Bandwidth .................................................................................................................................. 7 22.917(a) / 2.1051 Spurious Emissions at Antenna Terminal .................................................................................. 16 22.917(a) / 2.1053 Field Strength of Spurious Radiation ........................................................................................ 22 Supplemental Information .......................................................................................................................................... 27 Measurement Uncertainty ...................................................................................................................................... 27 Emissions Test Details .............................................................................................................................................. 27 Page 3 of 28 Report No.: 94297-12 ADMINISTRATIVE INFORMATION Test Report Information REPORT PREPARED FOR: REPORT PREPARED BY: Cellphone-Mate, Inc. 48346 Milmont Drive Fremont, CA 94538 Dianne Dudley CKC Laboratories, Inc. 5046 Sierra Pines Drive Mariposa, CA 95338 Representative: Dennis Findley Project Number: 94297 DATE OF EQUIPMENT RECEIPT: October.31, 2013 DATE(S) OF TESTING: October 31 - November 1, 2013 Report Authorization The test data contained in this report documents the observed testing parameters pertaining to and are relevant for only the sample equipment tested in the agreed upon operational mode(s) and configuration(s) as identified herein. Compliance assessment remains the client’s responsibility. This report may not be used to claim product endorsement by A2LA or any government agencies. This test report has been authorized for release under quality control from CKC Laboratories, Inc. Steve Behm Director of Quality Assurance & Engineering Services CKC Laboratories, Inc. Page 4 of 28 Report No.: 94297-12 Test Facility Information Our laboratories are configured to effectively test a wide variety of product types. CKC utilizes first class test equipment, anechoic chambers, data acquisition and information services to create accurate, repeatable and affordable test results. TEST LOCATION(S): CKC Laboratories, Inc. 110 Olinda Place Brea, CA 92823 Software Versions CKC Laboratories Proprietary Software Version EMITest Emissions 5.00.14 Immunity 5.00.07 Site Registration & Accreditation Information Location CB # TAIWAN CANADA FCC JAPAN Brea A US0060 SL2-IN-E-1146R 3082D-1 90473 A-0147 Page 5 of 28 Report No.: 94297-12 SUMMARY OF RESULTS Standard / Specification: FCC Part 22H Description Test Procedure/Method Results Occupied Bandwidth FCC Part 22H / 2.1049(I) Pass Spurious Emissions at Antenna Terminal FCC Part 22H § 22.917(a) / 2.1051 Pass Field Strength of Spurious Radiation FCC Part 22H § 22.917(a) / 2.1053 Pass Conditions During Testing This list is a summary of the conditions noted for or modifications made to the equipment during testing. Summary of Conditions None Page 6 of 28 Report No.: 94297-12 EQUIPMENT UNDER TEST (EUT) EQUIPMENT UNDER TEST Fixed Wideband Consumer Signal Boosters Manuf: Cellphone-Mate, Inc. Model: Flex Pro Serial: 1 PERIPH…

Text truncated - open the document above for the full version.

This report contains a total of 27 pages and may be reproduced in full only. Partial reproduction may only be done with the written consent of CKC Laboratories, Inc. Cellphone-Mate, Inc. TEST REPORT FOR Fixed Wideband Consumer Signal Boosters Model: Flex Pro Tested To The Following Standards: FCC Part 24E Report No.: 94297-13 Date of issue: November 18, 2013 This test report bears the accreditation symbol indicating that the testing performed herein meets the test and reporting requirements of ISO/IEC 17025 under the applicable scope of EMC testing for CKC Laboratories, Inc. We strive to create long-term, trust based relationships by providing sound, adaptive, customer first testing services. We embrace each of our customers’ unique EMC challenges, not as an interruption to set processes, but rather as the reason we are in business. Page 2 of 27 Report No.: 94297-13 TABLE OF CONTENTS Administrative Information .......................................................................................................................... 3 Test Report Information ............................................................................................................................................ 3 Report Authorization ................................................................................................................................................. 3 Test Facility Information ............................................................................................................................................ 4 Software Versions ...................................................................................................................................................... 4 Site Registration & Accreditation Information .......................................................................................................... 4 Summary of Results ................................................................................................................................................... 5 Conditions During Testing.......................................................................................................................................... 5 Equipment Under Test ............................................................................................................................................... 6 Peripheral Devices ..................................................................................................................................................... 6 FCC Part 24E .................................................................................................................................................. 7 2.1049(I) Occupied Bandwidth .................................................................................................................................. 7 FCC 24.238(a) / 2.1051 Spurious Emissions at Antenna Terminal ........................................................................... 16 FCC 24.328(a) / 2.1053 Field Strength of Spurious Radiation.................................................................................. 21 Supplemental Information .......................................................................................................................... 26 Measurement Uncertainty ...................................................................................................................................... 26 Emissions Test Details .............................................................................................................................................. 26 Page 3 of 27 Report No.: 94297-13 ADMINISTRATIVE INFORMATION Test Report Information REPORT PREPARED FOR: REPORT PREPARED BY: Cellphone-Mate, Inc. 48346 Milmont Drive Fremont, CA 94538 Dianne Dudley CKC Laboratories, Inc. 5046 Sierra Pines Drive Mariposa, CA 95338 Representative: Dennis Findley Project Number: 94297 DATE OF EQUIPMENT RECEIPT: October 31, 2013 DATE(S) OF TESTING: October 31 -November 4, 2013 Report Authorization The test data contained in this report documents the observed testing parameters pertaining to and are relevant for only the sample equipment tested in the agreed upon operational mode(s) and configuration(s) as identified herein. Compliance assessment remains the client’s responsibility. This report may not be used to claim product endorsement by A2LA or any government agencies. This test report has been authorized for release under quality control from CKC Laboratories, Inc. Steve Behm Director of Quality Assurance & Engineering Services CKC Laboratories, Inc. Page 4 of 27 Report No.: 94297-13 Test Facility Information Our laboratories are configured to effectively test a wide variety of product types. CKC utilizes first class test equipment, anechoic chambers, data acquisition and information services to create accurate, repeatable and affordable test results. TEST LOCATION(S): CKC Laboratories, Inc. 110 Olinda Place Brea, CA 92823 Software Versions CKC Laboratories Proprietary Software Version EMITest Emissions 5.00.14 Immunity 5.00.07 Site Registration & Accreditation Information Location CB # TAIWAN CANADA FCC JAPAN Brea A US0060 SL2-IN-E-1146R 3082D-1 90473 A-0147 Page 5 of 27 Report No.: 94297-13 SUMMARY OF RESULTS Standard / Specification: FCC Part 24E Description Test Procedure/Method Results Occupied Bandwidth FCC Part 24E / 2.1049(I) Pass Spurious Emissions at Antenna Terminal FCC Part 24E § 24.238(a) / 2.1051 Pass Field Strength of Spurious Radiation FCC Part 24E § 24.238(a) / 2.1053 Pass Conditions During Testing This list is a summary of the conditions noted for or modifications made to the equipment during testing. Summary of Conditions None Page 6 of 27 Report No.: 94297-13 EQUIPMENT UNDER TEST (EUT) EQUIPMENT UNDER TEST Fixed Wideband Consumer Signal Boosters Manuf: Cellphone-Mate, Inc. Model: Flex Pro Serial: 1 PERIPHERA…

Text truncated - open the document above for the full version.