RYLH145001Wireless Mouse

User Manual Mouse Operating steps： The wireless mouse uses two AA batteries. a) Open the battery cover at the bottom of the mouse. b) Insert the two AA batteries. c) Replace the cover after the batteries are installed. 2、 Plug in the receiver to USB port on your computer. When receiver is ready, LED is on. 3、 Press three buttons of the mouse (left/right/roller) at the same time to change the sensor speed DPI. (1000DPI-2000DPI.) 4、 Press the button at the bottom of the mouse, new ID code setting has been completed to avoid another user interference. 5、 Sensor 4 stages of batteries consuming design can offer more than two months of normal office use. 1)Work stop： stop flash 。 2)Stand by(1)：flash quickly。 3)Stand by(2)：flash quickly。 4)Sleeping： flash slowly。 EUT DESCRIPTION Model no H145001 USB WEBCAN Type □Wired ■ Wireless IC EV656A51H Interface Conductive □Cable □Receiver Port type □ PS/2 , ■ USB , □ U+P Cable length (mm) Frequency 27.045MHz Operating current 25mA Supply Voltage 2.0V – 3.0 V Sensor speed DPI 1000DPI – 2000DPI DPI LED Color Dimension (mm) 90*50*36.50mm Weight 58g±5g Operation Temperature -30°C ~ 40°C Storage temperature -40°C to 60°C Storage Humidity 90% RH or less System requirement ■ PC ■ MAC Warranty Five years Certification ■CE ■FCC □BSMI □Other ____________________ Warning: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications to this unit not expressly approved by the party responsible for compliance will void the user’s authority to operate the equipment. Any change to the equipment will void FCC grant. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help.

AND5030 27.045MHz

External Photos EUT- Front View EUT- Back View

ID Label FCC ID Label Label Location Information Specifications : Text is Black or white in color and is left justified. Labels are printed in indelible ink on permanent adhesive backing or silk-screened onto the EUT or shall be affixed at a conspicuous location on the EUT. FCC ID Label Location FCC ID: RYLH145001 F CC ID : RYLH14 500 1

Internal Photos EUT – Uncovered View EUT- Main PCB Top View EUT- Main PCB Bottom View EUT- Control PCB Top View EUT- Control PCB Bottom View

Wireless Mouse Transmitter Circuit Description a. IC-ANDS5030：IC-ANDS5030 is the integration of wireless controlling IC and optical IC. The optical part of ANDS5030 transforms the image of the mouse movement to the electronic signal, and then send to the controlling IC; the signal transmits from the antenna after modulated to a frequency of 27.045 MHz. b. The clock signal of IC-ANDS5030 is controlled by clock of oscillating controller. c. When the optical part of IC－ANDS5030 is working, the MCU will output the controlling signal Q6 from the PIN 2 to control the brightness of D1. d. The operating voltage of IC-ANDS5030 is 3.0V.

Note: This test report is for the customer shown above and their specific product only. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratory Corp. (Shenzhen). This report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST or any agency of the Federal Government. FCC PART 15.227 EMI MEASUREMENT AND TEST REPORT For DynaPoint (Dong Guan) Inc. The Sixth Industrial Park, Shangsha, South Area ChangAn, DongGuan, GuangDong, China 523880 FCC ID: RYLH145001 This Report Concerns: Original Report Equipment Type: Wireless Mouse Test Engineer: Henry Yang Report No.: RSZ07021405 Test Date: 2007-03-07 to 2007-03-19 Report Date: 2007-03-22 Reviewed By: EMC Manager: Boni Baniqued Prepared By: Bay Area Compliance Laboratory Corp. (Shenzhen) 6/F, the 3rd Phase of WanLi Industrial Building, ShiHua Road, FuTian Free Trade Zone Shenzhen, Guangdong, China Tel: +86-755-33320018 Fax: +86-755-33320008 DynaPoint (Dong Guan) Inc. FCC ID: RYLH145001 Report #: RSZ07021405 Page 2 of 12 FCC PART 15.227 Report TABLE OF CONTENTS GENERAL INFORMATION.......................................................................................................................................3 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) .....................................................................................3 OBJECTIVE...................................................................................................................................................................3 RELATED SUBMITTAL(S)/GRANT(S).............................................................................................................................3 TEST METHODOLOGY..................................................................................................................................................3 TEST FACILITY.............................................................................................................................................................3 SYSTEM TEST CONFIGURATION ..........................................................................................................................4 JUSTIFICATION.............................................................................................................................................................4 EUT EXERCISE SOFTWARE..........................................................................................................................................4 SPECIAL ACCESSORIES.................................................................................................................................................4 SCHEMATICS AND BLOCK DIAGRAM............................................................................................................................4 EQUIPMENT MODIFICATIONS.......................................................................................................................................4 CONFIGURATION OF TEST SETUP.................................................................................................................................5 BLOCK DIAGRAM OF TEST SETUP................................................................................................................................5 SUMMARY OF TEST RESULTS ...............................................................................................................................6 §15.203 - ANTENNA REQUIREMENT......................................................................................................................7 STANDARD APPLICABLE..............................................................................................................................................7 §15.205, §15.209, §15.227(A) - RADIATED EMISSIONS TEST ..............................................................................8 STANDARD APPLICABLE..............................................................................................................................................8 MEASUREMENT UNCERTAINTY....................................................................................................................................8 EUT SETUP..................................................................................................................................................................8 EMI TEST RECEIVER SETUP.........................................................................................................................................9 TEST EQUIPMENT LIST AND DETAILS...........................................................................................................................9 CORRECTED AMPLITUDE & MARGIN CALCULATION...................................................................................................9 TEST RESULTS SUMMARY............................................................................................................................................9 TEST DATA................................................................................................................................................................10 §15.227(B) – OUT OF BAND EMISSIONS ..............................................................................................................11 STANDARD APPLICABLE............................................................................................................................................11 TEST EQUIPMENT LIST AND DETAILS.........................................................................................................................11 TEST DATA................................................................................................................................................................11 DynaPoint (Dong Guan) Inc. FCC ID: RYLH145001 Report #: RSZ07021405 Page 3 of 12 FCC PART 15.227 Report GENERAL INFORMATI…

Text truncated - open the document above for the full version.

Test Setup Photos Radiated Emission (Below 30 MHz) - Front View Radiated Emission (Below 30 MHz) - Rear View Radiated Emissions (30-1000 MHz) - Front View Radiated Emissions (30-1000 MHz) - Rear View