S9NZB260AZigBee Module

SPZB260 ZigBee Module ZigBee RF MODULE BLOCK DIAGRAM

NOTICE: The results of tests and checks reported in this Test Report refer exclusively to the samples tested and described in the Report itself. This report shall not be reproduced partially or in its entirety without the written approval of IMQ S.p.A. IMQ S.p.A. - Via Quintiliano, 43 – I-20138 MILANO T E L E C O M M U N I C A T I O N S & T E L E M A T I C S F O R T R A N S P O R T S L A B O R A T O R Y Telecommunications & Telematics for Transports Lab. TEST REPORT Ref. No. ARSH00131/1 Date: 2007-09-25 According with: FCC Rules: Code of Federal Regulations (CFR) no. 47 - PART 15 – UNLICENSED MODULAR TRANSMITTER APPROVAL PUBLIC NOTICE: DA 00-1407 PRODUCT :ZigBee module general purpose TESTED MODEL :SPZB260 FCC ID :S9NZB260A APPLICANT : STMicroelectronics – Centro Direzionale Colleoni – Palazzo Andromeda 3 – I-20044 Agrate Brianza (MI) - ITALY MANUFACTURER: STMicroelectronics – Centro Direzionale Colleoni – Palazzo Andromeda 3 – I-20044 Agrate Brianza (MI) - ITALY TRADEMARK : STMicroelectronics OTHER INFORMATION Testing dates : 2007-07-19 ÷ 2007-07-20 Tested samples No.:1 Testing Laboratory : IMQ S.p.A. Via Quintiliano, 43 I-20138 MILANO Prepared by: R. Colombo (EMC and R&TTE Lab deputy) Signature: Revision Sheet Release No. Date Revision Description Rev. 0 2007-09-25 First emission TT&T Laboratory Test Report No. ARSH00131/1 Date: 2007-09-25 page 2 of 3 T E L E C O M M U N I C A T I O N S & T E L E M A T I C S F O R T R A N S P O R T S L A B O R A T O R Y REFERENCE STANDARDS According to : PUBLIC NOTICE : DA 00-1407 Part 15 Unlicensed Modular Transmitter Approval Released : June 26, 2000 MODULE-TYPE DEVICE APPROVAL OPTIONS: Modular Approval (MA) Limited Modular Approval (LMA) REQUIREMENTS The following requirements are fulfilled: 1) The modular transmitter must have its own RF shielding: The RF module fulfils the emission requirements of the FCC rules without additional shielding. 2) The modular transmitter must have buffered modulation/data inputs: The module has a memory management unit inside of the IC. The processor interfacing with the external application by means general purpose I/O ( GPIO) , Uart, SPI. The processor interfaces also the RF part of the module exchanging data and command with it. Inside the processor a flash memory is available to download the customer application and the ZigBee profiles. 3) The modular transmitter must have its own power supply regulation: The IC contains an own voltage regulation. In case of changes in the supply voltage VCC (for example caused by temperature changes or other effects), the internal voltage will be stabilized. 4) The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204: The end-user product will be installed in such a manner that only the authorized antenna is used. 5) The modular transmitter must be tested in a stand-alone configuration: The RF module was tested in a stand-alone configuration. TT&T Laboratory Test Report No. ARSH00131/1 Date: 2007-09-25 page 3 of 3 T E L E C O M M U N I C A T I O N S & T E L E M A T I C S F O R T R A N S P O R T S L A B O R A T O R Y 6) The modular transmitter must be labelled with its own FCC ID number: The RF module will be labelled with its own FCC ID number. When the module is installed inside the end-product, the label is not visible. The end- user/integrator is instructed how to apply the exterior label. 7) The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements: The EUT is compliant with all applicable FCC rules. Detail instructions are given in the product Users Guide. 8) The modular transmitter must comply with any applicable RF exposure requirements. •Maximum measured power output: 3,08 mW (4,89 dBm) •Maximum antenna gain: 0,6 dBi = numeric gain 1,148 (see also FCC test report) Maximum permissible exposure defined in 47 CFR 1.1310: 1 mW/cm². The distance from the EUT's transmitting antenna where the exposure level reaches the maximum permitted level is calculated using the general equation: S = P*G / 4JR² S max = 1 mW/cm² P= 4,89 mW G= 0,6 dBi = 1,148 (numeric gain) R= distance in cm Solving for R, the 1 mW/cm² limit is reached in a distance of 0,53 cm to the transmitting antenna. The RF module operates at low power level so it does not exceed the Commission’s RF exposure guidelines limits; furthermore, Spread spectrum transmitters operate according to the Section 15.247 are categorically excluded from routine environmental evaluation. Special requirement for Limited Modular Approval: The customer retain control over the final installation of the RF module. The EUT is approved only for use when installed in device produced by the manufacturer (Grantee).

SPZB260 ZigBee Module ZigBee RF MODULE OPERATIONAL DESCRIPTION SPZB260 is a ZigBee module optimized for embedded applications. It enables OEMs to easily add short-range radio link between electronic devices. The module is based on SN260 ZigBee Netework Processor which integrates a 2.4GHz, IEEE 802.15.4-compliant transceiver as well as IEEE 802.15.4 PHY and MAC. A24 MHz high stability Xtal is present on board to guarantee the required timing imposed by ZigBee specifications. A single supply voltage is foreseen; an internal voltage regulator supply the different block of the system; the voltage supply fixes also the I/O ports levels allowing an easy interface with the host system. The module is controlled by means of a Standard serial Interface allowing the connections to a variety of Host microcontrollers. APPLICATIONS •Industrial controls •Sensor Networking •Monitoring of remote systems •Home applications •Security systems •Lighting controls FEATURES •Integrated 2.4GHz ,IEEE 802,15,4-compliant transceiver •Integrated IEEE 802.15.4 PHY and MAC •Controlled by a Standard Serial Line for an easy interface of host microcontrollers •Embedded flash and integrated RAM for program and data storage •On board 24 MHz stable Xtal •Integrated RC oscillator ( typ 10KHz) for low power operation •1 uA power consumption in Deep sleep mode •Watchdog timer and power on reset •Pins available for Non-intrusive debug interface (SIF) •Single voltage supply •Available Link and Activity outputs for external Indication / monitor

NOTICE: The results of tests and checks reported in this Test Report refer exclusively to the samples tested and described in the Report itself. This report shall not be reproduced partially or in its entirety without the written approval of IMQ S.p.A. IMQ S.p.A. - Via Quintiliano, 43 – I-20138 MILANO Telecommunications & Telematics for Transports Lab. TEST REPORT Ref. No. ARSH00131 Date: 2007-07-27 Measurements performed in accordance with: FCC Rules : Code of Federal Regulations (CFR) no. 47 PART 15 – RADIO FREQUENCY DEVICES PRODUCT : ZigBee module general purpose TESTED MODEL : SPZB260 FCC ID : S9NZB260A APPLICANT : STMicroelectronics – Centro Direzionale Colleoni – Palazzo Andromeda 3 – I-20044 Agrate Brianza (MI) - ITALY MANUFACTURER : STMicroelectronics – Centro Direzionale Colleoni – Palazzo Andromeda 3 – I-20044 Agrate Brianza (MI) - ITALY TRADEMARK : STMicroelectronics OTHER INFORMATION Testing dates : 2007-07-19 ÷ 2007-07-20 Tested samples No. : 2 Testing Laboratory : IMQ S.p.A. Via Quintiliano, 43 I-20138 MILANO Tested by : R. Radice Signature: Date : 2007-07-27 Checked by: R. Colombo (EMC and R&TTE Lab. Deputy) Signature: Date : 2007-07-27 Revision Sheet Release No. Date Revision Description Rev. 0 2007-07-27 Test Results and Evaluation Report T ELECOMMUNICATIONS & T ELEMATICS FOR T RANSPORTS L ABORATORY TT&T Laboratory Test Report No. ARSH00131 Date 2007-07-27 page 2 of 46 T ELECOMMUNICATIONS & T ELEMATICS FOR T RANSPORTS L ABORATORY CONTENTS 1 General Description of Equipment under Test ........................ 1-3 1.1 APPLICANT............................................................................... 1-3 1.2 MANUFACTURER..................................................................... 1-3 1.3 EQUIPMENT CLASSIFICATION ............................................... 1-3 1.4 BASIC DESCRIPTION OF EQUIPMENT UNDER TEST........... 1-4 1.5 FEATURE OF EQUIPMENT UNDER TEST .............................. 1-5 2 Test Configuration of Equipment under Test .......................... 2-7 2.1 ENVIRONMENTAL CONDITIONS ............................................ 2-7 2.2 DESCRIPTION OF SUPPORT EQUIPMENT............................ 2-7 2.3 INTERFACE IDENTIFICATION AND CONNECTION DIAGRAM OF TEST SYSTEM .......................................................................... 2-8 3 Operation of Equipment under Test ....................................... 3-10 3.1 OPERATING TEST CONDITIONS .......................................... 3-10 4 Tests Identification and Results ............................................. 4-11 4.1 METHODS OF MEASUREMENT............................................ 4-13 4.2 FREQUENCY RANGE INVESTIGATED ................................. 4-13 5 Measurements and Tests Data................................................ 5-14 6 Additional Technical Information ........................................... 6-42 6.1 ELECTROMAGNETICALLY RELEVANT COMPONENTS: ..... 6-42 6.2 RFI SUPPRESSION DEVICES:.............................................. 6-42 6.3 EMI PROTECTION DEVICES:................................................ 6-42 7 Technical Documentation........................................................ 7-43 8 Photographic Documentation ................................................. 8-44 8.1 EUT IDENTIFICATION ............................................................ 8-44 8.2 TEST SET-UP ......................................................................... 8-46 9 Measurement and Test Equipment Instrumentation ............. 9-47 TT&T Laboratory Test Report No. ARSH00131 Date 2007-07-27 page 3 of 46 T ELECOMMUNICATIONS & T ELEMATICS FOR T RANSPORTS L ABORATORY 1 GENERAL DESCRIPTION OF EQUIPMENT UNDER TEST 1.1 APPLICANT NAME STMicroelectronics ADDRESS Centro Direzionale Colleoni – Palazzo Andromeda 3 – I-20044 Agrate Brianza (MI) COUNTRY ITALY 1.2 MANUFACTURER NAME STMicroelectronics ADDRESS Centro Direzionale Colleoni – Palazzo Andromeda 3 – I-20044 Agrate Brianza (MI) COUNTRY ITALY 1.3 EQUIPMENT CLASSIFICATION According to the definition 15.3 (o) EUT is a Intentional Radiator operating within the bands 2400-2483,5 MHz so it shall fulfil provisions of 47CFR Part 15 Subpart C – Intentional radiators – and Section 15.247. TT&T Laboratory Test Report No. ARSH00131 Date 2007-07-27 page 4 of 46 T ELECOMMUNICATIONS & T ELEMATICS FOR T RANSPORTS L ABORATORY 1.4 BASIC DESCRIPTION OF EQUIPMENT UNDER TEST Parameters Value Type of equipment : ƒ ZigBee module general purpose Model : ƒ SPZB260 FCC ID. : ƒ S9NZB260A Trade Name ƒ STMicroelectronics Data cable : ƒ / Telecom cable : ƒ / Power supply type : ƒ DC 3.3V, 41,5mA max. AC power input cable : ƒ / DC power input cable : ƒ / TT&T Laboratory Test Report No. ARSH00131 Date 2007-07-27 page 5 of 46 T ELECOMMUNICATIONS & T ELEMATICS FOR T RANSPORTS L ABORATORY 1.5 FEATURE OF EQUIPMENT UNDER TEST Power specification ƒ 3.3 V dc Operating frequency: ƒ 2405 ÷ 2480 MHz (16 Channels) Maximum RF output power: ƒ < 1 W Modulation: ƒ O-QPSK Channel Spacing: ƒ >1 MHz Antenna: ƒ Dedicated antenna (0,6 dBi gain) integrated in the test jig RX sensitivity: ƒ -92 dBm Main SW identification ƒ / Main HW Board identification ƒ / Peripherals included (for system application) ƒ None Interfaces : ƒ None Integrated interfaces : ƒ None AC adapter: ƒ None TT&T Laboratory Test Report No. ARSH00131 Date 2007-07-27 page 6 of 46 T ELECOMMUNICATIONS & T ELEMATICS FOR T RANSPORTS L ABORATORY CHANNEL CONFIGURATION Channel (No.) Frequency (MHz) 11 2405.00 12 2410.00 13 2415.00 14 2420.00 15 2425.00 16 2430.00 17 2435.00 18 2440.00 19 2445.00 20 2450.00 21 2455.00 22 2460.00 23 2465.00 24 2470.00 25 2475.00 26 2480.00 TT&T Laboratory Test Report No. ARSH00131 Date 2007-07-27 page 7 of 46 T ELECOMMUNICATIONS & T ELEMATICS FOR T RANSPORTS L ABORATORY 2 TEST CONFIGURATION OF EQUIPMENT UNDER TEST 2.1 ENVIRONMENTAL CONDITIONS TEST CONDITIONSMEASURED Ambient Temperature 20 ÷ 25 °C Relative Humidity 50 ÷ 60 % Atmospheric Pressure 900 ÷ 1000 mbar 2.2 DESCRIPTION O…

Text truncated - open the document above for the full version.