SERRC02Action Cam

User Manual Action Cam SP360 4K 1 Before You Start Declaration of Conformity Responsible Party: JK Imaging Ltd. Address: JK Imaging Ltd., 17239 South Main Street, Gardena, CA 90248, USA JK Imaging Europe, 71 Clarendon road, Watford, WD17 1DS, UK Company Website: www.kodakpixpro.com About this Manual Thank you for purchasing this product. Please read this manual carefully and keep it in a safe place for future reference. JK Imaging Ltd. reserves all rights of this document. No part of this published manual may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form, by any means, without the prior written permission of JK Imaging Ltd..                           This manual provides you with instructions on how to use your new KODAK PIXPRO Action Cam. Every effort has been made to ensure that the contents of this manual are accurate; however JK Imaging Ltd. reserves the right to make changes without notice. Throughout this manual, indicates the useful information, " Page number" indicates an introduction to the contents on this page. 2 For Customers in the U.S.A. Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help.                    !     #  This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: This product complies with the FCC portable RF exposure limit set forth for an uncontrolled environment and is safe for intended operation as described in this manual. Additional RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. FOR COUNTRY CODE SELECTION USAGE (WLAN DEVICES) $ %         &'*       '*  +   6<    '*   '* operation channels only. INDUSTRY CANADA This device complies with RSS-247 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Radiation Exposure Statement:       =  $>&?@Q!Z             *     [     suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable. The product comply with the Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. \      !       > ] &'     ^       _^ \   `    # ^     \^    > z  ^  !  z  ^   #     !  #     ^^                    3 For Customers in Europe This symbol [crossed-out wheel bin WEEE Annex IV] indicates separate collection of electrical waste and electronic equipment in the European countries. Please do not throw the equipment into domestic refuse. Please use the return and collection systems available in your country for proper, safe disposal of this product. “CE” mark indicates that this product complies with the European requirements for safety, health, environment and customer protection. “CE” marked cameras are intended for sales in Europe. Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC: - EN60950-1/A12:2011+A2:2013 Safety of Information Technology Equipment - EN 62311:2008         #      …

Text truncated - open the document above for the full version.

Sintai Optical (Shenzhen) Co., Ltd. Qiwei Industrial Park, Li Song Lang Industrial Zone, Gongming Street, Guangming New District, Shenzhen, P.R. China Date: September 3, 2015 We, Sintai Optical (Shenzhen) Co., Ltd. Here declare that the device does not support channel 12 ~ 13 in 2.4GHz band and any non-US channels in all the operational mode(s) for the following product. FCC ID: SERRC02 If you should have any question(s) regarding this declaration, please don’t hesitate to contact us. Thank you! ___________________________________________ Dengchun Li / Manager Sintai Optical (Shenzhen) Co., Ltd. Tel: +86-755-27165959#7524 Fax:+86-755-29168341 E-mail: [email protected]

Sintai Optical (Shenzhen) Co., Ltd. Qiwei Industrial Park, Li Song Lang Industrial Zone, Gongming Street, Guangming New District, Shenzhen, P.R. China Declaration letter Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Declaration letter for label requirement Date: 2015-09-03 FCC ID: SERRC02 The label is permanent affixed in the battery compartment, and the EUT will be selling to market without the battery installed. The users can see the label during the battery installation process. The battery cover can be opened without any special tools. Please don’t hesitate to contact us, if you have any question(s). Thank you! ----------------------------------- Dengchun Li / Manager Sintai Optical (Shenzhen) Co., Ltd. Tel: +86-755-27165959#7524 Fax:+86-755-29168341 E-mail: [email protected]

Sintai Optical (Shenzhen) Co., Ltd. Qiwei Industrial Park, Li Song Lang Industrial Zone, Gongming Street, Guangming New District, Shenzhen, P.R. China Date: 2015-09-03 FCC ID: SERRC02 AUTHORIZATION LETTER To whom it may concern: We, the undersigned, hereby authorize ( name: Amanda Wu and Title: Senior Specialist) of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan) of Taiwan to act on our behalf in all manners relating to FCC application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by (name: Amanda Wu and Title: Senior Specialist) of BV CPS Taoyuan on our behalf shall have the same effect as acts of our own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Sincerely yours, _______________________________________________ Dengchun Li / Manager Sintai Optical (Shenzhen) Co., Ltd. Tel: +86-755-27165959#7524 Fax:+86-755-29168341 E-mail: [email protected]

Sintai Optical (Shenzhen) Co., Ltd. Qiwei Industrial Park, Li Song Lang Industrial Zone, Gongming Street, Guangming New District, Shenzhen, P.R. China Date: 2015-09-03 FCC ID: SERRC02 To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, _____________________________________________ Dengchun Li / Manager Sintai Optical (Shenzhen) Co., Ltd. Tel: +86-755-27165959#7524 Fax:+86-755-29168341 E-mail: [email protected]

TCB GRANT OF EQUIPMENT AUTHORIZATION TCB Certification Issued Under the Authority of the Federal Communications Commission By: UL Japan, Inc. 4383-326 Asama-cho Ise-shi Mie, 5160021 Japan Date of Grant: 11/06/2012 Application Dated: 11/06/2012 Murata Manufacturing Co., Ltd. 10-1, Higashikotari 1-chome Nagaokakyo-shi Kyoto, 617-8555 Japan Attention: MOTOO HAYASHI , GENERAL MANAGER NOT TRANSFERABLE EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below. FCC IDENTIFIER: VPYLBVX532 Name of Grantee: Murata Manufacturing Co., Ltd. Equipment Class:Digital Transmission System Notes:Communication Module Modular Type:Limited Single Modular Grant Notes FCC Rule Parts Frequency Range (MHZ) Output Watts Frequency Tolerance Emission Designator 15C2412.0 - 2462.00.1135 Limited Modular approval. Output power listed is Conducted(Maximum peak). Compliance of this device in all final host configurations is the responsibility of the Grantee. OEM integrators and end-users must be provided with specific operating instructions for satisfying RF exposure compliance. The antenna of this device must not be co-located or used in conjunction with any other antenna or transmitter except the conditions in accordance with FCC multi-transmitter product guidelines.. OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device.This module can only be used with a host antenna circuit trace layout design in strict compliance with the OEM instructions provided. 1 / 1FCC -OET TCB Form 731 Grant of Equipment Authorization 2015/8/6https://apps.fcc.gov/oetcf/tcb/reports/Tcb731GrantForm.cfm?mode=COPY&RequestTi...

Report No. : 150723E03 Page 1 CONSTRUCTION PHOTOS OF EUT Report No. : 150723E03 Page 2 Report No. : 150723E03 Page 16 Report No. : 150723E03 Page 17

(Fig.1) FCC ID: SERRC02 FCC LABEL LOCATION The label will be permanently affixed at a conspicuous location on the device. Back

Report No. : 150723E03 Page 3 Report No. : 150723E03 Page 4 Report No. : 150723E03 Page 5 Report No. : 150723E03 Page 6 Report No. : 150723E03 Page 7 Report No. : 150723E03 Page 8 Report No. : 150723E03 Page 9 Report No. : 150723E03 Page 10 Report No. : 150723E03 Page 11 Report No. : 150723E03 Page 12 Report No. : 150723E03 Page 13 Report No. : 150723E03 Page 14 Report No. : 150723E03 Page 15

FCC SAR Test Report Report Format Version 5.0.0 Page No. : 1 of 26 Report No. : SA150723E03 Issued Date : Sep. 03, 2015 FCC SAR Test Report Report No. : SA150723E03 Applicant : Sintai Optical (Shenzhen) Co., Ltd. Address : Qiwei Industrial Park, Li Song Lang Industrial Zone, Gongming Street, Guangming New District, Shenzhen, P.R. China Product : Action Cam FCC ID : SERRC02 Brand : KODAK Model No. : KODAK PIXPRO SP360 4K Action Cam Standards : FCC 47 CFR Part 2 (2.1093) / IEEE C95.1:1992 / IEEE Std 1528:2013 KDB 865664 D01 v01r04 / KDB 865664 D02 v01r01 KDB 248227 D01 v02r01/ KDB 447498 D01 v05r02 Sample Received Date : Jul. 23, 2015 Date of Testing : Aug. 24, 2015 CERTIFICATION: The above equipment have been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch – Lin Kou Laboratories, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s SAR characteristics under the conditions specified in this report. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval, or endorsement by TAF or any government agencies. Prepared By : Rona Chen / Specialist Approved By : Gordon Lin / Assistant Manager This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. FCC SAR Test Report Report Format Version 5.0.0 Page No. : 2 of 26 Report No. : SA150723E03 Issued Date : Sep. 03, 2015 Table of Contents Release Control Record ............................................................................................................................................................... 3 1. Summary of Maximum SAR Value ....................................................................................................................................... 4 2. Description of Equipment Under Test ................................................................................................................................. 5 3. SAR Measurement System ................................................................................................................................................... 6 3.1 Definition of Specific Absorption Rate (SAR) ............................................................................................................... 6 3.2 SPEAG DASY System ................................................................................................................................................. 6 3.2.1 Robot.................................................................................................................................................................. 7 3.2.2 Probes ................................................................................................................................................................ 8 3.2.3 Data Acquisition Electronics (DAE) .................................................................................................................... 8 3.2.4 Phantoms ........................................................................................................................................................... 9 3.2.5 Device Holder ................................................................................................................................................... 10 3.2.6 System Validation Dipoles ................................................................................................................................ 10 3.2.7 Tissue Simulating Liquids ................................................................................................................................. 11 3.3 SAR System Verification ............................................................................................................................................ 14 3.4 SAR Measurement Procedure ................................................................................................................................... 15 3.4.1 Area & Zoom Scan Procedure ......................................................................................................................... 15 3.4.2 Volume Scan Procedure................................................................................................................................... 15 3.4.3 Power Drift Monitoring ...................................................................................................................................... 16 3.4.4 Spatial Peak SAR Evaluation ........................................................................................................…

Text truncated - open the document above for the full version.

Test report No. : 33AE0059-HO-01-A-R1 Page : 2 of 110 Issued date : October 19, 2012 Revised date : October 24, 2012 FCC ID : VPYLBVX532 UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124 CONTENTS PAGE SECTION 1: Customer information ......................................................................................................... 3 SECTION 2: Equipment under test (E.U.T.) ........................................................................................... 3 SECTION 3: Test specification, procedures & results ............................................................................ 4 SECTION 4: Operation of E.U.T. during testing .................................................................................... 8 SECTION 5: Conducted Emission .......................................................................................................... 10 SECTION 6: Radiated Spurious Emission ............................................................................................ 11 SECTION 7: Antenna Terminal Conducted Tests ................................................................................ 13 APPENDIX 1: Data of EMI test .............................................................................................................. 14 6dB Bandwidth ................................................................................................................................. 22 Maximum Peak Output Power ......................................................................................................... 28 Average Output Power ..................................................................................................................... 34 Radiated Spurious Emission ............................................................................................................. 36 Conducted Spurious Emission .......................................................................................................... 57 Conducted Emission Band Edge compliance ................................................................................... 75 99%Occupied Bandwidth ............................................................................................................... 101 APPENDIX 2: Test instruments ........................................................................................................... 105 APPENDIX 3: Photographs of test setup ............................................................................................. 107 Conducted Emission ....................................................................................................................... 107 Radiated Spurious Emission ........................................................................................................... 108 Worst Case Position ....................................................................................................................... 109 Test report No. : 33AE0059-HO-01-A-R1 Page : 3 of 110 Issued date : October 19, 2012 Revised date : October 24, 2012 FCC ID : VPYLBVX532 UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124 SECTION 1: Customer information Company Name : Murata Manufacturing Co., Ltd. Address : 10-1, Higashikotari 1-chome, Nagaokakyo-shi, Kyoto 617-8555 Japan Telephone Number : +81-75-955-6735 Facsimile Number : +81-75-955-6634 Contact Person : TAKAHARU KAWAKATSU SECTION 2: Equipment under test (E.U.T.) 2.1 Identification of E.U.T. Type of Equipment : Communication Module Model No. : Type VX Serial No. : Refer to Section 4, Clause 4.2 Rating : DC 2.85V / DC 3.4V Receipt Date of Sample : September 29, 2012 Country of Mass-production : China Condition of EUT : Engineering prototype (Not for Sale: This sample is equivalent to mass-produced items.) Modification of EUT : No Modification by the test lab 2.2 Product Description General Specification The EUT is Communication Module which is installed in Digital camera and Movie Camera. It has two output power settings: Low power for Digital Camera and High power for Movie Camera. Tests in this report have been performed with both setting of output power. Specification of WLAN (IEEE802.11b/g/n) Type of radio Wireless LAN (IEEE802.11b/g) Wireless LAN (IEEE802.11n) 2.4G Band SISO (20M Band) Equipment Type Transceiver Frequency of Operation 2412MHz - 2462MHz Bandwidth & Channel spacing Bandwidth : 20MHz Ch spacing : 5MHz Type of Modulation 11b: DSSS 11g: OFDM OFDM Antenna Type High Power: Pattern Antenna Low Power: FPC Antenna Antenna Gain High Power: -3.7dBi Low Power: -4.5 dBi Power Supply (inner) DC 2.85V / DC 3.4V Operating temperature range -20 to +55 deg. C. Test report No. : 33AE0059-HO-01-A-R1 Page : 4 of 110 Issued date : October 19, 2012 Revised date : October 24, 2012 FCC ID : VPYLBVX532 UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8116 Facsimile : +81 596 24 8124 SECTION 3: Test specification, procedures & results 3.1 Test Specification Test Specification : FCC Part 15 Subpart C: 2012, final revised on August 13, 2012 and effective September 12, 2012 Title : FCC 47CFR Part15 Radio Frequency Device Subpart C Intentional Radiators Section 15.207 Conducted limits Section 15.247 Operation within the bands 902-928MHz, 2400-2483.5MHz, and 5725-5850MHz 3.2 Procedures and results Item Test Procedure Specification Worst margin Results Remarks Conducted Emission FCC: ANSI C63.4:2003 7. AC powerline Conducted Emission measurements FCC: Section 15.207 [Low Power] QP 19.1dB, 0.15000MHz, L AV 27.8dB, 24.93727MHz, L [High Power] QP 18.2dB, 0.15166MHz, L AV 24.5dB, 24.93734MHz, N Complied- IC: RSS-Gen 7.2.4 IC: RSS-Gen 7.2.4 6dB Bandwidth FCC: "Guidance on Measurement of Digital Transmission Systems Operating under Section15.24…

Text truncated - open the document above for the full version.

Report No.: RF150723E03 Page No. 1 / 26 Report Format Version: 6.1.1 FCC Test Report Report No.: RF150723E03 FCC ID: SERRC02 Test Model: KODAK PIXPRO SP360 4K Action Cam Received Date: July 23, 2015 Test Date: Aug. 24 to 27, 2015 Issued Date: Sep. 16, 2015 Applicant: Sintai Optical (Shenzhen) Co., Ltd. Address: Qiwei Industrial Park, Li Song Lang Industrial Zone, Gongming Street, Guangming New District, Shenzhen, P.R. China Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory Lab Address: No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan R.O.C. Test Location (1): No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan R.O.C. Test Location (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan R.O.C. Test Location (3): E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Taiwan R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF150723E03 Page No. 2 / 26 Report Format Version: 6.1.1 Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ...................................................................................................................... 4 2 Summary of Test Results ..................................................................................................................... 5 2.1 Measurement Uncertainty ................................................................................................................... 5 2.2 Modification Record ............................................................................................................................ 5 3 General Information .............................................................................................................................. 6 3.1 General Description of EUT ................................................................................................................ 6 3.2 Description of Test Modes ................................................................................................................... 8 3.2.1 Test Mode Applicability and Tested Channel Detail ............................................................................. 9 3.3 Duty Cycle of Test Signal .................................................................................................................. 10 3.4 Description of Support Units .............................................................................................................. 11 3.4.1 Configuration of System under Test ................................................................................................... 11 3.5 General Description of Applied Standards ........................................................................................ 12 4 Test Types and Results ...................................................................................................................... 13 4.1 Radiated Emission and Bandedge Measurement ............................................................................. 13 4.1.1 Limits of Radiated Emission and Bandedge Measurement .............................................................. 13 4.1.2 Test Instruments ................................................................................................................................ 14 4.1.3 Test Procedures ................................................................................................................................. 15 4.1.4 Deviation from Test Standard ............................................................................................................ 15 4.1.5 Test Set Up ........................................................................................................................................ 16 4.1.6 EUT Operating Conditions ................................................................................................................. 16 4.1.7 Test Results ....................................................................................................................................... 17 4.2 Conducted Emission Measurement .................................................................................................. 21 4.2.1 Limits of Conducted…

Text truncated - open the document above for the full version.