SIP-7587-TArm Blood Pressure Monitor

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user isencouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. FCC RF Radiation Exposure Statement: 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with RF radiation exposure limits set forth for an uncontrolled environ- ment. 3.The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. The operating temperature of the EUT can’t exceed 35 ºC and shouldn’t be lower than 0ºC. Hereby, MegaGain International Ltd.declares that this product is in compliance with essential requirements and other relevant provisions of Directive 2014/53/EU. This product is allowed to be used in all EU member states. Frequency bands Maximum output power 2420-2462MHz -2.36dBm(EIRP)

SN4071217

External Photos

V ersion:00 The Label Location: label shall be permanently affixed to the equipment 1 4mm 56mm F CC ID:SIP -758 7 -T THI S DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1 ) TH IS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2 ) TH IS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDI NG INTE RFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

Internal Photos

FCC ID: SIP-7587-T RF Exposure Evaluation REQUIREMENT KDB447498 D01 General RF Exposure Guidance v06, Clause 4.3.1(a) [(max. power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 Where -f(GHz) is the RF channel transmit frequency in GHz -Power and distance are rounded to the nearest mW and mm before calculation -The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm, and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm according to 4.1 f) is applied to determine SAR test exclusion. TEST RESULT Passed Not Applicable Modulation Frequency range (MHz) Conducted Power (dBm) Maximum Tune-up (dBm) Calculating data Limit Result GFSK 2420-2462 -2.47 -2.00 0.196 3.00 Pass Note: 1) The maximum antenna gain is 0dBi 2) The exposure evaluation safety distance is 5mm.

Page: 1 of 32 TEST REPORT For GFSK Report No. ...................................... : CHTW24070001 Report Verification: Project No.................................： SHT2406017001W FCC ID ............................................. : SIP-7587-T Applicant’s name ........................... : MegaGain International Ltd. Address ............................................. : Rm 904-905, Greenfield Tower, Concordia Plaza,1 Science Museum Road, T.S.T. East. Kowloon. HongKong Product Name ................................ : TAF ALIEN Trade Mark ....................................... : - Model No. ......................................... : 2401-DW13054(7587-T) Listed Model(s) ................................. : - Standard ......................................... : FCC CFR Title 47 Part 15 Subpart C § 15.247 Date of receipt of test sample..........: Jun.19, 2024 Date of testing.............................: Jun.19, 2024 - Jun.28, 2024 Date of issue...............................: Jul.01, 2024 Result .................. ........................: PASS Compiled by ( Position+Printed name+Signature): File administrators Kiki Kong Supervised by (Position+Printed name+Signature): Project Engineer Kiki Kong Approved by (Position+Printed name+Signature): RF Manager Xu yang Testing Laboratory Name ............. : Shenzhen Huatongwei International Inspection Co., Ltd. Address ............................................. : Building 7, Baiwang Idea Factory, No.1051, Songbai Road, Yangguang Community, Xili Subdistrict, Nanshan District, Shenzhen, Guangdong, China Shenzhen Huatongwei International Inspection Co., Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen Huatongwei International Inspection Co., Ltd. is acknowledged as copyright owner and source of the material. Shenzhen Huatongwei International Inspection Co., Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. The test report merely correspond to the test sample. Report No.: CHTW24070001 Page: 2 of 32 Date of issue: 2024-07-01 Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V06(2023-09) Contents 1. TEST S T A N D A R D S AND R E P O R T V E R S I O N 3 1.1. Test Standards 3 1.2. Report version 3 2. TEST DESCRIPTION 4 3. SUMMARY 5 3.1. Client Information 5 3.2. Product Description 5 3.3. Radio Specification Description 5 3.4. Testing Laboratory Information 6 4. TEST CONFIGURATION 7 4.1. Test frequency list 7 4.2. Descriptions of Test mode 7 4.3. Test sample information 7 4.4. Support unit used in test configuration and system 8 4.5. Testing environmental condition 8 4.6. Statement of the measurement uncertainty 8 4.7. Equipment Used during the Test 9 5. TEST CONDITIONS AND RESULTS 11 5.1. Antenna Requirement 11 5.2. AC Conducted Emission 12 5.3. Peak Output Power 13 5.4. Power Spectral Density 14 5.5. 6dB bandwidth 15 5.6. 99% Occupied Bandwidth 16 5.7. Duty Cycle 17 5.8. Conducted Band edge and Spurious Emission 18 5.9. Radiated Band edge Emission 19 5.10. Radiated Spurious Emission 21 6. TEST SETUP PHOTOS 26 7. EXTERNAL AND INTERNAL PHOTOS 28 7.1. External Photos 28 7.2. Internal Photos 30 8. APPENDIX REPORT 32 Report No.: CHTW24070001 Page: 3 of 32 Date of issue: 2024-07-01 Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V06(2023-09) 1. TEST STANDARDS AND REPORT VERSION 1.1. Test Standards The tests were performed according to following standards: ‒ FCC CFR Title 47 Part 15 Subpart C § 15.247: Operation within the bands 902-928 MHz, 2400-2483.5 MHz, and 5725-5850 MHz ‒ ANSI C63.10:2020: American National Standard for Testing Unlicensed Wireless Devices ‒ KDB 558074 D01 15.247 Meas Guidance v05r02: Guidance for Compliance Measurements on Digital Transmission System, Frequency Hopping Spread Spectrum System, and Hybrid System Devices Operating under Section 15.247 of The FCC Rules 1.2. Report version Revision No. Date of issue Description N/A 2024-07-01 Original Report No.: CHTW24070001 Page: 4 of 32 Date of issue: 2024-07-01 Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V06(2023-09) 2. TEST DESCRIPTION Report clause Test Items Standard Requirement Result Test Engineer 5.1 Antenna Requirement 15.203/15.247(c) PASS Chenxin Ling 5.2 AC Conducted Emission 15.207 N/A N/A 5.3 Peak Output Power 15.247(b)(3) PASS Chenxin Ling 5.4 Power Spectral Density 15.247(e) PASS Chenxin Ling 5.5 6dB Bandwidth 15.247(a)(2) PASS Chenxin Ling 5.6 99% Occupied Bandwidth - PASS *1 Chenxin Ling 5.7 Duty cycle - PASS *1 Chenxin Ling 5.8 Conducted Band Edge and Spurious Emission 15.247(d)/15.205 PASS Chenxin Ling 5.9 Radiated Band Edge Emission 15.205/15.209 PASS Yifan Wang 5.10 Radiated Spurious Emission 15.247(d)/15.205/15.209 PASS Yifan Wang Note: ‒ The measurement uncertainty is not included in the test result. ‒ *1: No requirement on standard, only report these test data. ‒ N/A: Not tested Report No.: CHTW24070001 Page: 5 of 32 Date of issue: 2024-07-01 Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V06(2023-09) 3. SUMMARY 3.1. Client Information Applicant: MegaGain International Ltd. Address: Rm 904-905, Greenfield Tower, Concordia Plaza,1 Science Museum Road, T.S.T. East. Kowloon. HongKong Manufacturer: MegaGain International Ltd. Address: Rm 904-905, Greenfield Tower, Concordia Plaza,1 Science Museum Road, T.S.T. East. Kowloon. HongKong Factory: JEM Master Tech (Jiangxi) Manufacturing Co., Ltd. Address: Leiden industrial Zone, Industrial Park, Xinfeng Country Ganzhou, Jiangxi, China 3.2. Product Description Main unit information: Product Name: TAF ALIEN Trade Mark: - Model No.: 2401-DW13054(7587-T) Listed Model(s): - Power supply: DC 4.5V from Battery Hardware version: V1 Software version: V1 3.3. Radio Specification Description …

Text truncated - open the document above for the full version.

Antenna Specification

TEST SETUP PHOTOS Radiated Emission