SJ6KBWJ20070905Wireless Keyboard

User manual 一、1、This K/B and mouse use a frequency of 2.4GHZ ,can work with 360 degrees.and with many internet hot keys ,can be used more than 10 meters which can be used more convience and satisfactory. 2、Wireless K/B use battery as the power,many power save ways have beed used .The K/B can be change to sleep mode when don’t use any keys within 5 miniutes.then the MCU will stop to work ,the receive light will glint to show that the connection is cut off.at such time when press any key the K/B can wake up and work again automatic. 二、Combine parts：K/B, Wireless Mouse, receiver, two alkalescence batteries,two rechargeable batteries,a connection cable,a driver and user manual. 三、User guide： 1、 Release your formal K/B, mouse and the driver for your formal K/B also included. 2、 Put batteries to the K/B and mouse. 3、 Put the connector to your PC USB port, and then the match code light will glint slowly. 4、 Receiver ,Keyboard and mouse to match the ID code. 4.1 Press the receiver’s match code switch, the instruction light will glint quickly,then press the K/B or Mouse’s match code ,If the instruction light can chang from quick glint to slow glint,that means three of them matches. (all the match should be finished within 15 seconds) If more than 15 seconds ,Please rework as above. 4.2 The other’s ID code match is the same as 4.1 4.3 When both the K/B and mouse are match well ,then the instruction light of Receiver will illuminated all the time ,that means the K/B and mouse can work . 5、 Low power instruction: 5.1 K/B use two batteries as the power,if the voltage lower than designed voltage ,then the low power instruction light will glint .at this time ,please change the batteries. 5.2 When the mouse’s power voltage lower than work voltage ,the mouse may can not work normally,and the low instruction light will glint,at this time please charge the batteries about 6 hours 四、Function 1、Mouse： 1、Left key；2、Middletrolley；3、back；4、forward；5. right key 2、Keyboard RFwireless 1 2 3 4 5 6 7 8 9 1、 Back: Back, back to the formal item you have already scan .such as web browser 2、 Web site: Goes to web home page 3、 Email: Calls the email application 4、 Forward: Changes to the previous media track 5、 Pre-track : Change to the formal media 6、 Stop: Stop the media play,when press “ Play/Pause” then the media will play again. 7、 Play/Stop: Change media play and stop.If it is stop, press this key again then it will play again. 8、 Next-track : Change to next media ,each press ,it will be go next media 9、Sleep:If the system support the power management and the power management is used,then the system will enter into Power management mode.If the system doesn’t support the power management ,the Hot keys can not be used. 五、Install the Driver： 1、 Driver for the hot keys is needed on operating system of lower than Windows 2000. 2、 Before install the driver ,please release all the other K/B and Mouse’s driver. 3、 Insert the CD-ROM to the computer. And run Keyboard setup.exe. FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

ShenZhen WeiJian Plastics Co., Ltd. Add: ShangPai Industrial Park,ShiYan Township, BaoAn District,ShenZhen,China Tel:+86-755-27658366 Fax:+86-755-29816282 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Gentlemen: This letter is to comply with Sections 0.457 and 0.459 pertaining to confidential material. ShenZhen WeiJian Plastics Co., Ltd. would like the following documents regarding this submission for FCC ID: SJ6- KBWJ20070905 to be kept confidential. 1. Schematics 2. Operational description 3. Block diagram The above material contains trade secrets or technical data, which would customarily be guarded from competitors. We do not want these documents to be accessible to the general public. Sincerely, ShenZhen WeiJian Plastics Co., Ltd.

FCC ID: SJ6KBWJ20070905 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Proposed Label Location on EUT FCC ID Label Location

ISO/IEC17025 Accredited Lab. Report No: FCC0709025 File reference No: 2007-11-09 Applicant: SHENZHEN WEIJIAN PLASTICS CO., LTD Product: Wireless Keyboard Model No: W9864RF Brand Name: N/A Test Standards: FCC Part 15 Subpart C, Paragraph 15.249 Test result: It is herewith confirmed and found to comply with the requirements set up by ANSI C63.4&FCC Part 15 Subpart C, Paragraph 15.249 regulations for the evaluation of electromagnetic compatibility Approved By Jack Chung Manager Dated: Nov 09, 2007 Results appearing herein relate only to the sample tested The technical reports is issued errors and omissions exempt and is subject to withdrawal at SHENZHEN TIMEWAY TECHNOLOGY CONSULTING CO LTD East 5/Block 4, Anhua Industrial Zone, No.8,Tairan Rd. CheGongMiao, FuTian District, Shenzhen, CHINA. Tel (755) 83448688 Fax (755) 83442996 Report No: 0709025 Page 2 of 45 Date: 2007-11-09 TEST REPORT The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the Shenzhen Timeway Technology Consulting Co .,Ltd. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the Shenzhen Timeway Technology Consulting co .,Ltd to his customer. Supplier or others persons directly concerned. Shenzhen Timeway Technology Consulting co .,Ltd will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The Shenzhen Timeway Technology Consulting co .,Ltd reserves the rights to withdraw it and to adopt any other remedies which may be appropriate. Special Statement： The testing quality ability of our laboratory meet with "Quality Law of People's Republic of China" Clause 19. The testing quality system of our laboratory meets with ISO/IEC-17025 requirements, which is approved by CNAS. This approval result is accepted by MRA of APLAC. Our test facility is recognized, certified, or accredited by the following organizations: CNAS-LAB Code: L2292 The EMC Laboratory has been assessed and in compliance with CNAS-CL01 accreditation criteria for testing Laboratories (identical to ISO/IEC 17025:1999 General Requirements) for the Competence of testing Laboratories. FCC-Registration No.: 899988 The EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications commission. The acceptance letter from the FCC is maintained in our files. Registration No.:899988. IC- Registration No.: IC5205A-01 The EMC Laboratory has been registered and fully described in a report filed with the (IC) Industry Canada. The acceptance letter from the IC is maintained in our files. Registration No.: IC 5205A-01. Report No: 0709025 Page 3 of 45 Date: 2007-11-09 TEST REPORT The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the Shenzhen Timeway Technology Consulting Co .,Ltd. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the Shenzhen Timeway Technology Consulting co .,Ltd to his customer. Supplier or others persons directly concerned. Shenzhen Timeway Technology Consulting co .,Ltd will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The Shenzhen Timeway Technology Consulting co .,Ltd reserves the rights to withdraw it and to adopt any other remedies which may be appropriate. Test Report Conclusion Content 1.0 General Details ................................................................................................ 4 1.1 Test Lab Details................................................................................................ 4 1.2 Applicant Details.............................................................................................. 4 1.3 Description of EUT .......................................................................................... 4 1.4 Submitted Sample............................................................................................. 4 1.5 Test Duration.................................................................................................... 4 1.6 Test Uncertainty.................................................................................................5 1.7 Test By.......................................................................................................... 5 2.0 List of Measurement Equipment......................................................................... 5 3.0 Technical Details............................................................................................. 7 3.1 Summary of Test Results..................................................................................... 7 3.2 Test Standards.................................................................................................. 7 4.0 EUT Modification............................................................................................. 7 5.0 Power Line Conducted Emission Test...................................................................... 8 5.1 Schematics of the Test........................................................................................ 8 5.2 Test Method and Test Procedure............................................................................ 8 5.3 Configuration of the EUT.................................................................................... 8 5.4 EUT Operating Condition..................................…

Text truncated - open the document above for the full version.