SK2-2400RS2.4G Wireless Data Transceiver

2.4GHz WIRELESS DATA TRANSCEIVER USER MANUAL MODEL:15-2400RSK Panel View ○ 1 ○ 2 ○ 3 ○ 4 ○ 5 ○ 6 ○ 7 ○ 8 ○ 9 ○ 10 1. DC+12V IN: DC 12V Power Input 2. BAUD RATE and TERMINATION: Baud rate and 120 Ohm termination setting by DIP switch. (Note: After changing the baud rate by DIP switch, please re-boot the device again.) 3. RS485 PORT: 2-wire Half-Duplex RS485 support. 4. ALARM IN: TTL/CMOS digital Input which could be connected to alarm sensor or digital control signal, e.g.: Magnetic Reed Switch Detector. 5. ALARM OUT: Reed Relay Output (NC/COM/NO) that could be connected to alarm devices, e.g.: Siren, Flashing Unit. 6. POWER ON or RF LINK LED: Indicated to power on or RF link status. Indications Power/RF LINK LED Power On On RF Link Loss Low Flashing 7. RS 485 or PAIRING LED: Indicated to RS485 data are transmitted or received and waiting pairing status. Indications Power/RF LINK LED RS485 High Flashing Waiting Pairing Low Flashing 8. PAIRING KEY: To set the device into pairing mode. Please do the pairing procedure before connecting the devices to RS485 network. (Pleas refer to the pairing procedure for more detail.) 9. MASTER or SLAVE: For RF pairing only. 10. ANT: SMA connector for connected to 2.4 GHz antennas. REMARK: Don’t close 802.11 a/b/g AP router and other 2.4GHz devices. Pairing procedure: (1) Make sure these two devices, one is set to “Master” and another is “Slave”. (2) Please hold the “Pairing KEY” of the master device until the device connected to DC12V power supply and then you can find the “Pairing LED” of master device is flashing. (3) Please do the same procedure as step (2) again for the slave device. (4) When the pairing procedure is complete, the “RF Link LED” of two devices is on. 2. Caution for Installation 2.1 Be careful, never let any water in this equipment. 2.2 If necessary, use a soft cloth moistened with alcohol to wipe off the dust. 2.3 Be extra careful not to shake the unit. 2.4 Avoid places where temperatures exceed 55 o C or higher. 2.5 Avoid places where there are frequent vibrations or shocks. 2.6 When any abnormalities occur, make sure to unplug the unit and contact your local dealer. 3. Packing 3.1 Transceiver ×2 3.2 Antenna ×2 3.3 User manual ×1 3.4 Screws ×8 3.5 Plastic-Conical-Anchor ×8 3.6 Power Adaptor ×2 [Option] 4. Specification Items 15-2400RSK Frequency Channels 2402 ~ 2480 MHz,79-CH (CE/FCC) RF TX Power 100 mW (Average) Min. RX Sensitivity -86dBm RF Impedance 50Ω RS485 2-wire RS485 Half Duplex Data Baud Rate :2400/4800/9600 bps Fixed Format:1 Start bit, 1 Stop bit, 8 Data Bits, No Parity Dual Directional ALARM I/O -ALARM Input: TTL/CMOS -ALARM Output:NC/COM/NO (Dry Contact) Contact Rating: AC 125V / 0.5A ; DC 24V / 1A Power Consumption 60 mA Max. @ DC12V Weight (without antenna) < 124.8g (4.4 oz) Operation Temperature -10°C ~ 55°C Storage Temperature -30°C ~ 85°C Dimensions (W × L × H) (excluding connectors and without antenna) 92 × 75 × 25mm (3.62” × 2.95” × 1.00”) FCC Part 15 Notice: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. 3. Any changes or modifications (including the antennas) made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment. Q2011/04/19

COP Security System Corp. 4-6F, NO.5, Lane 130, Min-Chung Rd, Hsin Tien City, Taipei Hsien., Taiwan R.O.C. (23141) Attestation for FCC Declaration of Conformity FCC ID: SK2-2400RS Data: Apr. 26, 2011 Please be notified that we, the undersigned, COP Security System Corp. declares that the product which bears the above FCC ID is also compliant with the FCC requirements for DoC. The test report number supporting the DoC is 113401R-RFUSP37V02 Testing in regards to this report was done by QuieTek Corporation, located at 2F, No.345, Xinhu 2nd Rd., Neihu District,, Taipei Taiwan, which has been accredited in accordance to all of the requirements of 47CFR 2.948 (d) and (e) of the FCC rules and KDB349827. Sincerely, Ian Yang / Senior Engineer COP Security System Corp. Tel: 886-2- 22180302 Fax:886-2- 22181628 E-mail: [email protected]

COP Security System Corp. 4-6F, NO.5, Lane 130, Min-Chung Rd, Hsin Tien City, Taipei Hsien., Taiwan R.O.C. (23141) Federal Communications Commission Apr. 26, 2011 Authorization and Evaluation Division ATTESTATION FCC ID: SK2-2400RS Product:: 2.4G Wireless Data Transceiver Model: 15-2400RSK, 15-2400RS We don't provide any controls or software to allow operation outside the USA frequency band when we sell this product in USA. We also promise that the end user or installer will not be able to change countries. For United States only channels 1-79 will be available. Best Regards Ian Yang / Senior Engineer COP Security System Corp. Tel: 886-2- 22180302 Fax:886-2- 22181628 E-mail: [email protected]

COP Security System Corp. 4-6F, NO.5, Lane 130, Min-Chung Rd, Hsin Tien City, Taipei Hsien., Taiwan R.O.C. (23141) Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: SK2-2400RS Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Exhibit Type Block Diagram Schematics Operational Description BOM List The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Ian Yang / Senior Engineer COP Security System Corp. Tel: 886-2- 22180302 Fax:886-2- 22181628 E-mail: [email protected]

COP Security System Corp. 4-6F, NO.5, Lane 130, Min-Chung Rd, Hsin Tien City, Taipei Hsien., Taiwan R.O.C. (23141) Declaration of Authorization We Name: COP Security System Corp. Address: 4-6F, NO.5, Lane 130, Min-Chung Rd, Hsin Tien City, City: Taipei Hsien. Country: Taiwan R.O.C. (23141) Declare that: Name Representative of agent: Gene Chang Agent Company name: QuieTek Corporation Address: 2F, No. 345, Xinhu 2nd Rd., Neihu District, City: Taipei City 114, Country: Taiwan, R.O.C. is authorized to apply for Certification of the following product(s): Product description: 2.4G Wireless Data Transceiver Type designation: 15-2400RSK, 15-2400RS Trademark: FCC ID: SK2-2400RS on our behalf. Date: 2011/04/26 Signature: Ian Yang / Senior Engineer COP Security System Corp. Tel: 886-2- 22180302 Fax:886-2- 22181628 E-mail: [email protected]

Report No：113401R-RFUSP37V02 Page: 73 of 79 Attachement EUT Photograph (1) EUT Photo (2) EUT Photo Report No：113401R-RFUSP37V02 Page: 74 of 79 (3) EUT Photo

FCC ID.: SK2-2400RS FCC ID AND DoC Label The FCC ID and DoC Label will be placed on the equipment as shown in the photograph below. 2.4G Wireless Data Linker Model No.: 15-2400RSK, 15-2400RS F F C C C C I I D D : : S S K K 2 2 - - 2 2 4 4 0 0 0 0 R R S S This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. S/N: Made in Taiwan Trade name: Model number.: 15-2400RSK, 15-2400RS

FCC ID.: SK2-2400RS FCC ID AND DoC Label The FCC ID and DoC Label will be placed on the equipment as shown in the photograph below. 2.4G Wireless Data Linker Model No.: 15-2400RSK, 15-2400RS F F C C C C I I D D : : S S K K 2 2 - - 2 2 4 4 0 0 0 0 R R S S This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. S/N: Made in Taiwan Trade name: Model number.: 15-2400RSK, 15-2400RS

Report No：113401R-RFUSP37V02 Page: 75 of 80 (4) EUT Photo (5) EUT Photo Report No：113401R-RFUSP37V02 Page: 76 of 80 (6) EUT Photo (7) EUT Photo Report No：113401R-RFUSP37V02 Page: 77 of 80 (8) EUT Photo (9) EUT Photo Report No：113401R-RFUSP37V02 Page: 78 of 80 (10) EUT Photo (11) EUT Photo Report No：113401R-RFUSP37V02 Page: 79 of 80 (12) EUT Photo Report No：113401R-RFUSP37V02 Page: 80 of 80 (13) EUT Photo

Report No. 113401R-RF-US-Exp Page: 1 of 3 RF Exposure Evaluation declaration Product Name ： 2.4G Wireless Data Transceiver Model No. ： 15-2400RSK, 15-2400RS FCC ID. ： SK2-2400RS Applicant : COP Security System Corp. Address : 4-6F, NO.5, Lane 130, Min-Chung Rd, Hsin Tien City, Taipei Hsien., Taiwan R.O.C. (23141) Date of Receipt : 2011/03/25 Date of Declaration : 2011/04/27 Report No. : 113401R-RF-US-Exp Report Version : V1.0 The declaration results relate only to the samples calculated. The declaration shall not be reproduced except in full without the written approval of QuieTek Corporation. Report No. 113401R-RF-US-Exp Page: 2 of 3 1. RF Exposure Evaluation 1.1. Limits According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in 1.1307(b) LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (Minutes) (A) Limits for Occupational/ Control Exposures 300-1500 -- -- F/300 6 1500-100,000 -- -- 5 6 (B) Limits for General Population/ Uncontrolled Exposures 300-1500 -- -- F/1500 6 1500-100,000 -- -- 1 30 F= Frequency in MHz Friis Formula Friis transmission formula: Pd = (Pout*G)/(4*pi*r 2 ) Where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm Pd id the limit of MPE, 1 mW/cm 2 . If we know the maximum gain of the antenna and the total power input to the antenna, through the calculation, we will know the distance r where the MPE limit is reached. 1.2. Test Procedure Software provided by client enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. The temperature and related humidity: 18°Cand 78％ RH. Report No. 113401R-RF-US-Exp Page: 3 of 3 1.3. Test Result of RF Exposure Evaluation Product 2.4G Wireless Data Transceiver Test Mode Mode 1: Transmit Test Condition RF Exposure Evaluation Antenna Gain Antenna Gain: The maximum Gain measured in fully anechoic chamber is 5dBi or 3.162 in linear scale. Output Power into Antenna & RF Exposure Evaluation Distance: Channel Channel Frequency (MHz) Output Power to Antenna (mW) Power Density at R = 20 cm (mW/cm 2 ) 1 2402 65.1328 0.04097 40 2441 68.5962 0.04315 79 2480 58.4655 0.03678

Report No：113401R-RFUSP37V02 Page: 1 of 80 Test Report Product Name ： 2.4G Wireless Data Transceiver Model No. ： 15-2400RSK, 15-2400RS FCC ID. ： SK2-2400RS Applicant ： COP Security System Corp. Address ： 4-6F, NO.5, Lane 130, Min-Chung Rd, Hsin Tien City, Taipei Hsien., Taiwan R.O.C. (23141) Date of Receipt：2011/03/25 Issued Date ：2011/04/27 Report No. ：113401R-RFUSP37V02 Report Version ：V1.0 0The test results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. Report No：113401R-RFUSP37V02 Page: 2 of 80 Test Report Certification Issued Date : 2011/04/27 Report No. : 113401R-RFUSP37V02 Product Name ： 2.4G Wireless Data Transceiver Applicant ： COP Security System Corp. Address ： 4-6F, NO.5, Lane 130, Min-Chung Rd, Hsin Tien City, Taipei Hsien., Taiwan R.O.C. (23141) Manufacturer ： COP Security System Corp. Model No. ： 15-2400RSK, 15-2400RS FCC ID. ： SK2-2400RS EUT Voltage : AC 100~240V, 50/60Hz Trade Name ： Applicable Standard ： FCC CFR Title 47 Part 15 Subpart C Section 15.247: 2010 Test Result ： Complied The test results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. Documented By : ( Carol Tsai / Engineering Adm. Specialist ) Reviewed By : ( JuBo Shen / Engineer ) Approved By : ( Roy Wang / Manager ) Report No：113401R-RFUSP37V02 Page: 3 of 80 TABLE OF CONTENTS Description Page 1. General Information ..................................................................................................... 5 1.1. EUT Description ............................................................................................................. 5 1.2. Operational Description .................................................................................................. 7 1.3. Test Mode .......................................................................................................................8 1.4. Tested System Details .................................................................................................... 9 1.5. Configuration of tested System ...................................................................................... 9 1.6. EUT Exercise Software ................................................................................................ 10 1.7. Test Facility...................................................................................................................11 2. Conducted Emission.................................................................................................. 13 2.1. Test Equipment............................................................................................................. 13 2.2. Test Setup .................................................................................................................... 13 2.3. Limits ............................................................................................................................ 14 2.4. Test Procedure ............................................................................................................. 14 2.5. Test Specification.......................................................................................................... 14 2.6. Uncertainty ................................................................................................................... 14 2.7. Test Result....................................................................................................................15 2.8. Test Photo .................................................................................................................... 17 3. Peak Power Output .................................................................................................... 18 3.1. Test Equipment............................................................................................................. 18 3.2. Test Setup .................................................................................................................... 18 3.3. Test procedures ............................................................................................................ 18 3.4. Limits ............................................................................................................................ 18 3.5. Uncertainty ................................................................................................................... 18 3.6. Test Result....................................................................................................................19 4. Radiated Emission ..................................................................................................... 26 4.1. Test Equipment............................................................................................................. 26 4.2. Test Setup .................................................................................................................... 26 4.3. Limits ............................................................................................................................ 27 4.4. Test Procedure ............................................................................................................. 27 4.5. Uncertainty ................................................................................................................... 27 4.6. Test Result....................................................................................................................28 4.7. Test Photo .................................................................................................................... 36 5. RF antenna conducted test ....................................................................................... 38 5.1. Test Equipment............................................................................................................. 38 5.2…

Text truncated - open the document above for the full version.

Report No：113401R-RFUSP37V02 Page: 17 of 79 2.8. Test Photo Test Mode ： Mode 1: Transmit Description： Front View of Conducted Emission Test Setup Test Mode ： Mode 1: Transmit Description： Back View of Conducted Emission Test Setup Report No：113401R-RFUSP37V02 Page: 36 of 79 4.7. Test Photo Test Mode ： Mode 1: Transmit Description： Front View of Radiated Emission Test Setup (Bi-Log) Test Mode ： Mode 1: Transmit Description： Back View of Radiated Emission Test Setup (Bi-Log) Report No：113401R-RFUSP37V02 Page: 37 of 79 Test Mode ： Mode 1: Transmit Description： Front View of Radiated Emission Test Setup (Horn)