SO7-209L0000Blind/Shade Wireless Sensor Controller

Pella ® Insynctive ® Product Guide Pella ® Lifestyle Series Motorized, Integrated Blinds and Shades Pella ® Lifestyle Series Motorized, Integrated Blinds and Shades with Insynctive | 2Pella ® Lifestyle Series Motorized, Integrated Blinds and Shades with Insynctive | 3 Table of Contents 4 General and Safety Information Need Help? H ave a Home Automation System? W arnings 5 Product Overview Specifications 6 Detailed Instructions Setting Up Pella® Lifestyle Series Motorized, Integrated Blinds or Shades P rogramming Positions O perating Blinds or Shades with Remote T ilting Blind Slats P airing to Pella Bridge W ith Home Automation 12 Additional Instructions Charging Battery in Blinds or Shades C are and Maintenance R eplacing Batteries A dding or Deleting a Remote “ Homing” Blinds or Shades Re setting to Factory Defaults 15 Troubleshooting 16 FCC Compliance and Industry Canada Limited Warranty NEED HELP? For instant access to warranties, troubleshooting information and videos, visit Pella.CustHelp.com or call 855-473-5524. HAVE A HOME AUTOMATION SYSTEM? To view a list of compatible systems and contact your home automation provider for further information, visit ConnectPella.com. Failure to adhere to the warnings below may result in death, serious injury and/or loss of valuables. • Pella ® BLINDS and SHADES with Insynctive ® technology are not 100% reliable for a variety of reasons. For example, BLINDS and SHADES with Insynctive technology: — communicate data wirelessly, and wireless data is susceptible to interference or failure. — require proper installation. — require a battery with an adequate charge. — may be damaged after installation. Therefore, Pella Insynctive products should not be relied upon in situations where life, safety, and/or protection of valuables are solely dependent on their function. Test each product at least once per year to help ensure proper operation. • Pella Insynctive products are not a substitute for careful adult supervision of children. • Keep battery and other small parts out of reach of children. If small parts are swallowed, immediately seek medical help. • Batteries carry the risk of fire, explosion and burns. Do not disassemble or incinerate. WARNINGS General and Safety Information Pella ® Lifestyle Series Motorized, Integrated Blinds and Shades with Insynctive | 4Pella ® Lifestyle Series Motorized, Integrated Blinds and Shades with Insynctive | 5 SPECIFICATIONS Frequency: 433.92 MHz (Insynctive ® ) Operating Temperature: 32° – 120°F (0° – 49°C) Operating Humidity: 5% – 95% RH noncondensing Battery: Rechargeable Lithium Ion battery pack Typical Battery Life: 8 years (may vary with use) PELLA® LIFESTYLE SERIES MOTORIZED, INTEGRATED BLINDS or SHADES help to improve the comfort and convenience of your home. BLIND or SHADE may be controlled with a remote, app or a compatible home automation system. The slats of BLIND may be tilted to control privacy or the amount of light entering a room. BLIND or SHADE includes a power unit which is located at the bottom of the Hinged Glass Panel (HGP) and contains a rechargeable battery. The battery can be charged by: 1) the solar panel on the exterior side of the unit, requiring approximately 3 hours of direct sunlight a day, OR 2) a Pella Lifestyle Series WALL CHARGER that magnetically couples to the HGP. A wire provides power from the battery to the motor located in the headrail of BLIND or SHADE. Product Overview DETAILED INSTRUCTIONS 1. Get star ted. • To unpack BLIND or SHADE, remove the cardboard corner protector and bands that secure BLIND or SHADE. It is not necessary to open the Hinge Glass Panel (HGP) to unpack your BLIND or SHADE. • Unpack REMOTE. 2. P repare SINGLE-CHANNEL REMOTE. • Slide the battery cover in the direction of the arrow on the cover. • Remove battery tab. • Ensure battery is fully seated. • Slide the battery cover back into closed position. 3. P air REMOTE to Pella Lifestyle Series motorized BLIND or SHADE. • Hold REMOTE up to top cover approximately 6" from the end to activate pair mode. Move remote from side to side while pressed up against the glass. BLIND or SHADE will make a quick up/down motion to indicate it’s in pair mode. • Press and hold the Up button on REMOTE until BLIND or SHADE completes a quick up/down motion. NOTE: Up/down motion confirms that REMOTE was successfully paired. UP BUTTON DOWN BUTTON LED LIGHT CENTER BUTTON COVER REMOTE MEASURE 6" FROM END WHERE WIRE CONNECTS VIEW WITH HGP CLOSED Pella ® Lifestyle Series Motorized, Integrated Blinds or Shades the solar panel on the exterior side of the unit, requiring approximately 3 hours of direct sunlight a day, OR a Pella Lifestyle Series WALL CHARGER that magnetically couples to the HGP. A wire provides power from the battery to the motor located in the headrail of BLIND or SHADE. Pella ® Lifestyle Series Motorized, Integrated Blinds and Shades with Insynctive | 6Pella ® Lifestyle Series Motorized, Integrated Blinds and Shades with Insynctive | 7 4. Test BLIND or SHADE. • Press the Down button to move BLIND or SHADE down. • Press the Up button to move BLIND or SHADE up. 5. Set up BLIND or SHADE. Complete the following steps to set up BLIND or SHADE. Program upper position. • Touch the top end of REMOTE to BLIND or SHADE cover approximately 6” from the end where the wire connects. Move REMOTE back and forth slowly until BLIND or SHADE completes a quick up/down motion to indicate BLIND or SHADE has entered program mode. • Simultaneously press and hold the Center and Up buttons until BLIND or SHADE completes a quick up/down motion. This will require the buttons to be pressed for about 5 seconds. The light on REMOTE will begin blinking when the buttons are released to acknowledge that REMOTE is in program mode. • Press the Up or Down button on REMOTE to move BLIND or SHADE bottom rail to the desired position. • Press and hold the Center button until BLIND or SHADE makes a quick up/down movement. This should take about 3 seconds. Th…

Text truncated - open the document above for the full version.

Date: 7/5/2020 UL Verification Services Inc. 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern: I, the undersigned, hereby authorize UL Verification Services Inc. to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL Verification Services Inc. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing UL Verification Services Inc. as our representative, we still recognize that we are responsible to: a) fulfill the requirements for the scope of certification requested, including implementing any appropriate changes requested by UL Verification Services Telecommunications Certification Body (TCB) and / or the FCC; b) supply any and all information needed for the evaluation of the products for which certification is sought; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) not use our product certification in such a manner as to bring the TCB or FCC into disrepute and to not make any statement regarding product certification which the TCB or FCC may consider misleading or unauthorized; e) discontinue use of all advertising matter that contains any reference thereto and complies with any and all actions required by the FCC upon suspension or cancellation of certification; f) use certification only to indicate that products are certified in conformity with specified standards; g) endeavor to ensure that no certificate or report or any part thereof is used in a misleading manner, and any copies of the grants/certificates shall be reproduced in their entirety; h) comply with the requirements of the TCB and FCC, including the use of marks and label information prescribed for the scope of certification, when making reference to product certification in communication media such as documents, brochure or advertisements; i) comply with the requirements for certification, supply any information needed for evaluation of products to be certified and, where applicable, make provision for the participation of observers; j) ensure that products marketed under the scope of the requested certification continue to comply with the certification requirements; k) provide a sample of a production unit for testing within 30 days of the request should this product be selected as part of either the TCB’s or the FCC’s market surveillance requirements; l) keep a record of all complaints relating to product’s compliance with requirements of relevant standard; make records available to UL or FCC when requested; take appropriate action with respect to such complaints and any deficiencies found in the product that affect compliance with requirements for certification; document the actions taken with respect to complaints and/or deficiencies; m) inform the TCB immediately of any changes that may affect its ability to comply with the certification requirements. This authorization is valid until further written notice from the applicant July 05, 2021. Sincerely Yours, Dan Parrish Engineering Manager - Design Assurance/Gov'!Affairs/Chief Safety Pella Corporation

Label Format And Location Pella Corp Model # 209L0000 Figure 1: Location of Label on device exterior LABEL Figure 2: Label Format Dimensions: 22mm X 10mm Pella Corp Shade Drive Assembly Model#: 209L0000 FCC ID: SO7-209L0000 IC: 11009A-209L0000

NVLAP LAB CODE 200065-0 TEST REPORT Report Number. : 13310303-E1V2 Applicant : Pella Corporation 102 Main St. Pella, IA 50009 FCC ID ISED Model Number : : : SO7-209L0000 11009A-209L0000 209L0000 EUT Description : Blind/Shade Wireless Sensor Controller Test Standard(s) : FCC 47 CFR PART 15 SUBPART C INDUSTRY CANADA RSS 210 INDUSTRY CANADA RSS-GEN Issue 5 Date Of Issue: July 29, 2020 Prepared by: UL Verification Services Inc. 47173 Benicia Street Fremont, CA 94538 U.S.A. TEL: (510) 319-4000 FAX: (510) 661-0888 REPORT NO: 13310303-E1V2 DATE: JULY 29, 2020 FCC ID: SO7-209L0000 IC: 11009A-209L0000 Page 2 of 31 UL VERIFICATION SERVICES INC 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 319-4000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc.. Revision History Rev. Issue Date Revisions Revised By V1 06/3/2020 Initial Issue - V2 07/29/2020 Updated Section 1,2,7.1,7.2, 8, 9 and added Section 7.3 & Removed Section 7.4. K.Kedida REPORT NO: 13310303-E1V2 DATE: JULY 29, 2020 FCC ID: SO7-209L0000 IC: 11009A-209L0000 Page 3 of 31 UL VERIFICATION SERVICES INC 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 319-4000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc.. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS ..................................................................................4 2. TEST METHODOLOGY ......................................................................................................5 3. FACILITIES AND ACCREDITATION ..................................................................................5 4. CALIBRATION AND UNCERTAINTY .................................................................................6 4.1. MEASURING INSTRUMENT CALIBRATION ...............................................................6 4.2. SAMPLE CALCULATION .............................................................................................6 4.3. MEASUREMENT UNCERTAINTY ................................................................................6 5. EQUIPMENT UNDER TEST ................................................................................................7 5.1. DESCRIPTION OF EUT ...............................................................................................7 5.2. MAXIMUM FUNDAMENTAL FIELD STRENGTH ..........................................................7 5.3. DESCRIPTION OF AVAILABLE ANTENNAS ...............................................................7 5.4. SOFTWARE AND FIRMWARE .....................................................................................7 5.5. WORST-CASE CONFIGURATION AND MODE ...........................................................7 5.6. DESCRIPTION OF TEST SETUP .................................................................................8 6. TEST AND MEASUREMENT EQUIPMENT ........................................................................9 7. ANTENNA PORT TEST RESULTS ...................................................................................10 7.1. 20 dB AND 99% BW ...................................................................................................10 7.2. DUTY CYCLE .............................................................................................................13 7.3. TRANSMISSION TIME ...............................................................................................17 8. RADIATED EMISSION TEST RESULTS...........................................................................18 9. SETUP PHOTOS ...............................................................................................................27 REPORT NO: 13310303-E1V2 DATE: JULY 29, 2020 FCC ID: SO7-209L0000 IC: 11009A-209L0000 Page 4 of 31 UL VERIFICATION SERVICES INC 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 319-4000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc.. 1. ATTESTATION OF TEST RESULTS COMPANY NAME: Pella Corporation 102 Main St. Pella, IA 50009 EUT DESCRIPTION: Blind/Shade Wireless Sensor Controller MODEL: 209L0000 SERIAL NUMBER: 002, 004 DATE TESTED: APRIL 20 - MAY 18, 2020 2020 APPLICABLE STANDARDS STANDARD TEST RESULTS FCC PART 15 SUBPART C Pass INDUSTRY CANADA RSS-210 Issue 10, Annex A Pass INDUSTRY CANADA RSS-GEN Issue 5 Pass UL Verification Services Inc. tested the above equipment in accordance with the requirements set forth in the above standards. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein. It is the manufacturer's responsibility to assure that additional production units of this model are manufactured with identical electrical and mechanical components. All samples tested were in good operating condition throughout the entire test program. Measurement Uncertainties are published for informational purposes only and were not taken into account unless noted otherwise. This document may not be altered or revised in any way unless done so by UL Verification Services Inc. and all revisions are duly noted in the revisions section. Any alteration of this document not carried out by UL Verification Services Inc. will constitute fraud and shall nullify the document. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, any agency of the Federal Government, or any agency of the U.S. government. Approved & Released For UL Verification Services Inc. By: Reviewed By: Dan Coronia Kiya Kedida Operations Leader Senior Project Engineer Consumer Technology Division Consumer Technology Division UL Verification Services Inc. UL…

Text truncated - open the document above for the full version.

REPORT NO: 13310303-E1V2 DATE: JULY 29, 2020 FCC ID: SO7-209L0000 IC: 11009A-209L0000 Page 27 of 31 UL VERIFICATION SERVICES INC 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 319-4000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc.. 9. SETUP PHOTOS RADIATED EMISSION FOR PORTABLE CONFIGURATION PORTABLE CONFIGURATION – X ORIENTATION PORTABLE CONFIGURATION – Y ORIENTATION REPORT NO: 13310303-E1V2 DATE: JULY 29, 2020 FCC ID: SO7-209L0000 IC: 11009A-209L0000 Page 28 of 31 UL VERIFICATION SERVICES INC 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 319-4000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc.. PORTABLE CONFIGURATION – Z ORIENTATION REPORT NO: 13310303-E1V2 DATE: JULY 29, 2020 FCC ID: SO7-209L0000 IC: 11009A-209L0000 Page 29 of 31 UL VERIFICATION SERVICES INC 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 319-4000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc.. RADIATED EMISSION BELOW 30 MHz RADIATED EMISSIONS BELOW 30MHz (FRONT) RADIATED EMISSIONS BELOW 30MHz (BACK) REPORT NO: 13310303-E1V2 DATE: JULY 29, 2020 FCC ID: SO7-209L0000 IC: 11009A-209L0000 Page 30 of 31 UL VERIFICATION SERVICES INC 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 319-4000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc.. RADIATED EMISSION ABOVE 30 MHz RADIATED EMISSIONS ABOVE 30 MHz (FRONT) RADIATED EMISSIONS ABOVE 30 MHz (BACK) REPORT NO: 13310303-E1V2 DATE: JULY 29, 2020 FCC ID: SO7-209L0000 IC: 11009A-209L0000 Page 31 of 31 UL VERIFICATION SERVICES INC 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 319-4000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc.. RADIATED EMISSION ABOVE 1 GHz END OF REPORT RADIATED EMISSIONS ABOVE 1000 MHz (BACK) RADIATED EMISSIONS ABOVE 1000 MHz (FRONT)