SRFBCBTH200Headset with Bluetooth Technology

03 Bluetooth Headset BTH-200 User Manual 04 English 4.CHANGE THE INSTRUCTION 5. TURN THE HEADSET ON/OFF 5.1 To turn the headset on Pr ess and hold the answer / cancel call button 3 seconds until you see a quick flash of blue LED light. After that the LED will flash ever y two seconds. (When battery is low it will flash red indicator light) 5.2 To turn the headset off Pr ess and hold the answer / cancel call button 3 seconds until you hear tw o short tones followed by three quick flash of red indicator light then stop flash. The headset switches off and LED will stop flash. 1.3 Product Features Bluetooth Technology up to 10 meters wireless transmission range Direct answers remote voice dialing Rechargeable battery Adjustable ear hook for both right-ear listener or left-ear listener Compatible with the most Bluetooth enabled cellular phones Headset profile and hands-free profile. 1.4 How to Start Befor e you can use your headset you must first: Charge the headset battery, using an appropriate charger Pair the headset with a device for example, a mobile phone. 2.CHARGING The headset comes with a built-in rechargeable battery. To fully charge the battery f or first time, it will take up to 4 hours, after that it takes 2 hours to get fully recharge. The talking time for a fully charge battery is 3.5 hours, standby time is up to 100 hours. When the battery is charging, the LED indicator shows a steady blue light. Charge the headset battery, using pr ovided charger. Use other charger may damage the battery and headset. 3.WEARING THE HEADSET The design of the Bluetooth Headset is ver y flexible and convenient. The factory defaults and the instructions in this manual are f or wearing the headset on the right/left ear. F ollow these steps: Pull the ear hookPoint the microphone to ward your mouth. Loop the ear hook behind your ear as show and press the headset to your ear. 1 Start change over . 2 Remove rubber cushion. 3 Remove hook. 4 Change the way r eplace on the Bluetooth headset. 5 Replace rubber cushion on. 6 2 3 Remove Bluetooth headset from either side of ear. 1 Complete the exchange. Put on ear. 7 05 Bluetooth Headset BTH-200 User Manual 06 English 6. PAIRING Befor e the headset can be used with your mobile phone, it must first be paired. This process registers the headset and your mobile phone to each other. Pairing is necessary to establish a connection between Bluetooth enable devices. Your headset only needs to be paired once with each mobile phone that you use; however , its unique design enables you to pair it with other mobile phones. After pairing, y ou can use the headset to receive and initiate phone calls without additional configuration. 6.1 Pairing the headset with a phone The Bluetooth Headset has passed the compatibility test and can be used with most mobile phones from Nokia, Sony Ericsson, Siemens, Motorola and Philips. Once you have hair your headset with the phone, y ou do not need to pair it again. (Note: Except Nokia Phone) 1. After turning on the headset, continue pressing the talk key down until the both red and blue LED flashing, indicating the headset is ready to be connected to the wireless device for the first time. 2. Select “Bluetooth” on your mobile phone. 3. Select “Search for devices”. 4. Select”cellbird” from the option list; “Connecting to...”appears on the screen. Select “Enter Pass code”. 5. Enter “0000” (the default pass code for Cellbird), and then press “OK”. You can see the Blue LED light will quick flash twice ever y two second once the pairing is successful Note: If your headset doesn’t set under the pair mode, your Bluetooth mobile phone will not be able to find the headset, so the headset must set on the pairing mode. If the headset doesn’t pair up with mobile phone within one minute, the headset will turn off automatically, the previous pair will not work, you will need to repeat steps from 1 to 3 until it success. 7. MAKING AND ANSWERING CALLS Once you have success to pair the headset with your phone, y ou can make and receive calls using the headset as long as it is turned on and with in range of the phone. F or best performance, use the headset and phone in the same room. 7.1 To make a call using voice dialing If your mobile phone supports the voice dialing function, y ou can make a voice call through the headset. Sa y a name or voice command to place a phone call. This function is especially convenient and safe when you ar e driving. However , it depends on your mobile phone supporting function. Refer to the mobile phone’s user manual to see if the voice dialing function is supported. 7.2 To make a call using number pad You can place a phone call with your headset linked to your mobile phone. Use your mobile phone to dial the desired number, and then use the Bluetooth Headset to talk and listen to the caller. If you want to use your mobile phone to talk / listen, disconnect the paired link between the headset and the mobile phone. 7.3 To answer a call using the call handling button When the headset rings, press the call handling button. To adjust volume press + to increase volume or press – to decrease volume. End the call by pressing the call handling button. 7.4 To activate/cancel mute function Pr ess volume + and – at the same time for two seconds will activate mute function. Pr ess volume + or volume – for over two second will cancel the mute function. 7.5 To reject a call When the headset rings, press and hold the call handling button until you hear a long beep. 7.6 To adjust the volume You can adjust the headset speaker volume during a call or the ring volume when you are not engaged in a call. To increase/decrease the volume, press +/-

Apr.18, 2005 Federal Communications Commission Authorization and Evaluation Division FCC ID: SRFBCBTH200 Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: 1. Schematics 2. Block Diagram 3. Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Anne Chen _____________________________ Anne Chen /Product Marketing Manager BeCell Innovations Corp.

REPORT NO: ER/2005/30034 ID: SRFBCBTH200 DATE: Apr. 29, 2005 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw 0513 ILAC MRA APPENDIX 2 PHOTOGRPHS OF EUT REPORT NO: ER/2005/30034 ID: SRFBCBTH200 DATE: Apr. 29, 2005 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw 0513 ILAC MRA All View of EUT Front View of EUT REPORT NO: ER/2005/30034 ID: SRFBCBTH200 DATE: Apr. 29, 2005 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw 0513 ILAC MRA Back View of EUT Tip View of EUT

FCC ID LABEL FORMAT AND LOCATION Applicant: BeCeII Innovations Corp. FCC ID: SRFBCBTH200 FCC ID: SRFBCBTH200 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID LABEL AREA

REPORT NO: ER/2005/30034 ID: SRFBCBTH200 DATE: Apr. 29, 2005 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw 0513 ILAC MRA APPENDIX 3 PHOTOGRPHS OF EUT REPORT NO: ER/2005/30034 ID: SRFBCBTH200 DATE: Apr. 29, 2005 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw 0513 ILAC MRA Open View of EUT Internal of EUT REPORT NO: ER/2005/30034 ID: SRFBCBTH200 DATE: Apr. 29, 2005 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw 0513 ILAC MRA Internal of EUT Internal of EUT ANT REPORT NO: ER/2005/30034 ID: SRFBCBTH200 DATE: Apr. 29, 2005 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw 0513 ILAC MRA Internal of EUT Internal of EUT

REPORT NO: ER/2005/30034 ID: SRFBCBTH200 DATE: Apr. 29, 2005 Page: 1 of 54 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw 0513 ILAC MRA ELECTROMAGNETIC EMISSIONS COMPLIANCE REPORT INTENTIONAL RADIATOR CERTIFICATION TO FCC PART 15 SUBPART C REQUIREMENT OF Product Name: Headset with Bluetooth Technology Brand Name: N/A Model Name: BTH-200 Model Differences: N/A FCC ID: SRFBCBTH200 Report No.: ER/2005/30034 Issue Date: Apr. 29, 2005 FCC Rule Part: §15.247 Prepared for: BeCell Innovations Corp. 12F-9 No.79, Shin-Tai 5th Rd Sec 1, Shih-Chih, Taipei 221, Taiwan. Prepared by: SGS Taiwan Ltd. No. 134, Wu Kun g Rd., Wuku Industrial Zone, Taipei County, Taiwan. Note: This report shall not be reproduced except in full, without the written approval of SGS Taiwan Ltd. This document may be altered or revised by SGS Taiwan Ltd. personnel only, and shall be noted in the revision section of the document. REPORT NO: ER/2005/30034 ID: SRFBCBTH200 DATE: Apr. 29, 2005 Page: 2 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw 0513 ILAC MRA VERIFICATION OF COMPLIANCE Applicant: BeCell Innovations Corp. 12F-9 No.79, Shin-Tai 5th Rd Sec 1, Shih-Chih, Taipei 221, Taiwan. Equipment Under Test: Headset with Bluetooth Technology Brand Name: N/A FCC ID Number: SRFBCBTH200 Model No.: BTH-200 Model Difference: N/A File Number: ER/2005/30034 Date of test: Mar. 22, 2005 ~ Apr. 28, 2005 Date of EUT Received: Mar. 21, 2005 We hereby certify that: The above equipment was tested by SGS Taiwan Ltd. The test data, data evaluation, test proce- dures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4 (2003) and the energy emitted by the sample EUT tested as described in this report is in compliance with conducted and radiated emission limits of FCC Rules Part 15.247 The test results of this report relate only to the tested sample identified in this report. Test By: Date Apr. 29, 2005 Henk Huang Prepared By: Date Apr. 29, 2005 Gigi Yeh Approved By: Date Apr. 29, 2005 Vincent Su REPORT NO: ER/2005/30034 ID: SRFBCBTH200 DATE: Apr. 29, 2005 Page: 3 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw 0513 ILAC MRA Table of Contents 1. GENERAL INFORMATION .........................................................................................................6 1.1. Product Description ............................................................................................................................6 1.2. Related Submittal(s) / Grant (s) ..........................................................................................................6 1.3. Test Methodology ...............................................................................................................................6 1.4. Test Facility.........................................................................................................................................6 1.5. Special Accessories .............................................................................................................................6 1.6. Equipment Modifications....................................................................................................................6 2. SYSTEM TEST CONFIGURATION ............................................................................................7 2.1. EUT Configuration .............................................................................................................................7 2.2. EUT Exercise ......................................................................................................................................7 2.3. Test Procedure.....................................................................................................................................7 2.4. Configuration of Tested System..........................................................................................................8 3. SUMMARY OF TEST RESULTS .................................................................................................9 4. DESCRIPTION OF TEST MODES ..............................................................................................9 5. CONDUCTED EMISSION TEST................................................................................................10 5.1. Standard Applicable ..........................................................................................................................10 5.2. EUT Setup.........................................................................................................................................10 5.3. Measurement Procedure....................................................................................................................10 5.4. Measurement Equipment Used: ........................................................................................................11 5.5. Measurement Result.....................................................................................................…

Text truncated - open the document above for the full version.

REPORT NO: ER/2005/30034 ID: SRFBCBTH200 DATE: Apr. 29, 2005 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw 0513 ILAC MRA APPENDIX 1 PHOTOGRPHS OF SET UP REPORT NO: ER/2005/30034 ID: SRFBCBTH200 DATE: Apr. 29, 2005 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw 0513 ILAC MRA Radiated Emission Set up Photo REPORT NO: ER/2005/30034 ID: SRFBCBTH200 DATE: Apr. 29, 2005 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Taiwan Ltd. No. 134, Wu Kung Rd., Wuku Industrial Zone, Taipei Country, Taiwan. / 台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3939 f (886-2) 2298-2698 www.sgs.com.tw 0513 ILAC MRA Conducted Emission Set up Photo Conducted Emission Set up Photo