STQIPN00Airplay2 FM Transmitter IPN-APL-00/10

      Model: FM-368/IPN-APL-00/10 Description: FM Transmitter Date: 1.Nov.2005 Operation Plug in to iPod – Initialize communication, request power, etc. Turn on LCD temporarily. If music playing, start transmitting. If not, then sleep. AT ALL TIMES, DISPLAY XTREMEMAC LOGO Click 1, 2, or 3 – select preset – defaults should be set to 88.1, 98.1, 107.9 for US frequency range. Press and Hold 1, 2, 3 for 3 seconds and the current frequency is stored in memory as a preset and then 1, 2 or 3 is displayed PLUS THE WORD PRESET. Click Mode (bottom button) and the unit enters manual tuning mode, the frequency flashes AND THE WORD TUNE IS DISPLAYED and clicking < or > steps through lower or higher frequencies. Pressing and holding < or > scrolls the frequency down or up and after 2 seconds the scrolling rate doubles. After 3 additional seconds, the scrolling rate doubles again. When scrolling stops or when each step occurs, the current frequency shall become the new transmit frequency. After 20 seconds of no button presses, or if Mode is clicked again, the unit exits tuning mode. If, at anytime, the manual tuning results in an already preset frequency being selected, the number of the preset shall be displayed AND THE WORD PRESET. Press and hold the mode button for 3 seconds and the unit enters programming mode 1. Programming mode 1 is for the selection of the STEREO / MONO mode. When this mode is entered, the current setting (default is STEREO) is displayed flashing USING BOTH SPEAKER SYMBOLS if STEREO or THE RIGHT SPEAKER SYMBOL ONLY IF MONO. If mode is pressed the unit exits programming mode. If 2 is pressed, nothing happens. If 1 or 3 is pressed the unit displays the other setting (flashing). In other words, the 1 and 3 buttons cycle between the two settings. If the mode button is pressed, the unit exits programming mode with the current setting. If the mode button is held for 3 seconds while in programming mode 1, the unit exits programming mode. After 20 seconds, exit programming mode.       FCC STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the manufacturer could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.

FCC ID: STQIPN00 Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 20 Front View FCC ID: STQIPN00 Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 21 Rear View

FCC ID: STQIPN00 Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 8 2. PRODUCT LABELING Figure 2.2 Location of Label on the Side of EUT Figure 2.1 FCC ID Label (Statement may be shown in user manual) Figure 2.2 FCC ID Label Location FCC ID: STQIPN00 This device complies with part 15 of the FCC Rules. Operating is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Label

FCC ID: STQIPN00 Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 22 Open View FCC ID: STQIPN00 Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 23 Component Side/Open FCC ID: STQIPN00 Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 24 Foil Side/PCB

ELECTROMAGNETIC EMISSION COMPLIANCE REPORT of AIRPLAY2 FM TRANSMITTER MODEL: IPN-APL-00/10 FCC ID: STQIPN00 November 1, 2005 This report concerns (check one): Original grant x Class II change Equipment type: Low Power Intentional Radiator Deferred grant requested per 47 CF 0.457(d)(1)(ii)? yes no x If yes, defer until: (date) Company agrees to notify the Commission by (date) of the intended date of announcement of the product so that the grant can be issued on that date. Transition Rules Request per 15.37? yes no x If no, assumed Part 15, Subpart B for unintentional radiators - the new 47 CFR [10-1-90 Edition] provision. Report prepared for: Xtreme Accessories LLC. Report prepared by: Advanced Compliance Lab Report number: 0048-051028-01 The test result in this report IS supported and covered by the NVLAP accreditation 6 Randolph Way Hillsborough, NJ 08844 Tel: (908) 927 9288 Fax: (908) 927 0728 Advanced Compliance Lab FCC ID: STQIPN00 Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 2 Table of Contents Report Cover Page .........................................................................................................1 Table of Contents ...........................................................................................................2 Figures.............................................................................................................................3 1. GENERAL INFORMATION ...................................................................................4 1.1 Verification of Compliance .........................................................................4 1.2 Equipment Modifications............................................................................5 1.3 Product Information....................................................................................6 1.4 Test Methodology.........................................................................................6 1.5 Test Facility ..................................................................................................6 1.6 Test Equipment ............................................................................................6 1.7 Statement of the Document Use..................................................................7 2. PRODUCT LABELING............................................................................................8 3. SYSTEM TEST CONFIGURATION ......................................................................9 3.1 Justification ..................................................................................................9 3.2 Special Accessories.......................................................................................9 3.3 Configuration of Tested System .................................................................9 4. SYSTEM SCHEMATICS .........................................................................................12 5. RADIATED EMISSION DATA ...............................................................................13 5.1 Field Strength Calculation ..........................................................................13 5.2 Test Methods and Conditions .....................................................................13 5.3 Test Data .......................................................................................................14 5.4 Occupied Bandwidth ...................................................................................17 6. PHOTOS OF TESTED EUT ....................................................................................19 FCC ID: STQIPN00 Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 3 Figures Figure 2.1 FCC ID Label..............................................................................................8 Figure 2.2 Location of Label on Back of the EUT ......................................................8 Figure 3.1 Radiated Test Setup, Position X.................................................................10 Figure 3.2 Radiated Test Setup, Position Y.................................................................10 Figure 3.3 Radiated Test Setup, Position Z .................................................................11 Figure 4.1 EUT Schematics ...........................................................................................12 Figure 5.1 Bandwidth Plot ............................................................................................18 Figure 6.1 Front View....................................................................................................20 Figure 6.2 Rear View .....................................................................................................21 Figure 6.3 Inside View, Cover Opened ........................................................................22 Figure 6.4 Component Side ...........................................................................................23 Figure 6.5 Foil Side ........................................................................................................24 FCC ID: STQIPN00 Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 4 1. GENERAL INFORMATION 1.1 Verification of Compliance EUT: AIRPLAY2 FM TRANSMITTER Model: IPN-APL-00/10 Applicant: Xtreme Accessories LLC. 15751 SW 41 Street, #100 Fort Lauderdale FL 33331 Test Type: FCC Part 15C CERTIFICATION Result: PASS Tested by: ADVANCED COMPLIANCE LABORATORY Test Date: November 1, 2005 Report Number: 0048-051028-01 The above equipment was tested by Compliance Laboratory, Advanced Technologies, Inc. for compliance with the requirement set forth in the FCC rules and regulations Part 15 subpart C. This said equipment in the configuration described in the report, shows the maximum emission levels emanating from equipment are within the compliance requirements. The …

Text truncated - open the document above for the full version.

FCC ID: STQIPN00 Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 10 Figure 3.1 Radiated Test Setup-Position X Figure 3.2 Radiated Test Setup-Position Y FCC ID: STQIPN00 Advanced Compliance Lab, 6 Randolph Way, Hillsborough, NJ 08844 Tel: (908) 927-9288 Fax: (908) 927-0728 11 Figure 3.3 Radiated Test Setup-Position Z