SWX-AMGPROairGateway PRO

Model: AMG-PRO Quick Start Guide Hardware Overview To p RJ45 Connector (Male) LED POE Port LAN Port LED Steady White Power on and initializing Steady Blue Working properly and actively connected Alternating Blue/White Device is busy; do not touch or unplug. Bottom Reset Reset Ext Reset Buttons Reset To reset the airGateway ™ to factory defaults, press and hold the Reset button for more than 10 seconds while the airGateway is powered on. Reset Ext To reset the airMAX® device connected to the airGateway to factory defaults, press the Reset Ext button for about 8 seconds while the airMAX device is powered on. Installation WARNING: Do not connect non-PoE devices (such as laptops) to the POE port. To install the airGateway, perform the following steps: 1. Disconnect the Ethernet cables from the Ethernet ports on the PoE Adapter that is connected to your airMAX device. Ensure that you note which cable was connected to the POE port and which cable was connected to the LAN port. 2. Connect the male RJ45 Connector of the airGateway to the Ethernet port labeled POE on the PoE Adapter. 3. Connect the Ethernet cable that was disconnected from the POE port in step 1 to the Ethernet port labeled POE on the airGateway. 4. Connect the Ethernet cable that was disconnected from the LAN port in step 1 to the Ethernet port labeled LAN on the airGateway. Connecting via Wi-Fi To configure the airGateway, you must access it via Wi-Fi from a host machine. 1. Connect your host machine Wi-Fi to the wireless network (SSID) named www.ubnt.com Note: Ensure that you have DHCP enabled on your Wi-Fi adapter. 2. Launch a web browser and go to: https://192.168.1.1 3. The airOS® login screen will appear. Enter ubnt in the Username and Password fields. Upon initial login you must select your Country, Language, and agree to the Terms of Use to use the product. Click Login and the airGateway Setup Wizard will appear. Note: U.S. product versions are locked to the U.S. Country Code to ensure compliance with FCC regulations. 4. Change the default airGateway administrator password. Enter a new password in the New Password and Verify Password fields and click Next. 5. Enter a name for your wireless network (SSID) and a password (passphrase) for your wireless network. Click Next. 6. Verify your settings and click Finish or click Previous to change the settings. The airGateway is ready to use. Connect wireless clients as described for the appropriate operating system: Windows 8 1. On the Start screen, mouse over the lower right corner and click the settings icon when it appears. 2. Click the wireless icon. 3. Select the wireless network (SSID) that you defined in the airGateway Setup Wizard and then click Connect. 4. Enter the password defined in the airGateway Setup Wizard. Click Next. 5. Select your sharing option to finish setting up the connection. Mac 1. Click the AirPort icon in the menu bar (top right side of the screen). 2. Select the wireless network (SSID) that you defined in the airGateway Setup Wizard. 3. Enter the password defined in the airGateway Setup Wizard. Click OK. Once connected, the AirPort icon will change from gray to solid black. Safety Notices 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer. WARNING: Do not use this product in location that can be submerged by water. WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. Electrical Safety Information 1. Compliance is required with respect to voltage, frequency, and current requirements indicated on the manufacturer’s label. Connection to a different power source than those specified may result in improper operation, damage to the equipment or pose a fire hazard if the limitations are not followed. 2. There are no operator serviceable parts inside this equipment. Service should be provided only by a qualified service technician. 3. Contact a qualified electrician or the manufacturer if there are questions about the installation prior to connecting the equipment. 4. Protective earthing is provided by Listed AC adapter. Building installation shall provide appropriate short- circuit backup protection. 5. Protective bonding must be installed in accordance with local national wiring rules and regulations. Limited Warranty UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the product(s) furnished hereunder (the “Product(s)”) shall be free from defects in material and workmanship for a period of one (1) year from the date of shipment by UBIQUITI NETWORKS under normal use and operation. UBIQUITI NETWORKS’ sole and exclusive obligation and liability under the foregoing warranty shall be for UBIQUITI NETWORKS, at its discretion, to repair or replace any Product that fails to conform to the above warranty during the above warranty period. The expense of removal and reinstallation of any Product is not included in this warranty. The warranty period of any repaired or replaced Product shall not extend beyond its original term. Warranty Conditions The above warranty does not apply if the Product: (I) has been modified and/or altered, or an addition made thereto, except by Ubiquiti Networks, or Ubiquiti Networks’ authorized representatives, or as approved by Ubiquiti Networks in writing; (II) has been painted, rebranded or physically modified in any way; (III) has been damaged due to errors or defects in cabling; *640-00133-01* 640-00133-01 (IV) has been subjected to misuse, abuse, negligence, abnormal physical, electromagnetic or electrical stress, including lightning strikes, or accident; (V) has been damaged or impaired as a result of using third party firmware; (VI) has no original Ubiquiti MAC label, or is missing any other original Ubiquiti label(s); or (VII) has not been received by Ubiquiti within 30 days of issuance of the RMA. In addition, the above warranty shall apply only if: the product has been pr…

Text truncated - open the document above for the full version.

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 3.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Revised wording (obsolete) 1.0 2.0 Sept–25-2007 Updated company template (current) 2.0 3.0 Jan-31-2012 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 3.0 2015-4-20 To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Project and Product Certification Representative Authorization Letter We, _____ Ubiquiti Networks, Inc _____hereby authorize SIEMIC, INC. to act as a Certification Body for certifying for the following project(s): (Product description: airGateway PRO Model name: AMG-PRO FCC ID: SWX-AMGPRO Sincerely, Signature : Name and Job Title. : Ted Hsiao E-mail : [email protected] Tel. : (886)2-2758-1657 x144/107

SCS-F19: Confidentiality Request Letter Page 1 of 3 Rev 3.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Confidentiality Request Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Adding CFR 2.459 (obsolete) 1.0 2.0 August – 11 - 2008 Updated company template & Added text box (current) 2.0 3.0 Jan-31-2012 SCS-F19: Confidentiality Request Letter Page 2 of 3 Rev 3.0 2015-3-10 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Subject: Permanent Confidentiality Request for FCC ID: SWX-AMGPRO We hereby request confidential treatment of information accompanying this application as outlined below: - e.g. security form - e.g. Schematic - e.g. Block diagram - e.g. Operational description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Signature : Name and Job Title. : Ted Hsiao E-mail : [email protected] Tel. : (886)2-2758-1657 x144/107 SCS-F19: Confidentiality Request Letter Page 3 of 3 Rev 3.0 To: Federal Communications Commission Communications Commission Office of Engineering and Technology Equipment Authorization Division 7345 Oakland Mills Road Columbia, Maryland 21046 Subject: Short Term Confidentiality Request for FCC ID: SWX-AMGPRO To Whom It May Concern: Pursuant to sections 0.457 and 0.459 of CFR 47 and to avoid premature release of sensitive information prior to marketing or release of the product to the public, the applicant requests the following documents contained in this certification application be temporarily withheld from public disclosure for an initial period of 45 or 180 days (please check one). - User Manual - Internal Photo - External Photo - Test Setup Photo The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Sincerely, Signature : Signature : Name and Job Title. : Ted Hsiao E-mail : [email protected] Tel. : (886)2-2758-1657 x144/107

D ◆A ◆P ◆B ◆M Th e ma Declara Applicant: Product na Brand: UB Model: AM Series mo e two mod rketing re Signatu Name a Title. E‐mail Tel. ation Ubiquiti N ame: airG BIQUITI MG-PRO odel(1): A dels are id equiremen ure and Job of Mo Networks ateway P AMG-PRO entical ex nt. : : Ted Hs i : Ted.h : (886)2‐ odel D RO O-INS xcept for t iao siao@ub n ‐2758‐165 Differe he Model nt.com 57 x144/1 ences number d 07 s Lette due to er

Jan. 19, 2015 FCC Grantee code：SWX IC No：6545A Dear Sir, I hereby have entrusted the following person to be a proxy regarding applications for Type Certification. Ubiquiti Networks,Inc Address: 2580 Orchard Parkway, San Jose CA95131 Name: Ted Hsiao Job Title: Compliance Manager Email: [email protected] I am therefore responsible for the contents of Ubiquiti Networks, Inc. applications. FCC Grantee Code : SWX IC No：6545A Signature____________________ Mike Taylor Compliance Manager Ubiquiti Networks,Inc 2580 Orchard Parkway TEL: 408-942-3085 x442 FAX: 408-904-5225 [email protected]

Ubiquiti Networks, Inc. 2580 Orchard Parkway San Jose, CA 95131 To Whom it may concern, Professional Installation Justification: Ubiquiti Networks, Inc. declares that the AMG-PRO (FCC ID: SWX-AMGPRO) units are sold to wireless equipment providers and require a professional installation. The installers have to follow the assembly instruction and login to enable the radio. Let radio work at right condition. Ted Hsiao Ubiquiti Networks, Inc. Compliance Manager

1 of 8 External Photos Model Number: AMG-PRO ; AMG-PRO-INS FCC ID: SWX-AMGPRO IC ID: 6545A-AMGPRO 2 of 8 (1) EUT Photo (2) EUT Photo 3 of 8 (3) EUT Photo (4) EUT Photo 4 of 8 (5) EUT Photo (6) EUT Photo 5 of 8 (7) EUT Photo (8) EUT Photo 6 of 8 (9) EUT Photo (10) EUT Photo 7 of 8 (11) EUT Photo (12) EUT Photo 8 of 8 (13) EUT Photo

1 of 8 Internal Photos Model Number: AMG-PRO ; AMG-PRO-INS FCC ID: SWX-AMGPRO IC ID: 6545A-AMGPRO 2 of 8 EUT Photo 1 ) EUT Photo 2 ) Wi-Fi Antenna Wi-Fi Antenna 3 of 8 EUT Photo 3 ) EUT Photo 4 ) 4 of 8 EUT Photo 5 ) EUT Photo 6 ) 5 of 8 EUT Photo 7 ) EUT Photo 8 ) 6 of 8 EUT Photo 9 ) EUT Photo 10 ) 7 of 8 EUT Photo 11 ) EUT Photo 12 ) 8 of 8 EUT Photo 13 )

A Test Lab Techno Corp. Changan Lab：No. 140 -1, Changan Street, Bade City, Taoyuan County, Taiwan R.O.C. Te l：886-3-271-0188 / Fax：886-3-271-0190 MPE Report Test Report No. ： 1502FS12-02 Applicant ： Ubiquiti Networks,Inc Manufacturer ： Ubiquiti Networks,Inc Product Type ： airGateway PRO Trade Name ： UBIQUITI Model Number ： AMG-PRO, AMG-PRO-INS Date of Received ： Jan. 28, 2015 Test Period ： Feb. 06, 2015 Date of Issued ： Apr. 13, 2015 Test Specification ： 47 CFR § 2.1091 47 CFR §1.1310 ANSI / IEEE Std.C95.1-1992 Location of Test Lab. ： Chang-an Lab. 1. The test operations have to be performed with cautious behavior, the test results are as attached. 2. The test results are under chamber environment of A Test Lab Techno Corp. A Test Lab Techno Corp. does not assume responsibility for any conclusions and generalizations drawn from the test results with regard to other specimens or samples. 3. The measurement report has to be written approval of A Test Lab Techno Corp. It may only be reproduced or published in full. This report shall not be reproduced except in full, without the written approval of A Test Lab Techno Corp. 4. This document may be altered or revised by A Test Lab Techno. Corp. personnel only, and shall be noted in the revision section of the document. Approved By ： Tested By ： (Bill Hu) (Sky Chou) Report Number: 1502FS12-02Page 1 of 7 ©2015 A Test Lab Techno Corp. Contents 1. Description of Equipment under Test (EUT)............................................................... 3 2. Human Exposure Assessment .................................................................................... 4 3. RF Output Power........................................................................................................... 5 4. Test Result.....................................................................................................................7 Report Number: 1502FS12-02Page 2 of 7 ©2015 A Test Lab Techno Corp. 1. Description of Equipment under Test (EUT) Applicant Ubiquiti Networks,Inc Applicant Address 2580 Orchard Parkway, San Jose CA95131,USA Manufacturer Ubiquiti Networks,Inc Manufacturer Address 2580 Orchard Parkway, San Jose CA95131,USA Product Type airGateway PRO Trade Name UBIQUITI Model Number AMG-PRO, AMG-PRO-INS Different Description These model numbers differe from each other in selling region. Hardware Version 02024 Software Version V1.1 Radio Hardware Version DC3A Radio Software Version V1.1 FCC ID SWX-AMGPRO Frequency Range 2412 - 2462 MHz IEEE 802.11b / IEEE 802.11g 2412 - 2462 MHz IEEE 802.11n (2.4GHz) 20MHz 2422 - 2452 MHz IEEE 802.11n (2.4GHz) 40MHz 5180 - 5825 MHz IEEE 802.11a 5180 - 5825 MHz IEEE 802.11n (5GHz) 20MHz 5190 - 5795 MHz IEEE 802.11n (5GHz) 40MHz Transmit Power IEEE 802.11b: 0.142 W / 21.53 dBm (conducted power) IEEE 802.11g: 0.070 W / 18.44 dBm IEEE 802.11n (2.4GHz) 20MHz: 0.053 W / 17.22 dBm IEEE 802.11n (2.4GHz) 40MHz: 0.032 W / 15.04 dBm IEEE 802.11a: 0.078 W / 18.92 dBm IEEE 802.11n (5GHz) 20MHz: 0.072 W / 18.60 dBm IEEE 802.11n (5GHz) 40MHz: 0.046 W / 16.66 dBm Antenna Specification IEEE 802.11b, IEEE 802.11g: 1 dBi IEEE 802.11n (2.4GHz) 20MHz / 40MHz: 1 dBi IEEE 802.11a, IEEE 802.11n (5GHz) 20MHz / 40MHz: 2 dBi Antenna Designation PIFA Antenna RF Evaluation 0.40 W/m 2 The above equipment was tested by A Test Lab Techno Corp. For compliance with the requirements set forth in 47 CFR § 2.1091 & 47 CFR § 1.1310. The results of testing in this report apply only to the product/system, which was tested. Other similar equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties Report Number: 1502FS12-02Page 3 of 7 ©2015 A Test Lab Techno Corp. 2. Human Exposure Assessment Due to the design and installation of this product, it is not possible to conduct SAR evaluation. This is because client either manufactures or supplies the antenna(s) that will be used in the installation of this product. Therefore, this product will be evaluated as a mobile device per 47 CFR §1.1310 titled “Radiofrequency radiation exposure limits”, generally referred to as MPE limits. In 47 CFR § 2.1091, paragraph (b) defines a mobile device as “a transmitting device designed to be used in other than fixed locations and to generally be used in such a way that a separation distance of at least 20 cm is normally maintained between the transmitter’s radiating structure(s) and the body of the user or nearby persons. ” This product is intended to be installed into a vehicle such that the unit is physically secured at one location. In the installation guide supplied with the product, Client has made the following statement: “IMPORTANT: To meet the FCC’s RF Exposure Guidelines, the antenna should be installed so there is at least 20 cm of separation between the body of the user and nearby persons and the antenna”. Based on the installation of the transceiver and the antenna, the transmitters radiating structure is more than 20 cm from the user. Thus, this product is a “mobile device” as defined in section § 2.1091 paragraph (b). Exposure evaluation 2 4R PG S π = Where S: power density P: power input to the antenna G: power gain of the antenna in the direction of interest relative to an isotropic radiator. R: distance to the center of radiation of the antenna. Report Number: 1502FS12-02Page 4 of 7 ©2015 A Test Lab Techno Corp. 3. RF Output Power Band Data Rate CH Frequency (MHz) RF Power setting in Test Software Test Software Version 1 2412.0 17.00 6 2437.0 17.00 IEEE 802.11b 1M 11 2462.0 17.00 1 2412.0 13.50 6 2437.0 13.50 IEEE 802.11g 6M 11 2462.0 13.50 1 2412.0 12.50 6 2437.0 12.50 IEEE 802.11n (2.4GHz) 20MHz 19.5M 11 2462.0 12.50 3 2422.0 10.00 6 2437.0 10.00 IEEE 802.11n (2.4GHz) 40MHz 40.5M 9 2452.0 10.00 Atheros Radio Test 2 ART2-GUI Version:2.2 CART Version:2.54 Band Data Rate CH Frequency (MHz) RF Power setting in Test Software Test Software Version 36 5180.0 13.0 40 5200.0 13.0 44 5220.0 13.0 48 5240.0 13.0 14957…

Text truncated - open the document above for the full version.

FCC 47 CFR PART 15 SUBPART E Product Type ： airGateway PRO Applicant ： Ubiquiti Networks,Inc Address ： 2580 Orchard Parkway, San Jose CA95131,USA Trade Name ： UBIQUITI Model Number ： AMG-PRO, AMG-PRO-INS Test Specification ： FCC 47 CFR PART 15 SUBPART E: Oct., 2013 ANSI C63.10-2013 Application Purpose ： Original Receive Date ： Jan. 27, 2015 Test Period ： Feb. 01 ~ Feb. 03, 2015 Issue Date ： May 05, 2015 Issue by A Test Lab Techno Corp. No. 140-1, Changan Street, Bade City, Taoyuan County 334, Taiwan R.O.C. Te l：+86-3-2710188 / Fax：+86-3-2710190 T aiwan Accreditation Foundation accreditation number: 1330 Note: This report shall not be reproduced except in full, without the written approval of A Test Lab Techno Corp. This document may be altered or revised by A Test Lab Techno Corp. personnel only, and shall be noted in the revision section of the document. The client should not use it to claim product endorsement by TAF, or any government agencies. The test results in the report only apply to the tested sample. Report Number: 1502FR28-04 1 of 89 A Test Lab Techno Corp. Revision History Rev. Issue Date Revisions Revised By 00 Feb. 17, 2015 Initial Issue 01 Apr. 08, 2015 Revised report information. Peggy Chang 02 Apr. 13, 2015 Revised report information. Snow Wang 03 Apr. 29, 2015 Revised report information. Snow Wang 04 May 05, 2015 Revised report information. Snow Wang Report Number: 1502FR28-04 2 of 89 A Test Lab Techno Corp. Verification of Compliance Issued Date: 05/05/2015 Product Type : airGateway PRO Applicant : Ubiquiti Networks,Inc Address : 2580 Orchard Parkway, San Jose CA95131,USA Trade Name : UBIQUITI Model Number : AMG-PRO, AMG-PRO-INS FCC ID : SWX-AMGPRO EUT Rated Voltage : DC 24V, 0.5A Test Voltage : 120 Vac / 60 Hz Applicable Standard : FCC 47 CFR PART 15 SUBPART E: Oct., 2013 ANSI C63.10-2013 Test Result : Complied Application Purpose : Original Performing Lab. : A Test Lab Techno Corp. No. 140-1, Changan Street, Bade City, Taoyuan County 334, Taiwan R.O.C. Te l：+86-3-2710188 / Fax：+86-3-2710190 T aiwan Accreditation Foundation accreditation number: 1330 http://www.atl-lab.com.tw/e-index.htm A Test Lab Techno Corp. tested the above equipment in accordance with the requirements set forth in the above standards. All indications of Pass/Fail in this report are opinions expressed by A Test Lab Techno Corp. based on interpretations and/or observations of test results. Measurement Uncertainties were not taken into account and are published for informational purposes only. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Approved By ： Reviewed By ： (Manager) (Fly Lu) (Testing Engineer) (Eric Ou Yang) Report Number: 1502FR28-04 3 of 89 A Test Lab Techno Corp. TABLE OF CONTENTS 1 General Information................................................................................................................................. 6 1.1. Summary of Test Result................................................................................................................ 6 1.2. Measurement Uncertainty............................................................................................................. 6 2 EUT Description ....................................................................................................................................... 7 3 Test Methodology .................................................................................................................................... 8 3.1. Mode of Operation ........................................................................................................................ 8 3.2. EUT Exercise Software................................................................................................................. 8 3.3. Configuration of Test System Details ............................................................................................ 9 3.4. Test Site Environment ................................................................................................................... 9 4 AC Power Conducted Emission Measurement................................................................................... 10 4.1. Limit ............................................................................................................................................ 10 4.2. Test Instruments.......................................................................................................................... 10 4.3. Test Setup ................................................................................................................................... 10 4.4. Test Procedure............................................................................................................................ 11 4.5. Test Result .................................................................................................................................. 12 5 Radiated Emission Measurement ........................................................................................................ 14 5.1. Limit ............................................................................................................................................ 14 5.2. Test Instruments.......................................................................................................................... 14 5.3. Setup........................................................................................................................................... 15 5.4. Test Procedure............................................................................................................................ 17 5.5. Test Result .................................................................................................................................. 18 6 Maximum Conducted Output Power.........................................................…

Text truncated - open the document above for the full version.

Part 15E Test Setup Photographs Conducted Emissions Test Configuration: Front View Rear View Report Number: 1502FR28-03 1 of 3 A Test Lab Techno Corp. Radiated Emissions Test Configuration: Below 1GHz _ Front View Below 1GHz _ Rear View Report Number: 1502FR28-03 2 of 3 A Test Lab Techno Corp. Above 1GHz _ Front View Above 1GHz _ Rear View Report Number: 1502FR28-03 3 of 3 A Test Lab Techno Corp.