SWX-WAVEAPRDigital Transmission Radio

E-Label User Information FCC ID: SWX-WAVEAPR IC ID: 6545A-WAVEAPR Ubiquiti Inc. will be incorporating the E-Label procedures per FCC KDB 784748-D02. The information below is what will be included in the E-Labeling. E-label and warning statements can be found in the device/controller GUI under Device > Settings > About. Detailed compliance information including Declaration of Conformity is available at the following internet address: ui.com/compliance FCC Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generated, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operations of this equipment in a residential area is likely to cause harmful interference in which case the user bill be required to correct the interference at his own expense. ISED Canada CAN ICES-3 (A) / NMB-3 (A) This device complies with ISED Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. CAN ICES-3 (A) / NMB-3 (A) Le présent appareil est conforme aux CNR d’ISDE Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: 1. L’appareil ne doit pas produire de brouillage; 2. I’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. RF Exposure Warning The antennas used for this transmitter must be installed to provide a separation distance of at least 45 cm from all persons and must not be located or operating in conjunction with any other antenna or transmitter. Les antennes utilisées pour ce transmetteur doivent être installé en considérant une distance de séparation de toute personnes d’au moins 45 cm et ne doivent pas être localisé ou utilize en conflit avec tout autre antenne ou transmetteur.

685 3 RD AVE. • NEW Y0RK, NY 10071 • www.ui.com Date: 5/18/2022 TIMCO Engineering, Inc. 849 N.W. State Road 45 P.O. Box 370 Newberry, Florida 32669 RE: Request for Confidentiality In reference to the application under FCC ID: SWX-WAVEAPR, and pursuant to Sections 0.457(d)1(ii) and 0.459 of the Commission’s Rules, Ubiquiti Networks hereby requests permanent confidential treatment of the accompanying information as outlined below: Block Diagram Schematics Theory of Operation Software Security Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to Ubiquiti Networks and provide unjustified benefits to its competitors. In addition to the above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the important rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short term confidentiality on the following attachments until 180 days from grant date. External Photos Internal Photos Test Setup Photos User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondence during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Ubiquiti Networks understands that pursuant to Rule 0.457(d)(1)(ii), disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Mark Feil Ubiquiti lnc. Compliance Manager

Power of Attorney Date: 2021/01/20 Dear Sir or Madam, I hereby have entrusted the following entity to be an authorized agent regarding application for Type Certification. Ubiquiti Inc. also authorizes the following entity to be a proxy to handle all certification matters. Unified Compliance Laboratories Address : 427 W 128000 South Draper Utah 84020 e-mail : [email protected] Applicant : Ubiquiti Inc. Address : 685 Third Avenue ,New York NY 10017 United States Of America Name and Job Title. : Mark Feil / Compliance Director E-mail : [email protected] Tel. : 385-200-1617

427 West 12800 South, Draper, UT 84020 Photograph 1: Front View of DUT 427 West 12800 South, Draper, UT 84020 Photograph 2: Left/Back View of DUT 427 West 12800 South, Draper, UT 84020 Photograph 3: Top View of DUT 427 West 12800 South, Draper, UT 84020 Photograph 4: Bottom View of DUT 427 West 12800 South, Draper, UT 84020 Photograph 5: Back View of DUT Cover Removed Showing RF45 Jack 427 West 12800 South, Draper, UT 84020 Photograph 6: Right Side View of DUT 427 West 12800 South, Draper, UT 84020 Photograph 7: Left Side View of DUT

427 West 12800 South Draper, UT 84020 Test Report Annex Internal Photographs FCC ID SWX-WAVEAPR ISED ID 6545A-WAVEAPR Equipment Under Test Wave-APR Report Issue Date May 18, 2022 427 West 12800 South, Draper, UT 84020 Wave-AP_InternalPhotos Page 2 of 9 PROPRIETARY Bluetooth Antenna 427 West 12800 South, Draper, UT 84020 Wave-AP_InternalPhotos Page 3 of 9 PROPRIETARY 5 GHz Antenna 5 GHz Antenna 427 West 12800 South, Draper, UT 84020 Wave-AP_InternalPhotos Page 4 of 9 PROPRIETARY 427 West 12800 South, Draper, UT 84020 Wave-AP_InternalPhotos Page 5 of 9 PROPRIETARY 427 West 12800 South, Draper, UT 84020 Wave-AP_InternalPhotos Page 6 of 9 PROPRIETARY Bluetooth Connector 5 GHz Chain 1 Connector 5 GHz Chain 2 Connector 427 West 12800 South, Draper, UT 84020 Wave-AP_InternalPhotos Page 7 of 9 PROPRIETARY 427 West 12800 South, Draper, UT 84020 Wave-AP_InternalPhotos Page 8 of 9 PROPRIETARY 427 West 12800 South, Draper, UT 84020 Wave-AP_InternalPhotos Page 9 of 9 PROPRIETARY 60 GHz Antenna

§ 15.407(f) Maximum Permissible Exposure Test Requirement(s): §15.407(f): U-NII devices are subject to the radio frequency radiation exposure requirements specified in §1.1307(b), §2.1091 and §2.1093 of this chapter, as appropriate. All equipment shall be considered to operate in a “general population/uncontrolled” environment. RF Exposure Requirements: §1.1307(b)(1) and §1.1307(b)(2): Systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess of the Commission’s guidelines. RF Radiation Exposure Limit: §1.1310: As specified in this section, the Maximum Permissible Exposure (MPE) Limit shall be used to evaluate the environmental impact of human exposure to radiofrequency (RF) radiation as specified in Sec. 1.1307(b), except in the case of portable devices which shall be evaluated according to the provisions of Sec. 2.1093 of this chapter. MPE Limit: EUT’s operating frequencies @ UNII-1 5165 – 5240 MHz, UNII-3 5740 – 5835 MHz, BLE 2402 – 2480 MHz, 60 GHz Band 58320 – 70200 MHz; Limit for Uncontrolled exposure: 1 mW/cm 2 or 10 W/m 2 Equation from page 18 of OET 65, Edition 97-01 S = PG / 4πR 2 or R = √(PG / 4πS) where, S = Power Density (mW/cm 2 ) P = Power Input to antenna (mW) G = Antenna Gain (numeric value) R = Distance (cm) Test Results: FCC Frequency (MHz) Con. Pwr. (dBm) Con. Pwr. (mW) Ant. Gain (dBi) Ant. Gain numeric Pwr. Density (mW/cm 2 ) Limit (mW/cm 2 ) Margin Distance (cm) Result 2480* 7.66 5.83 2.0 1.59 0.00 1.0 -1.0 45 Pass 5240 27.20 524.81 12.0 15.85 0.16 1.0 -0.84 45 Pass 5790* 29.32 855.07 12.0 15.85 0.53 1.0 -0.47 45 Pass 69120* 16.43 43.95 24.0 251.19 0.43 1.0 -0.57 45 Pass *Simultaneous Transmission (Worse case): 0.96 1.0 -0.04 45 Pass The safe distance for SWX-WAVEAPR where Power Density is less than the MPE Limit listed above was found to be 45 cm.

427 West 12800 South Draper, UT 84020 Test Report Certification FCC ID SWX-WAVEAPR IC ID 6545A-WAVEAPR Equipment Under Test Wave-AP Test Report Serial Number TR5968_03 Date of Test(s) 3/12/2021 – 4/1/2021 Report Issue Date May 18, 2022 Test Specification Applicant 47 CFR FCC Part 15, Subpart C Ubiquiti Inc. 685 Third Avenue, 27 th Floor New York, NY 10019 U.S.A. NVLAP LAB CODE 600241-0 427 West 12800 South, Draper, UT 84020 TR5968_Wave-AP_FCC_15.255_03 Page 2 of 30 PROPRIETARY Certification of Engineering Report This report has been prepared by Unified Compliance Laboratory (UCL) to document compliance of the device described below with the requirement of Federal Communication Commissions (FCC) Part 15, Subpart C. This report may be reproduced in full. Partial reproduction of this report may only be made with the written consent of the laboratory. The results in this report apply only to the sample tested. Applicant Ubiquiti Inc. Manufacturer Ubiquiti Inc. Brand Name Ubiquiti Model Number Wave-AP FCC ID SWX-WAVEAPR IC ID 6545A-WAVEAPR On this 18 th day of May 2022, I individually and for Unified Compliance Laboratory certify that the statements made in this engineering report are true, complete, and correct to the best of my knowledge and are made in good faith. Although NVLAP has accredited the Unified Compliance Laboratory testing facilities, this report must not be used to claim product certification, approval, or endorsement by NVLAP, NIST or any agency of the U.S. federal government. Unified Compliance Laboratory Written By: Clay Allred Reviewed By: Richard L. Winter 427 West 12800 South, Draper, UT 84020 TR5968_Wave-AP_FCC_15.255_03 Page 3 of 30 PROPRIETARY Revision History Revision Description Date 01 Original Report Release 4/2/2021 02 Amend Brand Name and Company Address 8/2/2021 03 Updated FCC and IC ID 5/18/2022 427 West 12800 South, Draper, UT 84020 TR5968_Wave-AP_FCC_15.255_03 Page 4 of 30 PROPRIETARY Table of Contents 1 Client Information ................................................................................................................................. 5 1.1 Applicant ....................................................................................................................................... 5 1.2 Manufacturer ................................................................................................................................. 5 2 Equipment Under Test (EUT) ............................................................................................................... 6 2.1 Identification of EUT .................................................................................................................... 6 2.2 Description of EUT ....................................................................................................................... 6 2.3 EUT and Support Equipment ........................................................................................................ 6 2.4 Interface Ports on EUT ................................................................................................................. 7 2.5 Operating Environment ................................................................................................................. 7 2.6 Operating Modes ........................................................................................................................... 7 2.7 EUT Exercise Software ................................................................................................................. 7 2.8 Block Diagram of Test Configuration .......................................................................................... 8 2.9 Modification Incorporated/Special Accessories on EUT .............................................................. 8 2.10 Deviation, Opinions Additional Information or Interpretations from Test Standard .................... 8 3 Test Specification, Method and Procedures .......................................................................................... 9 3.1 Test Specification .......................................................................................................................... 9 3.2 Methods & Procedures .................................................................................................................. 9 3.3 FCC Part 15, Subpart C ................................................................................................................ 9 3.4 Results ......................................................................................................................................... 10 3.5 Test Location .............................................................................................................................. 10 4 Test Equipment ................................................................................................................................... 11 4.1 Conducted Emissions at Mains Ports .......................................................................................... 11 4.2 Radiated Emissions ..................................................................................................................... 11 4.3 Equipment Calibration ................................................................................................................ 13 4.4 Measurement Uncertainty ........................................................................................................... 13 5 Test Results ......................................................................................................................................... 14 5.1 §15.203 Antenna Requirements .................................................................................................. 14 5.2 Conducted Emissions at Mains Ports Data ................................................................................. 14 5.3 Emissions Bandwidth .................................................…

Text truncated - open the document above for the full version.

CONFIDENTIAL -INTERNAL USE ONLY [Wave-AP] antenna measurement CONFIDENTIAL -INTERNAL USE ONLY BT 1.Antenna type: printedPCB Z X Z Y Y X Z X Y Peak gain (dBi) 2440MHz2 CONFIDENTIAL -INTERNAL USE ONLY WiFi 1.Antenna type: Patch Z X Z Y Y X Z X Y Peak gain (dBi) 5200MHz10.6 5280MHz10.9 5620MHz11.8 5785MHz12 CONFIDENTIAL -INTERNAL USE ONLY WigigRadiation pattern 1.Antenna type: Dish 2.EIRP: 43 dBm 3.Gain: 24 dBi CONFIDENTIAL -INTERNAL USE ONLY GPS Z X Z YY X Peak gain (dBi) 1575MHz1.8 1.Antenna type: Dipole CONFIDENTIAL -INTERNAL USE ONLY

427 West 12800 South, Draper, UT 84020 Photograph 1: View Test Set Up Radiated Emissions 30 – 1000 MHz Photograph 2: View Test Set Up Radiated Emissions 1 – 17 GHz 427 West 12800 South, Draper, UT 84020 Photograph 3: View Test Set Up Radiated Emissions 17 – 40 GHz Photograph 4: View Test Set Up RF Conducted 427 West 12800 South, Draper, UT 84020 Photograph 5: Front View Test Set Up AC Mains Conducted Emissions Photograph 6: Back View Test Set Up AC Mains Conducted Emissions