SWX-XR22.4GHz mini-PCI 802.11b/g

XTREMERange2 OEM INTEGRATION GUIDE Carrier-Class 2.4GHz 802.11b/g Radio Module TECHNICAL SPECIFICATIONS XTREMERange2 DataRateTX PowerToleranceDataRateSensitivityTolerance 1Mbps26 dBm+/-1dB1Mbps-97 dBm+/-1dB 2Mbps26 dBm+/-1dB2Mbps-96 dBm+/-1dB 5.5Mbps26 dBm+/-1dB5.5Mbps-95 dBm+/-1dB 11Mbps26 dBm+/-1dB11Mbps-92 dBm+/-1dB 6Mbps26 dBm+/-1dB6Mbps-94 dBm+/-1dB 9Mbps26 dBm+/-1dB9Mbps-93 dBm+/-1dB 12Mbps26 dBm+/-1dB12Mbps-91 dBm+/-1dB 18Mbps26 dBm+/-1dB18Mbps-90 dBm+/-1dB 24Mbps26 dBm+/-1dB24Mbps-86 dBm+/-1dB 36Mbps24 dBm+/-1dB36Mbps-83 dBm+/-1dB 48Mbps23 dBm+/-1dB48Mbps-77 dBm+/-1dB 54Mbps22 dBm+/-1dB54Mbps-74 dBm+/-1dB DataRateCurrentToleranceDataRateSensitivityTolerance 1Mbps1.30 A+/-100mA1Mbps300 mA+/-100mA 2Mbps1.30 A+/-100mA2Mbps300 mA+/-100mA 5.5Mbps1.30 A+/-100mA5.5Mbps300 mA+/-100mA 11Mbps1.30 A+/-100mA11Mbps300 mA+/-100mA 6Mbps1.30 A+/-100mA6Mbps300 mA+/-100mA 9Mbps1.30 A+/-100mA9Mbps300 mA+/-100mA 12Mbps1.30 A+/-100mA12Mbps300 mA+/-100mA 18Mbps1.30 A+/-100mA18Mbps300 mA+/-100mA 24Mbps1.30 A+/-100mA24Mbps300 mA+/-100mA 36Mbps1.10 A+/-100mA36Mbps300 mA+/-100mA 48Mbps1.00 A+/-100mA48Mbps300 mA+/-100mA 54Mbps0.90 A+/-100mA54Mbps300 mA+/-100mA Indoor (Antenna Dependent): Outdoor (Antenna Dependent): CARD INFORMATION ChipsetAtheros, 6th Generation, AR2316 Radio Operation IEEE 802.11b/g, 2.4GHz Interface32-bit mini-PCI Type IIIA Operation Voltage3.3VDC Antenna PortsSingle MMCX Temperature Range -40C to +80C (extended temp version up to +95C) SecurityWPA, WPA2, AES-CCM & TKIP Encryption, 802.1x, 64/128/152bit WEP Data Rates6Mbps, 9Mbps, 12Mbps, 24Mbps, 36Mbps, 48Mbps. 54Mbps TX Channel Width Support5MHz / 10MHz / 20MHz / 40MHz RoHS ComplianceYES REGULATORY INFORMATION Wireless Modular ApprovalsFCC Part 15.247, IC RS210 Linux MADWIFI, WindowsXP, Windows2000 802.11g OFDM CURRENT CONSUMPTION INFORMATION 40MHz (Turbo)20MHz10MHz5MHz RADIO OPERATING FREQUENCY 2412-2462 MHz (2312-2732 MHz*) TX SPECIFICATIONSRX SPECIFICATIONS TX CURRENT CONSUMPTIONRX CURRENT CONSUMPTION 802.11b 802.11b 802.11g OFDM DRIVER INFORMATION RANGE PERFORMANCE Operating System Support Copper / 4.3mm diameter Ground end to enclosure point tied to Earth GroundAttachment Procedure Terminal Material / Dimensions Over 50km 802.11b 802.11b 802.11g OFDM 802.11g OFDM ADJUSTABLE CHANNEL SIZE SUPPORT (Increase Channel Capacity or Increase Throughput) ESD/EMP CABLE SPECIFICATIONS 8 in length, 0.55mm diameter (26AWG) Cable Dimensions Up to 200meters MECHANICAL DIMENSIONS 495-499 Montague Expwy. Milpitas, CA 95035 San Jose, CA 95112 T (408)-942-3085 F (408)-351-4973 http://www.ubnt.com XTREMERange2

Ubiquiti Networks, Inc. 495-499 Montague Expwy Milpitas, CA 95035 2/6/07 Attn: MET laboratories 914 West Patapsco Ave. Baltimore, MD 21230 RE: CONFIDENTIALITY REQUEST FOR SuperRange4 (FCC ID: SWX-XR2) To Whom It May Concern: This letter serves as an official request for confidentiality under FCC Rule Section 0.459. We have requested that the schematics, block diagrams, Bill of Materials, tune-up procedure, and theory of operation required to be submitted with this application be withheld from public review. These documents contain proprietary information that would sacrafice our competitive advantage in the marketplace if made public. Please contact me if there is any information you may need. Sincerely, Robert J. Pera Senior RF Engineer

Ubiquiti Networks, Inc. 495-499 Montague Expwy. Milpitas, CA 95035 Attn:Reviewing Engineer MET Laboratories, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize MET Laboratories, Inc. to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). This agreement expires one year from the current date. Sincerely, 5/20/06 Robert J. Pera Senior RF Engineer

Ubiquiti Networks, Inc. 495-499 Montague Expwy Milpitas, CA 95035 September 27, 2007 Dear Application Examiner, Ubiquiti Networks FCC ID: SWX-XR2, would like to have your authorization as a modular approval specific to Mini PCI module. The requirements of Public Notice DA00-1407 have been met and shown on the following statements. 1. “The modular transmitter must have its own RF shielding.”: Device is equipped with metal shielding to cover RF section. Refer to external photos 2. “The modular transmitter must have buffered modulation/data inputs.”: All inputs to the modules are buffered through logic or microprocessor inputs. 3. “The modular transmitter must have its own power supply regulation.”: Internal 2.5V/3.3V power regulator. Refer to block diagram. 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C).”: The device is equipped with a unique antenna connector. Refer to external photos. 5. “The modular transmitter must be tested in a stand-alone configuration”: The device was tested in an adapter which exposed it outside that of a host laptop. 6. “The modular transmitter must be labeled with its own FCC ID number.”: There is one FCC ID submitter. A second FCC ID will be obtained by OEM customers for use in their hosts. 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.”: There are specific EEPROM settings inside the module that prohibit illegal usage. 8. “The modular transmitter must comply with any applicable RF exposure requirements.”: The module is NOT a portable device for laptops. Can only be used in mobile applications. Please contact me if you have any further questions. Regards, Robert J. Pera Senior RF Engineer

MET Laboratories, Inc. Safety Certification - EMI - Telecom Environmental Simulation 33439 WESTERN AVENUE ● UNION CITY, CALIFORNIA 94587 ● PHONE (510) 489-6300 ● FAX (510) 489-6372 October 2, 2007 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 RE: Ubiquiti Networks, FCC ID: SWX-XR2 To Whom It May Concern: MET Laboratories, Inc. would like to request the above FCC ID be placed in audit mode so that we may upload the Modular Approval Letter exhibit. The Modular Approval Letter was inadvertently left out of the original e-filing. The grants notes will be updated to reflect the Modular Approval. If you need any additional information, please let me know. Thank you, Jennifer Sanchez TCB Administrator MET Laboratories, Inc., Santa Clara, CA 408-213-2359 [email protected] [email protected]

FCCID: SWX-XR2IC: 6545A-XR2

Model Hyperliniktech HG2403RD-RSF Type: Dipole Gain: 3dBi

Model Hyperliniktech HG2403RD-RSF Type: Dipole Gain: 3dBi

Ubiquiti Networks XR2 MPE Calculation RF Exposure Requirements: §1.1307(b)(1) and §1.1307(b)(2): Systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess of the Commission’s guidelines. RF Radiation Exposure Limit: §1.1310: As specified in this section, the Maximum Permissible Exposure (MPE) Limit shall be used to evaluate the environmental impact of human exposure to radiofrequency (RF) radiation as specified in Sec. 1.1307(b), except in the case of portable devices which shall be evaluated according to the provisions of Sec. 2.1093 of this chapter. MPE Limit Calculation: EUT’s operating frequencies @ 2400-2483.5 MHz ; highest conducted power = 29.90dBm (peak) therefore, Limit for Uncontrolled exposure: 1 mW/cm 2 or 10 W/m 2 EUT maximum antenna gain = 3 dBi. Power Density Determination: S = PG / 4πR 2 or R = √(PG / 4πS) where, S = Power Density (1 mW/cm 2 ) P = Linear Power Input to antenna (977.2) G = Numerical Antenna Gain (2.0) R = Radius (20cm) S = (977.2*2.0/4π20 2 ) = (1954.2/5024) = 0.39 mW/cm 2 @ 20cm

MET Laboratories, Inc. Safety Certification - EMI - Telecom Environmental Simulation 33439 WESTERN AVENUE ! UNION CITY, CALIFORNIA 94587-3201 ! PHONE (510) 489-6300 ! FAX (510) 489-6372 The Nation’s First Licensed Nationally Recognized Testing Laboratory November 28, 2006 Ubiquiti Networks 495-499 Montague Expressway Milpitas, CA 95035 Dear Robert Pera, Enclosed is the Telecom test report for compliance testing of the Ubiquiti Networks, XR2 as tested to the requirements of Title 47 of the CFR, Ch. 1 (10-1-03 ed.), Part 15, Subpart B for a Class A Digital Device and Subpart C for Intentional Radiators. Thank you for using the services of MET Laboratories, Inc. If you have any questions regarding these results or if MET can be of further service to you, please feel free to contact me. Sincerely yours, MET LABORATORIES, INC. Jennifer Sanchez Documentation Department Reference: (\Ubiquiti Networks\EMCS21035B-FCC247) Certificates and reports shall not be reproduced except in full, without the written permission of MET Laboratories, Inc. While use of the National Voluntary Laboratory Accreditation Program (NVLAP) letters or the NVLAP Logo, the Standards Council of Canada Logo, or the Nationally Recognized Testing Laboratory (NRTL) Letters in this report reflects MET Accreditation under these programs, these letters, logo, or statements do not claim product endorsement by NVLAP or any Agency of the U.S. Government. This letter of transmittal is not a part of the attached report. MET Laboratories, Inc. Safety Certification - EMI - Telecom Environmental Simulation 33439 WESTERN AVENUE ! UNION CITY, CALIFORNIA 94587-3201 ! PHONE (510) 489-6300 ! FAX (510) 489-6372 MET Report: EMCS21035B-FCC247 © 2007, MET Laboratories, Inc. Page ii of vii Electromagnetic Compatibility Criteria Test Report For the Ubiquiti Networks Model XR2 Verified under The FCC Certification Rules Contained in Title 47 of the CFR, Part 15.247, Subpart C for Intentional Radiators MET Report: EMC21035B-FCC247 November 28, 2006 Prepared For: Ubiquiti Networks 495-499 Montague Expressway Milpitas, CA 95035 Prepared By: MET Laboratories, Inc. 4855 Patrick Henry Dr., Building 6 Santa Clara, CA 95054 Electromagnetic Compatibility Ubiquiti Networks Cover Page XR2 CFR Title 47, Part 15, Subpart B & C MET Report: EMCS21035B-FCC247 © 2007, MET Laboratories, Inc. Page iii of vii Electromagnetic Compatibility Criteria Test Report For the Ubiquiti Networks Model XR2 Tested Under The FCC Certification Rules Contained in Title 47 of the CFR, Part 15.247, Subpart C For Intentional Radiators Shawn McMillen, Billy Kwan, Project Engineer Jennifer Sanchez Electromagnetic Compatibility Lab Documentation Department Engineering Statement: The measurements shown in this report were made in accordance with the procedures indicated, and the emissions from this equipment were found to be within the limits applicable. I assume full responsibility for the accuracy and completeness of these measurements, and for the qualifications of all persons taking them. It is further stated that upon the basis of the measurements made, the equipment tested is capable of operation in accordance with the requirements of Part 15.247, of the FCC Rules under normal use and maintenance. Tony Permsombut, Manager Electromagnetic Compatibility Lab Electromagnetic Compatibility Ubiquiti Networks Report Status Sheet XR2 CFR Title 47, Part 15, Subpart B & C MET Report: EMCS21035B-FCC247 © 2007, MET Laboratories, Inc. Page iv of vii Report Status Sheet Revision Report Date Reason for Revision ∅ November 28, 2006 Initial Issue. Electromagnetic Compatibility Ubiquiti Networks Table of Contents XR2 CFR Title 47, Part 15, Subpart B & C MET Report: EMCS21035B-FCC247 © 2007, MET Laboratories, Inc. Page v of vii Table of Contents I. Executive Summary .................................................................................................................................................1 A. Purpose of Test ...................................................................................................................................................2 B. Executive Summary ............................................................................................................................................2 II. Equipment Configuration .......................................................................................................................................3 A. Overview.............................................................................................................................................................4 B. References...........................................................................................................................................................5 C. Test Site ..............................................................................................................................................................6 D. Description of Test Sample.................................................................................................................................6 E. Equipment Configuration....................................................................................................................................9 F. Support Equipment .............................................................................................................................................9 G. Ports and Cabling Information ..........................................................................................................................10 H. Mode of Operation............................................................................................................................................10 I. Method of Monitoring EUT Operation .............................................................................................................10 J. Modifications ......................................................…

Text truncated - open the document above for the full version.

Electromagnetic Compatibility Ubiquiti Networks Intentional Radiators XR2 CFR Title 47, Part 15, Subpart C MET Report: EMCS21035B-FCC247 © 2007, MET Laboratories, Inc. Page 38 of 63 Photograph 3. Test Equipment and setup for various Radiated Measurements