SZF3039GPS Bluetooth Receiver

GB735 GB735 Bluetooth GPS Receiver User manual Version 1.0 Tel: +886-2-8751-8598 Fax: +886-2-8797-3898 Email: [email protected] Web: http://www.cpss.com.tw No part of this User’s Manual may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying recording ,for any purpose other than the purchaser’s personal use, without the written permission of Compass Systems Cor p. Information in this User’s Manual is subject to change without notice. Compass S ystems Corp. reserves the right to change or improve or modify its products and to make changes to the content without obligation to notify any person or organization of such changes.©Copy right 2006 by Compass Systems Corp. All rights reserved. Printed in Taiwan Introduction i Introduction WARNINGS Some certain knowledge is required to be well known by the user for proper and safe use of Navibe Bluetooth GPS receiver. Please read this User’s Manual fi rst before operation. Because Navibe Bluetooth GPS receiver is an assistant device, it will N OT undertake any legal responsibility for any accident or damage caused by the user’s w rong operation and/or wrong judgement in navigating with Navibe. WARNINGS Some certain knowledge is required to be well known by the user for proper and safe use of Navibe Bluetooth GPS receiver. Please read this User’s Manual fi rst before operation. Because Navibe Bluetooth GPS receiver is an assistant device, it will N OT undertake any legal responsibility for any accident or damage caused by the user’s w rong operation and/or wrong judgement in navigating with Navibe. ii Introduction CAUTION The Global Positioning System(GPS) is a system of 24 satellites which c ircle the earth twice a day in a very precise orbit and transmit information to earth. T he Navibe unit must continuously find at least three of these satellites to calculate your position and your movement. This GPS system is operated by the government of the United States, which is s olely responsible for its accuracy and maintenance. Any changes of the system could affect the accuracy and performance of all GPS equipment. PLEASE CHARGE BATTERY FULLY BEFORE INITIAL USE. (When fully charged, red color-LED2 will automatica lly switch off.) CAUTION The Global Positioning System(GPS) is a system of 24 satellites which c ircle the earth twice a day in a very precise orbit and transmit information to earth. T he Navibe unit must continuously find at least three of these satellites to calculate your position and your movement. This GPS system is operated by the government of the United States, which is s olely responsible for its accuracy and maintenance. Any changes of the system could affect the accuracy and performance of all GPS equipment. PLEASE CHARGE BATTERY FULLY BEFORE INITIAL USE. PLEASE CHARGE BATTERY FULLY BEFORE INITIAL USE. (When fully charged, red co (When fully charged, red co lor lor - - LED2 will automatically switch off.) LED2 will automatically switch off.) iii Introduction Thank you for choosing Thank you for choosing Navibe Bluetooth GPS Receiver Navibe Bluetooth GPS Receiver ! ! Take it now Take it now ------ ------ it can be your best friend! it can be your best friend! Application Conditions:Navibe is designed for outdoors navigation in the temperature range of -20 ° C~ 70 ° C. Introduction section gives you a general overview of Navibe features. Reference section tells how to operate the unit correctly and how to connect this unit to your pocket PC step-by-step.If you find something missing or damaged with the reference to the standard pac kage, please contact the local dealer or retailer. iv Introduction Chapter I Introduction Section 1 Announcement i Section 2 Warnings ii Section 3 Caution iii Section 4 Welcome to Navibe iv Section 5 Table of Contents v Chapter II Reference Section 1 Hardware Description 1 Section 2 State Table of LED 2 Section 3 Packet PC Setup 5-8 v Low Power (red) & Battery Charging (Yellow) –LED2 Reference 1 Hardware Description Hardware Description Hardware Description DC Charging Jack Battery Cover GPS External Antenna Connector (MMCX type) Power Switch GPS (Green –LED1) Bluetooth (Blue –LED3) Reference 2 State Table of LED State Table of LED Blue ON Blue ON Blue Flash Blue Flash ing ing Yellow OFF Yellow OFF Yellow ON Yellow ON Red ON Red ON Green Flashing Green Flashing Green ON Green ON Connected Low Power Charging Battery Charged Bluetooth LED LED 3 (Right) Pairing Low Power & Battery Charging LED LED 2 (Middle) Signal Acquiring Position Locked GPS Status LED 1 (Left) Reference Usage Usage 3 The second LED (LED 2) indicator will turn RED when battery power becomes low. Connect the receiver to a power source to recharge the battery. When the battery is being charging, LED2 will turn YELLOW. When fully charged, the YELLOW indicator will switch OFF. Please charge the battery fully be fore first use. To turn off the receiver, push the power switch to “OFF” position. All of the LED indicators will turn off.To turn on the receiver, first, make sure that the battery is loaded securel y then push the power switch to “ON” position. The green LED (LED 1) indicator will be flashing for searching GPS satellites. The blue LED (LED 3) indica tor will start flashing for searching Bluetooth device. Low Power & Charging Turn off Turn on Reference 4 The first LED (LED 1) green indicator will be flashing when searching satellites. When fixed, the LED green indicator (LED1) will become to steady on. The right LED (LED 3) blue indicator will flash for pairing Bluetooth sig nals. When connected, the LED blue indicator (LED3) will become to steady on. GPS Status Bluetooth Device Usage Usage Reference Pocket PC Setup 1. Tap “Bluetooth Manager” from Start Menu 2.Tap New > Connect 5 Pocket PC Setup Pocket PC Setup Note Note : In : In “ “ Bluetooth: Device Pairing Bluetooth: Device Pairing ” ” window you will required to enter window you will required to enter the Passkey number th…

Text truncated - open the document above for the full version.

5 5 4 4 3 3 2 2 1 1 D D C C B B A A AUTH.ENG.CHK.Page : 1 of 2 REV : 2.0 DRN. EB712ASiRF3 EngineBoard BLOCK Battery& POWER BlueTooth 2.402~ BlueTooth Antenna 2.480GHz Module Antenna GPS 1575.42 MHz MMCX GB735 SiRF3 X'TAL:26MHz TCXO:24.5535MHzX'TAL:32.768KHz 5 5 4 4 3 3 2 2 1 1 D D C C B B A A 2 of 2 ENG.Page :AUTH.DRN.CHK. REV : 2.0 EXT BATTER POWER Circuit Schematic LED4 LED3 LED2LED1 Bluetooth LED BlueTooth Circuit GPS Circuit GPS LED Install R17,the EB712 boot fromBOOTROM For Firmware updata use 1.45mm 6.58mm 2.55mm 1.45mm 2.55mm 6.58mm 2.55mm 1.2mm 1.2mm 1.45mm 1.2mm PCB Print Antenna ANTENNA Vin>3.2,Vout=VinVin<3.2,Vout=0 XC61CC3202MR Batt Low LED Vin>3.6V,Vout=VinVin<3.6V,Vout=0 Act low,Pin=0,LED ONVcc_BT< 3.6V GB735 SiRF3 BT_ANT GPS_STATE RESET BT_ANT TXA BT_ANT RXA GPS_STATE RXA TXA GPS_STATE B/S B/S USB_DM USB_DP USB_DM USB_DP VP VP +5V VP VP VBAT VCC_BT VCC_BT VCC_GPS VCC_GPS VCC_GPS VCC_GPS VIN +5V VIN VF +5V VF VBAT VP VCC_GPS VCC_GPS +5V VBAT VCC_GPS VCC_BT VCC_GPS VCC_GPS C20 NC R120R C140.1uF LED2M04-0603QGC R25NC R3 4.7K TP9 TXA 1 1 R26NC S1 S-LINE 1 1 TP10 VCC_GPS 1 1 B1 2.5A/120ohm/0603 R9100K C15 1.2pF R29 NC U2 APM2305N 1 3 2 C23 NC R14 330R Q2 IRLML6302 1 3 2 D1 XB01SB04A2BR C21NC C13NC C120.1uF C510uF LED3 M04-0603QGC R10 1K R5100K R11330R TP3 VIN 1 1 D3 BAT54C L5NC 1 2 C17 10nH B2 2.5A/120ohm/0603 C6 1uF C2210P C18 0.1uF L11.0nH R22NC Q3IRLML6302 1 3 2 R6 0.3R 0805 C2 1uF U5 XC61CC3602MR 3 1 2 VIN VOUT VSS TP5 VCC_BT 1 1 R16 0R C1 1uF USB1 MINI-USB-B 1 2 3 4 6 7 8 9 5 +5V D- D+ NC ShieldShieldShieldShield GND LED1M04-0603QRC 1 2 R17NC R28 NC ANT2 GPS ANTENNA U4 3 1 2 VIN VOUT VSS R15 0R C10 0.1uF L2NC R30 NC R10R C24 NC U3RT9501B 1 2 3 4 8 7 6 5 VCC TS STAT VSS BATSNSFB/CECC U6 EB712A 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 VUSBUSB_DMUSB_DPP20NCGNDGNDRF_GNDNCRF_GNDANT_INRF_GND VCC3.3V VBAT_IN NCNCNC GND NC RESET RXD2 RXD TXD GPS LED R21330R R2 1K Q4NPN 2SC4081 L382nH TP7 B/S 1 1 M1M2.5K4.1 1 1 D2 XB01SB04A2BR R4100K C16NC R13100K R18 NC C1110uF L4 NC 1 2 J1 MMCX-S25-006E0 1 2 3 1 2 3 U8 CSR BC2 MODULE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 GNDVDD_PAGND_PAAIO<0>AIO<1>RESETSPI_MISOSPI_CSBSPI_CLKSPI_MOSIUART_CTSUART_TXUART_RTSUART_RX1V83V3GND PCM_OUT PCM_SYNC PCM_IN PCM_CLK USB_DP USB_DN PIO<7>PIO<6>PIO<5>PIO<4>PIO<3>PIO<2>PIO<1>PIO<0> GND RF GND Shield Shield Shield Shield CON2 BTP-03DF4G 1 2 3 4 5 6 7 + R - ---- LED4 M04-0603QBC R27 0R U1 XC6401EE38MRN 1 2 3 6 5 4 ENIVinEN2 VOUT1 VSS VOUT2 R7 500K C19 0.1uF C70.1uF TP8 RXA 1 1 SW1 1270 SHN TP1VCC_GPS 1 1 R20NC M2M2.5K4.1 1 1 R31 NC R23NC TP6 GND 1 1 ANT1 RF ANT5220110AOT 1 2 INOUT

Report No.: 06CL102-RFUSP06V01 Page : 1 of 10 Version:1.0 Attachment 2 : EUT Detailed Photographs (1) EUT Photo (2) EUT Photo

COMPASS SYSTEMS CORP. FCC ID.: SZF3039 6F,NO.413, Sec.2, Ti-Ding Blvd., Neihu Dist., Taipei, 114 Taiwan . Tel : 886-2-8751-8598#515 FCC ID Label The FCC ID will be placed on the equipment as shown in the photograph below.

Report No.: 06CL102-RFUSP06V01 Page : 2 of 10 Version:1.0 (3) EUT Photo (4) EUT Photo Report No.: 06CL102-RFUSP06V01 Page : 3 of 10 Version:1.0 (5) EUT Photo (6) EUT Photo Report No.: 06CL102-RFUSP06V01 Page : 4 of 10 Version:1.0 (7) EUT Photo (8) EUT Photo Report No.: 06CL102-RFUSP06V01 Page : 5 of 10 Version:1.0 (9) EUT Photo (10) EUT Photo Report No.: 06CL102-RFUSP06V01 Page : 6 of 10 Version:1.0 (11) EUT Photo (12) EUT Photo Report No.: 06CL102-RFUSP06V01 Page : 7 of 10 Version:1.0 (13) EUT Photo (14) EUT Photo Report No.: 06CL102-RFUSP06V01 Page : 8 of 10 Version:1.0 (15) EUT Photo (16) EUT Photo Report No.: 06CL102-RFUSP06V01 Page : 9 of 10 Version:1.0 (17) EUT Photo (18) EUT Photo Report No.: 06CL102-RFUSP06V01 Page : 10 of 10 Version:1.0 (19) EUT Photo

Report No. 06CL102-RFUSP06V01 Page: 7 of 44 Version:1.0 1.2. Operational Description The EUT is a GPS Bluetooth Receiver with a built-in 2.4GHz transceiver. The signals are modulated by frequency hopping spread spectrum. The number of channels is 79 in 2402-2480MHz. The EUT provides wireless technology that revolutionizes personal connectivity. It is the solution for the seamless integration of Bluetooth technology into personal computer enabling short-range wireless connections between desktop/laptop computers, Bluetooth-enabled peripherals, and portable handheld devices. Test Mode Mode 1: Transmitter

SCHEMATIC1 : BC04 Extra Flash , 2007/1/25 1 / 1 A bo c om T i m C o nf i d en t i a l 55 44 33 22 11 D D C C B B A A BC04 Extra Flash V2.0 BTM401 Custom 11 Tuesday, January 02, 2007 TitleSize Document Number Rev Date: Sheet of DNDP SPI_CLKSPI_MISOSPI_MOSISPI_CSBUART_TXUART_RTSUART_CTSUART_RXPCM_OUTPCM_CLKPCM_SYNCPCM_IN RF_OUT Reset PIO0PIO1PIO2PIO3PIO4PIO5PIO6PIO7PIO8PIO9PIO10PIO11 PIO7 UART_RX Reset SPI_CSB SPI_MISO PCM_CLKPCM_SYNC PIO11 PIO5 SPI_CLK PIO8 PIO9 PIO6 UART_TX UART_RTS PIO10 UART_CTS PCM_INPCM_OUTPIO1PIO3DPRF_OUTPIO2PIO4 SPI_MOSI DNPIO1 1.8V 3.3V 1.8V 3.3V 3.3V 3.3V 3.3V 3.3V1.8V R4 0 C1610NF R3 10K C104.7UF R11 0 U3BTM401 123456789 1011121314151617 1920212223242528293031273326323418 35 36 37 38 GNDNCGNDNCNCRESETSPI_MISOSPI_CSBSPI_CLKSPI_MOSIUART_CTSUART_TXUART_RTSUART_RX1.8V3.3VGND PCM_SYNC PCM_IN PCM_CLK DP DN PIO7PIO6PIO3PIO2PIO1 LED_OUT PIO4 RF_OUT PIO5 GNDGND PCM_OUT PIO8 PIO9 PIO10 PIO11 C8NC C1310NF C18 18PF R2 10K Y1 26.000MHz 1 3 2 4 C48.2p C38.2p C9NC U4 DBF81F106 123 456 7 8 Unbalanced portDCNC Balanced Port1 GND1 Balance Port2 GND2 GND3 U1 BC04 Extra Flash A2 E9C11D10K11K10 E11 D11 A1 E10J3H3C9C10J11H9B1B2F11E3F3G3G9H10 D9C2 D3 H2 D1 E2 F10 E1 D2 F1F2 C8 J1 J10 C1 H1 K2 J9 J5 L10 K8 C3 B3 L3 K1 K6 J8 A10 L9 J4 J6 A3 K4 L1 L2 K3 J2 J7 K7 K9 L8 L5 K5 L6 B10 L4 L11 H11F9G11G10 A11 G1G2 B11 L7 A4 C4 B5 A6 C6 B7 A8 A9 B4 A5 C5 B6 A7 C7 B8 B9 VDD_PIO PIO[5] SPI_CSB SPI_MOSI USB_DN USB_DP VDD_CORE VDD_PADS VSS_DIG1 PIO[4]PIO[3]PIO[2] SPI_MISO SPI_CLK UART_CTSUART_RTS PIO[0]PIO[1]PIO[6]PIO[9] PIO[10]PIO[11] UART_TX UART_RX VSS_DIG2NC1 PIO[8] VREG_EN RF_INVSS_RADIO2 PIO[7] RF_BVSS_RADIO1RF_AVSS_RADIO3TEST_EN VDD_LO VSS_DIG3 VDD_RADIO VSS_LO AIO[2] A[13] A[7] A[15] A[10] REB CSB VDD_ANA AIO[0] A[5] A[11] A[16] A[12] A[2] WEB A[0] A[1] XTAL_IN XTAL_OUT VSS_ANA AIO[1] A[8] A[17] A[14] A[9] A[3] A[4] A[6] RESETB VREG_IN VDD_USB PCM_IN PCM_OUT PCM_SYNC PCM_CLK VDD_MEM NC2NC3NC4 A[18] D[0] D[1] D[2] D[3] D[4] D[5] D[6] D[7] D[8] D[9] D[10] D[11] D[12] D[13] D[14] D[15] C1 15PF R5 22 C1147NF C1710NF U2 SST39VF800A A3 H1H6 G4 E1 D1 C1 A1 B1 D2 C2 A2 B5 A5 C5 D5 B6 A6 C6 D6 E6 B2 C3 E2 H2 E3 H3 H4 E4 H5 E5 F2 G2 F3 G3 F4 G5 F5 G6 G1 A4 F1 B3 B4 C4 D3 D4 F6 NC1 VSS1VSS2 VCC A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 OE WE CE NC2 NC3 NC4 NC5 NC6 NC7 L1 22NH R1 2.2 C2 4.7UF R6 22 C615PF C5 22PF

55 44 33 22 11 D D C C B B A A GSC3f GSC3fGSC3fGSC3f Baseband Baseband Baseband Baseband + Flash + Flash+ Flash+ Flash BOOTSEL Optional (1PPS) ON_OFF must be Low during boot up and operation Page :AUTH.CHK.ENG. EB712 Baseband Schematic DRN. REV : 3.0 EB712 SiRF Star III EB 2 of 3 SSIII Freq SelTCK TDI 0 0 16.369M 0 1 24.5535M 24 PINCONNECTOR BATTERY CIRCUIT RESERT CIRCUIT POWER CIRCUIT nMWE NC RXB GPIO9 RESETVCCIN FREQ XFER BOOTSEL JTDOJTMS TXA RF_GND ON_OFF PWRCTLRF_GNDRF_GND ANT IN JTCK nICERST nRESET GPIO0 TIMERSYNC RXA nICERST DATA7DATA11 ADR5 DATA13DATA9DATA5 ADR4ADR1nMOEADR18ADR3 DATA1 ADR12ADR7ADR11nCS0ADR19ADR15 DATA2 ADR9 DATA12 ADR13ADR14 DATA6DATA8 ADR16 DATA14 nMWEADR2ADR17 DATA10 ADR20ADR6 DATA3DATA15 ADR10ADR8 DATA4DATA0 JTMS RXA nCS1 FREQ XFER ON_OFF PWRCTLnCS2 nICERST DATA0CS_FDATA3 RTC_IN nCS0 GPIO0JTCK DATA1 GPIO1 TIMERSYNC nSRESET nICERST JTDOSCLK TXA JTDI RXB JTDI DATA2 GPIO9 nSRESET nICERST nRESET JTCKJTMSJTDIJTDOECLK ED[0] CLKACQSIGN_MAGSPI_CLK TXA TimeMarkPWRCTL BATTERY1 RFINPUT ECLK ED[0]TimeMark SPI_DIRTC_OUT RXA JTDOJTDIJTCKJTMS TXA nSRESET ON_OFF ON_OFF PWRCTL nICERST nRESET nICERST nSRESET GPIO0 GPIO15 RXA SPI_DOSPI_enableGPIO15GPIO0 BATTERY BATTERY1 BATTERY VCC_GSP VDD_RTC VCC_GSP VCC_GSP VCC_GSP VDD_RTC VDDk VDDk VCC_GSP VCC VCC_GSP VCC_GSP VCCRF VCC VCC_GSP VCC_GSP VCC_GSP C24 1uF/16V C361000P C3712pF C30 0.01uF 2 1 BT1SiRF 12 TP14 TEST POINT 1 1 R340 OHM 1 2 U6S817B15AMCCWH 132 54 GND OUT IN NC1NC2 TP15 TEST POINT 1 1 R3310K C32 2.2uF U8 AME8500AEETAF23 3 1 2 VDD G Reset C38 1000P P5 PAD-TP1 1 R17 100K R8 NC 1 2 R4 R0201 2 1 + C2322uF/10v R2910K C1 1uF/16v P6 PAD-TP1 1 R18 10K R19100K R30 10K 12 C272.2uF C35 0.01uF R160 ohm 1 2 R1210K R10R0402 1 2 TP3 TestPointTOP U4BIC_GSC3e E1 A10 C6J6J7B5B1 D5 F1 B2 C1J8C8 D6 A9 D7 B6 A2 D3 A3 C7 B8A8 B9 C9D8 J1 D1 G1 B7 B3 E8 D9 A7M1 E3 C2 E2 E5 E6 F9F8 E9 A6 K1 F3 C3 F2 G3G8 H9 G9 A5 L1 D2 G2 B4 B10 C4 H7 G7 H8 N1 H2 C5 F5 D10E7 G5G6 C10 J10 H3 K3J4J5 H5 F6 F10 H4 E10 J2 A4 J3 G4 D4 E4 F4 F7 G10H10 K2 L2 L3 A1 H1J9H6 CS3 / GPIO15 / Timersync VDDPLL_O TIMEMARK / GPIO9 SI / GPIO5 SK / GPIO7 EIT0 / GPIO10 RFPWRUP / GPIO8 GND_BB CS1 / GPIO13 / nCTS MWE CS2 / GPIO14 / nRTS SO / GPIO6 RES GND_BB EA0EA2EA4 ODO / GPIO1 CS0CS_FRXB RES SCLK EA1EA3EA5 JTDI MOE ED0TXB VDD_FLash EA7EA6 ECLK JTDO ED8ED1ED9 GND_BB GND_BB EA19EA18EA8TXA JTRST ED2ED10ED3ED11EA11EA10EA9RXA JTMS ED4ED12 VDD_RTC VDDK VDD_REG EA14EA13EA12 JTCK ED5 VDD_PLL GND_BB TMODE WAKEUP EA16EA15 VDDK SRESETED13 AGCPWM / GPIO2 CLKACQ SIGN_MAG EA17 GND_BB RIN ED6 ROUT ED7 GPIO0 ED15ED14 VDD_BB VDD_BB VDD_BB VDD_REG ON_OFF nRESET VDD_BB VDD_BB VDD_BB GND_BB SS1 / GPIO4 /MAG SS0 / GPIO3 PLL_FILTER TP2 TestPointTOP D1 MA27784 12 R21 100K U5 AM29LV400B-BGA F6 B4 A4 F1 G1 D4C3 B2E6 D6C6 A6 B6 D5C5 A5 B5 A2 C2D2 B1 A1 C1D1 E1 G4 H1 H6 G6F5G5F4G3F3G2F2E5H5E4H4H3E3H2E2A3 nBYTEnRESnWEnCEnOEA19A18A17A16A15A14A13A12A11A10A9A8A7A6A5A4A3A2A1A0 VCC VSS[1] VSS[2] D15D14D13D12D11D10 D9D8D7D6D5D4D3D2D1D0 RY/nBSY C34 0.01uF 12 C9470pF/50V U1 XC6401EE25MRN 123 654 ENIVinEN2 VOUT1 VSS VOUT2 C2470pF/50V R9 4.7K TP13TEST POINT 1 1 R5 R0402 2 1 TP10 TestPointTOP R2810K C3 1uF/16V R32NC TP12TEST POINT 1 1 C33 0.01uF R20 10K P3 PAD-TP1 1 C29 2.2uF R2 4.7K 1 2 R6100R R7 R0402 2 1 CONN_SOCKET_12x2/SM STAMP1 123456789 101112 CONN_SOCKET_12x2/SMSTAMP2 123456789101112 P4 PAD-TP1 1 TP8 TestPointTOP ADR20nMWE DATA5DATA6DATA8DATA9DATA10DATA11DATA12DATA13DATA14 ADR14ADR6 DATA15 ADR15ADR7ADR16ADR19ADR8ADR17ADR9ADR1ADR18ADR10ADR2ADR11nMOEADR3ADR12ADR4ADR13ADR5 DATA4 DATA7 55 44 33 22 11 D D C C B B A A GSC3f GSC3fGSC3fGSC3f RF RFRFRF Section SectionSectionSection Maximize thermalisolation ofTCXO (REF_FREQ) EB712 RF Schematic ENG.AUTH.CHK. 3 of 3 Page : EB712 SiRF Star III EB REV : 3.0 DRN. RF CIRCUIT CLOCK CIRCUIT RF OPTION 2FOR MODULEPAD OUTPUTUSE Y1 12 34 X1 1 2 3 4 24.5535MHZ ROUT RFIN SPI_CLKRTC_OUT_ASPI_DISPI_DATA RIN SPI_ENCLKACQSIGN_MAGXTALIN XTALIN RTC_OUT XTALIN nRESET RFINPUT SIGN_MAGSPI_DISPI_CLKSPI_DOSPI_enableCLKACQ VCCRF VCCRF VCCRF_DIG VCCRF_DIG VCCRF VCCRF VDD_RTC VCCRF In Out Gnd Vcc Gnd GS U2 bga428 6 2 1 3 5 4 R1 R0402 2 1 L16.8nH R3180K C4 100pF IN OUT GND GND FIL2 856308 1 2 3 4 C16 100pF 1 2 C15 100pF 1 2 P1 PAD-TP1 1 L2NC 12 C120.01uF C50.01uF C26 NC U4AIC_GSC3e K5K4K6K7K8 L4 L5 L6 L7 L8 L9 M3 M4 M5 M6 M7 M8 M9 M10 N3 N4 N5N6N7 N8 N9 N10 P2P3 P5P6P7P4 P9 P10P1 M2 N2 P8 L10K9K10 SIGN_MAG CLKACQ SPI_DO SPI_CLK SPI_DI GND_RF GND_RF GND_RF GND_RF GND_RF GND_RF VCC_RF VCC_RF VCC_RF VCC_RF VCC_RF VCC_RF VCC_RF VCC_RF GND_RF GND_RF GND_RFGND_RFGND_RF GND_RF GND_RF GND_RF XTAL_IN XTAL_OUT GND_RFRFINGND_RFTPIF VCC_RTC RTC_XI GRFRST VCC_RF GND_RF VCC_1O_EXT RTC_XO SPI_CEB RTC_OUT C61000pF_X7R C17 NC 12 C7330pF P2 PAD-TP1 1 C10 1nH 1 2 C13 1000pF_X7R C22 0.01uF C181000pF_X7R C14 1000pF_X7R TP1 TestPointTOP C1918pF Y1 32.768_Khz 1 4 32 C25 100pF 1 2 L35.6nH 1 2 C110.01uF C2033pF C822pF U7 24.5535_MHz_.5ppm_TX2142 3 1 24 O/P N/C GND Vcc

Report No. 06CL102-RFUSP06V01 Page: 1 of 44 Version:1.0 Test Report Product Name GPS Bluetooth Receiver Model No. GBx3x FCC ID. SZF3039 Applicant COMPASS SYSTEMS CORP. Address 6F., No. 413, Sec. 2, Ti-Ding Blvd., Neihu Dist., Taipei, 114 Taiwan Date of Receipt Dec. 18, 2006 Issued Date Jan. 23, 2007 Report No. 06CL102-RFUSP06V01 The Test Results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. This report must not be used to claim product endorsement by NVLAP any agency of the U.S. Government Report No. 06CL102-RFUSP06V01 Page: 2 of 44 Version:1.0 Test Report Certification Issued Date: Jan. 23, 2007 Report No.: 06CL102-RFUSP06V01 Product Name GPS Bluetooth Receiver Applicant COMPASS SYSTEMS CORP. Address 6F., No. 413, Sec. 2, Ti-Ding Blvd., Neihu Dist., Taipei, 114 Taiwan Manufacturer COMPASS SYSTEMS CORP. Model No. GBx3x FCC ID. SZF3039 Rated Voltage AC 120V/60Hz Working Voltage Battery 3.7V, or AC 120V/60Hz, or DC 12V Applicable Standard FCC CFR Title 47 Part 15 Subpart C: 2005 ANSI C63.4: 2003 CISPR 22: 2005 Test Result Complied The Test Results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. This report must not be used to claim product endorsement by NVLAP any agency of the U.S. Government Documented By : ( Genie Chang ) Tested By : ( Tim Sung ) Approved By : ( George Chen ) 0914 Report No. 06CL102-RFUSP06V01 Page: 3 of 44 Version:1.0 TABLE OF CONTENTS Description Page 1. GENERAL INFORMATION ...............................................................................................................5 1.1. EUT Description......................................................................................................................................5 1.2. Operational Description...........................................................................................................................6 1.3. Test System Details .................................................................................................................................7 1.4. Configuration of Test System ..................................................................................................................7 1.5. EUT Exercise Software ...........................................................................................................................8 1.6. Test Facility .............................................................................................................................................9 2. CONDUCTED EMISSION ................................................................................................................10 2.1. Test Equipment ......................................................................................................................................10 2.2. Test Setup ..............................................................................................................................................10 2.3. Limits.....................................................................................................................................................11 2.4. Test Procedure .......................................................................................................................................11 2.5. Uncertainty ............................................................................................................................................11 2.6. Test Result of Conducted Emission .......................................................................................................12 3. PEAK POWER OUTPUT ..................................................................................................................14 3.1. Test Equipment ......................................................................................................................................14 3.2. Test Setup ..............................................................................................................................................14 3.3. Limit.. ....................................................................................................................................................14 3.4. Uncertainty ............................................................................................................................................14 3.5. Test Result of Peak Power Output .........................................................................................................15 4. RADIATED EMISSION .....................................................................................................................16 4.1. Test Equipment ......................................................................................................................................16 4.2. Test Setup ..............................................................................................................................................17 4.3. Limits.....................................................................................................................................................17 4.4. Test Procedure .......................................................................................................................................18 4.5. Uncertainty ............................................................................................................................................18 4.6. Test Result of Radiated Emission ..........................................................................................................19 5. BAND EDGE .......................................................................................................................................23 5.1. Test Equipment ....................................................................................…

Text truncated - open the document above for the full version.

Report No.: 06CL102-RFUSP06V01 Page : 1 of 3 Version:1.0 Attachment 1: EUT Test Setup Photographs Front View of Conducted Test Back View of Conducted Test Report No.: 06CL102-RFUSP06V01 Page : 2 of 3 Version:1.0 Front View of Radiated Test Back View of Radiated Test Report No.: 06CL102-RFUSP06V01 Page : 3 of 3 Version:1.0 Front View of Radiated Test (Horn) Back View of Radiated Test (Horn)