TA8AKRC161741-2Remote Radio Unit which supports WCDMA, LTE, NB-IoT, and NR

Ericsson Internal 1 (1) Prepared (also subject responsible if other) EHUAYAN No. TA8AKRC161741-2 Approved Checked Date Rev Reference Hua Yang 2020-12-17 A Federal Communications Commission Authorization & Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21046 Attention: Equipment Authorization Branch Subject: Certification for FCC ID: TA8AKRC161741-2 To Whom It May Concern: Ericsson AB requests a Grant of Certification (Type Acceptance) for the above mentioned FCC Identifier. The radio operates in the Broadband Radio Service band as per 47 CFR Part 27. This radio (Radio 4402 B7) is designed for used in WCDMA, LTE and NR cellular telephone system. This FDD radio operates in Band 7. The transmitter is from 2620MHz to 2690MHz and the receiver is from 2500MHz to 2570MHz. It supports radio ac cess technology SR WCDMA, SR LTE, SR NR and MR WCDMA + LTE+ NB-IoT (in-band, NB-IoT standalone, guard-band)+NR. It supports channel bandwidths of 5 MHz for WCDMA, 200KHz for NB-IoT standalone, 1.4, 3, 5, 10, 15 and 20 MHz for LTE and 5, 10, 15 and 20 MHz for NR. The radio supports modulation types of QPSK, 16 QAM and 64 QAM for WCDMA; QPSK for NB-IoT; QPSK, 16QAM, 64QAM and 256 QAM for LTE&NR. The radio s upports spectrum consisting of two or more sub-blocks separated by sub-block gap(s), NCS (None- Contiguous Spectrum). The radio unit supports carrier aggregation. The radio has the ability to be used in a RBS system configured for 3GPP MIMO/Spatial multiplexing and beam- forming technologies for LTE. This radio will in normal mode operates at a maximum power of 5W per port, the radio has 4 TX/RX ports. The Exhibit 8 user manuals submitted with this application is generic and may cover multiple produc ts. This application is only valid for the model specified in the Exhibit 12 circuit description. Ericsson AB requests confidentiality under CFR 0.459 according to attached letter. We further certify that the applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to section 5301 of the Anti-Drug abuse Act of 1988, 21 U.S.C. Section 862. If additional information is needed, please contact me on the below listed number. Hua Yang Staff Engineer, Regulatory Programs Ericsson AB Isafjordsgatan 10 Kista, SE-164 80 Stockholm Sweden Telephone No.: +86 10 8476 7133 e-mail: [email protected]

Ericsson Internal 1 (2) Prepared (also subject responsible if other) EHUAYAN No. TA8AKRC161741-2 / 287AB-AS1617412 Approved Checked Date Rev Reference Hua Yang 2020-12-18 A Federal Communications Commission Authorization & Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21046, USA Attention: Equipment Authorization Branch Innovation, Science and Economic Development Canada Certification and Engineering Bureau 3701 Carling Avenue, Bldg.94 P.O. Box 11490, Station “H” Ottawa, Ontario K2H 8S2 Canada Subject: Request for Confidentiality FCC ID: TA8AKRC161741-2 IC: 287AB-AS1617412 To Whom It May Concern: We, Ericsson AB, hereby request that the Exhibits/Items listed below be withheld from public inspection in accordance with Sections 0.457 and 0.459 of the Commission’s Rules for FCC and in accordance to RSP- 100 Section 9.4 for ISED. This due to the following reasons: This Base Stations (BS) are designed strictly based on the technical specifications of the international project 3GPP (the 3rd Generation Partnership Project). The competition in this field is very intense and a less advanced solution/design could get an unf air advantage by accessing the information as listed below from common domain. As we believe that we have implemented grou ndbreaking solutions and designs into our recent BS/Radio Unit (RU) / Remote Radio Unit (RRU) / Radio DoT (RD) compared to the previous BS/RU/RRU/RD, the listed Exhibits/Items need to be protected from disclosure to our competitors in the industry. As the FCC/ISED records have in-depth information and a very wide distrib ution, we believe that you can understand our concerns. We are strong in our belief that all vendors in the indu stry need to c ompete by their own merits. We regard these Exhibits/Items to be our intellectual property and therefore as confidential information. There are adva nced technical and design solutions/information in the Exhibits/Items, as mentioned above, that we regard as Erics son proprietary, with actual and potential patents pending. The information can be advantageous to our competitors as well as sources seeking ways to hack past the built in security functionality. These solutions or information thereof are not accessible even for our customers or partners unless non-disclosure agreements for particular item(s) have been signed. Confidential product information can be found in, but not necessarily limited to, internal photo s of the BS, RU, RRU and RD, block diagrams, schematics diagrams , and parts lists as well as certain documents, such as the user’s manuals. Those documents can onl y be accessible by the customers who purchase our BS/RU/RRU/RD and accept the conditions and therefore are provided with unique information access tools. EXHIBIT 4 Block Diagrams EXHIBIT 9 Internal Photos EXHIBIT 5 Schematics EXHIBIT 10 Parts List EXHIBIT 8 Manuals EXHIBIT 12 Technical Circuit Description Ericsson Internal 2 (2) Prepared (also subject responsible if other) EHUAYAN No. TA8AKRC161741-2 / 287AB-AS1617412 Approved Checked Date Rev Reference Hua Yang 2020-12-18 A We, Ericsson AB hereby authorize BABT and ISED Canada to publish all or part of the following information on the IC website: Certification number; Company number; previous certification number (if applicable); Company name; Company contact information (name, address, email, fax, phone); Manufacturer (name, contact person address, email, fax phone): Representative in Canada; Model name and/or number as it appears on the product; Specification or standard code and issue number; Type of equipment (equipment category); Test Lab name, address, ID#, OATS filing reference number; Test Lab report number and date; List of accessories with which the equipment was tested; List of operational features; Frequency Range; Emission Designator(s); Nature of signal(s); Type of information being transmitted; Details about the signal(s); Nature of multiplexing; Bandwidth(s); Type of modulation(s); Field strength measured in microvolt per meter @ 3 meters if the antenna is integral to the device or conducted RF Power if the antenna is detachable; and Gain of antenna(s) the device was certified with. Hua Yang Staf f Engineer, Regulatory Programs Ericsson AB FCC Registration Number (FRN): 0013476155 Isafjordsgatan 10 Kista, SE-164 80 Stockholm Sweden Telephone No.: +86 10 8476 7133 e-mail: [email protected]

DatePage 15/12/20201(5) Exhibit 3 External photos FCC ID: TA8AKRC161741-2 I C ID: 287AB-AS1617412 Front side DatePage 15/12/20202(5) Exhibit 3 External photos FCC ID: TA8AKRC161741-2 IC ID: 287AB-AS1617412 Rear side DatePage 15/12/20203(5) Exhibit 3 External photos FCC ID: TA8AKRC161741-2 IC ID: 287AB-AS1617412 Left side Right side DatePage 15/12/20204(5) Exhibit 3 External photos FCC ID: TA8AKRC161741-2 IC ID: 287AB-AS1617412 Top side Top side DatePage 15/12/20205(5) Exhibit 3 External photos FCC ID: TA8AKRC161741-2 IC ID: 287AB-AS1617412 Bo ttom side

Exhibit 1 ID label and placement FCC ID: TA8AKRC161741-2 IC: 287AB-AS1617412 Da te Page 15 /12/2020 1(1) FCC ID: TA8AKRC161741-2 IC: 287AB-AS1617412 AS1617412

1 (11) GFTL-20:001695 Uen, Rev A, 2020-12-21 © Telefonaktiebolaget LM Ericsson AB. This report shall not be reproduced except in full, without written approval of the laboratory. EMF Test Report: Ericsson Radio 4402 B7 (FCC) Accred. no. 1761 Testing ISO/IEC 17025 Test report issued by an Accredited Testing Laboratory Document number: GFTL-20:001695 Uen Rev A Date of report: 2020-12-21 Testing laboratory: Ericsson EMF Research Laboratory Ericsson AB SE-164 80 Stockholm Sweden Company/Client: Ge Li CBC - Ericsson (China) Communications Co. Ltd. Bldg 2, No.1366 Tianfu Avenue 610041 Chengdu China Tests performed by: Paramananda Joshi Dates of tests: 2020-12-18 (Rev A) Manufacturer and market name(s) of device: Ericsson Radio 4402 B7 Testing has been performed in accordance with: FCC OET Bulletin 65 IEC 62232:2017 Test results: RF exposure compliance boundaries (exclusion zones) related to the limits in FCC 47 CFR 1.1310 to be included in the Customer Product Information (CPI) for Ericsson Radio 4402 B7. Additional information: Signature: Test Engineer __________________ Paramananda Joshi Senior Researcher [email protected] Tel: +46725074006 Laboratory and Quality Manager _______________________________ Christer Törnevik Senior Expert – EMF and Health [email protected] Tel: +46705863148 2 (11) GFTL-20:001695 Uen, Rev A, 2020-12-21 Summary of EMF Test Report 1 Equipment under test (EUT) Product name Radio 4402 B7 Product number KRC 161 741/2 Supported bands, Tx frequency range (MHz) and standards B7 (2600) 2620 – 2690 WCDMA, LTE, NB-IoT, NR Duplexing technology FDD Exposure environment General public/uncontrolled, Workers/controlled Results RF exposure compliance boundaries, outside of which the exposure is below the general public (GP) and workers (W) exposure limits, are listed below. Dimensions of the box-shaped compliance boundary for general public (GP) and workers (W) exposure for Radio 4402 applicable in the markets employing the FCC exposure limits for maximum output power with output power tolerance of 0.6 dB included. Mode and output power for Radio 4402 Dimensions of the box-shaped compliance boundary (m) Distance in front of EUT Width Height Distance behind EUT Band Standard 2 Single/Dual Radio version Maximum nominal output power from the radio IEC 62232 Installation class GP W GP W GP W GP W B7 W/L/I/N Single 4 × 5 W E+ 2.1 1.0 1.8 0.8 1.3 0.7 0.2 0.2 B7 W/L/I/N Dual 4 × 5 W + 4 × 5 W E+ 2.9 1.3 2.5 1.2 2.1 1.2 0.2 0.2 For the power levels specified in the table with tolerances added, and the upward rounding of compliance boundary dimensions to the nearest decimeter, the specified results are conservative. 1 This page contains a summary of the test results. The full report provides a complete description of all test details and results. 2 The standards are abbreviated in this report according to: W for WCDMA, L for LTE, I for NB-IoT, and N for NR. 3 (11) GFTL-20:001695 Uen, Rev A, 2020-12-21 1 General information The test results presented in this report define compliance boundaries for Radio 4402 B7. Outside of these compliance boundaries, the radio frequency (RF) exposure levels are below the limits specified by the Federal Communications Commission (FCC) [1]. The tests were performed by calculations in accordance with the Ericsson RF exposure calculation procedure for base stations [2], which is in conformity with the FCC OET Bulletin 65 [3] and IEC 62232:2017 [4]. It should be noted that the test results presented in this test report are valid for the frequency range specified in Table 1, for the antenna properties specified in Table 2, and for the power level and the power tolerance specified in Table 3. These data as well as the applied antenna pattern files were supplied by the client and may affect the validity of the results. Proposed EMF health and safety information for inclusion in the Customer Product Information (CPI) is provided in Appendices A, B and C. 2 Equipment under test Table 1 and Table 2 below summarize the technical data for the equipment under test (EUT) and the properties of the integrated antenna. Table 3 lists the nominal peak output power from the radio unit (total peak power from all antenna branches) and the total power delivered to the antenna for the specified configuration. The total power delivered to the antenna includes output power tolerance. The EUT was tested for both Single Radio and Dual Radio versions shown in Appendix D. In the Single Radio version, each radio unit has its own power supply unit, while in the Dual Radio version one power supply unit can support two radios. The EUT related data in Tables 1-3 were supplied by the client. Table 1 Technical data for the EUT. Product name and product number Radio 4402 B7 KRC 161 741/2 Supported bands, Tx frequency range (MHz), and standards B7 (2600) 2620 – 2690 WCDMA, LTE, NB-IoT, NR Antenna KRE 105 283/1 Duplexing technology FDD Dimensions, 푯×푾×푫 (mm) 213.5 × 200 × 147 (Single radio including power supply and antenna unit) 449 × 200 × 152 (Dual radio including power supply and antenna unit) Exposure environment General public, Workers IEC 62232:2017 installation class 3 [4] E+ (Single Radio) E+ (Dual Radio) Table 2 Properties of the antenna. Product number KRE 105 283/1 Type Internal antenna, directional, 4 Tx (2 columns, ± 45º polarization) Tested band and frequency range (MHz) 2620 – 2690 Gain (dBi) 4 10.8 Electrical downtilt (degrees) -8 Number of dual-polarized elements and inter element separation distance (mm) for each column 2, 2 70, 70 Dimensions, 푯×푾×푫 (mm) 200 × 200 × 25 3 The stated IEC 62232 installation class was determined based on the total EIRP without power tolerance included. The total EIRP was obtained using the antenna patterns provided by the client. 4 Maximum gain per antenna port obtained using the antenna patterns provided by the antenna manufacturer. 4 (11) GFTL-20:001695 Uen, Rev A, 2020-12-21 Table 3 EUT configurations with nominal outpu…

Text truncated - open the document above for the full version.

No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. TEST REPORT No.I20Z61972-WMD01 for Ericsson AB Radio 4402 B7 KRC 161 741/2 Remote Radio Unit FCC ID: TA8AKRC161741-2 ISED: 287AB-AS1617412 In accordance with FCC CFR 47 Part 27 and ISED RSS-199: Issue 3 Issued Date: 2020-12-22 Note: The test results in this test report relate only to the devices specified in this report. This report shall not be reproduced except in full without the written approval of CTTL. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the U.S.Government. Test Laboratory: CTTL, Telecommunication Technology Labs, CAICT No. 52, Huayuan North Road, Haidian District, Beijing, P. R. China 100191. Tel:+86(0)10-62304633-2512, Fax:+86(0)10-62304633-2504 Email: [email protected], website: www.caict.ac.cn No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. Page 2 of 257 REPORT HISTORY Report Number Revision Description Issue Date I20Z61972-WMD01 Rev.0 1 st edition 2020-12-22 Note: the latest revision of the test report supersedes all previous version. No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. Page 3 of 257 CONTENTS 1. TEST LABORATORY ......................................................................................................................... 4 1.1. INTRODUCTION & ACCREDITATION ...................................................................................... 4 1.2. TESTING LOCATION .................................................................................................................... 4 1.3. PROJECT DATE .............................................................................................................................. 5 1.4. SIGNATURE ..................................................................................................................................... 5 2. CLIENT INFORMATION ................................................................................................................... 6 2.1. APPLICANT INFORMATION ....................................................................................................... 6 2.2. MANUFACTURER INFORMATION ............................................................................................ 6 3. EQUIPMENT UNDER TEST (EUT) .................................................................................................. 7 3.1. ABOUT EUT ..................................................................................................................................... 7 3.2. GENERAL DESCRIPTION ............................................................................................................ 8 3.3. CONFIGURATION DESCRIPTION ............................................................................................. 9 4. REFERENCE DOCUMENTS ........................................................................................................... 17 4.1. REFERENCE DOCUMENTS FOR TESTING ........................................................................... 17 5. TEST SETUP ...................................................................................................................................... 18 6. LABORATORY ENVIRONMENT ................................................................................................... 19 7. SUMMARY OF TEST RESULTS ..................................................................................................... 20 8. TEST EQUIPMENT UTILIZED ...................................................................................................... 21 9. MEASUREMENT UNCERTAINTY ................................................................................................ 21 ANNEX A: MEASUREMENT RESULTS ................................................................................................ 22 A.1 MAXIMUM OUTPUT POWER AND PEAK TO AVERAGE POWER RATIO - EIRP CALCULATION................ 22 A.2 OCCUPIED BANDWIDTH ...................................................................................................................... 75 A.3 SPURIOUS EMISSIONS AT BAND EDGE ................................................................................................113 A.4 CONDUCTED SPURIOUS EMISSION .................................................................................................... 171 A.5 RADIATED SPURIOUS EMISSION ........................................................................................................ 240 A.6 FREQUENCY STABILITY .................................................................................................................... 253 ANNEX B: ACCREDITATION CERTIFICATE ................................................................................... 257 No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. Page 4 of 257 1. Test Laboratory 1.1. Introduction & Accreditation Telecommunication Technology Labs, CAICT is an ISO/IEC 17025:2017 accredited test laboratory under NATIONAL VOLUNTARY LABORATORY ACCREDITATION PROGRAM (NVLAP) with lab code 600118-0, and is also an FCC accredited test laboratory (CN5017), and ISED accredited test laboratory (ISED#: 24849). The detail accreditation scope can be found on NVLAP website. 1.2. Testing Location Location 1: CTTL(huayuan North Road) Address: No. 52, Huayuan North Road, Haidian District, Beijing, P. R. China 100191 Location 4: CTTL(BDA) Address: No.18A, Kangding Street, Beijing Economic-Technology Development Area, Beijing, P. R. China 100176 No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. Page 5 of 257 1.3. Project date Testing Start Date: 2020-11-23 Testing End Date: 2020-12-14 1.4. Signature Dong Yuan (Prepared this test report) Zhou Yu (Reviewed this test report) Liu Baodian (Approved this test report) No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. Page 6 of 257 2. Client Information 2.1. Applicant Information Com…

Text truncated - open the document above for the full version.

No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. Page 84 of 257 Port D, QPSK/10.0MHz Channel Position B Port D, QPSK/10.0MHz Channel Position M Port D, QPSK/10.0MHz Channel Position T No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. Page 85 of 257 Port D, QPSK/15.0MHz Channel Position B Port D, QPSK/15.0MHz Channel Position M Port D, QPSK/15.0MHz Channel Position T No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. Page 86 of 257 Port D, QPSK/20.0MHz Channel Position B Port D, QPSK/20.0MHz Channel Position M Port D, QPSK/20.0MHz Channel Position T No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. Page 87 of 257 Port D, 16QAM/1.4MHz Channel Position M Port D, 16QAM/3.0MHz Channel Position M Port D, 16QAM/5.0MHz Channel Position M No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. Page 88 of 257 Port D, 16QAM/10.0MHz Channel Position M Port D, 16QAM/15.0MHz Channel Position M Port D, 16QAM/20.0MHz Channel Position M No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. Page 89 of 257 Port D, 64QAM/1.4MHz Channel Position M Port D, 64QAM/3.0MHz Channel Position M Port D, 64QAM/5.0MHz Channel Position M No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. Page 90 of 257 Port D, 64QAM/10.0MHz Channel Position M Port D, 64QAM/15.0MHz Channel Position M Port D, 64QAM/20.0MHz Channel Position M No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. Page 91 of 257 Port D, 256QAM/1.4MHz Channel Position M Port D, 256QAM/3.0MHz Channel Position M Port D, 256QAM/5.0MHz Channel Position M No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. Page 92 of 257 Port D, 256QAM/10.0MHz Channel Position M Port D, 256QAM/15.0MHz Channel Position M Port D, 256QAM/20.0MHz Channel Position M No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. Page 93 of 257 Configuration NB-IoT-InBand-1C -26dBc Occupied Bandwidth Modulation/ Bandwidth Occupied Bandwidth (MHz) Channel position B Channel position M Channel position T QPSK/ 5.0MHz 4.714 4.715 4.715 QPSK/ 10.0MHz 9.194 9.189 9.184 QPSK/ 15.0MHz 13.99 13.99 13.99 QPSK/ 20.0MHz 18.42 18.44 18.43 99% Occupied Bandwidth Modulation/ Bandwidth Occupied Bandwidth (MHz) Channel position B Channel position M Channel position T QPSK/ 5.0MHz 4.4793 4.4837 4.4874 QPSK/ 10.0MHz 8.9031 8.9022 8.8998 QPSK/ 15.0MHz 13.206 13.227 13.230 QPSK/ 20.0MHz 17.813 17.821 17.821 No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. Page 94 of 257 Port D, QPSK/5.0MHz Channel Position B Port D, QPSK/5.0MHz Channel Position M Port D, QPSK/5.0MHz Channel Position T No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. Page 95 of 257 Port D, QPSK/10.0MHz Channel Position B Port D, QPSK/10.0MHz Channel Position M Port D, QPSK/10.0MHz Channel Position T No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. Page 96 of 257 Port D, QPSK/15.0MHz Channel Position B Port D, QPSK/15.0MHz Channel Position M Port D, QPSK/15.0MHz Channel Position T No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. Page 97 of 257 Port D, QPSK/20.0MHz Channel Position B Port D, QPSK/20.0MHz Channel Position M Port D, QPSK/20.0MHz Channel Position T No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. Page 98 of 257 Configuration NB-IoT-GuardBand-1C -26dBc Occupied Bandwidth Modulation/ Bandwidth Occupied Bandwidth (MHz) Channel position B Channel position M Channel position T QPSK/ 10.0MHz 9.469 9.451 9.459 QPSK/ 15.0MHz 14.06 14.07 14.06 QPSK/ 20.0MHz 18.58 18.58 18.58 99% Occupied Bandwidth Modulation/ Bandwidth Occupied Bandwidth (MHz) Channel position B Channel position M Channel position T QPSK/ 10.0MHz 9.1099 9.1093 9.1081 QPSK/ 15.0MHz 13.641 13.632 13.629 QPSK/ 20.0MHz 18.077 18.094 18.091 Port D, QPSK/10.0MHz Channel Position B No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. Page 99 of 257 Port D, QPSK/10.0MHz Channel Position M Port D, QPSK/10.0MHz Channel Position T Port D, QPSK/15.0MHz Channel Position B No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. Page 100 of 257 Port D, QPSK/15.0MHz Channel Position M Port D, QPSK/15.0MHz Channel Position T Port D, QPSK/20.0MHz Channel Position B No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. Page 101 of 257 Port D, QPSK/20.0MHz Channel Position M Port D, QPSK/20.0MHz Channel Position T

No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. Page 102 of 257 Configuration NB-IoT-Standalone-1C -26dBc Occupied Bandwidth Modulation/ Bandwidth Occupied Bandwidth (KHz) Channel position B Channel position M Channel position T QPSK/ 250KHz 287.3 287.4 287.4 99% Occupied Bandwidth Modulation/ Bandwidth Occupied Bandwidth (KHz) Channel position B Channel position M Channel position T QPSK/ 250KHz 210.50 210.16 210.11 Port D, QPSK/250KHz Channel Position B Port D, QPSK/250KHz Channel Position M No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. Page 103 of 257 Port D, QPSK/250KHz Channel Position T Configuration NR-MIMO-1C -26dBc Occupied Bandwidth Modulation/ Bandwidth Occupied Bandwidth (MHz) Channel position B Channel position M Channel position T QPSK/ 5.0MHz 4.689 4.683 4.684 QPSK/ 10.0MHz 9.587 9.590 9.589 QPSK/ 15.0MHz 14.54 14.55 14.55 QPSK/ 20.0MHz 19.57 19.59 19.59 -26dBc Occupied Bandwidth Bandwidth Occupied Bandwidth (MHz) Modulation 16QAM/ Channel position M Modulation 64QAM/ Channel position M Modulation 256QAM/ Channel position M 5.0MHz 4.731 4.732 4.648 10.0MHz 9.528 9.562 9.577 15.0MHz 14.48 14.55 14.65 20.0MHz 19.45 19.40 19.47 No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. Page 104 of 257 99% Occupied Bandwidth Modulation/ Bandwidth Occupied Bandwidth (MHz) Channel position B Channel position M Channel position T QPSK/ 5.0MHz 4.4569 4.4605 4.4608 QPSK/ 10.0MHz 9.2876 9.2882 9.2838 QPSK/ 15.0MHz 14.037 14.047 14.036 QPSK/ 20.0MHz 18.742 18.772 18.745 99% Occupied Bandwidth Bandwidth Occupied Bandwidth (MHz) Modulation 16QAM/ Channel position M Modulation 64QAM/ Channel position M Modulation 256QAM/ Channel position M 5.0MHz 4.4193 4.4658 4.4399 10.0MHz 9.1944 9.1877 9.1987 15.0MHz 13.955 14.060 13.792 20.0MHz 19.005 19.013 18.613 Port D, QPSK/5.0MHz Channel Position B No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. Page 105 of 257 Port D, QPSK/5.0MHz Channel Position M Port D, QPSK/5.0MHz Channel Position T Port D, QPSK/10.0MHz Channel Position B No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. Page 106 of 257 Port D, QPSK/10.0MHz Channel Position M Port D, QPSK/10.0MHz Channel Position T Port D, QPSK/15.0MHz Channel Position B No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. Page 107 of 257 Port D, QPSK/15.0MHz Channel Position M Port D, QPSK/15.0MHz Channel Position T Port D, QPSK/20.0MHz Channel Position B No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. Page 108 of 257 Port D, QPSK/20.0MHz Channel Position M Port D, QPSK/20.0MHz Channel Position T Port D, 16QAM/5.0MHz Channel Position M No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. Page 109 of 257 Port D, 16QAM/10.0MHz Channel Position M Port D, 16QAM/15.0MHz Channel Position M Port D, 16QAM/20.0MHz Channel Position M No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. Page 110 of 257 Port D, 64QAM/5.0MHz Channel Position M Port D, 64QAM/10.0MHz Channel Position M Port D, 64QAM/15.0MHz Channel Position M No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. Page 111 of 257 Port D, 64QAM/20.0MHz Channel Position M Port D, 256QAM/5.0MHz Channel Position M Port D, 256QAM/10.0MHz Channel Position M No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. Page 112 of 257 Port D, 256QAM/15.0MHz Channel Position M Port D, 256QAM/20.0MHz Channel Position M No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. Page 113 of 257 A.3 Spurious Emissions at Band Edge A.3.1 Reference FCC CFR 47 Part 2, Clause 2.1051 FCC CFR 47 Part 27, Clause 27.53(m) RSS-199, Clause 4.5 A.3.2 Method of measurement The power of any emission outside of the authorized operating frequency ranges must be attenuated below the transmitting power (P) by a factor of at least 43 + 10log(P) dB. For MIMO mode configurations, the limit was adjusted with a correction of -6.02dB [10Log4] by using the Measure and Add 10Log(N) dB technique according to FCC KDB 662911 D01 Multiple Transmitter Output accounting for simultaneous transmission from antenna ports. Then the limit was adjusted to -19.02dBm. According to FCC rules, in the 1 MHz bands immediately outside and adjacent to the frequency block, a resolution bandwidth of at least one percent of the emission bandwidth of the fundamental emission of the transmitter may be employed and a RBW of 1MHz for measurements of emissions > 1MHz away from the band edges. The limit was adjusted with -13.01dB [10Log(50/1000)] to compensate for the reduce measurement bandwidth 50KHz for emission more than 1MHz away from the band edges. For MIMO mode, the limit of -32.03dBm was used for emission more than 1MHz away from the band edges. Spectrum analyzer detector was set as RMS. A.3.3 Measurement limit The power of any emission outside of the authorized operating frequency ranges must be attenuated below the transmitting power (P) by a factor of at least 43 + 10log(P) dB. No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. Page 114 of 257 A.3.4 Measurement result Configuration WCDMA-1C-BE, QPSK Band Edge Frequency Channel Bandwidth RBW (KHz) Limit (dBm) Channel Position B 5.0MHz 51 -19.02 Channel Position T 5.0MHz 51 -19.02 Port D, Channel Position B, QPSK No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. Page 115 of 257 Port D, Channel Position T, QPSK Configuration WCDMA-2C-BE, QPSK Band Edge Frequency Channel Bandwidth RBW (KHz) Limit (dBm) Channel Position B 5.0MHz 51 -19.02 Channel Position T 5.0MHz 51 -19.02 No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. Page 116 of 257 Port D, Channel Position B, QPSK Port D, Channel Position T, QPSK No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. Page 117 of 257 Configuration LTE-MIMO-1C, QPSK Band Edge Frequency Channel Bandwidth RBW(KHz) Limit(dBm) Channel Position B 3.0MHz 30 -19.02 10.0 MHz 100 -19.02 Channel Position T 3.0MHz 30 -19.02 10.0 MHz 100 -19.02 Port D, Channel Position B, 3.0MHz No.I20Z61972-WMD01 ©Copyright. All righ…

Text truncated - open the document above for the full version.

No.I20Z61972-WMD01 ©Copyright. All rights reserved by CTTL. Page 122 of 257 Port D, Channel Position B, 10.0MHz Port D, Channel Position T, 10.0MHz No.I20Z61972-WMD…

Text truncated - open the document above for the full version.