TA8AKRY901328-1WCDMA/LTE Radio Equipment

Exhibit 2 Authorization Letter

EXHIBIT 13 1 (1) Prepared (also subject responsible if other) No. EBJOUTE TA8AKRY901328-1 Approved Checked Date Rev Reference EAB/FJB/KA 2015-01-19 A Federal Communications Commission Authorization & Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21046 Attention: Equipment Authorization Branch SP Technical Research Institute of Sweden Brinellgatan 4 Box 857 S-501 15 Borås Sweden Jan 19, 2015 Subject: Certification for FCC ID: TA8AKRY901328-1 To Whom It May Concern: Ericsson AB requests a Grant of Certification (Type Acceptance) for the above mentioned FCC Identifier. This Radio Unit (Radio Dot – RD 2242) is designed for use in WCDMA and LTE cellular telephone system. The transmitter will operate from 1930 MHz to 1990 MHz. The receiver circuit supports 1850 MHz to 1910 MHz. It supports channel bandwidths of 5, 10, 15 and 20 MHz for LTE and 5 MHz for WCDMA. Radio Unit (RU) supports modulation type QPSK, 16QAM and 64QAM for WCDMA and LTE. Radio Unit operates in the Broadband PCS services as per 47 CFR Part 24 subpart E. It meets the requirements of Third Generation Partnership Project (3GPP) for operation in WCDMA and LTE cellular system. Radio Unit supports spectrum consisting of two or more sub-blocks separated by sub-block gap(s), NCS (None- Contiguous Spectrum). Radio Unit has the ability to be used in a RBS system configured for 3GPP MIMO/Spatial multiplexing and beam- forming technologies for WCDMA and LTE. Radio Unit will in normal mode operate at a nominal power out of 50 mW per port at the output connectors (2 connectors with up to 50 mW in each connector connected to build in antennas). This Radio Unit (Radio Dot – RD 2242) will always require a license for transmission. The Exhibit 8 user manuals submitted with this application is generic and may cover multiple products. This application is only valid for the model specified in the Exhibit 12 circuit description. Ericsson AB requests confidentiality under CFR 0.459 according to attached letter. We further certify that the applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to section 5301 of the Anti-Drug abuse Act of 1988, 21 U.S.C. Section 862. If additional information is needed, please contact me on the below listed number . Björn Utermöhl Staff Engineer, Regulatory Programs Ericsson AB Isafjordsgatan 10 SE-164 80 Stockholm, Sweden Telephone No.: +46107178646 e-mail: [email protected]

EXHIBIT 13 1 (2) Prepared (also subject responsible if other) No. EBJOUTE TA8AKRY901328-1 287AB-AS9013281 Approved Checked Date Rev Reference EAB/FJB/KA 2015-01-14 A Federal Communications Commission Authorization & Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21046, USA Attention: Equipment Authorization Branch SP Technical Research Institute of Sweden Brinellgatan 4 Box 857 S-501 15 Borås Sweden Industry Canada Certification and Engineering Bureau 3701 Carling Avenue, Bldg.94 P.O. Box 11490, Station “H” Ottawa, Ontario K2H 8S2 Canada Subject: Request for Confidentiality To whom it may concern: We, Ericsson AB, hereby request that the Exhibits/Items listed below be withheld from public inspection in accordance with sections 0.457 and 0.459 of the Commission’s rules and RSP-100 section 6.4 for IC. This due to the following reasons: Ericsson Base Stations (BS) are designed strictly based on the technical specifications of the international project 3GPP (the 3rd Generation Partnership Project). The competition in this field is very intense and a less advanced solution/design could get an unfair advantage by accessing the information as listed below from common domain. As we believe that we have implemented groundbreaking solutions and designs into our recent BS/Radio Unit (RU)/Radio Dot (RD) compared to the previous BS/RU/RD, the listed Exhibits/Items need to be protected from disclosure to our competitors in the industry. As the FCC and IC records have in-depth information and a very wide distribution, we believe that you can understand our concerns. We are strong in our belief that all vendors in the industry need to compete by their own merits. We regard these Exhibits/Items to be our intellectual property and therefore as confidential information. There are advanced technical and design solutions/information in the Exhibits/Items, as mentioned above, that we regard as Ericsson proprietary, with actual and potential patents pending. The information can be advantageous to our competitors as well as sources seeking ways to hack past the built in security functionality. These solutions or information thereof are not accessible even for our customers or partners unless non-disclosure agreements for particular item(s) have been signed. Confidential product information can be found in, but not necessarily limited to, internal photos of the BS RU and RD, block diagrams, schematics diagrams, and parts lists as well as certain documents, such as the user’s manuals. Those documents can only be accessible by the customers who purchase out BS/RU/RD and accept the conditions and therefore are provided with unique information access tools. EXHIBIT 13 2 (2) Prepared (also subject responsible if other) No. EBJOUTE TA8AKRY901328-1 287AB-AS9013281 Approved Checked Date Rev Reference EAB/FJB/KA 2015-01-14 A EXHIBIT 4 Block Diagram EXHIBIT 9 Internal Photos EXHIBIT 5 Schematics EXHIBIT 10 Parts List EXHIBIT 8 Manuals EXHIBIT 12 Technical Circuit Description .......................................................... Björn Utermöhl Staff Engineer, Regulatory Programs Ericsson AB FCC Registration Number (FRN): 0013476155 Isafjordsgatan 10 SE-164 80 Stockholm Sweden Telephone No. +46 107178646 e-mail: [email protected]

Date Page Exhibit 3 External photos 2015-02-12 1(1) FCC ID: TA8AKRY901328-1 IC: 287AB-AS9013281 Top side Back side Side Label

Date Page Exhibit 1 ID label and placement 2015-02-06 1(1) FCC ID: TA8AKRY901328-1 IC: 287AB-AS9013281 Test object back side

1 (6) EAB-15:008158 Uen, Rev C, 2015-02-11 © Telefonaktiebolaget LM Ericsson AB. This report shall not be reproduced except in full, without written approval of the laboratory. Rapport utfärdad av ackrediterat provningslaboratorium Test report issued by an Accredited Testing Laboratory EMF Test Report: Ericsson RD 2242 B2 R2B Document number: Rev C Date of report: 2015-02-11 Testing laboratory: Ericsson EMF Research Laboratory Ericsson AB SE-164 80 Stockholm Sweden Company/Client: FJB/RICPeter Wedin Ericsson AB SE-164 80 Stockholm Sweden Tests performed by: Elif Degirmenci Dates of tests: 2015-01-30 Manufacturer and market name(s) of device: Ericsson RD 2242 B2 Testing has been performed in accordance with: FCC CFR title 47, part 1.1310, FCC OET Bulletin 65, FCC KDB447498 D01, Industry Canada RSS 102 Test results: The tested device complies with the requirements in respect of all parameters subject to the test. Additional information: Testing was conducted for mobile exposure conditions Signature: Test Engineer _________________________ Elif Degirmenci Experienced Researcher [email protected] Tel: +46 10714 65 01 Quality Manager ________________________________ Björn Thors Senior Specialist - RF Exposure Assessment [email protected] Tel: +46 10717 1824 2 (6) EAB-15:008158 Uen, Rev C, 2015-02-11 1Summary of EMF Test Report 1 Frequency Band [MHz]B2 ModesLTE, WCDMA Supported  Covered by report  Exposure environmentGeneral public 1.1Results RF exposure assessment results for general public (uncontrolled) exposure applicable in USA and Canada[1] - [4] are given in the table below. The equipment under test (EUT) conforms to the requirements of the relevant standards when the combined exposure ratio is less than one. RF exposure assessment results for general public (uncontrolled) exposure as obtained for the RDS together with an assumed output power tolerance of 2.7 dB and a transmission loss of0.5 dB usingprocedures applicable for the US and Canadian markets [3], [4]. 3GPP bandStandard Nominal output power from the radio Test position Test separation distance Exposure ratio Result B2 (1900)L, W2 x 0.05 W Direction of maximum gain 20 cm0.1 PASSED 1 This page contains a summary of the test results. The full report provides a complete description of all test details and results. 3 (6) EAB-15:008158 Uen, Rev C, 2015-02-11 2General information The test results reported in this document have been obtained by simple calculations according to plane-wave equivalent conditions [4]. The purpose of the tests was to verify that the EUT is in compliance with the appropriate RF exposure standards, recommendations and limits [1] - [4] . 3Equipment under test Table 1 summarizes the technical data for the EUT. Photographs of the EUT are presentedin Appendix A. Table 1 Technical data for the EUT. Product name RD 2242 B2 Product tested KRY901 328/1 Dimensions, Thicknessx Diameter(mm) 50 x 109 Configurations(s) covered by this report LTE WCDMA1900 (B2) Antenna(s) Internalantennas Product numberMaximum gain (dBi) KRE1012191/23 dBi Transmitter frequency range (MHz) LTE WCDMA1900(B2): 1930-1990 In Table 2 nominal output power levels are given. Table 2 Nominal output power levels. 4EMF exposure assessments FCC procedures [4] specify exposure assessment methods to verify compliance with EMF exposure limits [1] of mobile devices. A minimum test separation distance of at least 20 cm is required between the device and nearby persons to apply mobile device exposure limits. The test separation distance for which the equipment is shown to comply with the exposure limits must be clearly provided in the operating and installation instructions. 4.1Field strength calculations The maximum gain, , of the two antennas used is 3 dBi (2.0), see Table 1. Assuming correlated transmit signals, the directional gain, , may be taken as 6 dBi according to [5]. This is most likely a very conservative assumption given the used transmission modes and antenna topology. The total effective radiated power for the omni-directional antennas is 0.4 W. As a consequence, the categorical exclusion provision of FCC CFR title 47, § 2.1091(c) applies [6] and the minimum test separation distance may be estimated by simple calculations according to plane-wave equivalent conditions [4]. The exposure ratio, , may be conservatively estimated as 2 Nominal output powerper port. 3 Conservative measure of the total maximum possible output power level delivered to the antennas including losses and tolerances. Band / Mode Nominal output power 2 (dBm) Tolerance, upper limit (dB) Transmission loss (dB) Maximum output power 3 (dBm) LTE B2 (1900), 2x50mW172.70.522.2 4 (6) EAB-15:008158 Uen, Rev C, 2015-02-11 = = 4 , where P : Total conducted power for the cellular bands (22.2 dBm), G: Directional gain (6 dBi), : Separation distancefrom antenna, : Power density exposure limit of10 W/m 2 . Setting = 0.166 W, =3.98, = 0.20 m and = 10 W/m 2 gives the result for a 20 cm test separation distance in Table 3. Table 3 RF exposure assessment results for general public (uncontrolled) exposure as obtained for the RDS using procedures applicable for the US and Canadian markets [3], [4]. 3GPP bandStandard Nominal output power from the radio Test position 4 Test separation distance 5 Exposure ratio Result B2 (1900)L, W2 x 0.05 W Direction of maximum gain 20 cm0.1 PASSED The exposure ratio is well below one. Hence, the RF EMF exposure is below the relevant exposure limits [1] for the 20 cm test separation distance. 5Conclusion The results in Section 4 show that the plane-wave equivalent power density, estimated according to the requirements of FCC [4] and Industry Canada [3], is below the relevant MPE limits [1] at a separation distance of 20 cm between the equipment and any nearby person. Consequently, the EUT is in compliance with the appropriate RF exposure standards and recommendations. 6Refere…

Text truncated - open the document above for the full version.

R a ( S Po SP Bo SE Sw T P P S S S F 2 2 2 2 2 2 2 N a S E P J R Iss Th Co Jö El +4 jo Radio me and IC:28 (9 appendice SP Technical ostal address P ox 857 E-501 15 BORÅS weden Test object Product name Product num Summary See appendix Standard FCC CFR 4 2.1046 / RSS 2.1046 / RSS 2.1049 / RSS 2.1051 / RSS 2.1051 / RSS 2.1053 / RSS 2.1055 / RSS Note: Above according to SP Technic Electronics - Performed by Jörgen Wassh REPOR sued by an FCC listed he test site complies w ntact person örgen Wassh lectronics 46 10 516 57 06 orgen.wassholm easuremen 87AB-AS9 s) Research Ins Office location Västeråsen Brinellgatan SE-504 62 B e: RD 2242 B mber: KRY 90 x 1 for gener 7 part 2 and S-133 6.4 S-133 6.4 S-Gen 6.6 S-133 6.5 S-133 6.5 S-133 6.5 S-133 6.3 RSS-133 ite ANSI proce cal Researc - EMC holm RT d Laboratory Reg. no. with RSS-Gen, IC file n holm 6 [email protected] nts on RD 9013281 stitute of Swe n Phon 4 BORÅS +46 +46 info @ B2 01 328/1 al informati o d 24 / IC RS RF power o RF power o Occupied b Band edge Spurious em Field streng Frequency s ems are given dures referen ch Institute 93866. no. 3482A-1 Date 2015 Eric s Nikla PDU Torsh 164 8 D 2242 B2 eden ne / Fax / E-mail 10 516 50 00 33 13 55 02 @sp.se on and appen SS-133 Issue output condu output radiate andwidth mission at an gth of spuriou stability n as cross-re nced by FCC of Sweden Examin And Refere 5-02-13 4P0 sson AB as Warnström U HW hamnsgatan 83 Stockholm 2 with FC Laboratories are Conformity Asse This report may n written approval ndix 9 for ex 6 ucted ed ntenna termin us radiation eference only C and covere n ned by ders Nordlöf ence 08534-01-F2 m 21 m C ID TA8 accredited by the S ssment (SWEDAC not be reproduced of the issuing labor ternal photos Comp Y Y Y Y nals Y Y Y y. Measureme d by SP’s ac Page 24 1 (2) 8AKRY9 Swedish Board for C) under the terms o other than in full, e ratory. s. pliant Ap Yes Yes Yes Yes Yes Yes Yes ments were pe ccreditation. ISO/I ) 01328-1 Accreditation and of Swedish legislati except with the prio ppendix 2 3 4 5 6 7 8 erformed 1002 EC 17025 on. r S T D O T P R R O B S F F E R SP Technical Table of co Description o Operation mo Test setups Purpose of te RF power ou RF power ou Occupied ban Band edge Spurious emi Field strength Frequency st External pho EPORT Research Ins ntents of the test ob ode during m est utput conduct utput radiated ndwidth ission at ante h of spurious tability tos stitute of Swe bject measurement ted d enna termina s radiation Date 2015 eden ts als Refere 5-02-13 4P0 ence 08534-01-F2 App Ap p Ap p Ap p Ap p Ap p Ap p Ap p Ap p Ap p Ap p Ap p Page 24 2 (2) pendix 1 pendix 1 pendix 1 pendix 1 pendix 2 pendix 3 pendix 4 pendix 5 pendix 6 pendix 7 pendix 8 pendix 9 ) S D R H T F A R R N p A A C M N R SP Technical Description Radio equipm Hardware rev Tested config Frequency ba Antenna port RF configura RF power tol Nominal outp per antenna p Antenna type Antenna gain Channel band Modulations Nominal sup EPORT Research Ins n of the test ment: vision state: guration: ands: ts: ation: lerance put power port: e: n: dwidths: : ply voltage: stitute of Swe t object RD Pro d FCC IC 2 IC M R2 B LTE TX: RX : 2 T X dire Sin g +2. 7 Sin g Mu Om n +3 d Sin g Mu QP S -48V Date 2015 eden 2242 B2 duct number C ID TA8AK 287AB-AS90 MODEL NO B E single RAT : 1930 – 199 : 1850 – 191 X/RX ports, ectional anten gle carrier, m 7/ -4.3dB gle carrier: ulti carrier: ni direction a dBi gel carrier: 5 ulti carrier: 5 SK, 16QAM VDC (associ Refere 5-02-13 4P0 Ap r: KRY 901 3 KRY901328- 013281 O: AS901328 T 0 MHz 0 MHz (internally c nna elements multi carrier,T 1x 17 dBm 2 x 14 dBm al antenna 5 MHz, 10 M MHz, 10 MH and 64QAM iated equipm ence 08534-01-F2 pendix 1 328/1 -1 1 onnected to s) TX-diversity m (1 x 50mW m (2 x 25mW MHz, 15 MHz Hz, 15 MHz M ment) Page 24 1 (10 integrated O y and MIMO W) W) z and 20 MH z and 20 MHz 0) Omni 2x2 Hz z S O M T 1 T d t c i M M C T c h R R R C T p T c A C R T R w u R SP Technical Operation m Measuremen TS 36.141. T 16QAM mod The settings b different mod tested to find configured fo if not otherw MIMO mode MIMO mode Cable config The cables, u clause 2.9 in has been used RDI Cable 20 RDI Cable 92 RDI Cable 20 Patch cable RDI cable Conducted m The conducte product numb The test obje cable. All TX param Complete me Radiated me The test obje RDI LAN ca were termina used. EPORT Research Ins mode during nts were perfo Test model E dulation and below were dulations, ch d the worst ca or maximum wise noted. e, single carr e, multi carri gurations be used during t Exhibit 12 – d: 0 m: total ca 2 m: total ca 00 m: total c Cat 6 Cat 6 measuremen ed measurem ber KRY 90 ect was moun meters were m easurements easurements ect was moun able represen ated into 50 o stitute of Swe g measureme ormed with t -TM1.1 repr test model E deemed repr hannel bandw ase setting. A m transmit pow ier, E-TM1.1 er, 2 carriers etween RD a tests, corresp – Technical C ble length 20 ble length 92 cable length 2 6a Schneider 6a Schneider nts ments were pe 1 328/1. nted in a fixtu measured at were made o s nted in a fixtu ting worst ca ohm. For RF Date 2015 eden ents the test objec resent QPSK E-TM3.1 repr resentative fo widths, numb All measurem wer. The sett 1 s, E-TM1.1 and IRU pond to minim Circuit Descr 0 m patch ca 2 m patch ca 200 m patch r Electric Act r Electric Act erformed on ure and pow port RF B w on RF B, lim ure and pow ase. In field s power outpu Refere 5-02-13 4P0 Ap ct transmittin K modulation resent 64QA or all traffic s ber of carriers ments were p tings below w mum and ma ription. The ables include ables include cables incl u tassi CL-MN tassi CL-MX RD 2242 B2 ered by the R with port RF A mited measure ered by the R strength of sp ut measurem ence 08534-01-F2 pendix 1 ng test model , test model E AM modulatio scenarios wh s and RF con erformed wi were used fo aximum leng following ca d. d. ded. NC6A XC6A 2 with RBS Main U A terminated ements on RF RBS Main U purios radiat ment the inter Page 24 2 (10 ls a…

Text truncated - open the document above for the full version.

R a ( S Po SP Bo SE Sw T P P S S S F 2 2 2 2 2 2 2 N a S E P J R Iss Th Co Jö El +4 Jö Radio me and IC:28 (9 appendice SP Technical ostal address P ox 857 E-501 15 BORÅS weden Test object Product name Product num Summary See appendix Standard FCC CFR 4 2.1046 / RSS 2.1046 / RSS 2.1049 / RSS 2.1051 / RSS 2.1051 / RSS 2.1053 / RSS 2.1055 / RSS Note: Above according to SP Technica Electronics – Performed by Jörgen Wassh REPOR sued by an FCC listed he test site complies w ntact person örgen Wassh lectronics 46 10 516 57 06 örgen.Wassholm easuremen 87AB-AS9 s) Research Ins Office location Västeråsen Brinellgatan SE-504 62 B e: RD 2242 B mber: KRC 90 x 1 for gener 47 Part 2 a S-133 6.4 S-133 6.4 S-Gen 6.6 S-133 6.5 S-133 6.5 S-133 6.5 S-133 6.3 RSS-133 ite ANSI proce al Research – EMC holm RT d Laboratory Reg. no9 with RSS-Gen, IC file n holm 6 [email protected] nts on RD 9013281 stitute of Swe n Phon 4 BORÅS +46 +46 info @ B2 01 328/1 al informati o and 24/ IC R RF power o RF power o Occupied b Band edge Spurious em Field streng Frequency s ems are given dures referen Institute of 93866 no. 3482A-1 Date 2015 Eric s Nikla PDU Torsh 164 8 D 2242 B2 eden ne / Fax / E-mail 10 516 50 00 33 13 55 02 @sp.se on and appen RSS-133 Is output condu output radiate andwidth mission at an gth of spuriou stability n as cross-re nced by FCC Sweden Examin And Refere 5-02-13 4P0 sson AB as Warnström U HW hamnsgatan 83 Stockholm 2 with FC Laboratories are Conformity Asse This report may n written approval . ndix 9 for ex ssue 6 ucted ed ntenna termin us radiation eference only C and covere ned by ders Nordlöf ence 08534-02-F2 m 21 m C ID TA8 accredited by the S ssment (SWEDAC not be reproduced of the issuing labor ternal photos Comp Y Y Y Y nals Y Y Y y. Measureme d by SP’s ac Page 24 1 (2) 8AKRY9 Swedish Board for C) under the terms o other than in full, e ratory. s. pliant Ap Yes Yes Yes Yes Yes Yes Yes ments were pe ccreditation. IS ) 01328-1 Accreditation and of Swedish legislati except with the prio ppendix 2 3 4 5 6 7 8 erformed 1002 SO/IEC 17025 on. r S T D O T P R R O B S F F E R SP Technical Table of co Description o Operation mo Test frequenc Purpose of te RF power ou RF power ou Occupied ban Band edge Spurious emi Field strength Frequency st External pho EPORT Research Ins ntents of the test ob odes during m cies and setu est utput conduct utput radiated ndwidth ission at ante h of spurious tability tos stitute of Swe bject measuremen ups ted d enna termina s radiation Date 2015 eden nts als Refere 5-02-10 4P0 ence 08534-02-F2 App Ap p Ap p Ap p Ap p Ap p Ap p Ap p Ap p Ap p Ap p Ap p Page 24 2 (2) pendix 1 pendix 1 pendix 1 pendix 1 pendix 2 pendix 3 pendix 4 pendix 5 pendix 6 pendix 7 pendix 8 pendix 9 ) S D R H T F A R R N p A A M C C N R SP Technical Description Radio equipm Hardware rev Tested config Frequency ra Antenna port RF configura RF power tol Nominal outp per antenna p Antenna type Antenna gain Modulations Channel band Channel spac Nominal sup EPORT Research Ins n of the test ment: vision state: guration: ange: ts: ation: lerance put power port: e: n: : dwidth: cing: ply voltage: stitute of Swe t object RD 224 Produc FCC I D IC 287A IC MO R2B WCD M TX: 19 RX: 1 8 2 TX/ R directio Single A +2.7/ - 4 Single 2 carri e 3 carrie 4 carrie Omni d +3 dBi QPSK, 5 MHz 5 MHz -48VD C Date 2015 eden 42 B2 ct number: K D TA8AKRY AB-AS9013 ODEL NO: A MA single RA 930 – 1990 M 850 – 1910 M RX ports, (int onal antenna Antenna (M u 4.3dB carrier: 1 er: 2 er: 3 er: 4 directional an 16QAM and z z C (associate d Refere 5-02-10 4P0 Ap RY 901 328/ Y901328-1 281 AS9013281 AT MHz MHz ternally conn elements) ultiple port), x 17 dBm (1 2 x 14 dBm (2 x 12.2 dBm 4 x 11 dBm (4 ntenna d 64QAM d equipment ence 08534-02-F2 pendix 1 /1 nected to inte MIMO 2x2 1 x 50mW) 2 x 25mW) m (3 x 16.7mW 4 x 12.5mW ) Page 24 1 (9) egrated Omn 2 W) W) ) ni S O T T 6 T d t c i S T C T c h R R R C T p T c A C R T c p m o R SP Technical Operation m Test models Test model 5 64QAM mod The settings b different mod tested to find configured fo if not otherw Single Anten TM1: 64 DPC Cable config The cables, u clause 2.9 in has been used RDI Cable 20 RDI Cable 92 RDI Cable 20 Patch cable RDI cable Conducted m The conducte product numb The test obje cable. All TX param Complete me Radiated me The test obje cable. In field power output measurement output measu EPORT Research Ins mode during as defined in 5 (TM5) inclu dulation. below were dulations, ch d the worst ca or maximum wise noted. nna (Multiple CH:s at 30 k gurations be used during t Exhibit 12 – d: 0 m: total ca 2 m: total ca 00 m: total c Cat 6 Cat 6 measuremen ed measurem ber KRY 90 ect was moun meters were m easurements easurements ect was moun d strength of t measureme ts the 200 m urements the stitute of Swe g measureme n 3GPP TS 2 udes the 16Q deemed repr hannel bandw ase setting. A m transmit pow e port) ksps (SF=128 etween RD a tests, corresp – Technical C ble length 20 ble length 92 cable length 2 6a Schneider 6a Schneider nts ments were pe 1 328/1. nted in a fixtu measured at were made o s nted in a fixtu f spurios radi ent the intern RDI cable w 200 m RDI Date 2015 eden ents 25.141. Test m QAM modula resentative fo widths, numb All measurem wer. The sett 8) and IRU pond to minim Circuit Descr 0 m patch ca 2 m patch ca 200 m patch r Electric Act r Electric Act erformed on ure and pow port RF B w on RF B, lim ure and pow iation both R nal antenna w was used to r cable was us Refere 5-02-10 4P0 Ap model 1 (TM ation and Tes or all traffic s ber of carriers ments were p tings below w mum and ma ription. The ables include ables include cables incl u tassi CL-MN tassi CL-MX RD 2242 B2 ered by the R with port RF A mited measure ered by the R RF ports were was used. For represent wor sed to repres ence 08534-02-F2 pendix 1 M1) represent st model 6 (T scenarios wh s and RF con erformed wi were used fo aximum leng following ca d. d. ded. NC6A XC6A 2 with RBS Main U A terminated ements on RF RBS…

Text truncated - open the document above for the full version.

R a ( S Po SP Bo SE Sw T P P S S S F 2 2 2 N a S E P J R Iss Th Co Jö El +4 jo Radio me and IC: 2 (5 appendice SP Technical ostal address P ox 857 E-501 15 BORÅS weden Test object Product name Product num Summary See appendix Standard FCC CFR 4 2.1046 / RSS 2.1051 / RSS 2.1053 / RSS Note: Above according to SP Technica Electronics – Performed by Jörgen Wassh REPOR sued by an FCC listed he test site complies w ontact person örgen Wassh lectronics 46 10 516 57 06 orgen.wassholm easuremen 87AB-AS s) Research Ins Office location Västeråsen Brinellgatan SE-504 62 B e: RD 2242 B mber: KRC 90 x 1 for gener 7 part 2 and S-133 6.4 S-133 6.5 S-133 6.5 RSS-133 ite ANSI proce al Research – EMC holm RT d Laboratory Reg. no9 with RSS-Gen, IC file n holm 6 [email protected] nts on RD S9013281 stitute of Swe n Phon 4 BORÅS +46 +46 info @ B2 01 328/1 al informati o d 24 / IC RS RF power o Spurious em Field streng ems are given dures referen Institute of 93866 no. 3482A-1 Date 2015 Eric s Nikla PDU Torsh 164 8 D 2242 B2 eden ne / Fax / E-mail 10 516 50 00 33 13 55 02 @sp.se on and appen SS-133 Issue output mission at an gth of spuriou n as cross-re nced by FCC Sweden Examin And Refere 5-02-13 4P0 sson AB as Warnström U HW hamnsgatan 83 Stockholm 2 with FC Laboratories are Conformity Asse This report may n written approval ndix 5 for ex 6 ntenna termin us radiation eference only C and covere ned by ders Nordlöf ence 08534-03-F2 m 21 m C ID: TA accredited by the S ssment (SWEDAC not be reproduced of the issuing labor ternal photos Comp Y nals Y Y y. Measureme d by SP’s ac Page 24 1 (2) A8AKRY9 Swedish Board for C) under the terms o other than in full, e ratory. s. pliant Ap Yes Yes Yes ments were pe ccreditation. IS ) 901328-1 Accreditation and of Swedish legislati except with the prio ppendix 2 3 4 erformed 1002 SO/IEC 17025 on. r S T D P O R S F E R SP Technical Table of co Description o Purpose of te Operation mo RF power ou Spurious emi Field strength External pho EPORT Research Ins ntents of the test ob est odes during m utput ission at ante h of spurious tos stitute of Swe bject measuremen enna termina s radiation Date 2015 eden nts als Refere 5-02-13 4P0 ence 08534-03-F2 App Ap p Ap p Ap p Ap p Ap p Ap p Page 24 2 (2) pendix 1 pendix 1 pendix 1 pendix 2 pendix 3 pendix 4 pendix 5 ) S D R H T O A R R N p A A L M C W M C C N R SP Technical Description Radio equipm Hardware rev Tested config Operating ba Antenna port RF configura RF power tol Nominal outp per antenna p Antenna type Antenna gain LTE Modulations Channel band WCDMA Modulations Channel band Channel spac Nominal sup EPORT Research Ins n of the test ment: vision state: guration: ands: ts: ation: lerance put power port: e: n: : dwidth: : dwidth: cing: ply voltage: stitute of Swe t object RD 224 Produc FCC I D IC 287A IC MO R2B MR W C TX: 19 RX: 1 8 MR W C 2 TX/ R directio LTE: T WCDM +2.7/ - 4 1-2 LT Total n Omni d +3 dBi QPSK , 5 MHz QPSK , 5 MHz 5 MHz -48VD C Date 2015 eden 42 B2 ct number: K D TA8AKRY AB-AS9013 ODEL NO: A CDMA + LT 930 – 1990 M 850 – 1910 M CDMA + LT RX ports, (int onal antenna TX diversity MA: Single A 4.3dB E + 1-4 WC number of car directional an , 16QAM an z, 10 MHz, 15 , 16QAM an z z C (associate d Refere 5-02-13 4P0 Ap RY 901 328/ Y901328-1 281 AS9013281 TE MHz MHz TE ternally conn elements) and MIMO 2 Antenna (Mu DMA (Total rriers 6 ntenna nd 64QAM 5 MHz and 2 nd 64QAM d equipment ence 08534-03-F2 pendix 1 /1 nected to inte 2x2 ultiple port) a l power 17 dB 20 MHz ) Page 24 1 (11 egrated Omn and MIMO 2 dBm, 50mW) 1) ni 2x2 ) S P T a O M W d ( L 3 r T d t c i W T L E C C T c h R R R R SP Technical Purpose of t The purpose applicable ite Operation m MR WCDMA WCDMA me defined in 3G (TM5) repres LTE measure 3GPP TS 36. represent 16Q The settings b different mod tested to find configured fo if not otherw WCDMA Sin TM1: 64 DPC LTE MIMO E-TM1.1 Channel band Cable config The cables, u clause 2.9 in has been used RDI Cable 20 RDI Cable 92 RDI Cable 20 Patch cable RDI cable EPORT Research Ins test of the tests i ems of FCC modes dur A + LTE easurements GPP TS 25.1 sent 16QAM ements were .141. Test m QAM modul below were dulations, ch d the worst ca or maximum wise noted. ngle Antenna CH:s at 30 k mode dwidth 5 MH gurations be used during t Exhibit 12 – d: 0 m: total ca 2 m: total ca 00 m: total c Cat 6 Cat 6 stitute of Swe is to verify co CFR 47, IC R ing measur were perform 41. Test mod M modulation performed w odel E-TM1 lation and tes deemed repr hannel bandw ase setting. A m transmit pow a (Multiple p ksps (SF=128 Hz etween RD a tests, corresp – Technical C ble length 20 ble length 92 cable length 2 6a Schneider 6a Schneider Date 2015 eden ompliance to RSS-133 and rements med with the del 1 (TM1) n and Test mo with the test .1 represent st model E-T resentative fo widths, numb All measurem wer. The sett port) 8) and IRU pond to minim Circuit Descr 0 m patch ca 2 m patch ca 200 m patch r Electric Act r Electric Act Refere 5-02-13 4P0 Ap o the perform d IC RSS-Ge e test object t represent QP odel 6 (TM6 object transm QPSK modu TM3.1 repres or all traffic s ber of carriers ments were p tings below w mum and ma ription. The ables include ables include cables incl u tassi CL-MN tassi CL-MX ence 08534-03-F2 pendix 1 mance charac en. transmitting PSK modula ) represent 6 mitting test m ulation, test m sent 64QAM scenarios wh s and RF con erformed wi were used fo aximum leng following ca d. d. ded. NC6A XC6A Page 24 2 (11 cteristics spec test models ation, Test m 64QAM mod models as def model E-TM M modulation hen settings w nfigurations ith the test ob or all measur gth, according able configur 1) cified in as odel 5 dulation. fined in M3.2 . with has been bject rements g to rations S C T p T c A C R T R w u R SP Technical Conducted m The conducte product numb The test obje cable. All TX param Complete me Radiated me The test obje RDI LAN ca were termina used. EPORT Research Ins measuremen ed …

Text truncated - open the document above for the full version.