TA8AKRY901332-1Remote Radio Unit supporting WCDMA LTE

Ericsson Internal EXHIBIT 13 COMMERCIAL IN CONFIDENCE 1 (1) Prepared (Subject resp) No. EDAVBOL DAB/EMC NDA 12.08.14 Approved (Document resp) Checked Date Rev Reference 2015-03-12 PA1 NDA Confidentiality Clause Confidentiality: Each party agrees that all confidential documents, work product and information (including all computer code, internal photographs of products, block diagrams, schematic diagrams, technical and/or user manuals, related materials, and the existence of this Agreement) received or otherwise obtained from the other party pursuant to this Agreement, whether before or after the Effective Date, will be, and will be deemed to have been, received in confidence and will be used only for the purpose of carrying out the obligations of, or as otherwise contemplated by, this Agreement. In addition, each party agrees that public access to all confidential equipment supplied will be restricted either by installation of the equipment in a restricted area or by physically securing the equipment by other means, including, but not limited to, using a key-lock that can only be opened by authorized personnel. Without the other party’s prior written consent, neither party may disclose any such information to any third party or grant access to the confidential equipment to any unauthorized person, and each party will disclose such information only to such of its officers, employees and agents that have a need to know such information for the purposes contemplated hereby. However, the provisions of this Section will not apply to any such information that (i) is or becomes generally available to the public without the fault or negligence of either party, (ii) is already in the possession of the receiving party without being subject to another confidentiality obligation, (iii) is or becomes available to the receiving party on a non-confidential basis from a source other than the disclosing party; provided that such source is not bound by a confidentiality obligation of the disclosing party, (iv) is required to be disclosed pursuant to an arbitration proceeding conducted in accordance with this Agreement, or (v) is required to be disclosed pursuant to a requirement of any governmental authority or any statute, rule or regulation; provided that the party required to disclose such information of the other party provide to the other party notice of such requirement of any such disclosure and cooperates with the other party to prevent or restrict any such disclosure to the extent allowed by applicable law.

EXHIBIT 13 1 (1) Prepared (also subject responsible if other) No. EDENLAL TA8AKRY901332-1 Approved Checked Date Rev Reference EDAVBOL 2015-03-10 A Federal Communications Commission Authorization & Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21046 Attention: Equipment Authorization Branch TUV SUD BABT Forsyth House Churchfield Road, Walton-on-Thames, Surrey KT12 2TD, UK April 02, 2015 Subject: Certification for FCC ID: TA8AKRY901332-1 To Whom It May Concern: Ericsson AB requests a Grant of Certification (Type Acceptance) for the above mentioned FCC Identifier. This Radio Unit (Radio Dot – RD 2242) is designed for use in LTE and WCDMA cellular telephone system. The transmitter will operate from 869 MHz to 894 MHz. The receiver circuit supports 824 MHz to 849 MHz. It supports channel bandwidths of 5 and 10 MHz for LTE and 4.2 to 5 MHz for WCDMA. The Radio Unit (RU) supports modulation types QPSK, 16QAM and 64QAM for LTE and WCDMA. The Radio Unit operates in the Cellular Radiotelephone Service as per 47 CFR Part 22. It meets the requirements of Third Generation Partnership Project (3GPP) for operation in LTE and WCDMA cellular systems. The Radio Unit supports spectrum consisting of two or more sub-blocks separated by sub-block gap(s), NCS (None- Contiguous Spectrum). The Radio Unit has the ability to be used in a RBS system configured for 3GPP MIMO/Spatial multiplexing and beam- forming technologies for LTE. The Radio Unit will in normal mode operate at a nominal power output of 50 mW per port at the output connectors (2 connectors with up to 50 mW in each connector connected to built-in antennas). This Radio Unit (Radio Dot – RD 2242) will always require a license for transmission. The Exhibit 8 user manuals submitted with this application are generic and may cover multiple products. This application is only valid for the model specified in the Exhibit 12 circuit description. Ericsson AB requests confidentiality under CFR 0.459 according to attached letter. We further certify that the applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to section 5301 of the Anti-Drug abuse Act of 1988, 21 U.S.C. Section 862. If additional information is needed, please contact me on the below listed number . David Bolzon Senior RF Engineer, Ericsson Canada 349 Terry Fox Drive Ottawa, Ontario, Canada, K2K 2V6 Telephone No.: 613-963-6998 e-mail: [email protected]

Ericsson Canada Proprietary Information RD 2242 B5 Restricted Use and Duplication FCC ID: TA8AKRY901332-1 IC ID: 287AB-AS9013321 EMC/LB/F Regulatory Compliance 12/03/2015 Page 1 of 4 Exhibit 3: External Photographs KRY 901 332/1 Photo Submission (External) RD 2242 B5 FCC ID: TA8AKRY901332-1 IC ID: 287AB-AS9013321 IC Model: AS9013321 Date: 12 March 2015 Author: Ericsson EMC File: RD 2242 B5 Photos External CONFIDENTIAL INFORMATION RESTRICTED USE AND DUPLICATION © Ericsson Canada Inc. All Rights Reserved. The information contained in this document is the property of Ericsson Canada. Except as specifically authorized in writing by Ericsson, the holder of this document shall keep all information contained herein confidential and shall protect same in whole or in part from disclosure and dissemination to all third parties. Ericsson Canada Proprietary Information RD 2242 B5 Restricted Use and Duplication FCC ID: TA8AKRY901332-1 IC ID: 287AB-AS9013321 EMC/LB/F Regulatory Compliance 12/03/2015 Page 2 of 4 Figure 1: RD 2242 B5 Top (Radome) View Figure 2: RD 2242 B5 Bottom View Ericsson Canada Proprietary Information RD 2242 B5 Restricted Use and Duplication FCC ID: TA8AKRY901332-1 IC ID: 287AB-AS9013321 EMC/LB/F Regulatory Compliance 12/03/2015 Page 3 of 4 Figure 3: RD 2242 B5 Side View_1 Figure 4: RD 2242 B5 Side View_2 Ericsson Canada Proprietary Information RD 2242 B5 Restricted Use and Duplication FCC ID: TA8AKRY901332-1 IC ID: 287AB-AS9013321 EMC/LB/F Regulatory Compliance 12/03/2015 Page 4 of 4 Figure 5: RD 2242 B5 Side View_1 with Mount Figure 6: RD 2242 B5 Side View_2 with Mount

Ex 06 FC IC IC Fi xhibit 01: P 6 April 2015 CC ID: TA8AK ID: 287AB-A Model: AS90 igure 1: R Product Ide KRY901332-1 AS9013321 013321 RD 2242 B entification 1 B5 Label D n Label Detail Ericsson C K Canada Conf RY 901 332/1 fidential 1

1 (6) EAB-15:015318 Uen, Rev A, 2015-03-06 © Telefonaktiebolaget LM Ericsson AB. This report shall not be reproduced except in full, without written approval of the laboratory. Rapport utfärdad av ackrediterat provningslaboratorium Test report issued by an Accredited Testing Laboratory EMF Test Report: Ericsson RD 2242 B5 R1B Document number: EAB-15:015318 Uen Rev A Date of report: 2015-03-06 Testing laboratory: Ericsson EMF Research Laboratory Ericsson AB SE-164 80 Stockholm Sweden Company/Client: FJB/RIC Tanvir Alam EMC 349 Terry Fox Drive Ottawa, K2K 2V6 Canada Tests performed by: Björn Thors Dates of tests: 2015-03-06 Manufacturer and market name(s) of device: Ericsson RD 2242 B5 R1B Testing has been performed in accordance with: FCC CFR title 47, part 1.1310, FCC OET Bulletin 65, FCC KDB447498 D01, Industry Canada RSS 102 Test results: The tested device complies with the requirements in respect of all parameters subject to the test. Additional information: Testing was conducted for mobile exposure conditions Signature: Test Engineer ____________________________________________ Björn Thors Senior Specialist - RF Exposure Assessment [email protected] Tel: +46 10 717 1824 Deputy Quality Manager ____________________________________________ Jaroslav Kazejev Experienced Researcher [email protected] Tel: +46 10 7134344 2 (6) EAB-15:015318 Uen, Rev A, 2015-03-06 1 Summary of EMF Test Report 1 Frequency Band [MHz] B5 Modes LTE Supported  Covered by report  Exposure environment General public 1.1 Results RF exposure assessment results for general public (uncontrolled) exposure applicable in USA and Canada [1] - [5] are given in the table below. The equipment under test (EUT) conforms to the requirements of the relevant standards when the combined exposure ratio is less than one. RF exposure assessment results for general public (uncontrolled) exposure as obtained for the RDS together with an assumed output power tolerance of 2.0 dB and a transmission loss of 0.5 dB using procedures applicable for the US and Canadian markets [3], [4]. 3GPP band Standard Nominal output power from the radio Test position Test separation distance Exposure ratio Result B5 (850) L 2 x 0.05 W Direction of maximum gain 20 cm 0.1 PASSED 1 This page contains a summary of the test results. The full report provides a complete description of all test details and results. 3 (6) EAB-15:015318 Uen, Rev A, 2015-03-06 2 General information The test results reported in this document have been obtained by simple calculations according to plane-wave equivalent conditions [4]. The purpose of the tests was to verify that the EUT is in compliance with the appropriate RF exposure standards, recommendations and limits [1] - [5]. 3 Equipment under test Table 1 summarizes the technical data for the EUT. Photographs of the EUT are presented in Appendix A. Table 1 Technical data for the EUT. Product name RD 2242 B5 R1B Product tested KRY 901 332/1 Dimensions, Thickness x Diameter (mm) 50 x 109 Configurations(s) covered by this report LTE 850 (B5) Antenna(s) Internal antennas Product number Maximum gain (dBi) KRE 101 2187/1 -0.4 dBi Transmitter frequency range (MHz) LTE 850 (B5): 869 -894 In Table 2 nominal output power levels are given. Table 2 Nominal output power levels. 4 EMF exposure assessments FCC procedures [4] specify exposure assessment methods to verify compliance with EMF exposure limits [1] of mobile devices. A minimum test separation distance of at least 20 cm is required between the device and nearby persons to apply mobile device exposure limits. The test separation distance for which the equipment is shown to comply with the exposure limits must be clearly provided in the operating and installation instructions. 4.1 Field strength calculations The maximum gain, 퐺 ANT , of the two antennas used is -0.4 dBi (0.91), see Table 1. Assuming correlated transmit signals, the directional gain, 퐺, may be taken as 2.6 dBi according to [6]. This is most likely a very conservative assumption given the used transmission modes and antenna topology. The total effective radiated power for the omni-directional antennas is 0.2 W. As a consequence, the categorical exclusion provision of FCC CFR title 47, § 2.1091(c) [7] and the exemption from routine evaluation in Industry Canada RSS-102 [3] apply. Therefore, the minimum test separation distance may be estimated by simple calculations according to plane-wave equivalent conditions [4]. The exposure ratio, 퐸푅, may be conservatively estimated as 2 Nominal output power per port. 3 Conservative measure of the total maximum possible output power level delivered to the antennas including losses and tolerances. Band / Mode Nominal output power 2 (dBm) Tolerance, upper limit (dB) Transmission loss (dB) Maximum output power 3 (dBm) LTE B5 (850), 2x50mW 17 2.0 0.5 21.5 4 (6) EAB-15:015318 Uen, Rev A, 2015-03-06 퐸푅= 푆 est 푆 lim = 푃 tot 퐺 4휋푟 2 푆 lim , where P tot : Total conducted power for the cellular bands (21.5 dBm), G: Directional gain (2.6 dBi), 푟: Separation distance from antenna, 푆 lim : Power density exposure limit of 5.8 W/m 2 . Setting 푃 tot = 0.141 W, 퐺=1.82, 푟 = 0.20 m and 푆 lim = 5.8 W/m 2 gives the result for a 20 cm test separation distance in Table 3. Table 3 RF exposure assessment results for general public (uncontrolled) exposure as obtained for the RDS using procedures applicable for the US and Canadian markets [3], [4]. 3GPP band Standard Nominal output power from the radio Test position 4 Test separation distance 5 Exposure ratio Result B5 (850) L 2 x 0.05 W Direction of maximum gain 20 cm 0.1 PASSED The exposure ratio is well below one. Hence, the RF EMF exposure is below the relevant exposure limits [1] for the 20 cm test separation distance. 5 Conclusion The results in Section 4 show that the plane-wave equivalent power density, estimated according to the requirements of FCC [4] and Industry Canada [3], is below the relevant exposure limits [1], [5] at a sepa…

Text truncated - open the document above for the full version.

Document 75929787 Report 01 Issue 1 April 2015 Report On FCC and IC Testing of the Ericsson RD 2242 B5 (869-894 MHz) WCDMA/LTE Base Station In accordance with FCC CFR 47 Part 2 and 22 and Industry Canada RSS-132 and RSS-GEN COMMERCIAL-IN-CONFIDENCE FCC ID: TA8AKRY901332-1 IC: 287AB-AS9013321 PREPARED BY APPROVED BY DATED 02 April 2015 Neil Rousell Nic Forsyth Senior Engineer (RF) Authorised Signatory Document 75929787 Report 01 Issue 1 Page 1 of 120 CONTENTS Section Page No 1 REPORT INFORMATION ............................................................................................................ 2 1.1 Report Details ................................................................................................................................ 3 1.2 Brief Summary of Results .............................................................................................................. 4 1.3 Configuration Description .............................................................................................................. 5 1.4 Declaration of Build Status ............................................................................................................ 7 1.5 Product Information ....................................................................................................................... 8 1.6 Test Setup ..................................................................................................................................... 9 1.7 Test Conditions ............................................................................................................................ 10 1.8 Deviation From The Standard ..................................................................................................... 10 1.9 Modification Record ..................................................................................................................... 10 1.10 Alternative Test Site..................................................................................................................... 10 1.11 Additional Information .................................................................................................................. 10 2 TEST DETAILS .......................................................................................................................... 11 2.1 Maximum Peak Output Power and Peak to Average Ratio - Conducted .................................... 12 2.2 Occupied Bandwidth .................................................................................................................... 25 2.3 Band Edge ................................................................................................................................... 40 2.4 Transmitter Spurious Emissions .................................................................................................. 60 2.5 Frequency Stability .................................................................................................................... 112 3 TEST EQUIPMENT USED ....................................................................................................... 115 3.1 Test Equipment Used ................................................................................................................ 116 3.2 Measurement Uncertainty ......................................................................................................... 118 4 ACCREDITATION, DISCLAIMERS AND COPYRIGHT .......................................................... 119 4.1 Accreditation, Disclaimers and Copyright .................................................................................. 120 ANNEX A Module Lists .............................................................................................................................. A.2 Document 75929787 Report 01 Issue 1 Page 2 of 120 SECTION 1 REPORT INFORMATION Document 75929787 Report 01 Issue 1 Page 3 of 120 1.1 REPORT DETAILS Manufacturer Ericsson Address 349 Terry Fox Drive Ottawa Ontario K2K 2V6 Product Name RD 2242 B5 Product Number KRY 901 332/1 IC Model Name AS9013321 Serial Number(s) C829459692 Software Version CXP9013268/14_R59FK Hardware Version R1B Test Specification/Issue/Date FCC CFR 47 Part 2: 2014 FCC CFR 47 Part 22: 2014 Industry Canada RSS-132 Issue 3: 2013 Start of Test 16 March 2015 Finish of Test 19 March 2015 Name of Engineer(s) Neil Rousell Related Document(s) Industry Canada RSS-GEN Issue 4: 2014 Document 75929787 Report 01 Issue 1 Page 4 of 120 1.2 BRIEF SUMMARY OF RESULTS A brief summary of results for each configuration, in accordance with FCC CFR 47 Part 2 and 22 and Industry Canada RSS-132 and RSS-GEN is shown below. Section Spec Clause Test Description Result Part 2 Part 22 RSS-GEN / RSS 132 2.1 2.1046 22.913(a) 5.4 Maximum Peak Output Power – Conducted Pass 2.2 2.1049(h) 22.917(b) 6.6 Occupied Bandwidth Pass 2.3 2.1051 22.917(b) 22.905(a)(b) 5.5 Spurious Emissions at Band Edge Pass 2.4 2.1051 22.917(a)(b) 5.5 Conducted Spurious Emissions Pass 2.5 2.1055 (d)(1),(b) 22.355 6.11 / 5.3 Frequency Stability Under Temperature Variations Pass 2.6 2.1055(d)(1) 22.355 6.11 / 5.3 Frequency Stability Under Voltage Variations Pass - - - 7.1 / 5.6 Receiver Spurious Emissions Pass * - 2.1051 22.917(a)(b) 6.13 Transmitter Radiated Emissions Pass* * - Reference Flextronics Design Validation Centre, Canada EMC Test Report: Reference Number K002569-TR-EMC-05_R1 Flextronics Canada Design Services Inc. 1280 Teron Side Road Kanata, Ontario, K2K 2C1 Canada Accreditations (Flextronics) The Design Validation Centre (DVC) test facilities are accredited by the Standards Council of Canada (SCC) to ISO/IEC 17025 in accordance with the scope of accreditation outlined at the web site http://palcan.scc.ca/Specs/PDF/95_e.pdf. The SCC is a signatory of the APLAC [4] and ILAC [14] Mutual Recognition Arrangements. The SCC's Laboratory Accreditation Program has been evaluated and has demonstrated its competence to op…

Text truncated - open the document above for the full version.

Ericsson Canada Proprietary Information RD 2242 B5 Restricted Use and Duplication FCC ID: TA8AKRY901332-1 IC ID: 287AB-AS9013321 EMC/LB/F Regulatory Compliance 26/03/2015 Page 1 of 6 Exhibit 3: EMC Set Up Photographs KRY 901 332/1 EMC Photo Submission – Radiated Emissions RD 2242 B5 FCC ID: TA8AKRY901332-1 IC ID: 287AB-AS9013321 IC Model: AS9013321 Date: 6 April 2015 Author: Ericsson EMC File: Exhibit 03 Photos EMC Setup RD 2242 B5 CONFIDENTIAL INFORMATION RESTRICTED USE AND DUPLICATION © Ericsson Canada Inc. All Rights Reserved. The information contained in this document is the property of Ericsson Canada. Except as specifically authorized in writing by Ericsson, the holder of this document shall keep all information contained herein confidential and shall protect same in whole or in part from disclosure and dissemination to all third parties. Ericsson Canada Proprietary Information RD 2242 B5 Restricted Use and Duplication FCC ID: TA8AKRY901332-1 IC ID: 287AB-AS9013321 EMC/LB/F Regulatory Compliance 26/03/2015 Page 2 of 6 Figure 1 Radiated Emissions Test Setup Ericsson Canada Proprietary Information RD 2242 B5 Restricted Use and Duplication FCC ID: TA8AKRY901332-1 IC ID: 287AB-AS9013321 EMC/LB/F Regulatory Compliance 26/03/2015 Page 3 of 6 Figure 2 Radiated Emissions Test Setup (Close up) Ericsson Canada Proprietary Information RD 2242 B5 Restricted Use and Duplication FCC ID: TA8AKRY901332-1 IC ID: 287AB-AS9013321 EMC/LB/F Regulatory Compliance 26/03/2015 Page 4 of 6 Figure 3 Test Antenna (1 to 10 GHz) Ericsson Canada Proprietary Information RD 2242 B5 Restricted Use and Duplication FCC ID: TA8AKRY901332-1 IC ID: 287AB-AS9013321 EMC/LB/F Regulatory Compliance 26/03/2015 Page 5 of 6 Figure 4 Test Antenna (30 MHz to 1 GHz) Ericsson Canada Proprietary Information RD 2242 B5 Restricted Use and Duplication FCC ID: TA8AKRY901332-1 IC ID: 287AB-AS9013321 EMC/LB/F Regulatory Compliance 26/03/2015 Page 6 of 6 Figure 5 Substitution Test Setup