TJ7BTK-503Bluetooth speakers

1 Bluetooth Speaker BTK-503 User Manual Playing on/off PREV NEXT Checking the accessories Make sure that you have the following items with your speaker: USB Charging cable, 3.5mm audio cable & Manual. Charging the speaker Your speaker uses a rechargeable battery. You must charge the battery fully before using the speaker for the first time. 1. Plug the USB Cable into PC socket. 2. Connect the USB Cable with speaker as it shown on the picture. The red indicator of headset will turn on when charging. 3. When the battery is fully charged, the red indicator will turn blue 1) When the speaker is in low battery, the indicator will flash red and tone as “battery low” once in a minute. 2) The speaker will be fully charged in approximately 5-6 hours. 2 3) Remove the USB cable from the PC socket IMPORTANT: The speaker can be used while charging. BASIC OPERATIONS Turning Speaker on/off 1. To turn the speaker on Switch the “on/off” Button to the left, you will hear a tone “power on”. The speaker is now turned on. 2. To turn the speaker off Switch the “on/off” Button to the right, you will hear a tone “power off”. The speaker will be turned off. 3. When the speaker is on low battery, blue indicator will flash red during standby mode and will voice for “battery low”. Please charge the speaker. Pairing Pairing will create a unique and enciphered wireless link between two Bluetooth enabled devices, such as your Bluetooth phone and Bluetooth speaker. 1. Ensure that the speaker is on standby mode or playing mode. 2. Press and hold the “playing on/off” Button for about 2 seconds until the indicator light alternately flashes blue and red. You will hear a tone “pairing”, which means the speaker has been in pairing mode. 3. Set your Bluetooth phone to discover the speaker by following your phone's guide. Typically, the steps involve going to a ‘Setup’, 'Connect', or ‘Bluetooth’ menu on your phone and then selecting the option to discover Bluetooth devices. 4. Your phone will find the speaker and ask if you want to pair with it. Confirm this by pressing the “Yes” or “OK” key. 5. Enter a passkey or PIN code “0000” (4 zeros), then press the “Yes” or “OK” key. Note: If the Bluetooth version of your Bluetooth mobile phone is V3.0, you will not need to enter a Passkey (Pin code) during above pairing process. 6. You will hear a tone “connected”, it means your phone has been connected with the speaker. Playing on/off 1. Make sure that your phone connected with the speaker. 2. Find music in your phone and play on, the song will be playing from the speaker. 3. Press “Playing on/off” button when playing on, the song will be stop. Changing music 3 When the speaker is playing on, press “PREV” or “NEXT” button once to change music. This feature may vary due to user’s operation mode and mobile phone settings. Adjust the volume 1. Press “VOL-” to decrease the volume and you will hear a beep when it is minimum 2. Press “VOL+” to increase the volume and you will hear a beep when it is maximum. Making a call Using the phone’s keypad 1. Dial number on the keypad or select the contact name from the contact list of your mobile phone. 2. Press phone’s “send/call” key. This feature may vary due to user’s operation mode and mobile phone settings. You may need to transfer the call from phone to the speaker----see “transferring a call” part. Voice Dialing Please ensure your mobile phone supports voice dialing function and the voice tag assigned for this feature. Connected with one mobile phone: 1. Press “PREV” or “NEXT” Button for 2 seconds. 2. You’ll then hear the voice-activation tone, say the name of the person you wish to call. 3. Press “PREV” or “NEXT” Button for 2 seconds to stop the voice dialing. Ending a call 1. Shortly press “Playing on/off” Button once during a call. 2. End a call from phone’s keypad. Answering a call 1. Press the “Playing on/off” button briefly, when you receiving an incoming call. 2. Answer the call via your phone’s keypad. You may then need to transfer the call to the speaker by pressing the “Playing on/off” Button for 2 seconds (depending on your phone setting). Last number redialing Connected with one mobile phone: Shortly press “Playing on/off” Button twice to make the last number redial. Rejecting an incoming call Press and hold “Playing on/off” Button for 2 seconds to reject a call. Transferring a call Spesker to phone: Press and hold “Playing on/off” Button for 2 seconds during a call, then release it. Phone to speaker : Press and hold “Playing on/off” Button for 2 seconds during a call, then release it. 4 Note: For different mobile phone setting, you could only transfer a call by press the mobile phone’s keypad. Depend on your phone type, the actual operation may vary. Muting the Microphone You can put a call on hold by muting the microphone. To turn on/turn off the Muting Microphone function: Press the “VOL+” Button & “VOL-” Button at the same time. Delete the pairing records When the speaker is on standby mode, press “VOL+” Button & “VOL-” Button for 5 seconds. DFU mode Connected USB cable with speaker, press “PREV” or “NEXT” button for 5 seconds when speaker is on standby mode or playing mode. Crash and reset Connected USB cable with speaker and press “VOL+” & “VOL-” button once to reset the speaker. Adjust the EQ When the speaker in on playing mode, press “NEXT” button for 2 seconds, it will switch circularly among “normal”, “bass”, “treble”. Storage of the speaker 1. Always store the speaker with the power off and make sure it is safely protected. 2. Avoid storage at high temperatures (above 60°C) such as in a hot vehicle or in direct sunlight. (Storage at high temperatures can damage performance and reduces battery life). 3. Do not expose the speaker or any of its supplied parts to rain or other liquids. Product Specifications Bluetooth Compliance: Bluetooth Version4.0 Specifications Support Bluetooth HSP, HFP, A2DP and AVRCP Profiles Multipoint A2DP connection Wire audio support (line in) Pl…

Text truncated - open the document above for the full version.

Shenzhen SHI KISB Electronic Co., Ltd. DATE: 2013-1-15 To whom it may concern: We, the undersigning company Name: Shenzhen SHI KISB Electronic Co., Ltd. Address: 3-5F, A Building, Shanghe Industrial Zone, Nanchang Road, Bao'an District, City: Shenzhen Country: China Declare that: Name Representative of agent: Ms. Cathy Wang Agent Company name: Neutron Engineering, Inc. Address: No.3 Jinshagang 1st Road, Shixia, Dalang Town City: Dongguan Country: China is authorized to apply for Certification of the following product(s):Product description: Bluetooth speakers Type designation: BTK-502;BTK-503;BTK-505;BTK-506;BTK-507;BTK-508; BTK- 509;BTK-28; BTK-30; BTK-31;BTK-32; BTK-33; BTK-35; BTK-36 Trademark: KISS; BTK Sincerely, (Name and Title) KK Lee , General Manager

Shenzhen SHI KISB Electronic Co., Ltd. Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Gentlemen: This letter is to comply with Sections 0.457 and 0.459 pertaining to confidential material. Shenzhen SHI KISB Electronic Co., Ltd. would like the following documents regarding this submission for FCC ID: TJ7BTK-503 to be kept confidential. 1. Schematic 2. Block diagram 3. Circuit description The above material contains trade secrets or technical data, which would customarily be guarded from competitors. We do not want these documents to be accessible to the general public. Sincerely, Name: KK Lee Title: General Manager 2013-01-15

Neutron Engineering Inc. Project No.: 1212C272 Page 2 of 10 Neutron Engineering Inc. Project No.: 1212C272 Page 3 of 10 Neutron Engineering Inc. Project No.: 1212C272 Page 4 of 10

Neutron Engineering Inc. Project No.: 1212C272 Page 5 of 10 Neutron Engineering Inc. Project No.: 1212C272 Page 6 of 10 Neutron Engineering Inc. Project No.: 1212C272 Page 7 of 10 Neutron Engineering Inc. Project No.: 1212C272 Page 8 of 10 Neutron Engineering Inc. Project No.: 1212C272 Page 9 of 10 Neutron Engineering Inc. Project No.: 1212C272 Page 10 of 10

Neutron Engineering Inc. Report No.: NEI-FCCP-1-1212C272 Page 1 of 103 FCC Radio Test Report FCC ID: TJ7BTK-503 This report concerns (check one) : Original Grant Class II Change Issued Date : Jan. 21, 2013 Project No. : 1212C272 Equipment : Bluetooth speakers Model Name : BTK-502; BTK-503; BTK-505; BTK-506; BTK-507; BTK-508; BTK-509; BTK-28; BTK-30; BTK-31; BTK-32; BTK-33; BTK-35; BTK-36 Applicant : ShenZhen SHI KISB Electronic Co., LTD Address : 3-5F, A Building, Shanghe Industrial Zone, Nanchang Road, Bao’an District, Shenzhen, China Manufacturer : ShenZhen SHI KISB Electronic Co., LTD Address : 3-5F, A Building, Shanghe Industrial Zone, Nanchang Road, Gushu Village, Xixiang Town, Bao’an District, Shenzhen, Guangdong, China Tested by: Neutron Engineering Inc. EMC Laboratory Date of Receipt: Jan. 11, 2013 Date of Test: Jan. 11, 2013 ~ Jan. 20, 2013 Testing Engineer : (David Mao) Technical Manager : (Leo Hung) Authorized Signatory : (Steven Lu) Neutron Engineering Inc. No.3,Jinshagang 1st Road, ShiXia, Dalang Town, Dong Guan, China. TEL : (0769) 8318-3000 FAX : (0769) 8319-6000 Neutron Engineering Inc. Report No.: NEI-FCCP-1-1212C272 Page 2 of 103 Declaration Neutron represents to the client that testing is done in accordance with standard procedures as applicable and that test instruments used has been calibrated with the standards traceable to National Measurement Laboratory (NML) of CHINA, or National Institute of Standards and Technology (NIST) of U.S.A. Neutron's reports apply only to the specific samples tested under conditions. It is manufacture’s responsibility to ensure that additional production units of this model are manufactured with the identical electrical and mechanical components. Neutronshall have no liability for any declarations, inferences o r generalizations drawn by the client or others from Neutron issued reports. Neutron’s reports must not be used by the client to claim product endorsement by the authorities or any agency of the Government. This report is the confidential property of the client. As a mutual protection to the clients, the public and Neutron-self, extracts from the test report shall not be reproduced except in full with Neutron’s authorized written approval. Neutron’s laboratory quality assurance procedures are in compliance with the ISO Guide 17025 requirements, and accredited by the conformity assessment authorities listed in this test report. Limitation For the use of the authority's logo is limited unless the Test Standard(s)/Scope(s)/Item(s) mentioned in this test report is (are) included in the conformity assessment authorities acceptance respective. Neutron Engineering Inc. Report No.: NEI-FCCP-1-1212C272 Page 3 of 103 Table of Contents Page 1 . CERTIFICATION 5 2 . SUMMARY OF TEST RESULTS 6 2.1 TEST FACILITY 7 2.2 MEASUREMENT UNCERTAINTY 7 3 . GENERAL INFORMATION 8 3.1 GENERAL DESCRIPTION OF EUT 8 3.2 DESCRIPTION OF TEST MODES 10 3.3 TABLE OF PARAMETERS OF TEXT SOFTWARE SETTING 10 3.4 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 11 3.5 DESCRIPTION OF SUPPORT UNITS 12 4 . EMC EMISSION TEST 13 4.1 CONDUCTED EMISSION MEASUREMENT 13 4.1.1 POWER LINE CONDUCTED EMISSION LIMITS 13 4.1.2 MEASUREMENT INSTRUMENTS LIST AND SETTING 13 4.1.3 TEST PROCEDURE 14 4.1.4 DEVIATION FROM TEST STANDARD 14 4.1.5 TEST SETUP 14 4.1.6 EUT OPERATING CONDITIONS 14 4.1.7 TEST RESULTS 15 4.2 RADIATED EMISSION MEASUREMENT 18 4.2.1 RADIATED EMISSION LIMITS 18 4.2.2 MEASUREMENT INSTRUMENTS LIST ANS SETTING 19 4.2.3 TEST PROCEDURE 20 4.2.4 DEVIATION FROM TEST STANDARD 20 4.2.5 TEST SETUP 21 4.2.6 EUT OPERATING CONDITIONS 22 4.2.7 TEST RESULTS (BELOW 30MHZ) 23 4.2.8 TEST RESULTS (BETWEEN30 – 1000 MHZ) 24 4.2.9 TEST RESULTS (ABOVE 1000 MHZ) 31 5 . NUMBER OF HOPPING CHANNEL 55 5.1 APPLIED PROCEDURES / LIMIT 55 5.1.1 MEASUREMENT INSTRUMENTS LIST AND SETTING 55 5.1.2 TEST PROCEDURE 55 5.1.3 DEVIATION FROM STANDARD 55 5.1.4 TEST SETUP 55 5.1.5 EUT OPERATION CONDITIONS 55 5.1.6 TEST RESULTS 56 6 . AVERAGE TIME OF OCCUPANCY 58 Neutron Engineering Inc. Report No.: NEI-FCCP-1-1212C272 Page 4 of 103 Table of Contents Page 6.1 APPLIED PROCEDURES / LIMIT 58 6.1.1 MEASUREMENT INSTRUMENTS LIST 58 6.1.2 TEST PROCEDURE 58 6.1.3 DEVIATION FROM STANDARD 58 6.1.4 TEST SETUP 59 6.1.5 EUT OPERATION CONDITIONS 59 6.1.6 TEST RESULTS 60 7 . HOPPING CHANNEL SEPARATION MEASUREMENT 72 7.1 APPLIED PROCEDURES / LIMIT 72 7.1.1 MEASUREMENT INSTRUMENTS LIST AND SETTING 72 7.1.2 TEST PROCEDURE 72 7.1.3 DEVIATION FROM STANDARD 72 7.1.4 TEST SETUP 72 7.1.5 EUT OPERATION CONDITIONS 72 7.1.6 TEST RESULTS 73 8 . BANDWIDTH TEST 77 8.1 APPLIED PROCEDURES / LIMIT 77 8.1.1 MEASUREMENT INSTRUMENTS LIST AND SETTING 77 8.1.2 TEST PROCEDURE 77 8.1.3 DEVIATION FROM STANDARD 77 8.1.4 TEST SETUP 77 8.1.5 EUT OPERATION CONDITIONS 77 8.1.6 TEST RESULTS 78 9 . PEAK OUTPUT POWER TEST 82 9.1 APPLIED PROCEDURES / LIMIT 82 9.1.1 MEASUREMENT INSTRUMENTS LIST AND SETTING 82 9.1.2 TEST PROCEDURE 82 9.1.3 DEVIATION FROM STANDARD 82 9.1.4 TEST SETUP 82 9.1.5 EUT OPERATION CONDITIONS 82 9.1.6 TEST RESULTS 83 10 . ANTENNA CONDUCTED SPURIOUS EMISSION 87 10.1 APPLIED PROCEDURES / LIMIT 87 10.1.1 MEASUREMENT INSTRUMENTS LIST AND SETTING 87 10.1.2 TEST PROCEDURE 87 10.1.3 DEVIATION FROM STANDARD 87 10.1.4 TEST SETUP 87 10.1.5 EUT OPERATION CONDITIONS 87 10.1.6 TEST RESULTS 88 11 . EUT TEST PHOTO 100 Neutron Engineering Inc. Report No.: NEI-FCCP-1-1212C272 Page 5 of 103 1. CERTIFICATION Equipment : Bluetooth speakers Brand Name : KISS; BTK Model Name : BTK-502; BTK-503; BTK-505; BTK-506; BTK-507; BTK-508; BTK-509; BTK-28; BTK-30; BTK-31; BTK-32; BTK-33; BTK-35; BTK-36 Applicant : ShenZhen SHI KISB Electronic Co., LTD Factory : ShenZhen SHI KISB Electronic Co., LTD Address : 3-5F, A Building, Shanghe Industrial Zone, Nanchang Road, Gushu Village, Xixiang Town, Bao’an District, Shenzhen, Guangdong, China Date of Test : Jan. 11, 2013 ~ Jan. 20, 2013 Test Item : ENGINEERING SAMPLE Standards : FCC Part15, Subpart C(15.247) / ANSI C63.4 …

Text truncated - open the document above for the full version.

Neutron Engineering Inc. Report No.: NEI-FCCP-2-1212C272 Page 1 of 63 FCC Radio Test Report FCC ID: TJ7BTK-503 This report concerns (check one) : Original Grant Class II Change Issued Date : Jan. 21, 2013 Project No. : 1212C272 Equipment : Bluetooth speakers Model Name : BTK-502; BTK-503; BTK-505; BTK-506; BTK-507; BTK-508; BTK-509; BTK-28; BTK-30; BTK-31; BTK-32; BTK-33; BTK-35; BTK-36 Applicant : ShenZhen SHI KISB Electronic Co., LTD Address : 3-5F, A Building, Shanghe Industrial Zone, Nanchang Road, Bao’an District, Shenzhen, China Manufacturer : ShenZhen SHI KISB Electronic Co., LTD Address : 3-5F, A Building, Shanghe Industrial Zone, Nanchang Road, Gushu Village, Xixiang Town, Bao’an District, Shenzhen, Guangdong, China Tested by: Neutron Engineering Inc. EMC Laboratory Date of Receipt: Jan. 11, 2013 Date of Test: Jan. 11, 2013 ~ Jan. 20, 2013 Testing Engineer : (David Mao) Technical Manager : (Leo Hung) Authorized Signatory : (Steven Lu) Neutron Engineering Inc. No.3,Jinshagang 1st Road, ShiXia, Dalang Town, Dong Guan, China. TEL : (0769) 8318-3000 FAX : (0769) 8319-6000 Neutron Engineering Inc. Report No.: NEI-FCCP-2-1212C272 Page 2 of 63 Declaration Neutron represents to the client that testing is done in accordance with standard procedures as applicable and that test instruments used has been calibrated with the standards traceable to National Measurement Laboratory (NML) of R.O.C, or National Institute of Standards and Technology (NIST) of U.S.A. Neutron's reports apply only to the specific samples tested under conditions. It is manufacture’s responsibility to ensure that additional production units of this model are manufactured with the identical electrical and mechanical components. Neutronshall have no liability for any declarations, inferences o r generalizations drawn by the client or others from Neutron issued reports. Neutron’s reports must not be used by the client to claim product endorsement by the authorities or any agency of the Government. This report is the confidential property of the client. As a mutual protection to the clients, the public and Neutron-self, extracts from the test report shall not be reproduced except in full with Neutron’s authorized written approval. Neutron’s laboratory quality assurance procedures are in compliance with the ISO Guide 17025 requirements, and accredited by the conformity assessment authorities listed in this test report. Limitation For the use of the authority's logo is limited unless the Test Standard(s)/Scope(s)/Item(s) mentioned in this test report is (are) included in the conformity assessment authorities acceptance respective. Neutron Engineering Inc. Report No.: NEI-FCCP-2-1212C272 Page 3 of 63 Table of Contents Page 1 . CERTIFICATION 5 2 . SUMMARY OF TEST RESULTS 6 2.1 TEST FACILITY 7 2.2 MEASUREMENT UNCERTAINTY 7 3 . GENERAL INFORMATION 8 3.1 GENERAL DESCRIPTION OF EUT 8 3.2 DESCRIPTION OF TEST MODES 10 3.3 TABLE OF PARAMETERS OF TEXT SOFTWARE SETTING 11 3.4 BLOCK DIAGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 12 3.5 DESCRIPTION OF SUPPORT UNITS 13 4 . EMC EMISSION TEST 14 4.1 CONDUCTED EMISSION MEASUREMENT 14 4.1.1 POWER LINE CONDUCTED EMISSION LIMITS 14 4.1.2 MEASUREMENT INSTRUMENTS LIST AND SETTING 14 4.1.3 TEST PROCEDURE 15 4.1.4 DEVIATION FROM TEST STANDARD 15 4.1.5 TEST SETUP 15 4.1.6 EUT OPERATING CONDITIONS 15 4.1.7 TEST RESULTS 16 4.2 RADIATED EMISSION MEASUREMENT 21 4.2.1 RADIATED EMISSION LIMITS 21 4.2.2 MEASUREMENT INSTRUMENTS LIST ANS SETTING 22 4.2.3 TEST PROCEDURE 23 4.2.4 DEVIATION FROM TEST STANDARD 23 4.2.5 TEST SETUP 24 4.2.6 EUT OPERATING CONDITIONS 25 4.2.8 TEST RESULTS-BETWEEN 30MHZ AND 1000MHZ 27 4.2.7 TEST RESULTS (ABOVE 1000 MHZ) 34 5 . BANDWIDTH TEST 46 5.1 APPLIED PROCEDURES / LIMIT 46 5.1.1 MEASUREMENT INSTRUMENTS LIST 46 5.1.2 TEST PROCEDURE 46 5.1.3 DEVIATION FROM STANDARD 46 5.1.4 TEST SETUP 46 5.1.5 EUT OPERATION CONDITIONS 46 5.1.6 TEST RESULTS 47 6 . MAXIMUM OUTPUT POWER TEST 49 Neutron Engineering Inc. Report No.: NEI-FCCP-2-1212C272 Page 4 of 63 Table of Contents Page 6.1 APPLIED PROCEDURES / LIMIT 49 6.1.1 MEASUREMENT INSTRUMENTS LIST 49 6.1.2 TEST PROCEDURE 49 6.1.3 DEVIATION FROM STANDARD 49 6.1.4 TEST SETUP 49 6.1.5 EUT OPERATION CONDITIONS 49 6.1.6 TEST RESULTS 50 7 . ANTENNA CONDUCTED SPURIOUS EMISSION 51 7.1 APPLIED PROCEDURES / LIMIT 51 7.1.1 MEASUREMENT INSTRUMENTS LIST 51 7.1.2 TEST PROCEDURE 51 7.1.3 DEVIATION FROM STANDARD 51 7.1.4 TEST SETUP 51 7.1.5 EUT OPERATION CONDITIONS 51 7.1.6 TEST RESULTS 52 8 . POWER SPECTRAL DENSITY TEST 57 8.1 APPLIED PROCEDURES / LIMIT 57 8.1.1 MEASUREMENT INSTRUMENTS LIST 57 8.1.2 TEST PROCEDURE 57 8.1.3 DEVIATION FROM STANDARD 57 8.1.4 TEST SETUP 57 8.1.5 EUT OPERATION CONDITIONS 57 8.1.6 TEST RESULTS 58 9 . EUT TEST PHOTO 60 Neutron Engineering Inc. Report No.: NEI-FCCP-2-1212C272 Page 5 of 63 1. CERTIFICATION Equipment : Bluetooth speakers Brand Name : KISS; BTK Model Name : BTK-502; BTK-503; BTK-505; BTK-506; BTK-507; BTK-508; BTK-509; BTK-28; BTK-30; BTK-31; BTK-32; BTK-33; BTK-35; BTK-36 Applicant : ShenZhen SHI KISB Electronic Co., LTD Factory : ShenZhen SHI KISB Electronic Co., LTD Address : 3-5F, A Building, Shanghe Industrial Zone, Nanchang Road, Gushu Village, Xixiang Town, Bao’an District, Shenzhen, Guangdong, China Date of Test : Jan. 11, 2013 ~ Jan. 20, 2013 Test Item : ENGINEERING SAMPLE Standards : FCC Part15, Subpart C(15.247) / ANSI C63.4-2009 The above equipment has been tested and found compliance with the requirement of the relative standards by Neutron Engineering Inc. EMC Laboratory. The test data, data evaluation, and equipment configuration contained in our test report (Ref No. NEI-FCCP-2-1212C272) were obtained utilizing the test procedures, test instruments, test sites that has been accredited by the Authority of NVLAP and TAF according to the ISO-17025 quality assessment standard and technical standard(s). Neutron Engineering Inc. Report No.: NEI-FCCP-2-1212C272 Page 6 of 63 2. SUMMARY OF TEST RESULTS Test pr…

Text truncated - open the document above for the full version.

Neutron Engineering Inc. Report No.: NEI-FCCP-1-1212C272 Page 61 of 65 9. EUT TEST PHOTO Conducted Measurement Photos Bluetooth Neutron Engineering Inc. Report No.: NEI-FCCP-1-1212C272 Page 63 of 65 Radiated Measurement Photos 9K~30MHz Neutron Engineering Inc. Report No.: NEI-FCCP-1-1212C272 Page 64 of 65 Radiated Measurement Photos 30M~1000MHz Neutron Engineering Inc. Report No.: NEI-FCCP-1-1212C272 Page 65 of 65 Radiated Measurement Photos Above 1000MHz